Skip to contentSkip to conversation

arm64 patch

PATCH Superseded fenghua at phytium.com.cn 4 participants 12 messages Sep 26, 2013 – Oct 3, 2013

Subsystems (2)

v13 of 16 Superseded Latest is v16 →

lore
Share & tools
lore
#0 lore raw

v13 cover arm64 patch

From: David Feng <[email protected]>

Changes for v13:
- fix the bug of board_r.c and arm/lib/board.c due to CONFIG_NEED_MANUAL_RELOC. adjust initr_serial() in board_r.c
to the first entry of init_sequence_r[] and relocate serial_initialize() in arm/lib/board.c, routines of serial_device should be relocated firstly by serial_initialize(), so that printf access the correct puts function, otherwise uninitialized serial_current will be selected as the output device.
- fix the bug of dcache_enable(). after mmu_setup the sctrl
register value should be fetched again because it has been
modifed by mmu_seup() function. This bug is find by York Sun <[email protected]>.
- add macro branch_if_slave to macro.h, it choose processor
with all zero affinity value as the master and is used in start.S.

Changes for v12:
- custom the patches to new format boards.cfg.

Changes for v11:
- Replace CONFIG_ARMV8 with CONFIG_ARM64. Currently, it's hard to distinguish what is armv8 specific and what is aarch64 specific, so we use CONFIG_ARM64
only, no CONFIG_ARMV8 used.
- rename README.armv8 with README.arm64 and make some modification.

Changes for v10:
- add weak definition to include/linux/linkage.h and make setup_el2/setup_el3/lowlevel_init weak routines, so them can be easily overridden by processor specific code.
- modify s-o-f of 0002-board-support-of-vexpress_aemv8a which use wrong mail address of Bhupesh Sharma.

Changes for v9:
- add Signed-off-by information to patch "board support of vexpress_aemv8a" which SMC91111 support is integrated from Sharma Bhupesh's patch.
- adjust pt_regs struct and add exception state preservation in exception.S.

Changes for v8:
- Integrate SMC91111 patch of sharma bhupesh.
- remove v8_outer_cache* which is not need currently.
- Change license tag.
- Mov crt0.S/relocate.S/interrupts.c to arm/lib and rename them with _64 suffix.
- Make el3/el2 initializing process of start.S as two separate routines. It could be easier to be replaced with processor specific codes.
- Remove exception stack save and restore routine, it is unnecessary now.
- simplify __weak function declaration.

Changes for v7:
- Check the patches with checkpatch.pl and get rid of almost all warnings. There are a few warnings still, but I think it should be that.
- change printf format in cmd_pxe.c, use %zd indtead of %ld to format size_t type variable.
- add macro PGTABLE_SIZE to identify tlb table size.

Changes for v6:
- Make modification to inappropriate licensed file and bugs according to ScottWood's advice. Thanks Scott for his checking to these patches.
- Enable u-boot's running at EL1.
- Get rid of compiling warnings originated from cmd_pxe.c.

Changes for v5:
- fix the generic board_f.c, remove zero_global_data from init_sequence_f array and move it to board_init_f() function with CONFIG_X86 switch. The previous fixup is inaccurate.
- Replace __ARMEB__ with __AARCH64EB__ in byteorder.h and unaligned.h, gcc for aarch64 use __AARCH64EB__ and __AARCH64EL__ to identify endian.
- Some modification to README.armv8

Changes for v4:
- merge arm64 to arm architecture.

David Feng (6):
core support of arm64
board support of vexpress_aemv8a
generic board patch of manual reloc and zero gd_t 64bit initrd start address support
remove compiling warnings
add weak entry definition

 arch/arm/config.mk                      |    4 +
 arch/arm/cpu/armv8/Makefile             |   38 +++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 +++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 ++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++
 arch/arm/cpu/armv8/exceptions.S         |  115 ++++++++
 arch/arm/cpu/armv8/start.S              |  234 ++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 ++++++
 arch/arm/cpu/armv8/tlb.S                |   30 +++
 arch/arm/cpu/armv8/u-boot.lds           |   71 +++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 +
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 ++++++++
 arch/arm/include/asm/byteorder.h        |   12 +
 arch/arm/include/asm/cache.h            |    5 +
 arch/arm/include/asm/config.h           |   10 +
 arch/arm/include/asm/global_data.h      |    6 +-
 arch/arm/include/asm/io.h               |   15 +-
 arch/arm/include/asm/macro.h            |   39 +++
 arch/arm/include/asm/posix_types.h      |   10 +
 arch/arm/include/asm/proc-armv/ptrace.h |   21 ++
 arch/arm/include/asm/proc-armv/system.h |   59 ++++-
 arch/arm/include/asm/system.h           |   77 ++++++
 arch/arm/include/asm/types.h            |    4 +
 arch/arm/include/asm/u-boot.h           |    4 +
 arch/arm/include/asm/unaligned.h        |    2 +-
 arch/arm/lib/Makefile                   |   14 +
 arch/arm/lib/board.c                    |   25 +-
 arch/arm/lib/bootm.c                    |   16 ++
 arch/arm/lib/crt0_64.S                  |  116 ++++++++
 arch/arm/lib/interrupts_64.c            |  120 +++++++++
 arch/arm/lib/relocate_64.S              |   57 ++++
 board/armltd/dts/vexpress64.dts         |  439 +++++++++++++++++++++++++++++++
 board/armltd/vexpress64/Makefile        |   27 ++
 board/armltd/vexpress64/vexpress64.c    |   70 +++++
 boards.cfg                              |    1 +
 common/board_f.c                        |   18 +-
 common/board_r.c                        |   20 +-
 common/cmd_pxe.c                        |    4 +-
 common/fdt_support.c                    |   66 ++---
 common/image.c                          |    1 +
 doc/README.arm64                        |   33 +++
 examples/standalone/stubs.c             |   15 ++
 include/configs/vexpress_aemv8a.h       |  191 ++++++++++++++
 include/image.h                         |    1 +
 include/linux/linkage.h                 |    4 +
 46 files changed, 2573 insertions(+), 53 deletions(-)
 create mode 100644 arch/arm/cpu/armv8/Makefile
 create mode 100644 arch/arm/cpu/armv8/cache.S
 create mode 100644 arch/arm/cpu/armv8/cache_v8.c
 create mode 100644 arch/arm/cpu/armv8/config.mk
 create mode 100644 arch/arm/cpu/armv8/cpu.c
 create mode 100644 arch/arm/cpu/armv8/exceptions.S
 create mode 100644 arch/arm/cpu/armv8/start.S
 create mode 100644 arch/arm/cpu/armv8/timer.c
 create mode 100644 arch/arm/cpu/armv8/tlb.S
 create mode 100644 arch/arm/cpu/armv8/u-boot.lds
 create mode 100644 arch/arm/include/asm/arch-armv8/gpio.h
 create mode 100644 arch/arm/include/asm/arch-armv8/mmu.h
 create mode 100644 arch/arm/lib/crt0_64.S
 create mode 100644 arch/arm/lib/interrupts_64.c
 create mode 100644 arch/arm/lib/relocate_64.S
 create mode 100644 board/armltd/dts/vexpress64.dts
 create mode 100644 board/armltd/vexpress64/Makefile
 create mode 100644 board/armltd/vexpress64/vexpress64.c
 create mode 100644 doc/README.arm64
 create mode 100644 include/configs/vexpress_aemv8a.h
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v13 1/6 core support of arm64

From: David Feng <[email protected]>

---
 arch/arm/config.mk                      |    4 +
 arch/arm/cpu/armv8/Makefile             |   38 +++++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 ++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 +++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++++++
 arch/arm/cpu/armv8/exceptions.S         |  115 +++++++++++++++
 arch/arm/cpu/armv8/start.S              |  234 +++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 +++++++++++
 arch/arm/cpu/armv8/tlb.S                |   30 ++++
 arch/arm/cpu/armv8/u-boot.lds           |   71 ++++++++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 ++
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 +++++++++++++++
 arch/arm/include/asm/byteorder.h        |   12 ++
 arch/arm/include/asm/cache.h            |    5 +
 arch/arm/include/asm/config.h           |   10 ++
 arch/arm/include/asm/global_data.h      |    6 +-
 arch/arm/include/asm/io.h               |   15 +-
 arch/arm/include/asm/macro.h            |   39 ++++++
 arch/arm/include/asm/posix_types.h      |   10 ++
 arch/arm/include/asm/proc-armv/ptrace.h |   21 +++
 arch/arm/include/asm/proc-armv/system.h |   59 +++++++-
 arch/arm/include/asm/system.h           |   77 ++++++++++
 arch/arm/include/asm/types.h            |    4 +
 arch/arm/include/asm/u-boot.h           |    4 +
 arch/arm/include/asm/unaligned.h        |    2 +-
 arch/arm/lib/Makefile                   |   14 ++
 arch/arm/lib/board.c                    |   25 +++-
 arch/arm/lib/bootm.c                    |   16 +++
 arch/arm/lib/crt0_64.S                  |  116 +++++++++++++++
 arch/arm/lib/interrupts_64.c            |  120 ++++++++++++++++
 arch/arm/lib/relocate_64.S              |   57 ++++++++
 common/image.c                          |    1 +
 doc/README.arm64                        |   33 +++++
 examples/standalone/stubs.c             |   15 ++
 include/image.h                         |    1 +
 36 files changed, 1775 insertions(+), 11 deletions(-)
 create mode 100644 arch/arm/cpu/armv8/Makefile
 create mode 100644 arch/arm/cpu/armv8/cache.S
 create mode 100644 arch/arm/cpu/armv8/cache_v8.c
 create mode 100644 arch/arm/cpu/armv8/config.mk
 create mode 100644 arch/arm/cpu/armv8/cpu.c
 create mode 100644 arch/arm/cpu/armv8/exceptions.S
 create mode 100644 arch/arm/cpu/armv8/start.S
 create mode 100644 arch/arm/cpu/armv8/timer.c
 create mode 100644 arch/arm/cpu/armv8/tlb.S
 create mode 100644 arch/arm/cpu/armv8/u-boot.lds
 create mode 100644 arch/arm/include/asm/arch-armv8/gpio.h
 create mode 100644 arch/arm/include/asm/arch-armv8/mmu.h
 create mode 100644 arch/arm/lib/crt0_64.S
 create mode 100644 arch/arm/lib/interrupts_64.c
 create mode 100644 arch/arm/lib/relocate_64.S
 create mode 100644 doc/README.arm64
arch/arm/config.mk +4 -0
index ce3903b..95c07ad 100644
@@ -74,7 +74,9 @@ endif
 endif
 
