doc: README.mxs: Add instruction to install 'libssl-dev'
PATCH v3 1/1 doc: README.mxs: Add instruction to install 'libssl-dev'
Since commit bce883707 (ARM: mxs: tools: Add mkimage support for MXS bootstream) the following build error is seen when doing a MAKEALL build:
$ ./MAKEALL mx28evk Configuring for mx28evk - Board: mx28evk, Options: ENV_IS_IN_MMC mxsimage.c:18:25: fatal error: openssl/evp.h: No such file or directory
Add an entry about the need of installing the 'libssl-dev' package.
---
Changes since v2:
- Use "Debian-based"
Changes since v1:
- Do not remove the 'elftosb' text.
doc/README.mxs | 5 +++++ 1 file changed, 5 insertions(+)
doc/README.mxs +5 -0
@@ -63,6 +63,11 @@ copy the binary by hand: Make sure the "elftosb" binary can be found in your $PATH, in this case this means "/usr/local/bin/" has to be in your $PATH. +Install the 'libssl-dev' package as well. On a Debian-based distribution, this +package can be installed as follows: + + $ sudo apt-get install libssl-dev + 2) Compiling U-Boot for a MXS based board -------------------------------------------
Signature · 1 line
1.8.1.2
PATCH v3 1/1 doc: README.mxs: Add instruction to install 'libssl-dev'
Dear Fabio Estevam,
Quoted 29 lines
Since commit
bce883707(ARM: mxs: tools: Add mkimage support for MXS bootstream) the following build error is seen when doing a MAKEALL build:$ ./MAKEALL mx28evk Configuring for mx28evk - Board: mx28evk, Options: ENV_IS_IN_MMC mxsimage.c:18:25: fatal error: openssl/evp.h: No such file or directoryAdd an entry about the need of installing the 'libssl-dev' package.
Signed-off-by Fabio Estevam <[email protected]>---
Changes since v2:
- Use "Debian-based"
Changes since v1:
- Do not remove the 'elftosb' text.doc/README.mxs | 5 +++++ 1 file changed, 5 insertions(+)doc/README.mxs +0
-0@@ -63,6 +63,11 @@ copy the binary by hand: Make sure the "elftosb" binary can be found in your $PATH, in this casethis means "
/usr/local/bin/" has to be in your $PATH.+Install the 'libssl-dev' package as well. On a Debian-based distribution, this +package can be installed as follows:
doc/README.mxs copy the binary by hand: · line 72
Quoted 5 lines
doc/README.mxs +3
-0+ + $ sudo apt-get install libssl-dev + 2) Compiling U-Boot for a MXS based board -------------------------------------------
Best regards,
Marek Vasut
PATCH v3 1/1 doc: README.mxs: Add instruction to install 'libssl-dev'
In reply to Fabio EstevamQuoted 11 lines · Fabio Estevam
Since commit
bce883707(ARM: mxs: tools: Add mkimage support for MXS bootstream) the following build error is seen when doing a MAKEALL build:$ ./MAKEALL mx28evk Configuring for mx28evk - Board: mx28evk, Options: ENV_IS_IN_MMC mxsimage.c:18:25: fatal error: openssl/evp.h: No such file or directoryAdd an entry about the need of installing the 'libssl-dev' package.
Signed-off-by Fabio Estevam <[email protected]>---
Applied to u-boot-imx, thanks!
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================