Skip to contentSkip to conversation

at91: add support for CDU9G25 board

PATCH Superseded Jiri Prchal 2 participants 2 messages Sep 13, 2013

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 at91: add support for CDU9G25 board

This patch adds support for our companies board CDU9G25 with Atmel AT91SAM9G25, 128MB DDR2, 256MB NAND.

---
v.2
Fixed static IP and MAC addr cofiguration by random MAC and DHCP. Added entry to MAINTAINERS.
Fixed line lenght, trailing spaces and other cosmetics. v.3
Removed static eth_gadget addresses.
MAC address set from serial number of F-RAM.
v.4
Changed debug to printf if used random MAC addr, print that addr. Keep MAC addr set in enviroment.

 MAINTAINERS               |    3 +
 board/cdu9g25/Makefile    |   34 +++++++
 board/cdu9g25/cdu9g25.c   |  204 ++++++++++++++++++++++++++++++++++++++++++
 board/cdu9g25/config.mk   |    1 +
 boards.cfg                |    1 +
 include/configs/cdu9g25.h |  216 +++++++++++++++++++++++++++++++++++++++++++++
 6 files changed, 459 insertions(+)
 create mode 100644 board/cdu9g25/Makefile
 create mode 100644 board/cdu9g25/cdu9g25.c
 create mode 100644 board/cdu9g25/config.mk
 create mode 100644 include/configs/cdu9g25.h
MAINTAINERS +3 -0
index bd0f3a0..9d0008a 100644
@@ -851,6 +851,9 @@ Matt Porter <[email protected]>
 
 	ti814x_evm	ARM ARMV7 (TI814x Soc)
 
+Jiri Prchal <[email protected]>
+	cdu9g25			ARM926EJS (AT91SAM9G25 SoC)
+
 Dave Purdy <[email protected]>
 
 	pogo_e02	ARM926EJS (Kirkwood SoC)
board/cdu9g25/Makefile new file +34 -0
new file mode 100644
index 0000000..b644a83
@@ -0,0 +1,34 @@
+#
+# U-boot - Makefile
+#
+# (C) Copyright 2013
+# Jiri Prchal <[email protected]>
+# AK signal <www.aksignal.cz>
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= cdu9g25.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/cdu9g25/cdu9g25.c new file +204 -0

204 lines not on this page · raw message

board/cdu9g25/config.mk new file +1 -0
new file mode 100644
index 0000000..528ed4a
@@ -0,0 +1 @@
+CONFIG_SYS_TEXT_BASE = 0x27f00000
boards.cfg +1 -0
index be810c7..572d20d 100644
@@ -77,6 +77,7 @@ integratorcp_cm926ejs        arm         arm926ejs   integrator          armltd
 aspenite                     arm         arm926ejs   -                   Marvell        armada100
 gplugd                       arm         arm926ejs   -                   Marvell        armada100
 afeb9260                     arm         arm926ejs   -                   -              at91
+cdu9g25                      arm         arm926ejs   -                   -              at91
 at91sam9260ek_dataflash_cs0  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS0
 at91sam9260ek_dataflash_cs1  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS1
 at91sam9260ek_nandflash      arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH
include/configs/cdu9g25.h new file +216 -0

216 lines not on this page · raw message

--
1.7.9.5

#1 lore raw

PATCH v4 1/1 at91: add support for CDU9G25 board

Hi Jiri Prchal,
Quickly go through the code, please take the following comments as a
reference.

Add Andreas in loop.

Quoted 32 lines · Jiri Prchal

This patch adds support for our companies board CDU9G25 with Atmel AT91SAM9G25, 128MB DDR2, 256MB NAND.

---
v.2
Fixed static IP and MAC addr cofiguration by random MAC and DHCP. Added entry to MAINTAINERS.
Fixed line lenght, trailing spaces and other cosmetics. v.3
Removed static eth_gadget addresses.
MAC address set from serial number of F-RAM.
v.4
Changed debug to printf if used random MAC addr, print that addr. Keep MAC addr set in enviroment.

