ALSA: hda - Enable runtime pm for Haswell
PATCH 1/1 ALSA: hda - Enable runtime pm for Haswell
Haswell doesnot support runtime pm by default.
This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)
sound/pci/hda/hda_intel.c +6 -0
@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait);
Signature · 1 line
1.7.9.5
At Thu, 16 May 2013 16:29:05 +0800,
Quoted 6 lines · Wang Xingchao
Haswell doesnot support runtime pm by default.
This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.Signed-off-by Wang Xingchao <[email protected]>
I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
Takashi
Quoted 24 lines
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)sound/pci/hda/hda_intel.c +6
-0@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait);Signature · 1 line
1.7.9.5
Hi Takashi,
Quoted 11 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellAt Thu, 16 May 2013 16:29:05 +0800,
Quoted 1 line · Wang Xingchao
Quoted 8 lines
Quoted 5 lines
Haswell doesnot support runtime pm by default.
This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
Haswell doesnot show its power capability to support PME, I'm not sure it's caused by BIOS setting or need some additional configurations in PCI registers.
So pci_dev_run_wake() return false and this make haswell lose
the chance to support runtime pm in software, right?
If a PCI device would support runtime pm in software, maybe it doesnot support PME in hardware level, it should get a chance to try. I see some pci devices, they look much like:
pm_runtime_put_noidle(&pdev->dev);pm_runtime_allow(&pdev->dev);
anyway it's better if we can set haswell PME capability externally, then it fits current code. but if there's such software requirement for runtime pm, it should be improved, right?
Thanks
--xingchao
Quoted 28 lines
Takashi
Quoted 24 lines
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)sound/pci/hda/hda_intel.c +6
-1@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait); --1.7.9.5
Hi,
Add Rafael in loop.
Quoted 11 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellAt Thu, 16 May 2013 16:29:05 +0800,
Quoted 1 line · Wang Xingchao
Quoted 8 lines
Quoted 5 lines
Haswell doesnot support runtime pm by default.
This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
I wonder whether it's HD-A driver's policy to only support runtime PM if the device can support signal wakup? According to Rafael, the device can support runtime PM regardless, no matter it supports PME or not. If so, we should remove the "if" condition check here.
Thanks
--xingchao
Quoted 28 lines
Takashi
Quoted 24 lines
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)sound/pci/hda/hda_intel.c +6
-1@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait); --1.7.9.5
At Wed, 22 May 2013 03:56:00 +0000,
Quoted 20 lines · Xingchao
Hi,
Add Rafael in loop.
Quoted 15 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellAt Thu, 16 May 2013 16:29:05 +0800,
Quoted 5 lines · Wang Xingchao
Haswell doesnot support runtime pm by default.
This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
I wonder whether it's HD-A driver's policy to only support runtime PM if the device can support signal wakup? According to Rafael, the device can support runtime PM regardless, no matter it supports PME or not. If so, we should remove the "if" condition check here.
Well, if the decision is purely a driver issue, then we can get rid of PME check. But in that case, it should be simply like:
azx_probe() {
...
if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME)
pm_runtime_put_noidle(&pci->dev);
...
}azx_remove() {
...
if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME)
pm_runtime_get_noresume(&pci->dev);
...
}AFAIU, calling pm_runtime_allow() enables the runtime PM *forcibly*. Usually this isn't a good thing.
thanks,
Takashi
Quoted 33 lines
Thanks
--xingchaoQuoted 28 lines
Takashi
Quoted 24 lines
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)sound/pci/hda/hda_intel.c +6
-1@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait); --1.7.9.5
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi Rafael,
Quoted 59 lines
-----Original Message-----
From: Wysocki, Rafael J
Sent: Wednesday, May 22, 2013 7:09 PM
To: Takashi Iwai
Cc: Wang, Xingchao; Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellQuoted 24 lines · Takashi Iwai
At Wed, 22 May 2013 03:56:00 +0000,
Quoted 22 lines · Xingchao
Hi,
Add Rafael in loop.
Quoted 10 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellAt Thu, 16 May 2013 16:29:05 +0800,
Wang Xingchao wrote:Quoted 7 lines
Quoted 5 lines
Haswell doesnot support runtime pm by default. This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.
Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
I wonder whether it's HD-A driver's policy to only support runtime PM if the
device can support signal wakup?
Quoted 1 line
Quoted 1 line
According to Rafael, the device can support runtime PM regardless, no
matter it supports PME or not.
Quoted 3 lines
Quoted 1 line
If so, we should remove the "if" condition check here.
Well, if the decision is purely a driver issue, then we can get rid of PME check.
Yes, it is.
Quoted 17 lines
But in that case, it should be simply like:
azx_probe() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_put_noidle(&pci->dev); ... }azx_remove() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_get_noresume(&pci->dev); ... }
Quoted 6 lines
Quoted 3 lines
AFAIU, calling
pm_runtime_allow()enables the runtime PM *forcibly*. Usually this isn't a good thing.That's correct. Moreover, calling both
pm_runtime_allow()*and*pm_runtime_put_noidle()together would be a bug IMO.
It's interesting something maybe wrong in my test:
1. withtout calling pm_runtime_allow(), azx_runteim_idle/suspend() will not be called.
2. another trick is on my Haswell ULT C stepping board, the runtime PM only work after exit from resume:
echo mem > /sys/power/state
if you donot let system enter suspend manually, the runtime pm will not be triggered.
Is there any dependency between runtime pm suspend and normal suspend?
Thanks
--xingchao
Quoted 30 lines
Thanks,
RafaelQuoted 25 lines
Quoted 25 lines
Quoted 25 lines
Quoted 25 lines
--- sound/pci/hda/hda_intel.c | 6 ++++++ 1 file changed, 6 insertions(+)sound/pci/hda/hda_intel.c +6
-1@@ -3755,6 +3755,12 @@ static int azx_probe(struct pci_dev *pci,if (pci_dev_run_wake (pci))pm_runtime_put_noidle (&pci->dev); +else if (chip->driver_caps + &AZX_DCAPS_I915_POWERWELL ) { +/* Haswell doesnot support runtime pm by default */ +pm_runtime_put_noidle (&pci->dev); +pm_runtime_allow (&pci->dev); + } dev++;complete_all (&chip->probe_wait); --1.7.9.5
Quoted 61 lines · Xingchao
Hi Rafael,
Quoted 58 lines
-----Original Message-----
From: Wysocki, Rafael J
Sent: Wednesday, May 22, 2013 7:09 PM
To: Takashi Iwai
Cc: Wang, Xingchao; Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellQuoted 24 lines · Takashi Iwai
At Wed, 22 May 2013 03:56:00 +0000,
Quoted 22 lines · Xingchao
Hi,
Add Rafael in loop.
Quoted 10 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellAt Thu, 16 May 2013 16:29:05 +0800,
Wang Xingchao wrote:Quoted 7 lines
Quoted 5 lines
Haswell doesnot support runtime pm by default. This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.
Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
I wonder whether it's HD-A driver's policy to only support runtime PM if the
device can support signal wakup?
Quoted 1 line
Quoted 1 line
According to Rafael, the device can support runtime PM regardless, no
matter it supports PME or not.
Quoted 3 lines
Quoted 1 line
If so, we should remove the "if" condition check here.
Well, if the decision is purely a driver issue, then we can get rid of PME check.
Yes, it is.
Quoted 17 lines
But in that case, it should be simply like:
azx_probe() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_put_noidle(&pci->dev); ... }azx_remove() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_get_noresume(&pci->dev); ... }
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
AFAIU, calling
pm_runtime_allow()enables the runtime PM *forcibly*. Usually this isn't a good thing.That's correct. Moreover, calling both
pm_runtime_allow()*and*pm_runtime_put_noidle()together would be a bug IMO.It's interesting something maybe wrong in my test:
1. withtout callingpm_runtime_allow(), azx_runteim_idle/suspend() will not be called.
That's because you need to echo "auto" into the device's /sys/devices/.../power/control file from user space for it to work (most likely that's the reason). If that file already contains "auto" when this happens, I'll need to look at the code to tell you what may be wrong.
