Skip to contentSkip to conversation

Add initial i.MX6 SoloLite support

PATCH New Shawn Guo 2 participants 8 messages May 3, 2013

Subsystems (7)
lore
Share & tools
lore

Shawn Guo

author
#0 lore raw

cover Add initial i.MX6 SoloLite support

The i.MX6 SoloLite (imx6sl) is another member of Freescale i.MX6 family besides i.MX6 Quad/Dual (imx6q) and i.MX6 DualLite/Solo (imx6dl). Unlike that there are much similarity and compatibility between imx6q and imx6dl, imx6sl has significant differences on the integrated multimedia IP blocks. That's why we choose to add imx6dl support on top of imx6q code base, but imx6sl support is added as a new SoC here.

Shawn Guo (5):
ARM: imx: add clock support for imx6sl
ARM: imx: enable low-level debug support for imx6sl
ARM: imx: add initial support for imx6sl
ARM: dts: add device tree source for imx6sl SoC
ARM: dts: imx6sl: add initial imx6sl-evk support

 .../devicetree/bindings/clock/imx6sl-clock.txt     |   10 +
 arch/arm/Kconfig.debug                             |   13 +-
 arch/arm/boot/dts/Makefile                         |    3 +-
 arch/arm/boot/dts/imx6sl-evk.dts                   |   74 ++
 arch/arm/boot/dts/imx6sl.dtsi                      |  777 ++++++++++++++++++++
 arch/arm/include/debug/imx-uart.h                  |   10 +
 arch/arm/mach-imx/Kconfig                          |   19 +
 arch/arm/mach-imx/Makefile                         |    1 +
 arch/arm/mach-imx/clk-imx6sl.c                     |  270 +++++++
 arch/arm/mach-imx/common.h                         |    1 +
 arch/arm/mach-imx/mach-imx6sl.c                    |   48 ++
 include/dt-bindings/clock/imx6sl-clock.h           |  148 ++++
 12 files changed, 1371 insertions(+), 3 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/imx6sl-clock.txt
 create mode 100644 arch/arm/boot/dts/imx6sl-evk.dts
 create mode 100644 arch/arm/boot/dts/imx6sl.dtsi
 create mode 100644 arch/arm/mach-imx/clk-imx6sl.c
 create mode 100644 arch/arm/mach-imx/mach-imx6sl.c
 create mode 100644 include/dt-bindings/clock/imx6sl-clock.h
Signature · 1 line
1.7.9.5
author
#1 lore raw

PATCH 1/5 ARM: imx: add clock support for imx6sl

Add clock support for i.MX6 SoloLite. It uses the dtc marco support to define all clock IDs in imx6sl-clock.h, which will be included by both clock driver and device tree sources, so that the data will stay sync all the time between kernel and DT.

---
 .../devicetree/bindings/clock/imx6sl-clock.txt     |   10 +
 arch/arm/mach-imx/clk-imx6sl.c                     |  270 ++++++++++++++++++++
 include/dt-bindings/clock/imx6sl-clock.h           |  148 +++++++++++
 3 files changed, 428 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/imx6sl-clock.txt
 create mode 100644 arch/arm/mach-imx/clk-imx6sl.c
 create mode 100644 include/dt-bindings/clock/imx6sl-clock.h
Documentation/devicetree/bindings/clock/imx6sl-clock.txt new file +10 -0
new file mode 100644
index 0000000..15e40bd
@@ -0,0 +1,10 @@
+* Clock bindings for Freescale i.MX6 SoloLite
+
+Required properties:
+- compatible: Should be "fsl,imx6sl-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx6sl-clock.h
+for the full list of i.MX6 SoloLite clock IDs.
arch/arm/mach-imx/clk-imx6sl.c new file +270 -0

270 lines not on this page · raw message

include/dt-bindings/clock/imx6sl-clock.h new file +148 -0

148 lines not on this page · raw message

Signature · 1 line
1.7.9.5
author
#2 lore raw

PATCH 2/5 ARM: imx: enable low-level debug support for imx6sl

In reply to Shawn Guo

Enable low-level debug support for i.MX6 SoloLite by adding the debug port definitions for the SoC.

---
 arch/arm/Kconfig.debug            |   13 +++++++++++--
 arch/arm/include/debug/imx-uart.h |   10 ++++++++++
 2 files changed, 21 insertions(+), 2 deletions(-)
arch/arm/Kconfig.debug +11 -2
index 24aeef7..b025103 100644
@@ -240,6 +240,13 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX6Q/DL.
 
