Skip to contentSkip to conversation

ide: Test cases and a corner case fix

PATCH In review Kevin Wolf 3 participants 8 messages May 8, 2013

lore
Share & tools
lore

Kevin Wolf

author
#0 lore raw

cover ide: Test cases and a corner case fix

Kevin Wolf (5):
ide: Reset BMIDEA bit when the bus master is stopped libqos/pci: Enable bus mastering
qtest: Add IDE test case
qtest/ide-test: Add simple DMA read/write test case qtest/ide-test: Test short and long PRDTs

 hw/ide/pci.c       |   1 +
 tests/Makefile     |   2 +
 tests/ide-test.c   | 440 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 tests/libqos/pci.c |   2 +-
 4 files changed, 444 insertions(+), 1 deletion(-)
 create mode 100644 tests/ide-test.c
Signature · 1 line
1.8.1.4
author
#1 lore raw

PATCH 1/5 ide: Reset BMIDEA bit when the bus master is stopped

The device is supposed to reset the Bus Master IDE Active bit in the status register when 0 is written to the Start/Stop Bus Master bit in the command register.

In the common cases this happens automatically because bdrv_drain_all() flushes the requests, but with a large PRDT it could remain set.

---
 hw/ide/pci.c | 1 +
 1 file changed, 1 insertion(+)
hw/ide/pci.c +1 -0
index a310975..635a364 100644
@@ -312,6 +312,7 @@ void bmdma_cmd_writeb(BMDMAState *bm, uint32_t val)
                 bdrv_drain_all();
                 assert(bm->bus->dma->aiocb == NULL);
             }
+            bm->status &= ~BM_STATUS_DMAING;
         } else {
             bm->cur_addr = bm->addr;
             if (!(bm->status & BM_STATUS_DMAING)) {
Signature · 1 line
1.8.1.4
Reviewed-by on v1 1/5
#2 lore raw

Re: [Qemu-devel] [PATCH 1/5] ide: Reset BMIDEA bit when the bus master is stopped

Quoted 11 lines · Kevin Wolf

The device is supposed to reset the Bus Master IDE Active bit in the status register when 0 is written to the Start/Stop Bus Master bit in the command register.

In the common cases this happens automatically because bdrv_drain_all() flushes the requests, but with a large PRDT it could remain set.

---
 hw/ide/pci.c | 1 +
 1 file changed, 1 insertion(+)
author
#3 lore raw

PATCH 2/5 libqos/pci: Enable bus mastering

In reply to Kevin Wolf
---
 tests/libqos/pci.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tests/libqos/pci.c +1 -1
index 95e287b..7e0907b 100644
@@ -71,7 +71,7 @@ void qpci_device_enable(QPCIDevice *dev)
 
     /* FIXME -- does this need to be a bus callout? */
     cmd = qpci_config_readw(dev, PCI_COMMAND);
-    cmd |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY;
+    cmd |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
     qpci_config_writew(dev, PCI_COMMAND, cmd);
 }
 
Signature · 1 line
1.8.1.4
author
#4 lore raw

PATCH 3/5 qtest: Add IDE test case

In reply to Kevin Wolf

This adds a simple IDE test case and starts by verifying that IDENTIFY can be successfully used and return the correct serial number, version and the WCE flag is set for cache=writeback.