 # needed for relocation
+ifndef CONFIG_ARM64
 LDFLAGS_u-boot += -pie
+endif
 
 #
 # FIXME: binutils versions < 2.22 have a bug in the assembler where
@@ -95,6 +97,8 @@ endif
 endif
 
 # check that only R_ARM_RELATIVE relocations are generated
+ifndef CONFIG_ARM64
 ifneq ($(CONFIG_SPL_BUILD),y)
 ALL-y	+= checkarmreloc
 endif
+endif
arch/arm/cpu/armv8/Makefile new file +38 -0
new file mode 100644
index 0000000..b216f27
@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(CPU).o
+
+START	:= start.o
+
+COBJS	+= cpu.o
+COBJS	+= timer.o
+COBJS	+= cache_v8.o
+
+SOBJS	+= exceptions.o
+SOBJS	+= cache.o
+SOBJS	+= tlb.o
+
+SRCS	:= $(START:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+START	:= $(addprefix $(obj),$(START))
+
+all:	$(obj).depend $(START) $(LIB)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
arch/arm/cpu/armv8/cache.S new file +130 -0

130 lines not on this page · raw message

arch/arm/cpu/armv8/cache_v8.c new file +218 -0

218 lines not on this page · raw message

arch/arm/cpu/armv8/config.mk new file +16 -0
new file mode 100644
index 0000000..9f36d59
@@ -0,0 +1,16 @@
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+PLATFORM_RELFLAGS += -fno-common -ffixed-x18
+
+# SEE README.arm-unaligned-accesses
+PF_NO_UNALIGNED := $(call cc-option, -mstrict-align)
+PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
+
+PF_CPPFLAGS_ARMV8 := $(call cc-option, -march=armv8-a)
+PLATFORM_CPPFLAGS += $(PF_CPPFLAGS_ARMV8)
+PLATFORM_CPPFLAGS += $(PF_NO_UNALIGNED)
+PLATFORM_CPPFLAGS += -fpic
arch/arm/cpu/armv8/cpu.c new file +67 -0

67 lines not on this page · raw message

arch/arm/cpu/armv8/exceptions.S new file +115 -0

115 lines not on this page · raw message

arch/arm/cpu/armv8/start.S new file +234 -0

234 lines not on this page · raw message

arch/arm/cpu/armv8/timer.c new file +80 -0

80 lines not on this page · raw message

arch/arm/cpu/armv8/tlb.S new file +30 -0
new file mode 100644
index 0000000..6bb1e1f
@@ -0,0 +1,30 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <version.h>
+#include <linux/linkage.h>
+#include <asm/macro.h>
+
+/*
+ * void __asm_invalidate_tlb_all(void)
+ *
+ * invalidate all tlb entries.
+ */
+ENTRY(__asm_invalidate_tlb_all)
+	switch_el1_el2 x9, 1f, 2f, 3f
+1:	tlbi	vmalle1
+	dsb	sy
+	isb
+	b	3f
+2:	tlbi	alle2
+	dsb	sy
+	isb
+3:
+	ret
+ENDPROC(__asm_invalidate_tlb_all)
arch/arm/cpu/armv8/u-boot.lds new file +71 -0

71 lines not on this page · raw message

arch/arm/include/asm/arch-armv8/gpio.h new file +11 -0
new file mode 100644
index 0000000..afe7ece
@@ -0,0 +1,11 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _ASM_ARMV8_GPIO_H_
+#define _ASM_ARMV8_GPIO_H_
+
+#endif	/* _ASM_ARMV8_GPIO_H_ */
arch/arm/include/asm/arch-armv8/mmu.h new file +110 -0

110 lines not on this page · raw message

arch/arm/include/asm/byteorder.h +12 -0
index c3489f1..71a9966 100644
@@ -23,10 +23,22 @@
 #  define __SWAB_64_THRU_32__
 #endif
 
+#ifdef	CONFIG_ARM64
+
+#ifdef __AARCH64EB__
+#include <linux/byteorder/big_endian.h>
+#else
+#include <linux/byteorder/little_endian.h>
+#endif
+
+#else	/* CONFIG_ARM64 */
+
 #ifdef __ARMEB__
 #include <linux/byteorder/big_endian.h>
 #else
 #include <linux/byteorder/little_endian.h>
 #endif
 
+#endif	/* CONFIG_ARM64 */
+
 #endif
arch/arm/include/asm/cache.h +5 -0
index 6d60a4a..ddebbc8 100644
@@ -11,6 +11,8 @@
 
 #include <asm/system.h>
 
+#ifndef CONFIG_ARM64
+
 /*
  * Invalidate L2 Cache using co-proc instruction
  */
@@ -28,6 +30,9 @@ void l2_cache_disable(void);
 void set_section_dcache(int section, enum dcache_option option);
 
 void dram_bank_mmu_setup(int bank);
+
+#endif
+
 /*
  * The current upper bound for ARM L1 data cache line sizes is 64 bytes.  We
  * use that value for aligning DMA buffers unless the board config has specified
arch/arm/include/asm/config.h +10 -0
index 99b703e..0ee131d 100644
@@ -9,4 +9,14 @@
 
 #define CONFIG_LMB
 #define CONFIG_SYS_BOOT_RAMDISK_HIGH
+
+#ifdef CONFIG_ARM64
+/*
+ * Currently, GOT is used to relocate u-boot and
+ * configuration CONFIG_NEEDS_MANUAL_RELOC is needed.
+ */
+#define CONFIG_NEEDS_MANUAL_RELOC
+#define CONFIG_PHYS_64BIT
+#endif
+
 #endif
arch/arm/include/asm/global_data.h +5 -1
index 79a9597..30a338e 100644
@@ -47,6 +47,10 @@ struct arch_global_data {
 
 #include <asm-generic/global_data.h>
 
-#define DECLARE_GLOBAL_DATA_PTR     register volatile gd_t *gd asm ("r8")
+#ifdef CONFIG_ARM64
+#define DECLARE_GLOBAL_DATA_PTR		register volatile gd_t *gd asm ("x18")
+#else
+#define DECLARE_GLOBAL_DATA_PTR		register volatile gd_t *gd asm ("r8")
+#endif
 
 #endif /* __ASM_GBL_DATA_H */
arch/arm/include/asm/io.h +9 -6
index 1fbc531..6a1f05a 100644
@@ -75,42 +75,45 @@ static inline phys_addr_t virt_to_phys(void * vaddr)
 #define __arch_putw(v,a)		(*(volatile unsigned short *)(a) = (v))
 #define __arch_putl(v,a)		(*(volatile unsigned int *)(a) = (v))
 
-extern inline void __raw_writesb(unsigned int addr, const void *data, int bytelen)
+extern inline void __raw_writesb(unsigned long addr, const void *data,
+				 int bytelen)
 {
 	uint8_t *buf = (uint8_t *)data;
 	while(bytelen--)
 		__arch_putb(*buf++, addr);
 }
 
-extern inline void __raw_writesw(unsigned int addr, const void *data, int wordlen)
+extern inline void __raw_writesw(unsigned long addr, const void *data,
+				 int wordlen)
 {
 	uint16_t *buf = (uint16_t *)data;
 	while(wordlen--)
 		__arch_putw(*buf++, addr);
 }
 
-extern inline void __raw_writesl(unsigned int addr, const void *data, int longlen)
+extern inline void __raw_writesl(unsigned long addr, const void *data,
+				 int longlen)
 {
 	uint32_t *buf = (uint32_t *)data;
 	while(longlen--)
 		__arch_putl(*buf++, addr);
 }
 
-extern inline void __raw_readsb(unsigned int addr, void *data, int bytelen)
+extern inline void __raw_readsb(unsigned long addr, void *data, int bytelen)
 {
 	uint8_t *buf = (uint8_t *)data;
 	while(bytelen--)
 		*buf++ = __arch_getb(addr);
 }
 
-extern inline void __raw_readsw(unsigned int addr, void *data, int wordlen)
+extern inline void __raw_readsw(unsigned long addr, void *data, int wordlen)
 {
 	uint16_t *buf = (uint16_t *)data;
 	while(wordlen--)
 		*buf++ = __arch_getw(addr);
 }
 
-extern inline void __raw_readsl(unsigned int addr, void *data, int longlen)
+extern inline void __raw_readsl(unsigned long addr, void *data, int longlen)
 {
 	uint32_t *buf = (uint32_t *)data;
 	while(longlen--)
arch/arm/include/asm/macro.h +39 -0
index ff13f36..db8869e 100644
@@ -54,5 +54,44 @@
 	bcs	1b
 .endm
 
+#ifdef CONFIG_ARM64
+/*
+ * Register aliases.
+ */
+lr	.req	x30
+
+/*
+ * Branch according to exception level
+ */
+.macro	switch_el1_el2, xreg, el1_label, el2_label, fail_label
+	mrs	\xreg, CurrentEL
+	cmp	\xreg, 0x4
+	b.eq	\el1_label
+	cmp	\xreg, 0x8
+	b.eq	\el2_label
+	b	\fail_label
+.endm
+
+/*
+ * Branch if current processor is a slave,
+ * choose processor with all zero affinity value as the master.
+ */
+.macro	branch_if_slave, xreg, slave_label
+	mrs	\xreg, mpidr_el1
+	tst	\xreg, #0xff		/* Test Affinity 0 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #8
+	tst	\xreg, #0xff		/* Test Affinity 1 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #8
+	tst	\xreg, #0xff		/* Test Affinity 2 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #16
+	tst	\xreg, #0xff		/* Test Affinity 3 */
+	b.ne	\slave_label
+.endm
+
+#endif /* CONFIG_ARM64 */
+
 #endif /* __ASSEMBLY__ */
 #endif /* __ASM_ARM_MACRO_H__ */
arch/arm/include/asm/posix_types.h +10 -0
index c412486..9ba9add 100644
@@ -13,6 +13,8 @@
 #ifndef __ARCH_ARM_POSIX_TYPES_H
 #define __ARCH_ARM_POSIX_TYPES_H
 
+#include <config.h>
+
 /*
  * This file is generally used by user-level software, so you need to
  * be a little careful about namespace pollution etc.  Also, we cannot
@@ -28,9 +30,17 @@ typedef int			__kernel_pid_t;
 typedef unsigned short		__kernel_ipc_pid_t;
 typedef unsigned short		__kernel_uid_t;
 typedef unsigned short		__kernel_gid_t;
+
+#ifdef	CONFIG_ARM64
+typedef unsigned long		__kernel_size_t;
+typedef long			__kernel_ssize_t;
+typedef long			__kernel_ptrdiff_t;
+#else	/* CONFIG_ARM64 */
 typedef unsigned int		__kernel_size_t;
 typedef int			__kernel_ssize_t;
 typedef int			__kernel_ptrdiff_t;
+#endif	/* CONFIG_ARM64 */
+
 typedef long			__kernel_time_t;
 typedef long			__kernel_suseconds_t;
 typedef long			__kernel_clock_t;
arch/arm/include/asm/proc-armv/ptrace.h +21 -0
index 79cc644..fd280cb 100644
@@ -12,6 +12,25 @@
 