  MAINTAINERS               |    3 +
  board/cdu9g25/Makefile    |   34 +++++++
  board/cdu9g25/cdu9g25.c   |  204 ++++++++++++++++++++++++++++++++++++++++++
  board/cdu9g25/config.mk   |    1 +
  boards.cfg                |    1 +
  include/configs/cdu9g25.h |  216 +++++++++++++++++++++++++++++++++++++++++++++
  6 files changed, 459 insertions(+)

create mode 100644 board/cdu9g25/Makefile
create mode 100644 board/cdu9g25/cdu9g25.c
create mode 100644 board/cdu9g25/config.mk
create mode 100644 include/configs/cdu9g25.h

MAINTAINERS +0 -0
index bd0f3a0..9d0008a 100644

MAINTAINERS Matt Porter <[email protected]> · line 859

Quoted 9 lines
MAINTAINERS +3 -0
@@ -851,6 +851,9 @@ Matt Porter <[email protected]>
 
  	ti814x_evm	ARM ARMV7 (TI814x Soc)
 
+Jiri Prchal <[email protected]>
+	cdu9g25			ARM926EJS (AT91SAM9G25 SoC)
+
  Dave Purdy <[email protected]>
 
  	pogo_e02	ARM926EJS (Kirkwood SoC)

Consider to rebase to u-boot master branch, as the MAINTAINERS file is merged into boards.cfg file

Quoted 67 lines
board/cdu9g25/Makefile new file +34 -0
new file mode 100644
index 0000000..b644a83
@@ -0,0 +1,34 @@
+#
+# U-boot - Makefile
+#
+# (C) Copyright 2013
+# Jiri Prchal <[email protected]>
+# AK signal <www.aksignal.cz>
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= cdu9g25.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/cdu9g25/cdu9g25.c new file +21 -0
new file mode 100644
index 0000000..c7e78e3
@@ -0,0 +1,204 @@
+/*
+ * (C) Copyright 2013
+ * Jiri Prchal <[email protected]>
+ * AK signal <www.aksignal.cz>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9x5_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_spi.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <atmel_hlcdc.h>
+#include <atmel_mci.h>

board/cdu9g25/cdu9g25.c line 31

Quoted 10 lines
board/cdu9g25/cdu9g25.c new file +10 -0
+#include <spi.h>
+#include <net.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */

I think this is no meaning to put this comment here.

Quoted 37 lines
board/cdu9g25/cdu9g25.c new file +37 -0
+static void cdu9g25_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	unsigned long csa;
+
+	/* Enable CS3 */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
+	writel(csa, &matrix->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
+	       AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
+	       &smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6),
+	       &smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+		AT91_SMC_MODE_DBW_8 |
+		AT91_SMC_MODE_TDF_CYCLE(1),
+		&smc->cs[3].mode);
+
+	writel(1 << ATMEL_ID_PIOCD, &pmc->pcer);
+
+	/* Configure RDY/BSY */
+	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+	/* Enable NandFlash */
+	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+
+	at91_set_a_periph(AT91_PIO_PORTD, 0, 1);	/* NAND OE */
+	at91_set_a_periph(AT91_PIO_PORTD, 1, 1);	/* NAND WE */

board/cdu9g25/cdu9g25.c line 79

Quoted 10 lines
board/cdu9g25/cdu9g25.c new file +10 -0
+	at91_set_a_periph(AT91_PIO_PORTD, 2, 1);	/* NAND ALE */
+	at91_set_a_periph(AT91_PIO_PORTD, 3, 1);	/* NAND CLE */
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	debug("spi_cs_is_valid: bus=%u cs=%u\n", bus, cs);
+	if (bus < 2 && cs < 4)
+		return 1;
+	return 0;

Maybe need a black line here. I think change it globally.

Quoted 87 lines
board/cdu9g25/cdu9g25.c new file +87 -0
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	debug("spi_cs_activate: bus=%u cs=%u\n", slave->bus, slave->cs);
+	at91_set_pio_output(AT91_PIO_PORTA, 23, 0);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	debug("spi_cs_deactivate: bus=%u cs=%u\n", slave->bus, slave->cs);
+	at91_set_pio_output(AT91_PIO_PORTA, 23, 1);
+}
+
+void cdu9g25_spi0_hw_init(void)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* SPI0_MISO */
+	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* SPI0_MOSI */
+	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* SPI0_SPCK */
+
+	/* Enable clock */
+	writel(1 << ATMEL_ID_SPI0, &pmc->pcer);
+
+	at91_set_pio_output(AT91_PIO_PORTA, 23, 1);
+}
+
+void cdu9g25_init_enetaddr(void)
+{
+	struct spi_slave *slave;
+	uchar sernum[9];
+	int ret;
+
+	if (eth_getenv_enetaddr("ethaddr", sernum))
+		return;
+
+	slave = spi_setup_slave(0, 3, 1000000, SPI_MODE_0);
+	if (!slave) {
+		debug("Failed to set up FRAM slave\n");
+		goto err_spi_setup_slave;
+	}
+
+	ret = spi_claim_bus(slave);
+	if (ret) {
+		debug("Failed to claim SPI bus: %d\n", ret);
+		goto err_spi_claim_bus;
+	}
+
+	*sernum = 0xc3; /* opcode to read serial number */
+	ret = spi_xfer(slave, sizeof(sernum) * 8, sernum, sernum,
+		       SPI_XFER_BEGIN | SPI_XFER_END);
+	if (ret) {
+		debug("Failed to read serial#: %d\n", ret);
+		goto err_spi_xfer;
+	}
+
+	memmove(sernum + 1, sernum + 3, 6);
+	*sernum = 0x02;
+
+err_spi_xfer:
+	spi_release_bus(slave);
+err_spi_claim_bus:
+	spi_free_slave(slave);
+err_spi_setup_slave:
+	if (!is_valid_ether_addr(sernum)) {
+		eth_random_enetaddr(sernum);
+		printf("Using random MAC address %pM\n", sernum);
+	}
+	eth_setenv_enetaddr("ethaddr", sernum);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+
+	cdu9g25_init_enetaddr();
+	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
+	return rc;
+}
+
+static void cdu9g25_led_init(void)
+{
+	at91_set_gpio_output(CONFIG_LED_B, 1);
+	at91_set_gpio_value(CONFIG_LED_B, 0);
+}
+

board/cdu9g25/cdu9g25.c line 176

Quoted 10 lines
board/cdu9g25/cdu9g25.c new file +10 -0
+int board_early_init_f(void)
+{
+	at91_seriald_hw_init();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of AT91SAM9X5EK-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK;

Why use SAM9X5EK board mach type number?

Quoted 33 lines
board/cdu9g25/cdu9g25.c new file +27 -0
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	cdu9g25_led_init();
+
+	cdu9g25_nand_hw_init();
+
+	cdu9g25_spi0_hw_init();
+
+	at91_macb_hw_init();
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+		CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+}
+#endif
+
board/cdu9g25/config.mk new file +0 -0
new file mode 100644
index 0000000..528ed4a

board/cdu9g25/config.mk line 1

Quoted 1 line
board/cdu9g25/config.mk new file +1 -0
@@ -0,0 +1 @@
+CONFIG_SYS_TEXT_BASE = 0x27f00000

Move this to board configuration file.

Quoted 52 lines
boards.cfg +1 -0
index be810c7..572d20d 100644
@@ -77,6 +77,7 @@ integratorcp_cm926ejs        arm         arm926ejs   integrator          armltd
  aspenite                     arm         arm926ejs   -                   Marvell        armada100
  gplugd                       arm         arm926ejs   -                   Marvell        armada100
  afeb9260                     arm         arm926ejs   -                   -              at91
+cdu9g25                      arm         arm926ejs   -                   -              at91
  at91sam9260ek_dataflash_cs0  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS0
  at91sam9260ek_dataflash_cs1  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS1
  at91sam9260ek_nandflash      arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH
include/configs/cdu9g25.h new file +34 -0
new file mode 100644
index 0000000..d5eb992
@@ -0,0 +1,216 @@
+/*
+ * (C) Copyright 2013
+ * Jiri Prchal <[email protected]>
+ * AK signal <www.aksignal.cz>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+#define CONFIG_AT91SAM9X5
+#include <asm/hardware.h>
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* main clock xtal */
+#define CONFIG_SYS_HZ			1000
+
+/* Define actual evaluation board type from used processor type */
+#define CONFIG_CDU9G25
+#define CONFIG_AT91FAMILY
+#define CONFIG_IDENT_STRING	"_cdu9g25"
+
+/* Misc CPU related */
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT

include/configs/cdu9g25.h line 44

Quoted 10 lines
include/configs/cdu9g25.h new file +10 -0
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */
+
+/* LEDs */
+#define	CONFIG_LED_R		AT91_PIN_PB18
+#define	CONFIG_LED_G		AT91_PIN_PB16
+#define	CONFIG_LED_Y		AT91_PIN_PB14

I don't see where these three is used.

include/configs/cdu9g25.h line 50

Quoted 6 lines
include/configs/cdu9g25.h new file +6 -0
+#define	CONFIG_LED_B		AT91_PIN_PB12
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define	CONFIG_USART_ID			ATMEL_ID_SYS

alignment, use blank space replace tab

include/configs/cdu9g25.h line 52

Quoted 2 lines
include/configs/cdu9g25.h new file +2 -0
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }

we can let fallback function to define it.