+	config DEBUG_IMX6SL_UART
+		bool "i.MX6SL Debug UART"
+		depends on SOC_IMX6SL
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on i.MX6SL.
+
 	config DEBUG_MMP_UART2
 		bool "Kernel low-level debugging message via MMP UART2"
 		depends on ARCH_MMP
@@ -493,7 +500,8 @@ config DEBUG_IMX_UART_PORT
 						DEBUG_IMX35_UART || \
 						DEBUG_IMX51_UART || \
 						DEBUG_IMX53_UART || \
-						DEBUG_IMX6Q_UART
+						DEBUG_IMX6Q_UART || \
+						DEBUG_IMX6SL_UART
 	default 1
 	depends on ARCH_MXC
 	help
@@ -588,7 +596,8 @@ config DEBUG_LL_INCLUDE
 				 DEBUG_IMX35_UART || \
 				 DEBUG_IMX51_UART || \
 				 DEBUG_IMX53_UART ||\
-				 DEBUG_IMX6Q_UART
+				 DEBUG_IMX6Q_UART || \
+				 DEBUG_IMX6SL_UART
 	default "debug/highbank.S" if DEBUG_HIGHBANK_UART
 	default "debug/mvebu.S" if DEBUG_MVEBU_UART
 	default "debug/mxs.S" if DEBUG_IMX23_UART || DEBUG_IMX28_UART
arch/arm/include/debug/imx-uart.h +10 -0
index 91d38e3..29da84e 100644
@@ -65,6 +65,14 @@
 #define IMX6Q_UART_BASE_ADDR(n)	IMX6Q_UART##n##_BASE_ADDR
 #define IMX6Q_UART_BASE(n)	IMX6Q_UART_BASE_ADDR(n)
 
+#define IMX6SL_UART1_BASE_ADDR	0x02020000
+#define IMX6SL_UART2_BASE_ADDR	0x02024000
+#define IMX6SL_UART3_BASE_ADDR	0x02034000
+#define IMX6SL_UART4_BASE_ADDR	0x02038000
+#define IMX6SL_UART5_BASE_ADDR	0x02018000
+#define IMX6SL_UART_BASE_ADDR(n) IMX6SL_UART##n##_BASE_ADDR
+#define IMX6SL_UART_BASE(n)	IMX6SL_UART_BASE_ADDR(n)
+
 #define IMX_DEBUG_UART_BASE(soc) soc##_UART_BASE(CONFIG_DEBUG_IMX_UART_PORT)
 
 #ifdef CONFIG_DEBUG_IMX1_UART
@@ -83,6 +91,8 @@
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX53)
 #elif defined(CONFIG_DEBUG_IMX6Q_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX6Q)
+#elif defined(CONFIG_DEBUG_IMX6SL_UART)
+#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX6SL)
 #endif
 
 #endif /* __DEBUG_IMX_UART_H */
Signature · 1 line
1.7.9.5
author
#3 lore raw

PATCH 3/5 ARM: imx: add initial support for imx6sl

In reply to Shawn Guo

Add initial support for i.MX6 SoloLite.

---
 arch/arm/mach-imx/Kconfig       |   19 ++++++++++++++++
 arch/arm/mach-imx/Makefile      |    1 +
 arch/arm/mach-imx/common.h      |    1 +
 arch/arm/mach-imx/mach-imx6sl.c |   48 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 69 insertions(+)
 create mode 100644 arch/arm/mach-imx/mach-imx6sl.c
arch/arm/mach-imx/Kconfig +19 -0
index c132f6f..8454221 100644
@@ -820,6 +820,25 @@ config SOC_IMX6Q
 	help
 	  This enables support for Freescale i.MX6 Quad processor.
 
+config SOC_IMX6SL
+	bool "i.MX6 SoloLite support"
+	select ARM_ERRATA_754322
+	select ARM_ERRATA_775420
+	select ARM_GIC
+	select CPU_V7
+	select HAVE_IMX_ANATOP
+	select HAVE_IMX_GPC
+	select HAVE_IMX_MMDC
+	select HAVE_IMX_SRC
+	select PINCTRL
+	select PINCTRL_IMX6SL
+	select PL310_ERRATA_588369 if CACHE_PL310
+	select PL310_ERRATA_727915 if CACHE_PL310
+	select PL310_ERRATA_769419 if CACHE_PL310
+
+	help
+	  This enables support for Freescale i.MX6 SoloLite processor.
+
 endif
 