---
 tests/Makefile   |   2 +
 tests/ide-test.c | 165 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 167 insertions(+)
 create mode 100644 tests/ide-test.c
tests/Makefile +2 -0
index bf41d10..a307d5a 100644
@@ -51,6 +51,7 @@ check-block-$(CONFIG_POSIX) += tests/qemu-iotests-quick.sh
 # really in libqtest, not in the testcases themselves.
 check-qtest-i386-y = tests/fdc-test$(EXESUF)
 gcov-files-i386-y = hw/fdc.c
+check-qtest-i386-y += tests/ide-test$(EXESUF)
 check-qtest-i386-y += tests/hd-geo-test$(EXESUF)
 gcov-files-i386-y += hw/hd-geometry.c
 check-qtest-i386-y += tests/rtc-test$(EXESUF)
@@ -127,6 +128,7 @@ libqos-omap-obj-y = $(libqos-obj-y) tests/libqos/i2c-omap.o
 tests/rtc-test$(EXESUF): tests/rtc-test.o
 tests/m48t59-test$(EXESUF): tests/m48t59-test.o
 tests/fdc-test$(EXESUF): tests/fdc-test.o
+tests/ide-test$(EXESUF): tests/ide-test.o $(libqos-pc-obj-y)
 tests/hd-geo-test$(EXESUF): tests/hd-geo-test.o
 tests/tmp105-test$(EXESUF): tests/tmp105-test.o $(libqos-omap-obj-y)
 tests/i440fx-test$(EXESUF): tests/i440fx-test.o $(libqos-pc-obj-y)
tests/ide-test.c new file +165 -0

165 lines not on this page · raw message

Signature · 1 line
1.8.1.4
author
#5 lore raw

PATCH 4/5 qtest/ide-test: Add simple DMA read/write test case

In reply to Kevin Wolf

This tests that single sectors can be successfully written and correctly read back.

---
 tests/ide-test.c | 221 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 221 insertions(+)
tests/ide-test.c +221 -0
index 45036e3..5fc496f 100644
@@ -29,8 +29,12 @@
 #include <glib.h>
 
 #include "libqtest.h"
+#include "libqos/pci-pc.h"
+#include "libqos/malloc-pc.h"
 
 #include "qemu-common.h"
+#include "hw/pci/pci_ids.h"
+#include "hw/pci/pci_regs.h"
 
 #define TEST_IMAGE_SIZE 64 * 1024 * 1024
 
@@ -60,12 +64,42 @@ enum {
 };
 
 enum {
+    LBA     = 0x40,
+};
+
+enum {
+    bmreg_cmd       = 0x0,
+    bmreg_status    = 0x2,
+    bmreg_prdt      = 0x4,
+};
+
+enum {
+    CMD_READ_DMA    = 0xc8,
+    CMD_WRITE_DMA   = 0xca,
     CMD_IDENTIFY    = 0xec,
 };
 
+enum {
+    BM_CMD_START    =  0x1,
+    BM_CMD_WRITE    =  0x8, /* write = from device to memory */
+};
+
+enum {
+    BM_STS_ACTIVE   =  0x1,
+    BM_STS_ERROR    =  0x2,
+    BM_STS_INTR     =  0x4,
+};
+
+enum {
+    PRDT_EOT        = 0x80000000,
+};
+
 #define assert_bit_set(data, mask) g_assert_cmphex((data) & (mask), ==, (mask))
 #define assert_bit_clear(data, mask) g_assert_cmphex((data) & (mask), ==, 0)
 
+static QPCIBus *pcibus = NULL;
+static QGuestAllocator *guest_malloc;
+
 static char tmp_path[] = "/tmp/qtest.XXXXXX";
 
 static void ide_test_start(const char *cmdline_fmt, ...)
@@ -79,6 +113,7 @@ static void ide_test_start(const char *cmdline_fmt, ...)
 
     qtest_start(cmdline);
     qtest_irq_intercept_in(global_qtest, "ioapic");
+    guest_malloc = pc_alloc_init();
 }
 
 static void ide_test_quit(void)
@@ -86,6 +121,188 @@ static void ide_test_quit(void)
     qtest_quit(global_qtest);
 }
 
