Skip to contentSkip to conversation

Splashscreen using psplash

DISCUSSION Andreas Enbacka 4 participants 6 messages Apr 23, 2013

lore
Share & tools
lore
#0 lore raw

Hello,

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image, however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Any info would be greatly appreciated.

Best regards,

Andreas Enbacka

#1 lore raw
Quoted 8 lines · Andreas Enbacka

Hello,

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image,
however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot
process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Any info would be greatly appreciated.

You could disable the [framebuffer] console directly in the kernel (CONFIG_FRAMEBUFFER_CONSOLE). With this disabled, Linux will leave whatever was in the framebuffer (possibly a splash put there by your bootstrap).

I've done this where U-Boot put up a splash image that was the same as the psplash one so there was no change on the screen during the boot process until it was completely running.

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#2 lore raw
In reply to Andreas Enbacka
Quoted 8 lines · Andreas Enbacka

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image, however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Passing "quiet" to the kernel (APPEND+="quiet" in local.conf will do it for testing) should stop the majority of the text. A full splash-from-bootloader is possible if you have a bootloader that displays the image, and then a silent kernel from there.

Ross

#3 lore raw

Hello,

Thanks a lot for info, I will try with that.

//Andreas

-----Original Message-----
From: Burton, Ross [mailto:[email protected]]
Sent: 23. huhtikuuta 2013 15:09
To: Andreas Enbacka
Cc: [email protected]
Subject: Re: [yocto] Splashscreen using psplash

Quoted 8 lines · Andreas Enbacka

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image, however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Passing "quiet" to the kernel (APPEND+="quiet" in local.conf will do it for testing) should stop the majority of the text. A full splash-from-bootloader is possible if you have a bootloader that displays the image, and then a silent kernel from there.

Ross

#4 lore raw
Quoted 23 lines · Andreas Enbacka

Hello,

Thanks a lot for info, I will try with that.

//Andreas

-----Original Message-----
From: Burton, Ross [mailto:[email protected]]
Sent: 23. huhtikuuta 2013 15:09
To: Andreas Enbacka
Cc: [email protected]
Subject: Re: [yocto] Splashscreen using psplash

Quoted 8 lines · Andreas Enbacka

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image, however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Quoted 4 lines

Passing "quiet" to the kernel (APPEND+="quiet" in local.conf will do it for testing) should stop the majority of the text. A full splash-from-bootloader is possible if you have a bootloader that displays the image, and then a silent kernel from there.

Note: AFAICT this will only work if booting using grub or syslinux, not U-Boot or some other embedded bootstrap.

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#5 lore raw
Quoted 24 lines · Gary Thomas
Quoted 23 lines · Andreas Enbacka

Hello,

Thanks a lot for info, I will try with that.

//Andreas

-----Original Message-----
From: Burton, Ross [mailto:[email protected]]
Sent: 23. huhtikuuta 2013 15:09
To: Andreas Enbacka
Cc: [email protected]
Subject: Re: [yocto] Splashscreen using psplash

Quoted 8 lines · Andreas Enbacka

I am creating a custom image based on core-image-sato, with a custom splash screen (using psplash). I have been able to replace the default yocto splashscreen in my image, however, my question is whether it is possible to hide the initial console output text displayed on the screen prior to showing the splashscreen? Currently most of the boot process is completed at the stage when the splash screen is being displayed on screen. This is because the image should be used as part of an embedded device, and the end-user should not see any traces of the underlying linux distro.

Quoted 7 lines
Quoted 4 lines

Passing "quiet" to the kernel (APPEND+="quiet" in local.conf will do it for testing) should stop the majority of the text. A full splash-from-bootloader is possible if you have a bootloader that displays the image, and then a silent kernel from there.

Note: AFAICT this will only work if booting using grub or syslinux, not U-Boot or some other embedded bootstrap.

The trick is to redirect the console output somewhere else. By default it goes to the first tty if I recall correctly but you can send it to a serial port or wherever you want...

Cheers,

Richard