 source "arch/arm/mach-imx/devices/Kconfig"
arch/arm/mach-imx/Makefile +1 -0
index b16eb39..d6f99e1 100644
@@ -99,6 +99,7 @@ AFLAGS_headsmp.o :=-Wa,-march=armv7-a
 obj-$(CONFIG_SMP) += headsmp.o platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
 obj-$(CONFIG_SOC_IMX6Q) += clk-imx6q.o mach-imx6q.o
+obj-$(CONFIG_SOC_IMX6SL) += clk-imx6sl.o mach-imx6sl.o
 
 ifeq ($(CONFIG_PM),y)
 obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
arch/arm/mach-imx/common.h +1 -0
index 4cba7db..efae60c 100644
@@ -68,6 +68,7 @@ extern int mx31_clocks_init_dt(void);
 extern int mx51_clocks_init_dt(void);
 extern int mx53_clocks_init_dt(void);
 extern int mx6q_clocks_init(void);
+extern int imx6sl_clocks_init(void);
 extern struct platform_device *mxc_register_gpio(char *name, int id,
 	resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
 extern void mxc_set_cpu_type(unsigned int type);
arch/arm/mach-imx/mach-imx6sl.c new file +48 -0

48 lines not on this page · raw message

Signature · 1 line
1.7.9.5
author
#4 lore raw

PATCH 4/5 ARM: dts: add device tree source for imx6sl SoC

In reply to Shawn Guo

Add SoC level device tree source for imx6sl.