 #include <linux/config.h>
 
+#ifdef CONFIG_ARM64
+
+#define PCMASK		0
+
+#ifndef __ASSEMBLY__
+
+/*
+ * This struct defines the way the registers are stored
+ * on the stack during an exception.
+ */
+struct pt_regs {
+	unsigned long elr;
+	unsigned long regs[31];
+};
+
+#endif	/* __ASSEMBLY__ */
+
+#else	/* CONFIG_ARM64 */
+
 #define USR26_MODE	0x00
 #define FIQ26_MODE	0x01
 #define IRQ26_MODE	0x02
@@ -106,4 +125,6 @@ static inline int valid_user_regs(struct pt_regs *regs)
 
 #endif	/* __ASSEMBLY__ */
 
+#endif	/* CONFIG_ARM64 */
+
 #endif
arch/arm/include/asm/proc-armv/system.h +58 -1

71 lines not on this page · raw message

arch/arm/include/asm/system.h +77 -0

93 lines not on this page · raw message

arch/arm/include/asm/types.h +4 -0
index 71dc049..2326420 100644
@@ -39,7 +39,11 @@ typedef unsigned int u32;
 typedef signed long long s64;
 typedef unsigned long long u64;
 
+#ifdef	CONFIG_ARM64
+#define BITS_PER_LONG 64
+#else	/* CONFIG_ARM64 */
 #define BITS_PER_LONG 32
+#endif	/* CONFIG_ARM64 */
 
 /* Dma addresses are 32-bits wide.  */
 
arch/arm/include/asm/u-boot.h +4 -0
index 2b5fce8..cb81232 100644
@@ -44,6 +44,10 @@ typedef struct bd_info {
 #endif /* !CONFIG_SYS_GENERIC_BOARD */
 
 /* For image.h:image_check_target_arch() */
+#ifndef CONFIG_ARM64
 #define IH_ARCH_DEFAULT IH_ARCH_ARM
+#else
+#define IH_ARCH_DEFAULT IH_ARCH_ARM64
+#endif
 
 #endif	/* _U_BOOT_H_ */
arch/arm/include/asm/unaligned.h +1 -1
index 44593a8..0a228fb 100644
@@ -8,7 +8,7 @@
 /*
  * Select endianness
  */
-#ifndef __ARMEB__
+#if __BYTE_ORDER == __LITTLE_ENDIAN
 #define get_unaligned	__get_unaligned_le
 #define put_unaligned	__put_unaligned_le
 #else
arch/arm/lib/Makefile +14 -0
index 4e78723..03c31c7 100644
@@ -10,6 +10,9 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(ARCH).o
 LIBGCC	= $(obj)libgcc.o
 
+ifdef CONFIG_ARM64
+SOBJS-y += crt0_64.o
+else
 GLSOBJS	+= _ashldi3.o
 GLSOBJS	+= _ashrdi3.o
 GLSOBJS	+= _divsi3.o
@@ -21,9 +24,14 @@ GLSOBJS	+= _umodsi3.o
 GLCOBJS	+= div0.o
 
 SOBJS-y += crt0.o
+endif
 
 ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_ARM64
+SOBJS-y += relocate_64.o
+else
 SOBJS-y += relocate.o
+endif
 ifndef CONFIG_SYS_GENERIC_BOARD
 COBJS-y	+= board.o
 endif
@@ -38,11 +46,17 @@ else
 COBJS-$(CONFIG_SPL_FRAMEWORK) += spl.o
 endif
 
+ifdef CONFIG_ARM64
+COBJS-y	+= interrupts_64.o
+else
 COBJS-y	+= interrupts.o
+endif
 COBJS-y	+= reset.o
 
 COBJS-y	+= cache.o
+ifndef CONFIG_ARM64
 COBJS-y	+= cache-cp15.o
+endif
 
 SRCS	:= $(GLSOBJS:.o=.S) $(GLCOBJS:.o=.c) \
 	   $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
arch/arm/lib/board.c +23 -2
index 34f50b0..d6d0833 100644
@@ -344,7 +344,7 @@ void board_init_f(ulong bootflag)
 
 #if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
 	/* reserve TLB table */
-	gd->arch.tlb_size = 4096 * 4;
+	gd->arch.tlb_size = PGTABLE_SIZE;
 	addr -= gd->arch.tlb_size;
 
 	/* round down to next 64 kB limit */
@@ -419,6 +419,7 @@ void board_init_f(ulong bootflag)
 	}
 #endif
 
+#ifndef CONFIG_ARM64
 	/* setup stackpointer for exeptions */
 	gd->irq_sp = addr_sp;
 #ifdef CONFIG_USE_IRQ
@@ -431,6 +432,10 @@ void board_init_f(ulong bootflag)
 
 	/* 8-byte alignment for ABI compliance */
 	addr_sp &= ~0x07;
+#else	/* CONFIG_ARM64 */
+	/* 16-byte alignment for ABI compliance */
+	addr_sp &= ~0x0f;
+#endif	/* CONFIG_ARM64 */
 #else
 	addr_sp += 128;	/* leave 32 words for abort-stack   */
 	gd->irq_sp = addr_sp;
@@ -513,7 +518,15 @@ void board_init_r(gd_t *id, ulong dest_addr)
 	ulong flash_size;
 #endif
 
+	/*
+	 * Relocate routines of serial_device first so that
+	 * printf access the correct puts function. This is critical
+	 * when CONFIG_NEEDS_MANUAL_RELOC is needed.
+	 */
+	serial_initialize();
+
 	gd->flags |= GD_FLG_RELOC;	/* tell others: relocation done */
+
 	bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
 
 	monitor_flash_len = _end_ofs;
@@ -523,6 +536,15 @@ void board_init_r(gd_t *id, ulong dest_addr)
 
 	debug("monitor flash len: %08lX\n", monitor_flash_len);
 	board_init();	/* Setup chipselects */
+
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+	/*
+	 * We have to relocate the command table manually
+	 */
+	fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd),
+			ll_entry_count(cmd_tbl_t, cmd));
+#endif /* CONFIG_NEEDS_MANUAL_RELOC */
+
 	/*
 	 * TODO: printing of the clock inforamtion of the board is now
 	 * implemented as part of bdinfo command. Currently only support for
@@ -532,7 +554,6 @@ void board_init_r(gd_t *id, ulong dest_addr)
 #ifdef CONFIG_CLOCKS
 	set_cpu_clk_info(); /* Setup clock information */
 #endif
-	serial_initialize();
 
 	debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
 
arch/arm/lib/bootm.c +16 -0
index eefb456..26e85f0 100644
@@ -222,6 +222,21 @@ static void boot_prep_linux(bootm_headers_t *images)
 /* Subcommand: GO */
 static void boot_jump_linux(bootm_headers_t *images, int flag)
 {
+#ifdef CONFIG_ARM64
+	void (*kernel_entry)(void *fdt_addr);
+	int fake = (flag & BOOTM_STATE_OS_FAKE_GO);
+
+	kernel_entry = (void (*)(void *fdt_addr))images->ep;
+
+	debug("## Transferring control to Linux (at address %lx)...\n",
+		(ulong) kernel_entry);
+	bootstage_mark(BOOTSTAGE_ID_RUN_OS);
+
+	announce_and_cleanup(fake);
+
+	if (!fake)
+		kernel_entry(images->ft_addr);
+#else
 	unsigned long machid = gd->bd->bi_arch_number;
 	char *s;
 	void (*kernel_entry)(int zero, int arch, uint params);
@@ -248,6 +263,7 @@ static void boot_jump_linux(bootm_headers_t *images, int flag)
 
 	if (!fake)
 		kernel_entry(0, machid, r2);
+#endif
 }
 
 /* Main Entry point for arm bootm implementation
arch/arm/lib/crt0_64.S new file +116 -0

116 lines not on this page · raw message

arch/arm/lib/interrupts_64.c new file +120 -0

120 lines not on this page · raw message

arch/arm/lib/relocate_64.S new file +57 -0

57 lines not on this page · raw message

common/image.c +1 -0
index b0ae58f..4145354 100644
@@ -81,6 +81,7 @@ static const table_entry_t uimage_arch[] = {
 	{	IH_ARCH_NDS32,		"nds32",	"NDS32",	},
 	{	IH_ARCH_OPENRISC,	"or1k",		"OpenRISC 1000",},
 	{	IH_ARCH_SANDBOX,	"sandbox",	"Sandbox",	},
+	{	IH_ARCH_ARM64,		"arm64",	"AArch64",	},
 	{	-1,			"",		"",		},
 };
 
doc/README.arm64 new file +33 -0
new file mode 100644
index 0000000..746ce6a
@@ -0,0 +1,33 @@
+U-boot for arm64
+
+Summary
+=======
+No hardware platform of arm64 is available now. The u-boot is
+simulated on Foundation Model and Fast Model for ARMv8.
+
+Notes
+=====
+
+1. Currenly, u-boot could be running at EL1 or EL2.
+
+2. Currenly, U-boot for arm64 is compiled with AArch64-gcc. AArch64-gcc
+   use rela relocation format, it cannot be relocated during running. So,
+   GOT is used to relocate u-boot and CONFIG_NEEDS_MANUAL_RELOC is needed.
+
+3. Fdt should be placed at a 2-megabyte boundary and within the first 512
+   megabytes from the start of the kernel image. So, fdt_high should be
+   defined specially.
+   Please reference linux/Documentation/arm64/booting.txt for detail.
+
+4. Generic board is supported.
+
+5. CONFIG_ARM64 instead of CONFIG_ARMV8 is used to distinguish aarch64 and
+   aarch32 specific codes.
+
+Contributor
+===========
+   Tom Rini       <[email protected]>
+   Scott Wood     <[email protected]>
+   Simon Glass    <[email protected]>
+   Sharma Bhupesh <[email protected]>
+   Rob Herring    <[email protected]>
examples/standalone/stubs.c +15 -0
index 8fb1765..fc5d7ef 100644
@@ -39,6 +39,20 @@ gd_t *global_data;
 "	bctr\n"				\
 	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "r11");
 #elif defined(CONFIG_ARM)
+#ifdef CONFIG_ARM64
+/*
+ * x18 holds the pointer to the global_data, x9 is a call-clobbered
+ * register
+ */
+#define EXPORT_FUNC(x) \
+	asm volatile (			\
+"	.globl " #x "\n"		\
+#x ":\n"				\
+"	ldr	x9, [x18, %0]\n"		\
+"	ldr	x9, [x9, %1]\n"		\
+"	br	x9\n"		\
+	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "x9");
+#else
 /*
  * r8 holds the pointer to the global_data, ip is a call-clobbered
  * register
@@ -50,6 +64,7 @@ gd_t *global_data;
 "	ldr	ip, [r8, %0]\n"		\
 "	ldr	pc, [ip, %1]\n"		\
 	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "ip");
+#endif
 #elif defined(CONFIG_MIPS)
 /*
  * k0 ($26) holds the pointer to the global_data; t9 ($25) is a call-
include/image.h +1 -0
index ee6eb8d..7de2bb2 100644
@@ -156,6 +156,7 @@ struct lmb;
 #define IH_ARCH_SANDBOX		19	/* Sandbox architecture (test only) */
 #define IH_ARCH_NDS32	        20	/* ANDES Technology - NDS32  */
 #define IH_ARCH_OPENRISC        21	/* OpenRISC 1000  */
+#define IH_ARCH_ARM64		22	/* ARM64	*/
 