+static QPCIDevice *get_pci_device(uint16_t *bmdma_base)
+{
+    QPCIDevice *dev;
+    uint16_t vendor_id, device_id;
+
+    if (!pcibus) {
+        pcibus = qpci_init_pc();
+    }
+
+    /* Find PCI device and verify it's the right one */
+    dev = qpci_device_find(pcibus, QPCI_DEVFN(IDE_PCI_DEV, IDE_PCI_FUNC));
+    g_assert(dev != NULL);
+
+    vendor_id = qpci_config_readw(dev, PCI_VENDOR_ID);
+    device_id = qpci_config_readw(dev, PCI_DEVICE_ID);
+    g_assert(vendor_id == PCI_VENDOR_ID_INTEL);
+    g_assert(device_id == PCI_DEVICE_ID_INTEL_82371SB_1);
+
+    /* Map bmdma BAR */
+    *bmdma_base = (uint16_t)(uintptr_t) qpci_iomap(dev, 4);
+
+    qpci_device_enable(dev);
+
+    return dev;
+}
+
+static void free_pci_device(QPCIDevice *dev)
+{
+    /* libqos doesn't have a function for this, so free it manually */
+    g_free(dev);
+}
+
+typedef struct PrdtEntry {
+    uint32_t addr;
+    uint32_t size;
+} QEMU_PACKED PrdtEntry;
+
+#define assert_bit_set(data, mask) g_assert_cmphex((data) & (mask), ==, (mask))
+#define assert_bit_clear(data, mask) g_assert_cmphex((data) & (mask), ==, 0)
+
+static int send_dma_request(int cmd, uint64_t sector, int nb_sectors,
+                            PrdtEntry *prdt, int prdt_entries)
+{
+    QPCIDevice *dev;
+    uint16_t bmdma_base;
+    uintptr_t guest_prdt;
+    size_t len;
+    bool from_dev;
+    uint8_t status;
+
+    dev = get_pci_device(&bmdma_base);
+
+    switch (cmd) {
+    case CMD_READ_DMA:
+        from_dev = true;
+        break;
+    case CMD_WRITE_DMA:
+        from_dev = false;
+        break;
+    default:
+        g_assert_not_reached();
+    }
+
+    /* Select device 0 */
+    outb(IDE_BASE + reg_device, 0 | LBA);
+
+    /* Stop any running transfer, clear any pending interrupt */
+    outb(bmdma_base + bmreg_cmd, 0);
+    outb(bmdma_base + bmreg_status, BM_STS_INTR);
+
+    /* Setup PRDT */
+    len = sizeof(*prdt) * prdt_entries;
+    guest_prdt = guest_alloc(guest_malloc, len);
+    memwrite(guest_prdt, prdt, len);
+    outl(bmdma_base + bmreg_prdt, guest_prdt);
+
+    /* ATA DMA command */
+    outb(IDE_BASE + reg_nsectors, nb_sectors);
+
+    outb(IDE_BASE + reg_lba_low,    sector & 0xff);
+    outb(IDE_BASE + reg_lba_middle, (sector >> 8) & 0xff);
+    outb(IDE_BASE + reg_lba_high,   (sector >> 16) & 0xff);
+
+    outb(IDE_BASE + reg_command, cmd);
+
+    /* Start DMA transfer */
+    outb(bmdma_base + bmreg_cmd, BM_CMD_START | (from_dev ? BM_CMD_WRITE : 0));
+
+    /* Wait for the DMA transfer to complete */
+    do {
+        status = inb(bmdma_base + bmreg_status);
+    } while ((status & (BM_STS_ACTIVE | BM_STS_INTR)) == BM_STS_ACTIVE);
+
+    g_assert_cmpint(get_irq(IDE_PRIMARY_IRQ), ==, !!(status & BM_STS_INTR));
+
+    /* Check IDE status code */
+    assert_bit_set(inb(IDE_BASE + reg_status), DRDY);
+    assert_bit_clear(inb(IDE_BASE + reg_status), BSY | DRQ);
+
+    /* Reading the status register clears the IRQ */
+    g_assert(!get_irq(IDE_PRIMARY_IRQ));
+
+    /* Stop DMA transfer if still active */
+    if (status & BM_STS_ACTIVE) {
+        outb(bmdma_base + bmreg_cmd, 0);
+    }
+
+    free_pci_device(dev);
+
+    return status;
+}
+
+static void test_bmdma_simple_rw(void)
+{
+    uint8_t status;
+    uint8_t *buf;
+    uint8_t *cmpbuf;
+    size_t len = 512;
+    uintptr_t guest_buf = guest_alloc(guest_malloc, len);
+
+    PrdtEntry prdt[] = {
+        { .addr = guest_buf, .size = len | PRDT_EOT },
+    };
+
+    buf = g_malloc(len);
+    cmpbuf = g_malloc(len);
+
+    /* Write 0x55 pattern to sector 0 */
+    memset(buf, 0x55, len);
+    memwrite(guest_buf, buf, len);
+
+    status = send_dma_request(CMD_WRITE_DMA, 0, 1, prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    /* Write 0xaa pattern to sector 1 */
+    memset(buf, 0xaa, len);
+    memwrite(guest_buf, buf, len);
+
+    status = send_dma_request(CMD_WRITE_DMA, 1, 1, prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    /* Read and verify 0x55 pattern in sector 0 */
+    memset(cmpbuf, 0x55, len);
+
+    status = send_dma_request(CMD_READ_DMA, 0, 1, prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    memread(guest_buf, buf, len);
+    g_assert(memcmp(buf, cmpbuf, len) == 0);
+
+    /* Read and verify 0xaa pattern in sector 1 */
+    memset(cmpbuf, 0xaa, len);
+
+    status = send_dma_request(CMD_READ_DMA, 1, 1, prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    memread(guest_buf, buf, len);
+    g_assert(memcmp(buf, cmpbuf, len) == 0);
+
+
+    g_free(buf);
+    g_free(cmpbuf);
+}
+
+static void test_bmdma_setup(void)
+{
+    ide_test_start(
+        "-vnc none "
+        "-drive file=%s,if=ide,serial=%s,cache=writeback "
+        "-global ide-hd.ver=%s",
+        tmp_path, "testdisk", "version");
+}
+
+static void test_bmdma_teardown(void)
+{
+    ide_test_quit();
+}
+
 static void test_identify(void)
 {
     uint8_t data;
@@ -156,6 +373,10 @@ int main(int argc, char **argv)
 
     qtest_add_func("/ide/identify", test_identify);
 
+    qtest_add_func("/ide/bmdma/setup", test_bmdma_setup);
+    qtest_add_func("/ide/bmdma/simple_rw", test_bmdma_simple_rw);
+    qtest_add_func("/ide/bmdma/teardown", test_bmdma_teardown);
+
     ret = g_test_run();
 
     /* Cleanup */
Signature · 1 line
1.8.1.4
#6 lore raw

Re: [Qemu-devel] [PATCH 4/5] qtest/ide-test: Add simple DMA read/write test case

Il 08/05/2013 11:43, Kevin Wolf ha scritto:

Quoted 144 lines

This tests that single sectors can be successfully written and correctly read back.

---
 tests/ide-test.c | 221 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 221 insertions(+)
tests/ide-test.c +99 -0
index 45036e3..5fc496f 100644
@@ -29,8 +29,12 @@
 #include <glib.h>
 
 #include "libqtest.h"
+#include "libqos/pci-pc.h"
+#include "libqos/malloc-pc.h"
 
 #include "qemu-common.h"
+#include "hw/pci/pci_ids.h"
+#include "hw/pci/pci_regs.h"
 
 #define TEST_IMAGE_SIZE 64 * 1024 * 1024
 
@@ -60,12 +64,42 @@ enum {
 };
 
 enum {
+    LBA     = 0x40,
+};
+
+enum {
+    bmreg_cmd       = 0x0,
+    bmreg_status    = 0x2,
+    bmreg_prdt      = 0x4,
+};
+
+enum {
+    CMD_READ_DMA    = 0xc8,
+    CMD_WRITE_DMA   = 0xca,
     CMD_IDENTIFY    = 0xec,
 };
 