---
 arch/arm/boot/dts/imx6sl.dtsi |  777 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 777 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6sl.dtsi
arch/arm/boot/dts/imx6sl.dtsi new file +777 -0
new file mode 100644
index 0000000..ab506e6
@@ -0,0 +1,777 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include "skeleton.dtsi"
+#include "imx6sl-pinfunc.h"
+#include <dt-bindings/clock/imx6sl-clock.h>
+
+/ {
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	intc: interrupt-controller at 00a01000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-controller;
+		reg = <0x00a01000 0x1000>,
+		      <0x00a00100 0x100>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ckil {
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		osc {
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		L2: l2-cache at 00a02000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x00a02000 0x1000>;
+			interrupts = <0 92 0x04>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <0 94 0x04>;
+		};
+
+		aips1: aips-bus at 02000000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x02000000 0x100000>;
+			ranges;
+
+			spba: spba-bus at 02000000 {
+				compatible = "fsl,spba-bus", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0x02000000 0x40000>;
+				ranges;
+
+				spdif: spdif at 02004000 {
+					reg = <0x02004000 0x4000>;
+					interrupts = <0 52 0x04>;
+				};
+
+				ecspi1: ecspi at 02008000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02008000 0x4000>;
+					interrupts = <0 31 0x04>;
+					clocks = <&clks IMX6SL_CLK_ECSPI1>,
+						 <&clks IMX6SL_CLK_ECSPI1>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi2: ecspi at 0200c000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi";
+					reg = <0x0200c000 0x4000>;
+					interrupts = <0 32 0x04>;
+					clocks = <&clks IMX6SL_CLK_ECSPI2>,
+						 <&clks IMX6SL_CLK_ECSPI2>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi3: ecspi at 02010000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02010000 0x4000>;
+					interrupts = <0 33 0x04>;
+					clocks = <&clks IMX6SL_CLK_ECSPI3>,
+						 <&clks IMX6SL_CLK_ECSPI3>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi4: ecspi at 02014000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02014000 0x4000>;
+					interrupts = <0 34 0x04>;
+					clocks = <&clks IMX6SL_CLK_ECSPI4>,
+						 <&clks IMX6SL_CLK_ECSPI4>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart5: serial at 02018000 {
+					compatible = "fsl,imx6sl-uart", "fsl,imx21-uart";
+					reg = <0x02018000 0x4000>;
+					interrupts = <0 30 0x04>;
+					clocks = <&clks IMX6SL_CLK_UART>,
+						 <&clks IMX6SL_CLK_UART_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart1: serial at 02020000 {
+					compatible = "fsl,imx6sl-uart", "fsl,imx21-uart";
+					reg = <0x02020000 0x4000>;
+					interrupts = <0 26 0x04>;
+					clocks = <&clks IMX6SL_CLK_UART>,
+						 <&clks IMX6SL_CLK_UART_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart2: serial at 02024000 {
+					compatible = "fsl,imx6sl-uart", "fsl,imx21-uart";
+					reg = <0x02024000 0x4000>;
+					interrupts = <0 27 0x04>;
+					clocks = <&clks IMX6SL_CLK_UART>,
+						 <&clks IMX6SL_CLK_UART_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ssi1: ssi at 02028000 {
+					compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi";
+					reg = <0x02028000 0x4000>;
+					interrupts = <0 46 0x04>;
+					clocks = <&clks IMX6SL_CLK_SSI1>;
+					fsl,fifo-depth = <15>;
+					status = "disabled";
+				};
+
+				ssi2: ssi at 0202c000 {
+					compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi";
+					reg = <0x0202c000 0x4000>;
+					interrupts = <0 47 0x04>;
+					clocks = <&clks IMX6SL_CLK_SSI2>;
+					fsl,fifo-depth = <15>;
+					status = "disabled";
+				};
+
+				ssi3: ssi at 02030000 {
+					compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi";
+					reg = <0x02030000 0x4000>;
+					interrupts = <0 48 0x04>;
+					clocks = <&clks IMX6SL_CLK_SSI3>;
+					fsl,fifo-depth = <15>;
+					status = "disabled";
+				};
+
+				uart3: serial at 02034000 {
+					compatible = "fsl,imx6sl-uart", "fsl,imx21-uart";
+					reg = <0x02034000 0x4000>;
+					interrupts = <0 28 0x04>;
+					clocks = <&clks IMX6SL_CLK_UART>,
+						 <&clks IMX6SL_CLK_UART_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart4: serial at 02038000 {
+					compatible = "fsl,imx6sl-uart", "fsl,imx21-uart";
+					reg = <0x02038000 0x4000>;
+					interrupts = <0 29 0x04>;
+					clocks = <&clks IMX6SL_CLK_UART>,
+						 <&clks IMX6SL_CLK_UART_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+			};
+
+			pwm1: pwm at 02080000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