 /*
  * Image Types
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH v13 2/6 board support of vexpress_aemv8a

From: David Feng <[email protected]>

---
 board/armltd/dts/vexpress64.dts      |  439 ++++++++++++++++++++++++++++++++++
 board/armltd/vexpress64/Makefile     |   27 +++
 board/armltd/vexpress64/vexpress64.c |   70 ++++++
 boards.cfg                           |    1 +
 include/configs/vexpress_aemv8a.h    |  191 +++++++++++++++
 5 files changed, 728 insertions(+)
 create mode 100644 board/armltd/dts/vexpress64.dts
 create mode 100644 board/armltd/vexpress64/Makefile
 create mode 100644 board/armltd/vexpress64/vexpress64.c
 create mode 100644 include/configs/vexpress_aemv8a.h
board/armltd/dts/vexpress64.dts new file +439 -0
new file mode 100644
index 0000000..067fea7
@@ -0,0 +1,439 @@
+/*
+ * ARM Ltd. Fast Models
+ *
+ * Architecture Envelope Model (AEM) ARMv8-A
+ * ARMAEMv8AMPCT
+ *
+ * RTSM_VE_AEMv8A.lisa
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x80000000 0x00010000;
+
+/ {
+	/* boot configurations for u-boot */
+	config {
+		/*bootdelay = <1>;*/
+		kernel-offset = <0x100000>;
+		rootdisk-offset = <0x800000>;
+		bootcmd = "bootm 0x100000 0x800000:0x2000000";
+	};
+};
+
+/ {
+	model = "RTSM_VE_AEMv8A";
+	compatible = "arm,rtsm_ve,aemv8a", "arm,vexpress";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/* chosen */
+	/* generated by u-boot */
+
+
+	aliases {
+		serial0 = &v2m_serial0;
+		serial1 = &v2m_serial1;
+		serial2 = &v2m_serial2;
+		serial3 = &v2m_serial3;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x8000fff8>;
+		};
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x8000fff8>;
+		};
+		cpu at 2 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x8000fff8>;
+		};
+		cpu at 3 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x8000fff8>;
+		};
+	};
+
+	memory at 80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x80000000>,
+		      <0x00000008 0x80000000 0 0x80000000>;
+	};
+
+	gic: interrupt-controller at 2c001000 {
+		compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x0 0x2c001000 0 0x1000>,
+		      <0x0 0x2c002000 0 0x1000>,
+		      <0x0 0x2c004000 0 0x2000>,
+		      <0x0 0x2c006000 0 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <1 13 0xff01>,
+			     <1 14 0xff01>,
+			     <1 11 0xff01>,
+			     <1 10 0xff01>;
+		clock-frequency = <100000000>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <0 60 4>,
+			     <0 61 4>,
+			     <0 62 4>,
+			     <0 63 4>;
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x08000000 0x04000000>,
+			 <1 0 0 0x14000000 0x04000000>,
+			 <2 0 0 0x18000000 0x04000000>,
+			 <3 0 0 0x1c000000 0x04000000>,
+			 <4 0 0 0x0c000000 0x04000000>,
+			 <5 0 0 0x10000000 0x04000000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 63>;
+		interrupt-map = <0 0  0 &gic 0  0 4>,
+				<0 0  1 &gic 0  1 4>,
+				<0 0  2 &gic 0  2 4>,
+				<0 0  3 &gic 0  3 4>,
+				<0 0  4 &gic 0  4 4>,
+				<0 0  5 &gic 0  5 4>,
+				<0 0  6 &gic 0  6 4>,
+				<0 0  7 &gic 0  7 4>,
+				<0 0  8 &gic 0  8 4>,
+				<0 0  9 &gic 0  9 4>,
+				<0 0 10 &gic 0 10 4>,
+				<0 0 11 &gic 0 11 4>,
+				<0 0 12 &gic 0 12 4>,
+				<0 0 13 &gic 0 13 4>,
+				<0 0 14 &gic 0 14 4>,
+				<0 0 15 &gic 0 15 4>,
+				<0 0 16 &gic 0 16 4>,
+				<0 0 17 &gic 0 17 4>,
+				<0 0 18 &gic 0 18 4>,
+				<0 0 19 &gic 0 19 4>,
+				<0 0 20 &gic 0 20 4>,
+				<0 0 21 &gic 0 21 4>,
+				<0 0 22 &gic 0 22 4>,
+				<0 0 23 &gic 0 23 4>,
+				<0 0 24 &gic 0 24 4>,
+				<0 0 25 &gic 0 25 4>,
+				<0 0 26 &gic 0 26 4>,
+				<0 0 27 &gic 0 27 4>,
+				<0 0 28 &gic 0 28 4>,
+				<0 0 29 &gic 0 29 4>,
+				<0 0 30 &gic 0 30 4>,
+				<0 0 31 &gic 0 31 4>,
+				<0 0 32 &gic 0 32 4>,
+				<0 0 33 &gic 0 33 4>,
+				<0 0 34 &gic 0 34 4>,
+				<0 0 35 &gic 0 35 4>,
+				<0 0 36 &gic 0 36 4>,
+				<0 0 37 &gic 0 37 4>,
+				<0 0 38 &gic 0 38 4>,
+				<0 0 39 &gic 0 39 4>,
+				<0 0 40 &gic 0 40 4>,
+				<0 0 41 &gic 0 41 4>,
+				<0 0 42 &gic 0 42 4>;
+
+		motherboard {
+			arm,v2m-memory-map = "rs1";
+			compatible = "arm,vexpress,v2m-p1", "simple-bus";
+			#address-cells = <2>; /* SMB chipselect number and offset */
+			#size-cells = <1>;
+			#interrupt-cells = <1>;
+			ranges;
+
+			flash at 0,00000000 {
+				compatible = "arm,vexpress-flash", "cfi-flash";
+				reg = <0 0x00000000 0x04000000>,
+				      <4 0x00000000 0x04000000>;
+				bank-width = <4>;
+			};
+
+			vram at 2,00000000 {
+				compatible = "arm,vexpress-vram";
+				reg = <2 0x00000000 0x00800000>;
+			};
+
+			ethernet at 2,02000000 {
+				compatible = "smsc,lan91c111";
+				reg = <2 0x02000000 0x10000>;
+				interrupts = <15>;
+			};
+
+			v2m_clk24mhz: clk24mhz {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <24000000>;
+				clock-output-names = "v2m:clk24mhz";
+			};
+
+			v2m_refclk1mhz: refclk1mhz {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <1000000>;
+				clock-output-names = "v2m:refclk1mhz";
+			};
+
+			v2m_refclk32khz: refclk32khz {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <32768>;
+				clock-output-names = "v2m:refclk32khz";
+			};
+
+			iofpga at 3,00000000 {
+				compatible = "arm,amba-bus", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 3 0 0x200000>;
+
+				v2m_sysreg: sysreg at 010000 {
+					compatible = "arm,vexpress-sysreg";
+					reg = <0x010000 0x1000>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				v2m_sysctl: sysctl at 020000 {
+					compatible = "arm,sp810", "arm,primecell";
+					reg = <0x020000 0x1000>;
+					clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&v2m_clk24mhz>;
+					clock-names = "refclk", "timclk", "apb_pclk";
+					#clock-cells = <1>;
+					clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
+				};
+
+				aaci at 040000 {
+					compatible = "arm,pl041", "arm,primecell";
+					reg = <0x040000 0x1000>;
+					interrupts = <11>;
+					clocks = <&v2m_clk24mhz>;
+					clock-names = "apb_pclk";
+				};
+
+				mmci at 050000 {
+					compatible = "arm,pl180", "arm,primecell";
+					reg = <0x050000 0x1000>;
+					interrupts = <9 10>;
+					cd-gpios = <&v2m_sysreg 0 0>;
+					wp-gpios = <&v2m_sysreg 1 0>;
+					max-frequency = <12000000>;
+					vmmc-supply = <&v2m_fixed_3v3>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "mclk", "apb_pclk";
+				};
+
+				kmi at 060000 {
+					compatible = "arm,pl050", "arm,primecell";
+					reg = <0x060000 0x1000>;
+					interrupts = <12>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "KMIREFCLK", "apb_pclk";
+				};
+
+				kmi at 070000 {
+					compatible = "arm,pl050", "arm,primecell";
+					reg = <0x070000 0x1000>;
+					interrupts = <13>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "KMIREFCLK", "apb_pclk";
+				};
+
+				v2m_serial0: uart at 090000 {
+					compatible = "arm,pl011", "arm,primecell";
+					reg = <0x090000 0x1000>;
+					interrupts = <5>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "uartclk", "apb_pclk";
+				};
+
+				v2m_serial1: uart at 0a0000 {
+					compatible = "arm,pl011", "arm,primecell";
+					reg = <0x0a0000 0x1000>;
+					interrupts = <6>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "uartclk", "apb_pclk";
+				};
+
+				v2m_serial2: uart at 0b0000 {
+					compatible = "arm,pl011", "arm,primecell";
+					reg = <0x0b0000 0x1000>;
+					interrupts = <7>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "uartclk", "apb_pclk";
+				};
+
+				v2m_serial3: uart at 0c0000 {
+					compatible = "arm,pl011", "arm,primecell";
+					reg = <0x0c0000 0x1000>;
+					interrupts = <8>;
+					clocks = <&v2m_clk24mhz>, <&v2m_clk24mhz>;
+					clock-names = "uartclk", "apb_pclk";
+				};
+
+				wdt at 0f0000 {
+					compatible = "arm,sp805", "arm,primecell";
+					reg = <0x0f0000 0x1000>;
+					interrupts = <0>;
+					clocks = <&v2m_refclk32khz>, <&v2m_clk24mhz>;
+					clock-names = "wdogclk", "apb_pclk";
+				};
+
+				v2m_timer01: timer at 110000 {
+					compatible = "arm,sp804", "arm,primecell";
+					reg = <0x110000 0x1000>;
+					interrupts = <2>;
+					clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_clk24mhz>;
+					clock-names = "timclken1", "timclken2", "apb_pclk";
+				};
+
+				v2m_timer23: timer at 120000 {
+					compatible = "arm,sp804", "arm,primecell";
+					reg = <0x120000 0x1000>;
+					interrupts = <3>;
+					clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&v2m_clk24mhz>;
+					clock-names = "timclken1", "timclken2", "apb_pclk";
+				};
+
+				rtc at 170000 {
+					compatible = "arm,pl031", "arm,primecell";
+					reg = <0x170000 0x1000>;
+					interrupts = <4>;
+					clocks = <&v2m_clk24mhz>;
+					clock-names = "apb_pclk";
+				};
+
+				clcd at 1f0000 {
+					compatible = "arm,pl111", "arm,primecell";
+					reg = <0x1f0000 0x1000>;
+					interrupts = <14>;
+					clocks = <&v2m_oscclk1>, <&v2m_clk24mhz>;
+					clock-names = "clcdclk", "apb_pclk";
+				};
+			};
+
+			v2m_fixed_3v3: fixedregulator at 0 {
+				compatible = "regulator-fixed";
+				regulator-name = "3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			mcc {
+				compatible = "arm,vexpress,config-bus", "simple-bus";
+				arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+				v2m_oscclk1: osc at 1 {
+					/* CLCD clock */
+					compatible = "arm,vexpress-osc";
+					arm,vexpress-sysreg,func = <1 1>;
+					freq-range = <23750000 63500000>;
+					#clock-cells = <0>;
+					clock-output-names = "v2m:oscclk1";
+				};
+
+				reset at 0 {
+					compatible = "arm,vexpress-reset";
+					arm,vexpress-sysreg,func = <5 0>;
+				};
+
+				muxfpga at 0 {
+					compatible = "arm,vexpress-muxfpga";
+					arm,vexpress-sysreg,func = <7 0>;
+				};
+
+				shutdown at 0 {
+					compatible = "arm,vexpress-shutdown";
+					arm,vexpress-sysreg,func = <8 0>;
+				};
+
+				reboot at 0 {
+					compatible = "arm,vexpress-reboot";
+					arm,vexpress-sysreg,func = <9 0>;
+				};
+
+				dvimode at 0 {
+					compatible = "arm,vexpress-dvimode";
+					arm,vexpress-sysreg,func = <11 0>;
+				};
+			};
+		};
+	};
+
+	panels {
+		panel at 0 {
+			compatible	= "panel";
+			mode		= "VGA";
+			refresh		= <60>;
+			xres		= <640>;
+			yres		= <480>;
+			pixclock	= <39721>;
+			left_margin	= <40>;
+			right_margin	= <24>;
+			upper_margin	= <32>;
+			lower_margin	= <11>;
+			hsync_len	= <96>;
+			vsync_len	= <2>;
+			sync		= <0>;
+			vmode		= "FB_VMODE_NONINTERLACED";
+			tim2		= "TIM2_BCD", "TIM2_IPC";
+			cntl		= "CNTL_LCDTFT", "CNTL_BGR", "CNTL_LCDVCOMP(1)";
+			caps		= "CLCD_CAP_5551", "CLCD_CAP_565", "CLCD_CAP_888";
+			bpp		= <16>;
+		};
+
+		panel at 1 {
+			compatible	= "panel";
+			mode		= "XVGA";
+			refresh		= <60>;
+			xres		= <1024>;
+			yres		= <768>;
+			pixclock	= <15748>;
+			left_margin	= <152>;
+			right_margin	= <48>;
+			upper_margin	= <23>;
+			lower_margin	= <3>;
+			hsync_len	= <104>;
+			vsync_len	= <4>;
+			sync		= <0>;
+			vmode		= "FB_VMODE_NONINTERLACED";
+			tim2		= "TIM2_BCD", "TIM2_IPC";
+			cntl		= "CNTL_LCDTFT", "CNTL_BGR", "CNTL_LCDVCOMP(1)";
+			caps		= "CLCD_CAP_5551", "CLCD_CAP_565", "CLCD_CAP_888";
+			bpp		= <16>;
+		};
+	};
+};
board/armltd/vexpress64/Makefile new file +27 -0
new file mode 100644
index 0000000..f907c92
@@ -0,0 +1,27 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= vexpress64.o
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/armltd/vexpress64/vexpress64.c new file +70 -0

