Skip to contentSkip to conversation

SATA hotplug not detecting new disks

DISCUSSION Dave Hansen 2 participants 4 messages Jul 25, 2013 – Jul 26, 2013 libata

lore
Share & tools
lore
#0 lore raw

I've got a relatively new system that doesn't seem to be able to hotplug SATA disks. I see the same behavior on 3.10, 3.11-rc2, and Ubuntu's 3.8.0-25-generic. The disks are detected right away on reboots, but even after poking the /sys/class/scsi_host/host*/scan files, new disks are never detected. I've disabled link power management.

Am I doing something stupid here? I thought this "just worked" on my previous hardware.

The motherboard is an Intel DH87RL. The SATA controller is:

Quoted 11 lines

00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 204a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]

Quoted 8 lines

Region 5: Memory at f7d3a000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee2200c Data: 4191
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci

Relevant dmesg from boot:

ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 5 ports 6 Gbps 0x1e impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
ata1: DUMMY
ata2: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a180 irq 41
ata3: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a200 irq 41
ata4: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a280 irq 41
ata5: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a300 irq 41

#1 lore raw
Quoted 8 lines · Dave Hansen

I've got a relatively new system that doesn't seem to be able to hotplug SATA disks. I see the same behavior on 3.10, 3.11-rc2, and Ubuntu's 3.8.0-25-generic. The disks are detected right away on reboots, but even after poking the /sys/class/scsi_host/host*/scan files, new disks are never detected. I've disabled link power management.

Am I doing something stupid here? I thought this "just worked" on my previous hardware.

My vague memory reminds me that not all SATA ports are hot pluggable - you can check the port's "External SATA port" bit and "Hot Plug Capable" bit of the PxCMD register like this:

$ grep ahci /proc/iomem 
    e1a40000-e1a407ff : ahci
# dd if=/dev/mem of=ahcidump bs=4096 count=1 skip=0xe1a40
You will need to change 0xe1a40 to decimal format.

Then the PxCMD is at offset 0x118 for port 0, check bit 21 for E-SATA or bit 18 for hot pluggable bits. If any of them set to 1, this port should be hot pluggable; otherwise, it doesn't have this capability.

Quoted 23 lines

The motherboard is an Intel DH87RL. The SATA controller is:

Quoted 11 lines

00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 204a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]

Quoted 8 lines

Region 5: Memory at f7d3a000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee2200c Data: 4191
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci

Quoted 7 lines

Relevant dmesg from boot:

ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 5 ports 6 Gbps 0x1e impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst

This doesn't have sxs(support external sata) bit here, so no ports from this host is E-SATA port. Only need to check the hot pluggable bit.

Hope this helps,
-Aaron

Quoted 12 lines

ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
ata1: DUMMY
ata2: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a180 irq 41
ata3: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a200 irq 41
ata4: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a280 irq 41
ata5: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a300 irq 41

#2 lore raw
Quoted 14 lines · Aaron Lu
Quoted 8 lines · Dave Hansen

I've got a relatively new system that doesn't seem to be able to hotplug SATA disks. I see the same behavior on 3.10, 3.11-rc2, and Ubuntu's 3.8.0-25-generic. The disks are detected right away on reboots, but even after poking the /sys/class/scsi_host/host*/scan files, new disks are never detected. I've disabled link power management.

Am I doing something stupid here? I thought this "just worked" on my previous hardware.

My vague memory reminds me that not all SATA ports are hot pluggable - you can check the port's "External SATA port" bit and "Hot Plug Capable" bit of the PxCMD register like this:

Quoted 8 lines
$ grep ahci /proc/iomem 
    e1a40000-e1a407ff : ahci
# dd if=/dev/mem of=ahcidump bs=4096 count=1 skip=0xe1a40
You will need to change 0xe1a40 to decimal format.

Then the PxCMD is at offset 0x118 for port 0, check bit 21 for E-SATA or bit 18 for hot pluggable bits. If any of them set to 1, this port should be hot pluggable; otherwise, it doesn't have this capability.

That whole I/O area looks to be 0'd to me, at least for the port if I boot with it unplugged. I even tried toggling the PORT_CMD_ALPE bit with powertop since it is in the same port. Nothing seems to happen for port0 (the one unplugged at boot), although I _can_ see the writes show up for the other ports.

I also tried booting with a disk plugged in to a port, then put that disk to sleep and unplugged it. I replugged a _different_ disk in its place, and it was detected just fine.

Is it possible that the 'ata_dummy_port_ops' are getting left in place at boot accidentally, that we're mistaking an unplugged port for a disabled one?

#3 lore raw
In reply to Aaron Lu
Quoted 13 lines · Aaron Lu
Quoted 8 lines · Dave Hansen
Quoted 8 lines

I've got a relatively new system that doesn't seem to be able to hotplug SATA disks. I see the same behavior on 3.10, 3.11-rc2, and Ubuntu's 3.8.0-25-generic. The disks are detected right away on reboots, but even after poking the /sys/class/scsi_host/host*/scan files, new disks are never detected. I've disabled link power management.

Am I doing something stupid here? I thought this "just worked" on my previous hardware.

My vague memory reminds me that not all SATA ports are hot pluggable - you can check the port's "External SATA port" bit and "Hot Plug Capable" bit of the PxCMD register like this:

Quoted 8 lines
$ grep ahci /proc/iomem 
    e1a40000-e1a407ff : ahci
# dd if=/dev/mem of=ahcidump bs=4096 count=1 skip=0xe1a40
You will need to change 0xe1a40 to decimal format.

Then the PxCMD is at offset 0x118 for port 0, check bit 21 for E-SATA or bit 18 for hot pluggable bits. If any of them set to 1, this port should be hot pluggable; otherwise, it doesn't have this capability.

<sigh>

I went digging back through the BIOS settings, and found a nice checkbox to enable hotplug support on the ports. All seems happy now.

Thanks for the help. I hope someone else googling will hit this thread. :)