+				reg = <0x02080000 0x4000>;
+				interrupts = <0 83 0x04>;
+				clocks = <&clks IMX6SL_CLK_PWM1>,
+					 <&clks IMX6SL_CLK_PWM1>;
+				clock-names = "ipg", "per";
+			};
+
+			pwm2: pwm at 02084000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
+				reg = <0x02084000 0x4000>;
+				interrupts = <0 84 0x04>;
+				clocks = <&clks IMX6SL_CLK_PWM2>,
+					 <&clks IMX6SL_CLK_PWM2>;
+				clock-names = "ipg", "per";
+			};
+
+			pwm3: pwm at 02088000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
+				reg = <0x02088000 0x4000>;
+				interrupts = <0 85 0x04>;
+				clocks = <&clks IMX6SL_CLK_PWM3>,
+					 <&clks IMX6SL_CLK_PWM3>;
+				clock-names = "ipg", "per";
+			};
+
+			pwm4: pwm at 0208c000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
+				reg = <0x0208c000 0x4000>;
+				interrupts = <0 86 0x04>;
+				clocks = <&clks IMX6SL_CLK_PWM4>,
+					 <&clks IMX6SL_CLK_PWM4>;
+				clock-names = "ipg", "per";
+			};
+
+			gpt: gpt at 02098000 {
+				compatible = "fsl,imx6sl-gpt";
+				reg = <0x02098000 0x4000>;
+				interrupts = <0 55 0x04>;
+				clocks = <&clks IMX6SL_CLK_GPT>,
+					 <&clks IMX6SL_CLK_GPT_SERIAL>;
+				clock-names = "ipg", "per";
+			};
+
+			gpio1: gpio at 0209c000 {
+				compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio";
+				reg = <0x0209c000 0x4000>;
+				interrupts = <0 66 0x04 0 67 0x04>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio2: gpio at 020a0000 {
+				compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio";
+				reg = <0x020a0000 0x4000>;
+				interrupts = <0 68 0x04 0 69 0x04>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio3: gpio at 020a4000 {
+				compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio";
+				reg = <0x020a4000 0x4000>;
+				interrupts = <0 70 0x04 0 71 0x04>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio4: gpio at 020a8000 {
+				compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio";
+				reg = <0x020a8000 0x4000>;
+				interrupts = <0 72 0x04 0 73 0x04>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio5: gpio at 020ac000 {
+				compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio";
+				reg = <0x020ac000 0x4000>;
+				interrupts = <0 74 0x04 0 75 0x04>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			kpp: kpp at 020b8000 {
+				reg = <0x020b8000 0x4000>;
+				interrupts = <0 82 0x04>;
+			};
+
+			wdog1: wdog at 020bc000 {
+				compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt";
+				reg = <0x020bc000 0x4000>;
+				interrupts = <0 80 0x04>;
+				clocks = <&clks IMX6SL_CLK_DUMMY>;
+			};
+
+			wdog2: wdog at 020c0000 {
+				compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt";
+				reg = <0x020c0000 0x4000>;
+				interrupts = <0 81 0x04>;
+				clocks = <&clks IMX6SL_CLK_DUMMY>;
+				status = "disabled";
+			};
+
+			clks: ccm at 020c4000 {
+				compatible = "fsl,imx6sl-ccm";
+				reg = <0x020c4000 0x4000>;
+				interrupts = <0 87 0x04 0 88 0x04>;
+				#clock-cells = <1>;
+			};
+
+			anatop: anatop at 020c8000 {
+				compatible = "fsl,imx6sl-anatop", "syscon", "simple-bus";
+				reg = <0x020c8000 0x1000>;
+				interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
+
+				regulator-1p1 at 110 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd1p1";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1375000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x110>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <4>;
+					anatop-min-voltage = <800000>;
+					anatop-max-voltage = <1375000>;
+				};
+
+				regulator-3p0 at 120 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd3p0";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <3150000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x120>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <0>;
+					anatop-min-voltage = <2625000>;
+					anatop-max-voltage = <3400000>;
+				};
+
+				regulator-2p5 at 130 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd2p5";
+					regulator-min-microvolt = <2100000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x130>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <0>;
+					anatop-min-voltage = <2100000>;
+					anatop-max-voltage = <2850000>;
+				};
+
+				reg_arm: regulator-vddcore at 140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "cpu";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <0>;
+					anatop-vol-bit-width = <5>;
+					anatop-delay-reg-offset = <0x170>;
+					anatop-delay-bit-shift = <24>;
+					anatop-delay-bit-width = <2>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+
+				reg_pu: regulator-vddpu at 140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vddpu";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <9>;
+					anatop-vol-bit-width = <5>;
+					anatop-delay-reg-offset = <0x170>;
+					anatop-delay-bit-shift = <26>;
+					anatop-delay-bit-width = <2>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+
+				reg_soc: regulator-vddsoc at 140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vddsoc";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <18>;
+					anatop-vol-bit-width = <5>;
+					anatop-delay-reg-offset = <0x170>;
+					anatop-delay-bit-shift = <28>;
+					anatop-delay-bit-width = <2>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+			};
+
+			usbphy1: usbphy at 020c9000 {
+				compatible = "fsl,imx6sl-usbphy", "fsl,imx23-usbphy";
+				reg = <0x020c9000 0x1000>;
+				interrupts = <0 44 0x04>;
+				clocks = <&clks IMX6SL_CLK_USBPHY1>;
+			};
+
+			usbphy2: usbphy at 020ca000 {
+				compatible = "fsl,imx6sl-usbphy", "fsl,imx23-usbphy";
+				reg = <0x020ca000 0x1000>;
+				interrupts = <0 45 0x04>;
+				clocks = <&clks IMX6SL_CLK_USBPHY2>;
+			};
+
+			snvs at 020cc000 {
+				compatible = "fsl,sec-v4.0-mon", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x020cc000 0x4000>;
+
+				snvs-rtc-lp at 34 {
+					compatible = "fsl,sec-v4.0-mon-rtc-lp";
+					reg = <0x34 0x58>;
+					interrupts = <0 19 0x04 0 20 0x04>;
+				};
+			};
+
+			epit1: epit at 020d0000 {
+				reg = <0x020d0000 0x4000>;
+				interrupts = <0 56 0x04>;
+			};
+
+			epit2: epit at 020d4000 {
+				reg = <0x020d4000 0x4000>;
+				interrupts = <0 57 0x04>;
+			};
+
+			src: src at 020d8000 {
+				compatible = "fsl,imx6sl-src", "fsl,imx51-src";
+				reg = <0x020d8000 0x4000>;
+				interrupts = <0 91 0x04 0 96 0x04>;
+				#reset-cells = <1>;
+			};
+
+			gpc: gpc at 020dc000 {
+				compatible = "fsl,imx6sl-gpc", "fsl,imx6q-gpc";
+				reg = <0x020dc000 0x4000>;
+				interrupts = <0 89 0x04>;
+			};
+
+			iomuxc: iomuxc at 020e0000 {
+				compatible = "fsl,imx6sl-iomuxc";
+				reg = <0x020e0000 0x4000>;
+
+				fec {
+					pinctrl_fec_1: fecgrp-1 {
+						fsl,pins = <
+							MX6SL_PAD_FEC_MDC__FEC_MDC         0x1b0b0
+							MX6SL_PAD_FEC_MDIO__FEC_MDIO       0x1b0b0
+							MX6SL_PAD_FEC_CRS_DV__FEC_RX_DV    0x1b0b0
+							MX6SL_PAD_FEC_RXD0__FEC_RX_DATA0   0x1b0b0
+							MX6SL_PAD_FEC_RXD1__FEC_RX_DATA1   0x1b0b0
+							MX6SL_PAD_FEC_TX_EN__FEC_TX_EN     0x1b0b0
+							MX6SL_PAD_FEC_TXD0__FEC_TX_DATA0   0x1b0b0
+							MX6SL_PAD_FEC_TXD1__FEC_TX_DATA1   0x1b0b0
+							MX6SL_PAD_FEC_REF_CLK__FEC_REF_OUT 0x4001b0a8
+						>;
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1_1: uart1grp-1 {
+						fsl,pins = <
+							MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+							MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+						>;
+					};
+				};
+
+				usdhc1 {
+					pinctrl_usdhc1_1: usdhc1grp-1 {
+						fsl,pins = <
+							MX6SL_PAD_SD1_CMD__SD1_CMD    0x17059
+							MX6SL_PAD_SD1_CLK__SD1_CLK    0x10059
+							MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+							MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+							MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+							MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+							MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x17059
+							MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x17059
+							MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x17059
+							MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x17059
+						>;
+					};
+				};
+
+				usdhc2 {
+					pinctrl_usdhc2_1: usdhc2grp-1 {
+						fsl,pins = <
+							MX6SL_PAD_SD2_CMD__SD2_CMD    0x17059
+							MX6SL_PAD_SD2_CLK__SD2_CLK    0x10059
+							MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+							MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+							MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+							MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+						>;
+					};
+				};
+
+				usdhc3 {
+					pinctrl_usdhc3_1: usdhc3grp-1 {
+						fsl,pins = <
+							MX6SL_PAD_SD3_CMD__SD3_CMD    0x17059
+							MX6SL_PAD_SD3_CLK__SD3_CLK    0x10059
+							MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+							MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+							MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+							MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+						>;
+					};
+				};
+			};
+
+			csi: csi at 020e4000 {
+				reg = <0x020e4000 0x4000>;
+				interrupts = <0 7 0x04>;
+			};
+
+			spdc: spdc at 020e8000 {
+				reg = <0x020e8000 0x4000>;
+				interrupts = <0 6 0x04>;
+			};
+
+			sdma: sdma at 020ec000 {
+				compatible = "fsl,imx6sl-sdma", "fsl,imx35-sdma";