70 lines not on this page · raw message

boards.cfg +1 -0
index 9fc77fb..d66bd46 100644
@@ -380,6 +380,7 @@ Active  arm         pxa            -           -               vpac270
 Active  arm         pxa            -           icpdas          lp8x4x              lp8x4x                               -                                                                                                                                 Sergey Yanovich <[email protected]>
 Active  arm         pxa            -           toradex         -                   colibri_pxa270                       -                                                                                                                                 Marek Vasut <[email protected]>
 Active  arm         sa1100         -           -               -                   jornada                              -                                                                                                                                 Kristoffer Ericson <[email protected]>
+Active  arm         armv8          -           armltd          vexpress64          vexpress_aemv8a                      vexpress_aemv8a:ARM64                                                                                                             David Feng <[email protected]>
 Active  avr32       at32ap         at32ap700x  atmel           -                   atngw100                             -                                                                                                                                 Haavard Skinnemoen <[email protected]>
 Active  avr32       at32ap         at32ap700x  atmel           -                   atngw100mkii                         -                                                                                                                                 Andreas Bie?mann <[email protected]>
 Active  avr32       at32ap         at32ap700x  atmel           atstk1000           atstk1002                            -                                                                                                                                 Haavard Skinnemoen <[email protected]>
include/configs/vexpress_aemv8a.h new file +191 -0

191 lines not on this page · raw message

Signature · 1 line
1.7.9.5
#3 lore raw

PATCH v13 3/6 generic board patch of manual reloc and zero gd_t

From: David Feng <[email protected]>

---
 common/board_f.c |   18 +++++++++++-------
 common/board_r.c |   20 +++++++++++++++++++-
 2 files changed, 30 insertions(+), 8 deletions(-)
common/board_f.c +11 -7
index 0ada1af..5891ad2 100644
@@ -458,7 +458,7 @@ static int reserve_round_4k(void)
 static int reserve_mmu(void)
 {
 	/* reserve TLB table */
-	gd->arch.tlb_size = 4096 * 4;
+	gd->arch.tlb_size = PGTABLE_SIZE;
 	gd->relocaddr -= gd->arch.tlb_size;
 
 	/* round down to next 64 kB limit */
@@ -610,7 +610,7 @@ static int reserve_stacks(void)
 	 * TODO(sjg at chromium.org): Perhaps create arch_reserve_stack()
 	 * to handle this and put in arch/xxx/lib/stack.c
 	 */
-# ifdef CONFIG_ARM
+# if defined(CONFIG_ARM) && !defined(CONFIG_ARM64)
 #  ifdef CONFIG_USE_IRQ
 	gd->start_addr_sp -= (CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ);
 	debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
@@ -807,11 +807,6 @@ static int mark_bootstage(void)
 }
 
 static init_fnc_t init_sequence_f[] = {
-#if !defined(CONFIG_CPM2) && !defined(CONFIG_MPC512X) && \
-		!defined(CONFIG_MPC83xx) && !defined(CONFIG_MPC85xx) && \
-		!defined(CONFIG_MPC86xx) && !defined(CONFIG_X86)
-	zero_global_data,
-#endif
 #ifdef CONFIG_SANDBOX
 	setup_ram_buf,
 #endif
@@ -1005,6 +1000,15 @@ void board_init_f(ulong boot_flags)
 	gd = &data;
 #endif
 
+	/*
+	 * Zero gd_t first, otherwise the debug print(if DEBUG defined)
+	 * in initcall_run_list function before zero_global_data is called
+	 * will go wrong.
+	 */
+#ifndef CONFIG_X86
+	zero_global_data();
+#endif
+
 	gd->flags = boot_flags;
 
 	if (initcall_run_list(init_sequence_f))
common/board_r.c +19 -1
index 86ca1cb..8984cf3 100644
@@ -157,6 +157,13 @@ static int initr_reloc_global_data(void)
 	 */
 	gd->env_addr += gd->relocaddr - CONFIG_SYS_MONITOR_BASE;
 #endif
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+	/*
+	 * We have to relocate the command table manually
+	 */
+	fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd),
+			ll_entry_count(cmd_tbl_t, cmd));
+#endif /* CONFIG_NEEDS_MANUAL_RELOC */
 	return 0;
 }
 
@@ -705,6 +712,7 @@ static int run_main_loop(void)
  * TODO: perhaps reset the watchdog in the initcall function after each call?
  */
 init_fnc_t init_sequence_r[] = {
+	initr_serial,
 	initr_trace,
 	initr_reloc,
 	/* TODO: could x86/PPC have this also perhaps? */
@@ -722,7 +730,6 @@ init_fnc_t init_sequence_r[] = {
 	set_cpu_clk_info, /* Setup clock information */
 #endif
 	initr_reloc_global_data,
-	initr_serial,
 	initr_announce,
 	INIT_FUNC_WATCHDOG_RESET
 #ifdef CONFIG_PPC
@@ -899,6 +906,7 @@ init_fnc_t init_sequence_r[] = {
 	initr_modem,
 #endif
 	run_main_loop,
+	NULL,
 };
 
 void board_init_r(gd_t *new_gd, ulong dest_addr)
@@ -906,6 +914,16 @@ void board_init_r(gd_t *new_gd, ulong dest_addr)
 #ifndef CONFIG_X86
 	gd = new_gd;
 #endif
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+	/*
+	 * We have to relocate the init_sequence_r table manually
+	 */
+	init_fnc_t	*init_fnc_ptr;
+	for (init_fnc_ptr = init_sequence_r; *init_fnc_ptr; ++init_fnc_ptr)
+		*(unsigned long *)init_fnc_ptr =
+			(unsigned long)(*init_fnc_ptr) + gd->reloc_off;
+#endif /* CONFIG_NEEDS_MANUAL_RELOC */
+
 	if (initcall_run_list(init_sequence_r))
 		hang();
 
Signature · 1 line
1.7.9.5
#4 lore raw

PATCH v13 4/6 64bit initrd start address support

From: David Feng <[email protected]>

---
 common/fdt_support.c |   66 ++++++++++++++++++++++++++------------------------
 1 file changed, 34 insertions(+), 32 deletions(-)
common/fdt_support.c +34 -32
index b034c98..9bc5821 100644
@@ -21,6 +21,34 @@
  */
 DECLARE_GLOBAL_DATA_PTR;
 
+/*
+ * Get cells len in bytes
+ *     if #NNNN-cells property is 2 then len is 8
+ *     otherwise len is 4
+ */
+static int get_cells_len(void *blob, char *nr_cells_name)
+{
+	const fdt32_t *cell;
+
+	cell = fdt_getprop(blob, 0, nr_cells_name, NULL);
+	if (cell && fdt32_to_cpu(*cell) == 2)
+		return 8;
+
+	return 4;
+}
+
+/*
+ * Write a 4 or 8 byte big endian cell
+ */
+static void write_cell(u8 *addr, u64 val, int size)
+{
+	int shift = (size - 1) * 8;
+	while (size-- > 0) {
+		*addr++ = (val >> shift) & 0xff;
+		shift -= 8;
+	}
+}
+
 /**
  * fdt_getprop_u32_default - Find a node and return it's property or a default
  *
@@ -131,9 +159,9 @@ static int fdt_fixup_stdout(void *fdt, int chosenoff)
 
 int fdt_initrd(void *fdt, ulong initrd_start, ulong initrd_end, int force)
 {
-	int   nodeoffset;
+	int   nodeoffset, addr_cell_len;
 	int   err, j, total;
-	fdt32_t  tmp;
+	fdt64_t  tmp;
 	const char *path;
 	uint64_t addr, size;
 
