Skip to contentSkip to conversation

SPL binary too large for OMAP4460 OCM

U-Boot bin4ry 4 participants 8 messages Sep 4, 2013 – Sep 5, 2013 Arm (32-bit)

lore
Share & tools
lore

bin4ry

author
#0 lore raw

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Thanks a lot,
-b

#1 lore raw
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

Regards,
Sricharan

#2 lore raw

Hi

Quoted 16 lines · Sricharan R
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 9 lines
Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Michael

Quoted 6 lines

Regards,
Sricharan
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#3 lore raw
Quoted 26 lines · Michael Trimarchi

Hi

Quoted 23 lines · Sricharan R
Quoted 22 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Quoted 5 lines
Quoted 2 lines

Do you have a Secure device or GP ?

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Sorry i missed to read PANDA. So it is anyways GP. and you changed the CONFIG_SPL_TEXT_BASE as well right ?

Regards,
Sricharan

author
#4 lore raw

Am 04.09.2013 10:56, schrieb Sricharan R:

Quoted 29 lines · Michael Trimarchi
Quoted 28 lines

Hi

Quoted 25 lines · Sricharan R
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

Quoted 8 lines
Quoted 3 lines

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Sorry i missed to read PANDA. So it is anyways GP. and you changed the CONFIG_SPL_TEXT_BASE as well right ?

Regards,
Sricharan

First off, sorry for double-posting to this list.

No, the PandaBoard is no HS but a GP device.

This is my configuration:

/* Defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_TEXT_BASE 0x40303000
#define CONFIG_SPL_MAX_SIZE (45 * 1024)
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

The MLO binary has 46094 Bytes. Actually I should have enough space (from 0x40300000 - 0x4030bfff -> ~49 kB). However, the device does not start. Right now I am reviewing the code to check, whether it is because of the code and not because of the size that makes u-boot does not start.

#5 lore raw
Quoted 50 lines · On Wednesday 04 September 2013 02:34 PM, bin4ry wrote:

Am 04.09.2013 10:56, schrieb Sricharan R:

Quoted 29 lines · Michael Trimarchi
Quoted 28 lines

Hi

Quoted 25 lines · Sricharan R
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

Quoted 8 lines
Quoted 3 lines

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Sorry i missed to read PANDA. So it is anyways GP. and you changed the CONFIG_SPL_TEXT_BASE as well right ?

Regards,
Sricharan

First off, sorry for double-posting to this list.

No, the PandaBoard is no HS but a GP device.

This is my configuration:

/* Defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_TEXT_BASE 0x40303000
#define CONFIG_SPL_MAX_SIZE (45 * 1024)
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

Quoted 4 lines

The MLO binary has 46094 Bytes. Actually I should have enough space (from 0x40300000 - 0x4030bfff -> ~49 kB). However, the device does not start. Right now I am reviewing the code to check, whether it is because of the code and not because of the size that makes u-boot does not start.

Can you try by setting CONFIG_SPL_TEXT_BASE 0x40300350 ?

Regards,
Sricharan

author
#6 lore raw

Hi everyone,

I changed CONFIG_SPL_TEXT_BASE from 0x40300300 to 0x40300350 and sufddenly it works. Do you know why this configuration works, even though with this configuration there are 0x50 bytes less? It even works with a MLO with 47519 bytes.

Here the summary of my config:

/* Defines for SPL */
#define CONFIG_SPL

#define CONFIG_SPL_TEXT_BASE            0x40300350
#define CONFIG_SPL_MAX_SIZE             (46 * 1024)
#define CONFIG_SPL_STACK                LOW_LEVEL_SRAM_STACK

Thanks again for the support!
-b

Am 04.09.2013 11:07, schrieb Sricharan R:

Quoted 59 lines · On Wednesday 04 September 2013 02:34 PM, bin4ry wrote:
Quoted 50 lines

Am 04.09.2013 10:56, schrieb Sricharan R:

Quoted 29 lines · Michael Trimarchi
Quoted 28 lines

Hi

Quoted 25 lines · Sricharan R
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

Quoted 8 lines
Quoted 3 lines

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Sorry i missed to read PANDA. So it is anyways GP. and you changed the CONFIG_SPL_TEXT_BASE as well right ?