+				reg = <0x020ec000 0x4000>;
+				interrupts = <0 2 0x04>;
+				clocks = <&clks IMX6SL_CLK_SDMA>,
+					 <&clks IMX6SL_CLK_SDMA>;
+				clock-names = "ipg", "ahb";
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6sl.bin";
+			};
+
+			pxp: pxp at 020f0000 {
+				reg = <0x020f0000 0x4000>;
+				interrupts = <0 98 0x04>;
+			};
+
+			epdc: epdc at 020f4000 {
+				reg = <0x020f4000 0x4000>;
+				interrupts = <0 97 0x04>;
+			};
+
+			lcdif: lcdif at 020f8000 {
+				reg = <0x020f8000 0x4000>;
+				interrupts = <0 39 0x04>;
+			};
+
+			dcp: dcp at 020fc000 {
+				reg = <0x020fc000 0x4000>;
+				interrupts = <0 99 0x04>;
+			};
+		};
+
+		aips2: aips-bus at 02100000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x02100000 0x100000>;
+			ranges;
+
+			usbotg1: usb at 02184000 {
+				compatible = "fsl,imx6sl-usb", "fsl,imx27-usb";
+				reg = <0x02184000 0x200>;
+				interrupts = <0 43 0x04>;
+				clocks = <&clks IMX6SL_CLK_USBOH3>;
+				fsl,usbphy = <&usbphy1>;
+				fsl,usbmisc = <&usbmisc 0>;
+				status = "disabled";
+			};
+
+			usbotg2: usb at 02184200 {
+				compatible = "fsl,imx6sl-usb", "fsl,imx27-usb";
+				reg = <0x02184200 0x200>;
+				interrupts = <0 40 0x04>;
+				clocks = <&clks IMX6SL_CLK_USBOH3>;
+				fsl,usbphy = <&usbphy2>;
+				fsl,usbmisc = <&usbmisc 1>;
+				status = "disabled";
+			};
+
+			usbh: usb at 02184400 {
+				compatible = "fsl,imx6sl-usb", "fsl,imx27-usb";
+				reg = <0x02184400 0x200>;
+				interrupts = <0 42 0x04>;
+				clocks = <&clks IMX6SL_CLK_USBOH3>;
+				fsl,usbmisc = <&usbmisc 2>;
+				status = "disabled";
+			};
+
+			usbmisc: usbmisc at 02184800 {
+				#index-cells = <1>;
+				compatible = "fsl,imx6sl-usbmisc", "fsl,imx6q-usbmisc";
+				reg = <0x02184800 0x200>;
+				clocks = <&clks IMX6SL_CLK_USBOH3>;
+			};
+
+			fec: ethernet at 02188000 {
+				compatible = "fsl,imx6sl-fec", "fsl,imx25-fec";
+				reg = <0x02188000 0x4000>;
+				interrupts = <0 114 0x04>;
+				clocks = <&clks IMX6SL_CLK_ENET_REF>,
+					 <&clks IMX6SL_CLK_ENET_REF>;
+				clock-names = "ipg", "ahb";
+				status = "disabled";
+			};
+
+			usdhc1: usdhc at 02190000 {
+				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				reg = <0x02190000 0x4000>;
+				interrupts = <0 22 0x04>;
+				clocks = <&clks IMX6SL_CLK_USDHC1>,
+					 <&clks IMX6SL_CLK_USDHC1>,
+					 <&clks IMX6SL_CLK_USDHC1>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: usdhc at 02194000 {
+				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				reg = <0x02194000 0x4000>;
+				interrupts = <0 23 0x04>;
+				clocks = <&clks IMX6SL_CLK_USDHC2>,
+					 <&clks IMX6SL_CLK_USDHC2>,
+					 <&clks IMX6SL_CLK_USDHC2>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc3: usdhc at 02198000 {
+				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				reg = <0x02198000 0x4000>;
+				interrupts = <0 24 0x04>;
+				clocks = <&clks IMX6SL_CLK_USDHC3>,
+					 <&clks IMX6SL_CLK_USDHC3>,
+					 <&clks IMX6SL_CLK_USDHC3>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc4: usdhc at 0219c000 {
+				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				reg = <0x0219c000 0x4000>;
+				interrupts = <0 25 0x04>;
+				clocks = <&clks IMX6SL_CLK_USDHC4>,
+					 <&clks IMX6SL_CLK_USDHC4>,
+					 <&clks IMX6SL_CLK_USDHC4>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			i2c1: i2c at 021a0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c";
+				reg = <0x021a0000 0x4000>;
+				interrupts = <0 36 0x04>;
+				clocks = <&clks IMX6SL_CLK_I2C1>;
+				status = "disabled";
+			};
+
+			i2c2: i2c at 021a4000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c";
+				reg = <0x021a4000 0x4000>;
+				interrupts = <0 37 0x04>;
+				clocks = <&clks IMX6SL_CLK_I2C2>;
+				status = "disabled";
+			};
+
+			i2c3: i2c at 021a8000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c";
+				reg = <0x021a8000 0x4000>;
+				interrupts = <0 38 0x04>;
+				clocks = <&clks IMX6SL_CLK_I2C3>;
+				status = "disabled";
+			};
+
+			mmdc: mmdc at 021b0000 {
+				compatible = "fsl,imx6sl-mmdc", "fsl,imx6q-mmdc";
+				reg = <0x021b0000 0x4000>;
+			};
+
+			rngb: rngb at 021b4000 {
+				reg = <0x021b4000 0x4000>;
+				interrupts = <0 5 0x04>;
+			};
+
+			weim: weim at 021b8000 {
+				reg = <0x021b8000 0x4000>;
+				interrupts = <0 14 0x04>;
+			};
+
+			ocotp: ocotp at 021bc000 {
+				compatible = "fsl,imx6sl-ocotp";
+				reg = <0x021bc000 0x4000>;
+			};
+
+			audmux: audmux at 021d8000 {
+				compatible = "fsl,imx6sl-audmux", "fsl,imx31-audmux";
+				reg = <0x021d8000 0x4000>;
+				status = "disabled";
+			};
+		};
+	};
+};
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH 4/5 ARM: dts: add device tree source for imx6sl SoC