@@ -170,9 +198,11 @@ int fdt_initrd(void *fdt, ulong initrd_start, ulong initrd_end, int force)
 		return err;
 	}
 
+	addr_cell_len = get_cells_len(fdt, "#address-cells");
+
 	path = fdt_getprop(fdt, nodeoffset, "linux,initrd-start", NULL);
 	if ((path == NULL) || force) {
-		tmp = cpu_to_fdt32(initrd_start);
+		write_cell((u8 *)&tmp, initrd_start, addr_cell_len);
 		err = fdt_setprop(fdt, nodeoffset,
 			"linux,initrd-start", &tmp, sizeof(tmp));
 		if (err < 0) {
@@ -181,7 +211,7 @@ int fdt_initrd(void *fdt, ulong initrd_start, ulong initrd_end, int force)
 				fdt_strerror(err));
 			return err;
 		}
-		tmp = cpu_to_fdt32(initrd_end);
+		write_cell((u8 *)&tmp, initrd_end, addr_cell_len);
 		err = fdt_setprop(fdt, nodeoffset,
 			"linux,initrd-end", &tmp, sizeof(tmp));
 		if (err < 0) {
@@ -343,34 +373,6 @@ void do_fixup_by_compat_u32(void *fdt, const char *compat,
 	do_fixup_by_compat(fdt, compat, prop, &tmp, 4, create);
 }
 
-/*
- * Get cells len in bytes
- *     if #NNNN-cells property is 2 then len is 8
- *     otherwise len is 4
- */
-static int get_cells_len(void *blob, char *nr_cells_name)
-{
-	const fdt32_t *cell;
-
-	cell = fdt_getprop(blob, 0, nr_cells_name, NULL);
-	if (cell && fdt32_to_cpu(*cell) == 2)
-		return 8;
-
-	return 4;
-}
-
-/*
- * Write a 4 or 8 byte big endian cell
- */
-static void write_cell(u8 *addr, u64 val, int size)
-{
-	int shift = (size - 1) * 8;
-	while (size-- > 0) {
-		*addr++ = (val >> shift) & 0xff;
-		shift -= 8;
-	}
-}
-
 #ifdef CONFIG_NR_DRAM_BANKS
 #define MEMORY_BANKS_MAX CONFIG_NR_DRAM_BANKS
 #else
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH v13 5/6 remove compiling warnings

From: David Feng <[email protected]>

---
 common/cmd_pxe.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
common/cmd_pxe.c +2 -2
index a2fb50a..df58522 100644
@@ -57,7 +57,7 @@ static int format_mac_pxe(char *outbuf, size_t outbuf_len)
 	uchar ethaddr[6];
 
 	if (outbuf_len < 21) {
-		printf("outbuf is too small (%d < 21)\n", outbuf_len);
+		printf("outbuf is too small (%zd < 21)\n", outbuf_len);
 
 		return -EINVAL;
 	}
@@ -100,7 +100,7 @@ static int get_bootfile_path(const char *file_path, char *bootfile_path,
 	path_len = (last_slash - bootfile) + 1;
 
 	if (bootfile_path_size < path_len) {
-		printf("bootfile_path too small. (%d < %d)\n",
+		printf("bootfile_path too small. (%zd < %zd)\n",
 				bootfile_path_size, path_len);
 
 		return -1;
Signature · 1 line
1.7.9.5
#6 lore raw

PATCH v13 6/6 add weak entry definition

From: David Feng <[email protected]>

---
 include/linux/linkage.h |    4 ++++
 1 file changed, 4 insertions(+)
include/linux/linkage.h +4 -0
index 9ddf830..2a2848a 100644
@@ -49,6 +49,10 @@
 	.globl SYMBOL_NAME(name); \
 	LENTRY(name)
 
+#define WEAK(name) \
+	.weak SYMBOL_NAME(name); \
+	LENTRY(name)
+
 #ifndef END
 #define END(name) \
 	.size name, .-name
Signature · 1 line
1.7.9.5
#7 lore raw

PATCH v13 6/6 add weak entry definition

Quoted 6 lines · fenghua at phytium.com.cn

From: David Feng <[email protected]>

---
 include/linux/linkage.h |    4 ++++
 1 file changed, 4 insertions(+)

This patch should come before adding core v8 support.

Rob

Quoted 17 lines
include/linux/linkage.h +4 -0
index 9ddf830..2a2848a 100644
@@ -49,6 +49,10 @@
 	.globl SYMBOL_NAME(name); \
 	LENTRY(name)
 
+#define WEAK(name) \
+	.weak SYMBOL_NAME(name); \
+	LENTRY(name)
+
 #ifndef END
 #define END(name) \
 	.size name, .-name
#8 lore raw

PATCH v13 1/6 core support of arm64

In reply to fenghua at phytium.com.cn
Quoted 5 lines · fenghua at phytium.com.cn

From: David Feng <[email protected]>

---
 arch/arm/config.mk                      |    4 +

FYI, some recent mainline changes to config.mk break the build for me.

Quoted 792 lines
 arch/arm/cpu/armv8/Makefile             |   38 +++++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 ++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 +++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++++++
 arch/arm/cpu/armv8/exceptions.S         |  115 +++++++++++++++
 arch/arm/cpu/armv8/start.S              |  234 +++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 +++++++++++
 arch/arm/cpu/armv8/tlb.S                |   30 ++++
 arch/arm/cpu/armv8/u-boot.lds           |   71 ++++++++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 ++
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 +++++++++++++++
 arch/arm/include/asm/byteorder.h        |   12 ++
 arch/arm/include/asm/cache.h            |    5 +
 arch/arm/include/asm/config.h           |   10 ++
 arch/arm/include/asm/global_data.h      |    6 +-
 arch/arm/include/asm/io.h               |   15 +-
 arch/arm/include/asm/macro.h            |   39 ++++++
 arch/arm/include/asm/posix_types.h      |   10 ++
 arch/arm/include/asm/proc-armv/ptrace.h |   21 +++
 arch/arm/include/asm/proc-armv/system.h |   59 +++++++-
 arch/arm/include/asm/system.h           |   77 ++++++++++
 arch/arm/include/asm/types.h            |    4 +
 arch/arm/include/asm/u-boot.h           |    4 +
 arch/arm/include/asm/unaligned.h        |    2 +-
 arch/arm/lib/Makefile                   |   14 ++
 arch/arm/lib/board.c                    |   25 +++-
 arch/arm/lib/bootm.c                    |   16 +++
 arch/arm/lib/crt0_64.S                  |  116 +++++++++++++++
 arch/arm/lib/interrupts_64.c            |  120 ++++++++++++++++
 arch/arm/lib/relocate_64.S              |   57 ++++++++
 common/image.c                          |    1 +
 doc/README.arm64                        |   33 +++++
 examples/standalone/stubs.c             |   15 ++
 include/image.h                         |    1 +
 36 files changed, 1775 insertions(+), 11 deletions(-)
 create mode 100644 arch/arm/cpu/armv8/Makefile
 create mode 100644 arch/arm/cpu/armv8/cache.S
 create mode 100644 arch/arm/cpu/armv8/cache_v8.c
 create mode 100644 arch/arm/cpu/armv8/config.mk
 create mode 100644 arch/arm/cpu/armv8/cpu.c
 create mode 100644 arch/arm/cpu/armv8/exceptions.S
 create mode 100644 arch/arm/cpu/armv8/start.S
 create mode 100644 arch/arm/cpu/armv8/timer.c
 create mode 100644 arch/arm/cpu/armv8/tlb.S
 create mode 100644 arch/arm/cpu/armv8/u-boot.lds
 create mode 100644 arch/arm/include/asm/arch-armv8/gpio.h
 create mode 100644 arch/arm/include/asm/arch-armv8/mmu.h
 create mode 100644 arch/arm/lib/crt0_64.S
 create mode 100644 arch/arm/lib/interrupts_64.c
 create mode 100644 arch/arm/lib/relocate_64.S
 create mode 100644 doc/README.arm64
arch/arm/config.mk +4 -0
index ce3903b..95c07ad 100644
@@ -74,7 +74,9 @@ endif
 endif
 
 # needed for relocation
+ifndef CONFIG_ARM64
 LDFLAGS_u-boot += -pie
+endif
 
 #
 # FIXME: binutils versions < 2.22 have a bug in the assembler where
@@ -95,6 +97,8 @@ endif
 endif
 
 # check that only R_ARM_RELATIVE relocations are generated
+ifndef CONFIG_ARM64
 ifneq ($(CONFIG_SPL_BUILD),y)
 ALL-y	+= checkarmreloc
 endif
+endif
arch/arm/cpu/armv8/Makefile new file +38 -0
new file mode 100644
index 0000000..b216f27
@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(CPU).o
+
+START	:= start.o
+
+COBJS	+= cpu.o
+COBJS	+= timer.o
+COBJS	+= cache_v8.o
+
+SOBJS	+= exceptions.o
+SOBJS	+= cache.o
+SOBJS	+= tlb.o
+
+SRCS	:= $(START:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+START	:= $(addprefix $(obj),$(START))
+
+all:	$(obj).depend $(START) $(LIB)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
arch/arm/cpu/armv8/cache.S new file +130 -0
new file mode 100644
index 0000000..419f169
@@ -0,0 +1,130 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <version.h>
+#include <asm/macro.h>
+#include <linux/linkage.h>
+
+/*
+ * void __asm_flush_dcache_level(level)
+ *
+ * clean and invalidate one level cache.
+ *
+ * x0: cache level
+ * x1~x9: clobbered
+ */
+ENTRY(__asm_flush_dcache_level)
+	lsl	x1, x0, #1
+	msr	csselr_el1, x1		/* select cache level */
+	isb				/* isb to sych the new cssr & csidr */
+	mrs	x6, ccsidr_el1		/* read the new ccsidr */
+	and	x2, x6, #7		/* x2 <- length of the cache lines */
+	add	x2, x2, #4		/* add 4 (line length offset) */
+	mov	x3, #0x3ff
+	and	x3, x3, x6, lsr #3	/* x3 <- maximum number of way size */
+	clz	w5, w3			/* bit position of way size */
+	mov	x4, #0x7fff
+	and	x4, x4, x1, lsr #13	/* x4 <- max number of the set size */
+	/* x1 <- cache level << 1 */
+	/* x2 <- line length offset */
+	/* x3 <- number of cache ways */
+	/* x4 <- number of cache sets */
+	/* x5 <- bit position of way size */
+
+loop_set:
+	mov	x6, x3			/* create working copy of way size */
+loop_way:
+	lsl	x7, x6, x5
+	orr	x9, x0, x7		/* map way and level to cisw value */
+	lsl	x7, x4, x2
+	orr	x9, x9, x7		/* map set number to cisw value */
+	dc	cisw, x9		/* clean & invalidate by set/way */
+	subs	x6, x6, #1		/* decrement the way */
+	b.ge	loop_way
+	subs	x4, x4, #1		/* decrement the set */
+	b.ge	loop_set
+
+	ret
+ENDPROC(__asm_flush_dcache_level)
+
+/*
+ * void __asm_flush_dcache_all(void)
+ *
+ * clean and invalidate all data cache by SET/WAY.
+ */
+ENTRY(__asm_flush_dcache_all)
+	dsb	sy
+	mov	x15, lr
+	mrs	x10, clidr_el1		/* read clidr */
+	lsr	x11, x10, #24
+	and	x11, x11, #0x7		/* x11 <- loc */
+	cbz	x11, finished		/* if loc is 0, no need to clean */
+	mov	x0, #0			/* start flush at cache level 0 */
+	/* x0  <- cache level */
+	/* x10 <- clidr_el1 */
+	/* x11 <- loc */
+
+loop_level:
+	lsl	x1, x0, #1
+	add	x1, x1, x0		/* x0 <- 3x cache level */
+	lsr	x1, x10, x1
+	and	x1, x1, #7		/* x1 <- cache type */
+	cmp	x1, #2
+	b.lt	skip			/* skip if no cache or icache */
+	bl	__asm_flush_dcache_level
+skip:
+	add	x0, x0, #1		/* increment cache level */
+	cmp	x11, x0
+	b.gt	loop_level
+
+finished:
+	mov	x0, #0
+	msr	csselr_el1, x0		/* swith back to cache level 0 */
+	dsb	sy
+	isb
+	mov	lr, x15
+	ret
+ENDPROC(__asm_flush_dcache_all)
+
+/*
+ * void __asm_flush_dcache_range(start, end)
+ *
+ * clean & invalidate data cache in the range
+ *
+ * x0: start address
+ * x1: end address
+ */
+ENTRY(__asm_flush_dcache_range)
+	mrs	x3, ctr_el0		/* read CTR */
+	lsr	x3, x3, #16
+	and	x3, x3, #0xf		/* cache line size encoding */
+	mov	x2, #4			/* bytes per word */
+	lsl	x2, x2, x3		/* actual cache line size */
+
+	/* x2 <- minimal cache line size in cache system */
+	sub	x3, x2, #1
+	bic	x0, x0, x3
+1:      dc	civac, x0		/* clean & invalidate D/unified line */
+	add	x0, x0, x2
+	cmp	x0, x1
+	b.lo	1b
+	dsb	sy
+	ret
+ENDPROC(__asm_flush_dcache_range)
+
+/*
+ * void __asm_invalidate_icache_all(void)
+ *
+ * invalidate all tlb entries.
+ */
+ENTRY(__asm_invalidate_icache_all)
+	ic	ialluis
+	isb	sy
+	ret
+ENDPROC(__asm_invalidate_icache_all)
arch/arm/cpu/armv8/cache_v8.c new file +218 -0
new file mode 100644
index 0000000..34426fd
@@ -0,0 +1,218 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/system.h>
+#include <asm/arch/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+
+static void set_pgtable_section(u64 section, u64 memory_type)
+{
+	u64 *page_table = (u64 *)gd->arch.tlb_addr;
+	u64 value;
+
+	value = (section << SECTION_SHIFT) | PMD_TYPE_SECT | PMD_SECT_AF;
+	value |= PMD_ATTRINDX(memory_type);
+	page_table[section] = value;
+}
+
+/* to activate the MMU we need to set up virtual memory */
+static void mmu_setup(void)
+{
+	int i, j, el;
+	bd_t *bd = gd->bd;
+
+	/* Setup an identity-mapping for all spaces */
+	for (i = 0; i < (PAGE_SIZE >> 3); i++)
+		set_pgtable_section(i, MT_DEVICE_NGNRNE);
+
+	/* Setup an identity-mapping for all RAM space */
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		ulong start = bd->bi_dram[i].start;
+		ulong end = bd->bi_dram[i].start + bd->bi_dram[i].size;
+		for (j = start >> SECTION_SHIFT;
+		     j < end >> SECTION_SHIFT; j++) {
+			set_pgtable_section(j, MT_NORMAL);
+		}
+	}
+
+	/* load TTBR0 */
+	el = curent_el();
+	if (el == 1)
+		asm volatile("msr ttbr0_el1, %0"
+			     : : "r" (gd->arch.tlb_addr) : "memory");
+	else if (el == 2)
+		asm volatile("msr ttbr0_el2, %0"
+			     : : "r" (gd->arch.tlb_addr) : "memory");
+	else
+		panic("Not Supported Exception Level");
+
+	/* enable the mmu */
+	set_sctlr(get_sctlr() | CR_M);
+}
+
+/*
+ * Performs a invalidation of the entire data cache at all levels
+ */
+void invalidate_dcache_all(void)
+{
+	__asm_flush_dcache_all();
+}
+
+/*
+ * Performs a clean & invalidation of the entire data cache at all levels
+ */
+void flush_dcache_all(void)
+{
+	__asm_flush_dcache_all();
+}
+
+/*
+ * Invalidates range in all levels of D-cache/unified cache
+ */
+void invalidate_dcache_range(unsigned long start, unsigned long stop)
+{
+	__asm_flush_dcache_range(start, stop);
+}
+
+/*
+ * Flush range(clean & invalidate) from all levels of D-cache/unified cache
+ */
+void flush_dcache_range(unsigned long start, unsigned long stop)
+{
+	__asm_flush_dcache_range(start, stop);
+}
+
+void dcache_enable(void)
+{
+	/* The data cache is not active unless the mmu is enabled */
+	if (!(get_sctlr() & CR_M)) {
+		invalidate_dcache_all();
+		__asm_invalidate_tlb_all();
+		mmu_setup();
+	}
+
+	set_sctlr(get_sctlr() | CR_C);
+}
+
+void dcache_disable(void)
+{
+	uint32_t sctlr;
+
+	sctlr = get_sctlr();
+
+	/* if cache isn't enabled no need to disable */
+	if (!(sctlr & CR_C))
+		return;
+
+	set_sctlr(sctlr & ~(CR_C|CR_M));
+
+	flush_dcache_all();
+	__asm_invalidate_tlb_all();
+}
+
+int dcache_status(void)
+{
+	return (get_sctlr() & CR_C) != 0;
+}
+
+#else	/* CONFIG_SYS_DCACHE_OFF */
+
+void invalidate_dcache_all(void)
+{
+}
+
+void flush_dcache_all(void)
+{
+}
+
+void invalidate_dcache_range(unsigned long start, unsigned long stop)
+{
+}
+
+void flush_dcache_range(unsigned long start, unsigned long stop)
+{
+}
+
+void dcache_enable(void)
+{
+}
+
+void dcache_disable(void)
+{
+}
+
+int dcache_status(void)
+{
+	return 0;
+}
+
+#endif	/* CONFIG_SYS_DCACHE_OFF */
+
+#ifndef CONFIG_SYS_ICACHE_OFF
+
+void icache_enable(void)
+{
+	set_sctlr(get_sctlr() | CR_I);
+}
+
+void icache_disable(void)
+{
+	set_sctlr(get_sctlr() & ~CR_I);
+}
+
+int icache_status(void)
+{
+	return (get_sctlr() & CR_I) != 0;
+}
+
+void invalidate_icache_all(void)
+{
+	__asm_invalidate_icache_all();
+}
+
+#else	/* CONFIG_SYS_ICACHE_OFF */
+
+void icache_enable(void)
+{
+}
+
+void icache_disable(void)
+{
+}
+
+int icache_status(void)
+{
+	return 0;
+}
+
+void invalidate_icache_all(void)
+{
+}
+
+#endif	/* CONFIG_SYS_ICACHE_OFF */
+
+/*
+ * Enable dCache & iCache, whether cache is actually enabled
+ * depend on CONFIG_SYS_DCACHE_OFF and CONFIG_SYS_ICACHE_OFF
+ */
+void enable_caches(void)
+{
+	icache_enable();
+	dcache_enable();
+}
+
+/*
+ * Flush range from all levels of d-cache/unified-cache
+ */
+void flush_cache(unsigned long start, unsigned long size)
+{
+	flush_dcache_range(start, start + size);
+}
arch/arm/cpu/armv8/config.mk new file +16 -0
new file mode 100644
index 0000000..9f36d59
@@ -0,0 +1,16 @@
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+PLATFORM_RELFLAGS += -fno-common -ffixed-x18
+
+# SEE README.arm-unaligned-accesses
+PF_NO_UNALIGNED := $(call cc-option, -mstrict-align)
+PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
+
+PF_CPPFLAGS_ARMV8 := $(call cc-option, -march=armv8-a)
+PLATFORM_CPPFLAGS += $(PF_CPPFLAGS_ARMV8)
+PLATFORM_CPPFLAGS += $(PF_NO_UNALIGNED)
+PLATFORM_CPPFLAGS += -fpic
arch/arm/cpu/armv8/cpu.c new file +67 -0
new file mode 100644
index 0000000..83e73ab
@@ -0,0 +1,67 @@
+/*
+ * (C) Copyright 2008 Texas Insturments
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <[email protected]>
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * CPU specific code
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/system.h>
+#include <linux/compiler.h>
+
+void __weak cpu_cache_initialization(void){}
+
+int cleanup_before_linux(void)
+{
+	/*
+	 * this function is called just before we call linux
+	 * it prepares the processor for linux
+	 *
+	 * we turn off caches etc ...
+	 */
+#ifndef CONFIG_SPL_BUILD
+	disable_interrupts();
+#endif
+
+	/*
+	 * Turn off I-cache and invalidate it
+	 */
+	icache_disable();
+	invalidate_icache_all();
+
+	/*
+	 * turn off D-cache
+	 * dcache_disable() in turn flushes the d-cache and disables MMU
+	 */
+	dcache_disable();
+
+	/*
+	 * After D-cache is flushed and before it is disabled there may
+	 * be some new valid entries brought into the cache. We are sure
+	 * that these lines are not dirty and will not affect our execution.
+	 * (because unwinding the call-stack and setting a bit in CP15 SCTRL
+	 * is all we did during this. We have not pushed anything on to the
+	 * stack. Neither have we affected any static data)
+	 * So just invalidate the entire d-cache again to avoid coherency
+	 * problems for kernel
+	 */
+	invalidate_dcache_all();
+
+	/*
+	 * Some CPU need more cache attention before starting the kernel.
+	 */
+	cpu_cache_initialization();
+
+	return 0;
+}
arch/arm/cpu/armv8/exceptions.S new file +115 -0
new file mode 100644
index 0000000..b2f62c9
@@ -0,0 +1,115 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <version.h>
+#include <asm/ptrace.h>
+#include <asm/macro.h>
+#include <linux/linkage.h>
+
+/*
+ * Enter Exception.
+ * This will save the processor state that is ELR/X0~X30
+ * to the stack frame.
+ */
+.macro	exception_entry
+	stp	x29, x30, [sp, #-16]!
+	stp	x27, x28, [sp, #-16]!
+	stp	x25, x26, [sp, #-16]!
+	stp	x23, x24, [sp, #-16]!
+	stp	x21, x22, [sp, #-16]!
+	stp	x19, x20, [sp, #-16]!
+	stp	x17, x18, [sp, #-16]!
+	stp	x15, x16, [sp, #-16]!
+	stp	x13, x14, [sp, #-16]!
+	stp	x11, x12, [sp, #-16]!
+	stp	x9, x10, [sp, #-16]!
+	stp	x7, x8, [sp, #-16]!
+	stp	x5, x6, [sp, #-16]!
+	stp	x3, x4, [sp, #-16]!
+	stp	x1, x2, [sp, #-16]!
+
+	/* Could be running at EL1 or EL2 */
+	mrs	x11, CurrentEL
+	cmp	x11, 0x4
+	b.eq	1f
+	cmp	x11, 0x8
+	b.eq	2f
+	b	3f
+1:	mrs	x1, esr_el1
+	mrs	x2, elr_el1
+	b	3f
+2:	mrs	x1, esr_el2
+	mrs	x2, elr_el2
+3:
+	stp	x2, x0, [sp, #-16]!
+	mov	x0, sp
+.endm
+
+/*
+ * Exception vectors.
+ */
+	.align	11
+	.globl	vectors
+vectors:
+	.align	7
+	b	_do_bad_sync	/* Current EL Synchronous Thread */
+
+	.align	7
+	b	_do_bad_irq	/* Current EL IRQ Thread */
+
+	.align	7
+	b	_do_bad_fiq	/* Current EL FIQ Thread */
+
+	.align	7
+	b	_do_bad_error	/* Current EL Error Thread */
+
+	.align	7
+	b	_do_sync	/* Current EL Synchronous Handler */
+
+	.align	7
+	b	_do_irq		/* Current EL IRQ Handler */
+
+	.align	7
+	b	_do_fiq		/* Current EL FIQ Handler */
+
+	.align	7
+	b	_do_error	/* Current EL Error Handler */
+
+
+_do_bad_sync:
+	exception_entry
+	bl	do_bad_sync
+
+_do_bad_irq:
+	exception_entry
+	bl	do_bad_irq
+
+_do_bad_fiq:
+	exception_entry
+	bl	do_bad_fiq
+
+_do_bad_error:
+	exception_entry
+	bl	do_bad_error
+
+_do_sync:
+	exception_entry
+	bl	do_sync
+
+_do_irq:
+	exception_entry
+	bl	do_irq
+
+_do_fiq:
+	exception_entry
+	bl	do_fiq
+
+_do_error:
+	exception_entry
+	bl	do_error
arch/arm/cpu/armv8/start.S new file +90 -0
new file mode 100644
index 0000000..28c8fe3
@@ -0,0 +1,234 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <version.h>
+#include <linux/linkage.h>
+#include <asm/macro.h>
+#include <asm/arch/mmu.h>
+
+/*************************************************************************
+ *
+ * Startup Code (reset vector)
+ *
+ *************************************************************************/
+
+.globl	_start
+_start:
+	b	reset
+
+	.align 3
+
+.globl	_TEXT_BASE
+_TEXT_BASE:
+	.quad	CONFIG_SYS_TEXT_BASE
+
+/*
+ * These are defined in the linker script.
+ */
+.globl	_end_ofs
+_end_ofs:
+	.quad	_end - _start
+
+.globl	_bss_start_ofs
+_bss_start_ofs:
+	.quad	__bss_start - _start
+
+.globl	_bss_end_ofs
+_bss_end_ofs:
+	.quad	__bss_end - _start
+
+reset:
+	/*
+	 * Could be EL3/EL2/EL1
+	 */
+	mrs	x0, CurrentEL
+	cmp	x0, #0xc
+	b.ne	reset_nonsecure			/* Not EL3 */
+
+	bl	setup_el3			/* EL3 initialization */
+
+	/*
+	 * MMU Disabled, iCache Disabled, dCache Disabled
+	 */
+reset_nonsecure:
+
+#ifdef CONFIG_BOOTING_EL1
+	switch_el1_el2 x0, 1f, 2f, 3f
+1:	b	3f
+2:	bl	setup_el2			/* EL2 initialization */
+3:
+#endif
+
+	/* Initialize vBAR/CPACR_EL1/MDSCR_EL1 */
+	adr	x0, vectors
+	switch_el1_el2 x1, 1f, 2f, 3f
+1:	msr	vbar_el1, x0
+	mov	x0, #3 << 20
+	msr	cpacr_el1, x0			/* Enable FP/SIMD */
+	msr	mdscr_el1, xzr
+	b	3f
+2:	msr	vbar_el2, x0
+3:
+
+	/* Cache/BPB/TLB Invalidate */
+	bl	__asm_flush_dcache_all		/* dCache clean & invalidate */
+	bl	__asm_invalidate_icache_all	/* iCache invalidate */
+	bl	__asm_invalidate_tlb_all	/* invalidate TLBs */
+
+	/* Processor specific initialization */
+	bl	lowlevel_init
+
+	branch_if_slave	x0, slave_cpu
+
+	/*
+	 * Master CPU