Regards,
Sricharan

First off, sorry for double-posting to this list.

No, the PandaBoard is no HS but a GP device.

This is my configuration:

/* Defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_TEXT_BASE 0x40303000
#define CONFIG_SPL_MAX_SIZE (45 * 1024)
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

Quoted 4 lines

The MLO binary has 46094 Bytes. Actually I should have enough space (from 0x40300000 - 0x4030bfff -> ~49 kB). However, the device does not start. Right now I am reviewing the code to check, whether it is because of the code and not because of the size that makes u-boot does not start.

Can you try by setting CONFIG_SPL_TEXT_BASE 0x40300350 ?

Regards,
Sricharan

#7 lore raw
In reply to bin4ry

Hi,

Quoted 50 lines · On Wednesday 04 September 2013 02:34 PM, bin4ry wrote:

Am 04.09.2013 10:56, schrieb Sricharan R:

Quoted 29 lines · Michael Trimarchi
Quoted 28 lines

Hi

Quoted 25 lines · Sricharan R
Quoted 15 lines · On Wednesday 04 September 2013 01:01 PM, bin4ry wrote:

Hi everybody,

I need to add functionality to the SPL code. I tried to implement in a memory-saving way, however, the SPL is about 45 kB after compilation. To get compilation working, I had to set CONFIG_SPL_MAX_SIZE to (45 * 1024). Now, the SPL as well as u-boot won't boot. After the device' (PandaBoard ES - OMAP4460) reset, nothing happens regarding it's output on terminal.

My question: is it theoretically possible to to establish a successfully booting SPL with ~45 kB in size for this device? The device' on-chip-memory is 56kB so it could fit in there. If so, what needs to be configured / tuned to get it working? Are there any other features I could omit from the binary to make it smaller?

Quoted 7 lines

Thanks a lot,
-b
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Do you have a Secure device or GP ?

Quoted 8 lines
Quoted 3 lines

if it is Pandaboard? No he has not. I have increased up to 40Kb and it works with serial boot and
sdcard/emmc boot.

Sorry i missed to read PANDA. So it is anyways GP. and you changed the CONFIG_SPL_TEXT_BASE as well right ?

Regards,
Sricharan

First off, sorry for double-posting to this list.

No, the PandaBoard is no HS but a GP device.

This is my configuration:

/* Defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_TEXT_BASE 0x40303000
#define CONFIG_SPL_MAX_SIZE (45 * 1024)
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

Quoted 4 lines

The MLO binary has 46094 Bytes. Actually I should have enough space (from 0x40300000 - 0x4030bfff -> ~49 kB). However, the device does not start. Right now I am reviewing the code to check, whether it is because of the code and not because of the size that makes u-boot does not start.

Just for testing you can try the following diff:
The start address where the Image is downloaded is changed and now the max size is ~46KB.

arch/arm/include/asm/arch-omap4/omap.h +1 -1
index 3823a37..7c98360 100644
@@ -109,7 +109,7 @@ struct s32ktimer {
  * Non-secure RAM starts at 0x40300000 for GP devices. But we keep SRAM_BASE
  * at 0x40304000(EMU base) so that our code works for both EMU and GP
  */
-#define NON_SECURE_SRAM_START	0x40304000
+#define NON_SECURE_SRAM_START	0x40300000
 #define NON_SECURE_SRAM_END	0x4030E000	/* Not inclusive */
 #define SRAM_SCRATCH_SPACE_ADDR	NON_SECURE_SRAM_START
 /* base address for indirect vectors (internal boot mode) */
include/configs/omap4_common.h +2 -2
index e9f2383..5177313 100644
@@ -250,8 +250,8 @@
 /* Defines for SPL */
 #define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_TEXT_BASE		0x40304350
-#define CONFIG_SPL_MAX_SIZE		(38 * 1024)
+#define CONFIG_SPL_TEXT_BASE		0x40300000
+#define CONFIG_SPL_MAX_SIZE		0x4030C000 - CONFIG_SPL_TEXT_BASE
 #define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
 #define CONFIG_SPL_DISPLAY_PRINT
 

Thanks and regards,
Lokesh

Quoted 5 lines

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot