ipr: IOA Status Code(IOASC) update
Subsystems (2)
v2 cover ipr: IOA Status Code(IOASC) update
The patch updates some new IOA Status Code(IOASC) in ipr driver.
Thanks for your help!
Wendy
PATCH v2 1/1 ipr: IOA Status Code(IOASC) update
The patch updates some new IOA Status Code(IOASC) in ipr driver.
Signed-off-by Wen Xiong <[email protected]>
--- drivers/scsi/ipr.c | 40 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 39 insertions(+), 1 deletion(-)
drivers/scsi/ipr.c +39 -1
@@ -281,12 +281,22 @@ struct ipr_error_table_t ipr_error_table "FFF6: Failure prediction threshold exceeded"}, {0x015D9200 ,0 ,IPR_DEFAULT_LOG_LEVEL , "8009: Impending cache battery pack failure"}, + {0x02040100, 0, 0, + "Logical Unit in process of becoming ready"}, + {0x02040200, 0, 0, + "Initializing command required"}, {0x02040400, 0, 0, "34FF: Disk device format in progress"}, + {0x02040C00, 0, 0, + "Logical unit not accessible, target port in unavailable state"}, {0x02048000, 0, IPR_DEFAULT_LOG_LEVEL, "9070: IOA requested reset"}, {0x023F0000, 0, 0, "Synchronization required"}, + {0x02408500, 0, 0, + "IOA microcode download required"}, + {0x02408600, 0, 0, + "Device bus connection is prohibited by host"}, {0x024E0000, 0, 0, "No ready, IOA shutdown"}, {0x025A0000, 0, 0,
@@ -385,6 +395,8 @@ struct ipr_error_table_t ipr_error_table "4030: Incorrect multipath connection"}, {0x04679000 ,0 ,IPR_DEFAULT_LOG_LEVEL , "4110: Unsupported enclosure function"}, + {0x04679800, 0, IPR_DEFAULT_LOG_LEVEL, + "4120: SAS cable VPD cannot be read"}, {0x046E0000, 0, IPR_DEFAULT_LOG_LEVEL, "FFF4: Command to logical unit failed"}, {0x05240000, 1, 0,
@@ -407,10 +419,18 @@ struct ipr_error_table_t ipr_error_table "Illegal request, command sequence error"}, {0x052C8000 ,1 ,0 , "Illegal request, dual adapter support not enabled"}, + {0x052C8100, 1, 0, + "Illegal request, another cable connector was physically disabled"}, + {0x054E8000, 1, 0, + "Illegal request, inconsistent group id/group count"}, {0x06040500, 0, IPR_DEFAULT_LOG_LEVEL, "9031: Array protection temporarily suspended, protection resuming"}, {0x06040600, 0, IPR_DEFAULT_LOG_LEVEL, "9040: Array protection temporarily suspended, protection resuming"}, + {0x060B0100, 0, IPR_DEFAULT_LOG_LEVEL, + "4080: IOA exceeded maximum operating temperature"}, + {0x060B8000, 0, IPR_DEFAULT_LOG_LEVEL, + "4085: Service required"}, {0x06288000, 0, IPR_DEFAULT_LOG_LEVEL, "3140: Device bus not ready to ready transition"}, {0x06290000, 0, IPR_DEFAULT_LOG_LEVEL,
@@ -423,6 +443,8 @@ struct ipr_error_table_t ipr_error_table "FFFB: SCSI bus was reset by another initiator"}, {0x063F0300 ,0 ,IPR_DEFAULT_LOG_LEVEL , "3029: A device replacement has occurred"}, + {0x063F8300, 0, IPR_DEFAULT_LOG_LEVEL, + "4102: Device bus fabric performance degradation"}, {0x064C8000, 0, IPR_DEFAULT_LOG_LEVEL, "9051: IOA cache data exists for a missing or failed device"}, {0x064C8100, 0, IPR_DEFAULT_LOG_LEVEL,
@@ -445,6 +467,14 @@ struct ipr_error_table_t ipr_error_table "9076: Configuration error, missing remote IOA"}, {0x06679100 ,0 ,IPR_DEFAULT_LOG_LEVEL , "4050: Enclosure does not support a required multipath function"}, + {0x06679800, 0, IPR_DEFAULT_LOG_LEVEL, + "4121: Configuration error, required cable is missing"}, + {0x06679900, 0, IPR_DEFAULT_LOG_LEVEL, + "4122: Cable is not plugged into the correct location on remote IOA"}, + {0x06679A00, 0, IPR_DEFAULT_LOG_LEVEL, + "4123: Configuration error, invalid cable vital product data"}, + {0x06679B00, 0, IPR_DEFAULT_LOG_LEVEL, + "4124: Configuration error, both cable ends are plugged into the same IOA"}, {0x06690000, 0, IPR_DEFAULT_LOG_LEVEL, "4070: Logically bad block written on device"}, {0x06690200, 0, IPR_DEFAULT_LOG_LEVEL,
@@ -507,10 +537,18 @@ struct ipr_error_table_t ipr_error_table "9062: One or more disks are missing from an array"}, {0x07279900 ,0 ,IPR_DEFAULT_LOG_LEVEL , "9063: Maximum number of functional arrays has been exceeded"}, + {0x07279A00, 0, 0, + "Data protect, other volume set problem"}, {0x0B260000, 0, 0, "Aborted command, invalid descriptor"}, + {0x0B3F9000, 0, 0, + "Target operating conditions have changed, dual adapter takeover"}, + {0x0B530200, 0, 0, + "Aborted command, medium removal prevented"}, {0x0B5A0000, 0, 0, - "Command terminated by host"} + "Command terminated by host"}, + {0x0B5B8000, 0, 0, + "Aborted command, command terminated by host"} }; static const struct ipr_ses_table_entry ipr_ses_table[] = {
Quoted 4 lines · On 06/04/2013 06:57 PM, [email protected] wrote:
The patch updates some new IOA Status Code(IOASC) in ipr driver.
Signed-off-by Wen Xiong <[email protected]>---
Acked-by Brian King <[email protected]>
Thanks,
Brian
Signature · 3 lines
Brian King Power Linux I/O IBM Linux Technology Center
Hi James,
Can you double check if you have any questions about this patch?
Thanks for your help!
Wendy
Quoting Brian King <[email protected]>:
Quoted 16 lines · On 06/04/2013 06:57 PM, [email protected] wrote:
Quoted 4 lines
The patch updates some new IOA Status Code(IOASC) in ipr driver.
Signed-off-by Wen Xiong <[email protected]>---
Acked-by Brian King <[email protected]>Thanks,
Brian
--
Brian King
Power Linux I/O
IBM Linux Technology Center