ppc4xx: Fix GPIO handling in lwmon5 and lcd4_lwmon5 BSP
PATCH 1/1 ppc4xx: Fix GPIO handling in lwmon5 and lcd4_lwmon5 BSP
LCD4 needs a slightly different GPIO configuration than the original LWMON5 variant. GPIO49 needs to be configured to a default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Signed-off-by Stefan Roese <[email protected]>
--- board/lwmon5/lwmon5.c | 3 +++ include/configs/lwmon5.h | 10 +++++++++- 2 files changed, 12 insertions(+), 1 deletion(-)
board/lwmon5/lwmon5.c +3 -0
@@ -527,6 +527,9 @@ void spl_board_init(void)*/ board_early_init_f (); +/* enable the LSB transmitter */ +gpio_write_bit (CONFIG_SYS_GPIO_LSB_ENABLE ,1 ); +/* * Clear resets */
include/configs/lwmon5.h +9 -1
@@ -565,6 +565,7 @@#define CONFIG_SYS_GPIO_PHY1_RST 12#define CONFIG_SYS_GPIO_FLASH_WP 14#define CONFIG_SYS_GPIO_PHY0_RST 22 +#define CONFIG_SYS_GPIO_PERM_VOLT_FEED 49#define CONFIG_SYS_GPIO_DSPIC_READY 51#define CONFIG_SYS_GPIO_CAN_ENABLE 53#define CONFIG_SYS_GPIO_LSB_ENABLE 54
@@ -577,6 +578,13 @@#define CONFIG_SYS_GPIO_SYSMON_STATUS 62#define CONFIG_SYS_GPIO_WATCHDOG 63 +/* On LCD4, GPIO49 has to be configured to 0 instead of 1 */ +#ifdef CONFIG_LCD4_LWMON5 +#define GPIO49_VAL 0 +#else +#define GPIO49_VAL 1 +#endif +/* * PPC440 GPIO Configuration */
@@ -635,7 +643,7 @@ {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO49_VAL}, /* GPIO49 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
Signature · 1 line
1.8.3.4
PATCH 1/1 ppc4xx: Fix GPIO handling in lwmon5 and lcd4_lwmon5 BSP
Quoted 5 lines · Stefan Roese
LCD4 needs a slightly different GPIO configuration than the original LWMON5 variant. GPIO49 needs to be configured to a default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Applied to u-boot-ppc4xx/master.
Thanks,
Stefan