+enum {
+    BM_CMD_START    =  0x1,
+    BM_CMD_WRITE    =  0x8, /* write = from device to memory */
+};
+
+enum {
+    BM_STS_ACTIVE   =  0x1,
+    BM_STS_ERROR    =  0x2,
+    BM_STS_INTR     =  0x4,
+};
+
+enum {
+    PRDT_EOT        = 0x80000000,
+};
+
 #define assert_bit_set(data, mask) g_assert_cmphex((data) & (mask), ==, (mask))
 #define assert_bit_clear(data, mask) g_assert_cmphex((data) & (mask), ==, 0)
 
+static QPCIBus *pcibus = NULL;
+static QGuestAllocator *guest_malloc;
+
 static char tmp_path[] = "/tmp/qtest.XXXXXX";
 
 static void ide_test_start(const char *cmdline_fmt, ...)
@@ -79,6 +113,7 @@ static void ide_test_start(const char *cmdline_fmt, ...)
 
     qtest_start(cmdline);
     qtest_irq_intercept_in(global_qtest, "ioapic");
+    guest_malloc = pc_alloc_init();
 }
 
 static void ide_test_quit(void)
@@ -86,6 +121,188 @@ static void ide_test_quit(void)
     qtest_quit(global_qtest);
 }
 
+static QPCIDevice *get_pci_device(uint16_t *bmdma_base)
+{
+    QPCIDevice *dev;
+    uint16_t vendor_id, device_id;
+
+    if (!pcibus) {
+        pcibus = qpci_init_pc();
+    }
+
+    /* Find PCI device and verify it's the right one */
+    dev = qpci_device_find(pcibus, QPCI_DEVFN(IDE_PCI_DEV, IDE_PCI_FUNC));
+    g_assert(dev != NULL);
+
+    vendor_id = qpci_config_readw(dev, PCI_VENDOR_ID);
+    device_id = qpci_config_readw(dev, PCI_DEVICE_ID);
+    g_assert(vendor_id == PCI_VENDOR_ID_INTEL);
+    g_assert(device_id == PCI_DEVICE_ID_INTEL_82371SB_1);
+
+    /* Map bmdma BAR */
+    *bmdma_base = (uint16_t)(uintptr_t) qpci_iomap(dev, 4);
+
+    qpci_device_enable(dev);
+
+    return dev;
+}
+
+static void free_pci_device(QPCIDevice *dev)
+{
+    /* libqos doesn't have a function for this, so free it manually */
+    g_free(dev);
+}
+
+typedef struct PrdtEntry {
+    uint32_t addr;
+    uint32_t size;
+} QEMU_PACKED PrdtEntry;
+
+#define assert_bit_set(data, mask) g_assert_cmphex((data) & (mask), ==, (mask))
+#define assert_bit_clear(data, mask) g_assert_cmphex((data) & (mask), ==, 0)
+
+static int send_dma_request(int cmd, uint64_t sector, int nb_sectors,
+                            PrdtEntry *prdt, int prdt_entries)
+{
+    QPCIDevice *dev;
+    uint16_t bmdma_base;
+    uintptr_t guest_prdt;
+    size_t len;
+    bool from_dev;
+    uint8_t status;
+
+    dev = get_pci_device(&bmdma_base);
+
+    switch (cmd) {
+    case CMD_READ_DMA:
+        from_dev = true;
+        break;
+    case CMD_WRITE_DMA:
+        from_dev = false;
+        break;
+    default:
+        g_assert_not_reached();
+    }
+
+    /* Select device 0 */

tests/ide-test.c static void ide_test_quit(void) · line 197

Quoted 10 lines
tests/ide-test.c +10 -0
+    outb(IDE_BASE + reg_device, 0 | LBA);
+
+    /* Stop any running transfer, clear any pending interrupt */
+    outb(bmdma_base + bmreg_cmd, 0);
+    outb(bmdma_base + bmreg_status, BM_STS_INTR);
+
+    /* Setup PRDT */
+    len = sizeof(*prdt) * prdt_entries;
+    guest_prdt = guest_alloc(guest_malloc, len);
+    memwrite(guest_prdt, prdt, len);

What endianness?

Paolo

Quoted 1 line
tests/ide-test.c +1 -0
+    outl(bmdma_base + bmreg_prdt, guest_prdt);
author
#7 lore raw

PATCH 5/5 qtest/ide-test: Test short and long PRDTs

In reply to Kevin Wolf

This tests the behaviour of the DMA engine when the given PRDT contains physical region descriptors for either more or less bytes than the IDE request is for.

---
 tests/ide-test.c | 54 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)
tests/ide-test.c +54 -0
index 5fc496f..bdc1da7 100644
@@ -77,6 +77,8 @@ enum {
     CMD_READ_DMA    = 0xc8,
     CMD_WRITE_DMA   = 0xca,
     CMD_IDENTIFY    = 0xec,
+
+    CMDF_ABORT      = 0x100,
 };
 
 enum {
@@ -170,9 +172,13 @@ static int send_dma_request(int cmd, uint64_t sector, int nb_sectors,
     size_t len;
     bool from_dev;
     uint8_t status;
+    int flags;
 
     dev = get_pci_device(&bmdma_base);
 
+    flags = cmd & ~0xff;
+    cmd &= 0xff;
+
     switch (cmd) {
     case CMD_READ_DMA:
         from_dev = true;
@@ -209,6 +215,10 @@ static int send_dma_request(int cmd, uint64_t sector, int nb_sectors,
     /* Start DMA transfer */
     outb(bmdma_base + bmreg_cmd, BM_CMD_START | (from_dev ? BM_CMD_WRITE : 0));
 
+    if (flags & CMDF_ABORT) {
+        outb(bmdma_base + bmreg_cmd, 0);
+    }
+
     /* Wait for the DMA transfer to complete */
     do {
         status = inb(bmdma_base + bmreg_status);
@@ -289,6 +299,48 @@ static void test_bmdma_simple_rw(void)
     g_free(cmpbuf);
 }
 
+static void test_bmdma_short_prdt(void)
+{
+    uint8_t status;
+
+    PrdtEntry prdt[] = {
+        { .addr = 0, .size = 0x10 | PRDT_EOT },
+    };
+
+    /* Normal request */
+    status = send_dma_request(CMD_READ_DMA, 0, 1,
+                              prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, 0);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    /* Abort the request before it completes */
+    status = send_dma_request(CMD_READ_DMA | CMDF_ABORT, 0, 1,
+                              prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, 0);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+}
+
+static void test_bmdma_long_prdt(void)
+{
+    uint8_t status;
+
+    PrdtEntry prdt[] = {
+        { .addr = 0, .size = 0x1000 | PRDT_EOT },
+    };
+
+    /* Normal request */
+    status = send_dma_request(CMD_READ_DMA, 0, 1,
+                              prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_ACTIVE | BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+
+    /* Abort the request before it completes */
+    status = send_dma_request(CMD_READ_DMA | CMDF_ABORT, 0, 1,
+                              prdt, ARRAY_SIZE(prdt));
+    g_assert_cmphex(status, ==, BM_STS_INTR);
+    assert_bit_clear(inb(IDE_BASE + reg_status), DF | ERR);
+}
+
 static void test_bmdma_setup(void)
 {
     ide_test_start(
@@ -375,6 +427,8 @@ int main(int argc, char **argv)
 
     qtest_add_func("/ide/bmdma/setup", test_bmdma_setup);
     qtest_add_func("/ide/bmdma/simple_rw", test_bmdma_simple_rw);
+    qtest_add_func("/ide/bmdma/short_prdt", test_bmdma_short_prdt);
+    qtest_add_func("/ide/bmdma/long_prdt", test_bmdma_long_prdt);
     qtest_add_func("/ide/bmdma/teardown", test_bmdma_teardown);
 
     ret = g_test_run();
Signature · 1 line
1.8.1.4