80211s with DFS
hi mailinglist!
i have a real big problem! i'm trying to implement a wireless-mesh (80211s) with openWRT (current trunk) over 11a (5GHz) with "authSAE" for outdoor. all works fine, mesh is runnning and all fine. but now, i'm at germany and for the outdoor use, i have to use the channel 100-140 with DFS & TPC. so the mesh implementation dont work in this channel? with this error:
authSAE config:
#######################################################
authsae:
{
sae:
{
debug = 480;
password = "foobar";
group = [19, 26, 21, 25, 20];
blacklist = 5;
thresh = 5;
lifetime = 3600;
};
meshd:
{
meshid = "foobar";
interface = "mesh0";
band = "11a";
channel = 104;
htmode = "ht20";
mcast-rate = 6;
debug = 1; };
};
#######################################################
starting mesh with "authSAE":
#######################################################
# meshd-nl80211 -c /etc/authsae.cfg ---------- nlcfg rates hexdump 00 3c 00 5a 00 78 00 b4 00 f0 01 68 01 e0 02 1c ----------
----------
mgtk: hexdump
ce 5a b3 fc 8b 76 db 62 11 c9 58 33 fa 0c 26 88
----------
----------
Fixed Information Elements in this STA hexdump
01 08 8c 12 98 24 b0 48 60 6c
----------
meshd: Starting mesh with mesh id = foobar
----------
basic rates: hexdump
8c 98 b0
----------
joining mesh foobar on freq 3443784, mode 0
nlerror, cmd 68, seq 1376254403: Invalid argument
#######################################################
and this is without "authSAE":
#######################################################
# iw mesh0 set channel 104 # iw mesh0 mesh join foobar command failed: Invalid argument (-22) #######################################################
but this is working with a non-DFS channel 44:
#######################################################
# iw mesh0 set channel 44 # iw mesh0 mesh join hackewrt [21044.240000] IPv6: ADDRCONF(NETDEV_CHANGE): mesh0: link becomes ready [21044.240000] mesh-br: port 1(vlan11) entered forwarding state [21044.250000] mesh-br: port 1(vlan11) entered forwarding state [21044.260000] IPv6: ADDRCONF(NETDEV_CHANGE): vlan11: link becomes ready [21044.260000] coova-br: port 1(vlan12) entered forwarding state [21044.270000] coova-br: port 1(vlan12) entered forwarding state [21044.280000] IPv6: ADDRCONF(NETDEV_CHANGE): vlan12: link becomes ready root@6470028F55A2:~#
#######################################################
i think this error is from the "netlink lib(libnl genl)"...
if i use a channel without DFS, it works fine (in germany channel like 36-48)... so how it is possible to use mesh (80211s) with DFS ?
big thx for answer,
volker...
Quoted 4 lines · On Sun, Aug 11, 2013 at 11:03:38PM +0200, Volker von Hoesslin @ SKBX Systems…
i think this error is from the "netlink lib(libnl genl)"...
if i use a channel without DFS, it works fine (in germany channel like 36-48)... so how it is possible to use mesh (80211s) with DFS ?
mac80211 does not support DFS in mesh mode so far, the only DFS support implemented is AP mode (and only with ath9k compatible chips). I'm currently working on IBSS, I don't if/who will work on 802.11s DFS ...
Cheers,
Simon
Quoted 3 lines
I'm currently working on IBSS, I don't if/who will work on 802.11s DFS ...
it is possible to speed up this work? maybe pay for it!
Quoted 7 lines
-----Original Message-----
From: [email protected] [mailto:linux-wireless- [email protected]] On Behalf Of Volker von Hoesslin @ SKBX Systemsi have a real big problem! i'm trying to implement a wireless-mesh (80211s) with openWRT (current trunk) over 11a (5GHz) with "authSAE"
for
Quoted 1 line
outdoor. all works fine, mesh is runnning and all fine. but now, i'm
at
Quoted 1 line
germany and for the outdoor use, i have to use the channel 100-140
with DFS
Quoted 3 lines
& TPC. so the mesh implementation dont work in this channel? with this error:
Hi
The real difficulty with DFS and 802.11s is what happens when a radar is detected? All mesh nodes need to be on the same channel, so there needs to be some consistent way of propagating a channel switch announcement to all wireless nodes.
Brett
Quoted 6 lines
The real difficulty with DFS and 802.11s is what happens when a radar is detected? All mesh nodes need to be on the same channel, so there needs to be some consistent way of propagating a channel switch announcement to all wireless nodes.
indeed, thats a hard question. my first hint is looking at cisco (http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.0/design/guide/MeshAP_70.pdf -> page 169), but 80211s has't a RAP so maybe there are only some tips for a workflow.
i think there are diffrent possibilities:
1. the MAP that has a radar detection go sleep and wait till the channel is clear to come back -> mesh will down :/
2. the mesh has to negotiate a new free channel via bacon-frames, maybe generating preventively a list of channel for switching?
3. some other ideas ?
is there someone at work for a DFS implementation?
volker...