Quoted 33 lines
include/configs/cdu9g25.h new file +33 -0
+
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_RESET_TO_RETRY
+#define CONFIG_BOOT_RETRY_TIME	600
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_AT91SAM9_WATCHDOG
+
+/* SPI */
+#define CONFIG_ATMEL_SPI
+#define CONFIG_CMD_SPI
+
+/* RAMTRON FRAM */
+#define CONFIG_CMD_SF
+#define CONFIG_ATMEL_SPI0		/* SPI used for FRAM is SPI0 */
+#define CONFIG_SPI_FLASH		/* RAMTRON FRAM on SPI bus */
+#define CONFIG_SPI_FRAM_RAMTRON
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS

include/configs/cdu9g25.h line 95

Quoted 10 lines
include/configs/cdu9g25.h new file +10 -0
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * SDRAM: 1 bank, min 32, max 128 MB

If the code run on board less than 128MiB DDR, it can not relocate the code.

Quoted 12 lines
include/configs/cdu9g25.h new file +12 -0
+ * Initialized before u-boot gets started.
+ */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000 /* ATMEL_BASE_CS1 */
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000
+
+/*
+ * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
+ * leaving the correct space for initial global data structure above
+ * that address while providing maximum stack area below.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 4 * 1024\

include/configs/cdu9g25.h line 117

Quoted 10 lines
include/configs/cdu9g25.h new file +10 -0
+				- GENERATED_GBL_DATA_SIZE)
+
+/* no NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* NAND flash */
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_DBW_8		1

No need this

include/configs/cdu9g25.h line 125

Quoted 8 lines
include/configs/cdu9g25.h new file +8 -0
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PD4
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PD5
+
+/* PMECC & PMERRLOC */
+#define CONFIG_ATMEL_NAND_HWECC		1
+#define CONFIG_ATMEL_NAND_HW_PMECC	1

no need "1"

include/configs/cdu9g25.h line 128

Quoted 3 lines
include/configs/cdu9g25.h new file +3 -0
+#define CONFIG_PMECC_CAP		8
+#define CONFIG_PMECC_SECTOR_SIZE	512
+#define CONFIG_PMECC_INDEX_TABLE_OFFSET	0x8000

This also can remove away, if you base on the u-boot master branch

Quoted 50 lines
include/configs/cdu9g25.h new file +50 -0
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_NAND_TRIMFFS
+#define MTDIDS_DEFAULT			"nand0=nand"
+#define MTDPARTS_DEFAULT		"mtdparts=nand:256k(bootstrap),"\
+					"768k(uboot),256k(ubootenv),"\
+					"4864k(kernel),"\
+					"-(root)"
+
+/* MMC */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+/* FAT */
+#ifdef CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_MACB_SEARCH_PHY
+#define CONFIG_RANDOM_MACADDR
+
+/* USB */
+#ifdef CONFIG_CMD_USB
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	2
+#else
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE		ATMEL_BASE_OHCI
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9x5"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	3
+#endif
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_STORAGE
+#endif
+

include/configs/cdu9g25.h line 188

Quoted 10 lines
include/configs/cdu9g25.h new file +10 -0
+#define CONFIG_SYS_LOAD_ADDR		0x21000000 /* load address */
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		CONFIG_SYS_TEXT_BASE
+
+/* CONFIG_SYS_USE_NANDFLASH */
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET	0x100000
+#define CONFIG_ENV_SIZE		0x10000 /* 1 sector = 128kB */

128kB = 0x20000

Quoted 16 lines
include/configs/cdu9g25.h new file +16 -0
+#define CONFIG_ENV_RANGE	0x20000 /* 2 sectors for bad sector handling */
+#define CONFIG_BOOTCOMMAND	"nand read 21000000 kernel; bootm"
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 ubi.mtd=root "\
+				"root=ubi0:root rootfstype=ubifs rw"
+#define CONFIG_SERVERIP		10.0.1.1
+#define CONFIG_BOOTFILE		"kernel_cdu9g25"
+#define CONFIG_PREBOOT		"mtdparts default" /* for partitions */
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)\
+				+ 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE

include/configs/cdu9g25.h line 214

Quoted 10 lines
include/configs/cdu9g25.h new file +10 -0
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024 + CONFIG_ENV_SIZE)
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif

No where define it, so no need this.

Quoted 3 lines
include/configs/cdu9g25.h new file +1 -1
+#endif
--

1.7.9.5

Best Regards,
Bo Shen