imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
Fabio Estevam
reviewerPATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
From: Fabio Estevam <[email protected]>
Setup CCM_CCOSR register to provide a CKO1 clock frequency of 16.5 MHz.
CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c from the mainline kernel.
mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for this board as well.
--- board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg | 11 +++++++++++ 1 file changed, 11 insertions(+)
board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +11 -0
@@ -172,3 +172,14 @@ DATA 4 0x020e0010 0xF00000CF /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ DATA 4 0x020e0018 0x007F007F DATA 4 0x020e001c 0x007F007F + +/* + * Setup CCM_CCOSR register as follows: + * + * cko1_en = 1 --> CKO1 enabled + * cko1_div = 111 --> divide by 8 + * cko1_sel = 1011 --> ahb_clk_root + * + * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz + */ +DATA 4 0x020c4060 0x000000fb
Signature · 1 line
1.7.9.5
PATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
Thanks Fabio,
Quoted 8 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Setup
CCM_CCOSRregister to provide a CKO1 clock frequency of 16.5 MHz.CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the bootloader will allow us to remove a lot of code in
arch/arm/mach-imx/mach-imx6q.cfrom the mainline kernel.
More importantly than eliminating code in the mainline kernel, enabling the clock will remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers. I believe you can see this under Android by issuing a 'reboot' command.
We've been meaning to push a patch for this for a while.
We did it in two parts.
1.) Add routine to enable the clock:
https://github.com/boundarydevices/u-boot-imx6/commit/7087d645ea1ad476825ea96a1b6f3747f5980028
2.) Enable it on each of SABRE Lite, Nitrogen6X and one of our custom boards.
https://github.com/boundarydevices/u-boot-imx6/commit/44b1015f69b52c0a7d7b930b0607af7a724e29bb
Quoted 3 lines
mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for this board as well.
Does wandboard also use SGTL5000 connected up to CKO1?
Quoted 25 lines
Signed-off-by Fabio Estevam <[email protected]>--- board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg | 11 +++++++++++ 1 file changed, 11 insertions(+)board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +11
-0@@ -172,3 +172,14 @@ DATA 4 0x020e0010 0xF00000CF /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ DATA 4 0x020e0018 0x007F007F DATA 4 0x020e001c 0x007F007F + +/* + * Setup CCM_CCOSR register as follows: + * + * cko1_en = 1 --> CKO1 enabled + * cko1_div = 111 --> divide by 8 + * cko1_sel = 1011 --> ahb_clk_root + * + * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz + */ +DATA 4 0x020c4060 0x000000fb
Fabio Estevam
reviewerPATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
Hi Eric,
Quoted 4 lines · Eric Nelson
More importantly than eliminating code in the mainline kernel, enabling the clock will remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers. I believe you can see this under Android by issuing a 'reboot' command.
Ok, great. I was not aware of this problem. Glad to know that it also fixes it.
I can send this same change to nitrogen and wandboard.
Quoted 1 line
Does wandboard also use SGTL5000 connected up to CKO1?
Yes, it does.
I started to adding audio support to wandboard in the mainline kernel, then I saw all the code that mx6qsabrelite uses to configure the cko1, and I preferred not to repeat it again.
It is much simpler to let the bootloader take care of it, as it is a simple register write.
Regards,
Fabio Estevam
PATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
Hi all,
I am working on IMX6Q-SabreLite Board.in that board we have sgtl5000 codec.so I would like to add (sgtl5000) codec support in *u-boot level*.There is no code available in u-boot level for this codec.Can you please help me How to initialize this audio codec and how to test this one in UBOOT level.
It will be very helpful if you send any u-boot level patch for this codec(sgtl5000).
Thanks
Prem.
Quoted 34 lines · Fabio Estevam
Hi Eric,
Quoted 4 lines · Eric Nelson
More importantly than eliminating code in the mainline kernel, enabling the clock will remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers. I believe you can see this under Android by issuing a 'reboot' command.
Ok, great. I was not aware of this problem. Glad to know that it also fixes it.
I can send this same change to nitrogen and wandboard.
Quoted 1 line
Does wandboard also use SGTL5000 connected up to CKO1?
Yes, it does.
I started to adding audio support to wandboard in the mainline kernel, then I saw all the code that mx6qsabrelite uses to configure the cko1, and I preferred not to repeat it again.
It is much simpler to let the bootloader take care of it, as it is a simple register write.
Regards,
Fabio Estevam
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Fabio Estevam
reviewerPATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
Quoted 9 lines · prem s
Hi all,
I am working on IMX6Q-SabreLite Board.in that board we have sgtl5000 codec.so I would like to add (sgtl5000) codec support in u-boot level.There is no code available in u-boot level for this codec.Can you please help me How to initialize this audio codec and how to test this one in UBOOT level.
It will be very helpful if you send any u-boot level patch for this codec(sgtl5000).
I don't have plans to adding audio support into U-boot for imx.
Maybe you could try to use the OBDS code from Freescale, which provides standalone code for setting up various peripherals and then you can use it as a reference for adding audio support in U-boot.
Just curious: what is your requirement in terms of providing the user with an audio response?
Would booting the kernel fast and providing the audio response in the kernel meet your goal?
Regards,
Fabio Estevam
PATCH 1/1 imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR register
In reply to Fabio EstevamQuoted 8 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Setup
CCM_CCOSRregister to provide a CKO1 clock frequency of 16.5 MHz.CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the bootloader will allow us to remove a lot of code in
arch/arm/mach-imx/mach-imx6q.cfrom the mainline kernel.
Quoted 5 lines
mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for this board as well.
Signed-off-by Fabio Estevam <[email protected]>---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================