Quoted 8 lines
2. another trick is on my Haswell ULT C stepping board, the runtime PM only work after exit from resume:
echo mem >
/sys/power/stateif you donot let system enter suspend manually, the runtime pm will not be triggered.
Is there any dependency between runtime pm suspend and normal suspend?
There shouldn't be any like this, and if there's one, it is a bug most likely.
Thanks,
Rafael
---------------------------------------------------------------------
Intel Technology Poland sp. z o.o.
z siedziba w Gdansku
ul. Slowackiego 173
80-298 Gdansk
Sad Rejonowy Gdansk Polnoc w Gdansku, VII Wydzial Gospodarczy Krajowego Rejestru Sadowego, numer KRS 101882
NIP 957-07-52-316
Kapital zakladowy 200.000 zl
This e-mail and any attachments may contain confidential material for the sole use of the intended recipient(s). Any review or distribution by others is strictly prohibited. If you are not the intended recipient, please contact the sender and delete all copies.
Hi Rafael,
Quoted 76 lines
-----Original Message-----
From: Wysocki, Rafael J
Sent: Monday, May 27, 2013 9:02 PM
To: Wang, Xingchao
Cc: Takashi Iwai; Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellQuoted 67 lines · Xingchao
Hi Rafael,
Quoted 64 lines
-----Original Message-----
From: Wysocki, Rafael J
Sent: Wednesday, May 22, 2013 7:09 PM
To: Takashi Iwai
Cc: Wang, Xingchao; Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellQuoted 24 lines · Takashi Iwai
At Wed, 22 May 2013 03:56:00 +0000,
Quoted 22 lines · Xingchao
Hi,
Add Rafael in loop.
Quoted 8 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, May 16, 2013 4:49 PM
To: Wang Xingchao
Cc: Girdwood, Liam R; Lin, Mengdong; Li, Jocelyn; [email protected]; Wang, Xingchao
Subject: Re: [PATCH] ALSA: hda - Enable runtime pm for HaswellQuoted 8 lines
Quoted 5 lines · Wang Xingchao
Haswell doesnot support runtime pm by default. This patch let haswell Display HD-A controller enter runtime suspend, and bring more power saving whith power-well.
Signed-off-by Wang Xingchao <[email protected]>I don't think it's good to fiddle such a thing in the driver side. If Haswell can support runtime PM really, it should be set commonly.
I wonder whether it's HD-A driver's policy to only support runtime PM if the
device can support signal wakup?
Quoted 2 lines
Quoted 2 lines
According to Rafael, the device can support runtime PM regardless, no
matter it supports PME or not.
Quoted 3 lines
Quoted 1 line
If so, we should remove the "if" condition check here.
Well, if the decision is purely a driver issue, then we can get rid of PME check.
Yes, it is.
Quoted 17 lines
But in that case, it should be simply like:
azx_probe() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_put_noidle(&pci->dev); ... }azx_remove() { ... if (chip->driver_caps & AZX_DCAPS_PM_RUNTIME) pm_runtime_get_noresume(&pci->dev); ... }Quoted 3 lines
AFAIU, calling
pm_runtime_allow()enables the runtime PM *forcibly*. Usually this isn't a good thing.That's correct. Moreover, calling both
pm_runtime_allow()*and*pm_runtime_put_noidle()together would be a bug IMO.
Quoted 8 lines
Quoted 2 lines
It's interesting something maybe wrong in my test:
1. withtout callingpm_runtime_allow(), azx_runteim_idle/suspend() will notbe called.
That's because you need to echo "auto" into the device's
/sys/devices/.../power/controlfile from user space for it to work (most likely that's the reason). If that file already contains "auto" when this happens, I'll need to look at the code to tell you what may be wrong.
Yes, it works after echo "auto" into hda pci device, it's "on" by default. :)
Thanks
---xingchao
Quoted 15 lines
Quoted 7 lines
2. another trick is on my Haswell ULT C stepping board, the runtime PM only work after exit from resume:
echo mem >
/sys/power/stateif you donot let system enter suspend manually, the runtime pm will not be
triggered.
Quoted 2 lines
Is there any dependency between runtime pm suspend and normal suspend?
There shouldn't be any like this, and if there's one, it is a bug most likely.
Thanks,
Rafael