arch/arm/boot/dts/imx6sl.dtsi

Quoted 10 lines · Shawn Guo

Add SoC level device tree source for imx6sl.

---
  arch/arm/boot/dts/imx6sl.dtsi |  777 +++++++++++++++++++++++++++++++++++++++++
  1 file changed, 777 insertions(+)

create mode 100644 arch/arm/boot/dts/imx6sl.dtsi

arch/arm/boot/dts/imx6sl.dtsi new file +0 -0
new file mode 100644

Just as a proposal do discuss: What's about to move the existing imx6qdl.dtsi to a imx6.dtsi and include it in

imx6q.dtsi
imx6dl.dtsi
imx6sl.dtsi

then?

Quoted 4 lines
arch/arm/boot/dts/imx6sl.dtsi new file +4 -0
+       soc {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "simple-bus";

arch/arm/boot/dts/imx6sl.dtsi line 78

Quoted 10 lines
arch/arm/boot/dts/imx6sl.dtsi new file +10 -0
+               interrupt-parent = <&intc>;
+               ranges;
+
+               L2: l2-cache at 00a02000 {
+                       compatible = "arm,pl310-cache";
+                       reg = <0x00a02000 0x1000>;
+                       interrupts = <0 92 0x04>;
+                       cache-unified;
+                       cache-level = <2>;
+               };

The arm,tag-latency and arm,data-latency we recently added for the other SoCs are missing here?

Best regards

Dirk

author
#6 lore raw

PATCH 4/5 ARM: dts: add device tree source for imx6sl SoC

Quoted 15 lines · Dirk Behme

arch/arm/boot/dts/imx6sl.dtsi

Quoted 10 lines · Shawn Guo

Add SoC level device tree source for imx6sl.

---
 arch/arm/boot/dts/imx6sl.dtsi |  777 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 777 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6sl.dtsi
arch/arm/boot/dts/imx6sl.dtsi new file +0 -0
new file mode 100644

Just as a proposal do discuss: What's about to move the existing imx6qdl.dtsi to a imx6.dtsi and include it in

Quoted 4 lines

imx6q.dtsi
imx6dl.dtsi
imx6sl.dtsi

No. Doing that would mean we need to do another around of shuffling of all imx6 dts files with one more common level added. And it brings even more churn than last time when we add imx6dl support, since we have more stuff to move around for getting 3 common levels. Comparing imx6qdl.dtsi and imx6sl.dtsi, you will find that the effort is not really worthy, because there are already enough differences there.

Quoted 16 lines

then?

Quoted 4 lines
arch/arm/boot/dts/imx6sl.dtsi new file +4 -0
+       soc {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "simple-bus";

arch/arm/boot/dts/imx6sl.dtsi line 78

Quoted 10 lines
arch/arm/boot/dts/imx6sl.dtsi new file +10 -0
+               interrupt-parent = <&intc>;
+               ranges;
+
+               L2: l2-cache at 00a02000 {
+                       compatible = "arm,pl310-cache";
+                       reg = <0x00a02000 0x1000>;
+                       interrupts = <0 92 0x04>;
+                       cache-unified;
+                       cache-level = <2>;
+               };
Quoted 2 lines

The arm,tag-latency and arm,data-latency we recently added for the other SoCs are missing here?

Right, I will add it.

Shawn

author
#7 lore raw

PATCH 5/5 ARM: dts: imx6sl: add initial imx6sl-evk support

In reply to Shawn Guo

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.

---
 arch/arm/boot/dts/Makefile       |    3 +-
 arch/arm/boot/dts/imx6sl-evk.dts |   74 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 76 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/imx6sl-evk.dts
arch/arm/boot/dts/Makefile +2 -1
index 2498cba..73794c3 100644
@@ -106,7 +106,8 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-sabreauto.dtb \
 	imx6q-sabrelite.dtb \
 	imx6q-sabresd.dtb \
-	imx6q-sbc6x.dtb
+	imx6q-sbc6x.dtb \
+	imx6sl-evk.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx23-olinuxino.dtb \
 	imx23-stmp378x_devb.dtb \
arch/arm/boot/dts/imx6sl-evk.dts new file +74 -0

74 lines not on this page · raw message

Signature · 1 line
1.7.9.5