arch/arm/cpu/armv8/start.S line 100

Quoted 10 lines
arch/arm/cpu/armv8/start.S new file +10 -0
+	 */
+master_cpu:
+	bl	_main
+
+	/*
+	 * Slave CPUs
+	 */
+slave_cpu:
+	wfe
+	ldr	x1, =SECONDARY_CPU_MAILBOX

This is platform specific. Not all platforms will boot secondary cores into u-boot.

You could simply ifdef this code with SECONDARY_CPU_MAILBOX.

arch/arm/cpu/armv8/start.S line 107

Quoted 7 lines
arch/arm/cpu/armv8/start.S new file +7 -0
+	ldr	x0, [x1]
+	cbz	x0, slave_cpu
+	br	x0			/* branch to the given address */
+
+/*-------------------------------------------------------------------------*/
+
+WEAK(setup_el3)

This function should be optional so platforms don't have to define GIC_DIST_BASE, GIC_CPU_BASE, and CONFIG_SYS_CNTFRQ.

Quoted 167 lines
arch/arm/cpu/armv8/start.S new file +127 -0
+	mov	x0, #0x531	/* Non-secure EL0/EL1 | HVC | 64bit EL2 */
+	msr	scr_el3, x0
+	msr	cptr_el3, xzr	/* Disable coprocessor traps to EL3 */
+
+	/* GIC initialization */
+	branch_if_slave	x0, 2f
+
+	/* Master initialize distributor */
+	ldr	x1, =GIC_DIST_BASE	/* GICD_CTLR */
+	mov	w0, #0x3		/* Enable Group0 & Group1 */
+	str	w0, [x1]
+	ldr	w0, [x1, #0x4]		/* GICD_TYPER */
+	and	w2, w0, #0x1f		/* ITLinesNumber */
+	add	w2, w2, #0x1		/* Number of GICD_IGROUPR registers */
+	add	x1, x1, #0x80		/* GICD_IGROUPR */
+	mov	w0, #~0			/* All Group1 */
+1:	str	w0, [x1], #0x4
+	sub	w2, w2, #0x1
+	cbnz	w2, 1b
+	b	3f
+
+	/* Slave initialize distributor */
+2:	ldr	x1, =GIC_DIST_BASE	/* GICD_CTLR */
+	mov	w0, #~0			/* All Group1 */
+	str	w0, [x1, #0x80]
+
+	/* Initialize cpu interface */
+3:	ldr	x1, =GIC_CPU_BASE	/* GICC_CTLR */
+	mov	w0, #0x3		/* Enable Group0 & Group1 */
+	str	w0, [x1]
+
+	mov	w0, #0x1 << 7		/* Non-Secure access to GICC_PMR */
+	str	w0, [x1, #0x4]		/* GICC_PMR */
+
+	/* Counter frequency initialization */
+	ldr	x0, =CONFIG_SYS_CNTFRQ
+	msr	cntfrq_el0, x0
+
+	/* SCTLR_EL2 initialization */
+	msr	sctlr_el2, xzr
+
+	/* Return to the EL2_SP2 mode from EL3 */
+	mov	x0, #0x3c9		/* EL2_SP2 | D | A | I | F */
+	msr	elr_el3, lr
+	msr	spsr_el3, x0
+	eret
+ENDPROC(setup_el3)
+
+WEAK(setup_el2)
+	/* Initialize Generic Timers */
+	mrs	x0, cnthctl_el2
+	orr	x0, x0, #0x3		/* Enable EL1 access to timers */
+	msr	cnthctl_el2, x0
+	msr	cntvoff_el2, x0		/* Clear virtual offset */
+	mrs	x0, cntkctl_el1
+	orr	x0, x0, #0x3		/* EL0 access to counters */
+	msr	cntkctl_el1, x0
+
+	/* Initilize MPID/MPIDR registers */
+	mrs	x0, midr_el1
+	mrs	x1, mpidr_el1
+	msr	vpidr_el2, x0
+	msr	vmpidr_el2, x1
+
+	/* Disable coprocessor traps */
+	mov	x0, #0x33ff
+	msr	cptr_el2, x0		/* Disable coprocessor traps to EL2 */
+	msr	hstr_el2, xzr		/* Disable CP15 traps to EL2 */
+
+	/* Initialize HCR_EL2 */
+	mov	x0, #(1 << 31)		/* 64bit EL1 */
+	orr	x0, x0, #(1 << 29)	/* Disable HVC */
+	msr	hcr_el2, x0
+
+	/* SCTLR_EL1 initialization */
+	mov	x0, #0x0800
+	movk	x0, #0x30d0, lsl #16
+	msr	sctlr_el1, x0
+
+	/* Return to the EL1_SP1 mode from EL2 */
+	mov	x0, #0x3c5		/* EL1_SP1 | D | A | I | F */
+	msr	elr_el2, lr
+	msr	spsr_el2, x0
+	eret
+ENDPROC(setup_el2)
+
+WEAK(lowlevel_init)
+	ret
+ENDPROC(lowlevel_init)
+
+/*-------------------------------------------------------------------------*/
+
+ENTRY(c_runtime_cpu_setup)
+	/* If I-cache is enabled invalidate it */
+#ifndef CONFIG_SYS_ICACHE_OFF
+	ic	iallu			/* I+BTB cache invalidate */
+	isb	sy
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+	/*
+	 * Setup MAIR and TCR. Using 512GB address range.
+	 */
+	ldr	x0, =MEMORY_ATTRIBUTES
+	ldr	x1, =TCR_FLAGS
+
+	switch_el1_el2 x2, 1f, 2f, 3f
+1:	orr	x1, x1, TCR_EL1_IPS_40BIT
+	msr	mair_el1, x0
+	msr	tcr_el1, x1
+	b	3f
+2:	orr	x1, x1, TCR_EL2_IPS_40BIT
+	msr	mair_el2, x0
+	msr	tcr_el2, x1
+3:
+#endif
+
+	/* Relocate vBAR */
+	adr	x0, vectors
+	switch_el1_el2 x1, 1f, 2f, 3f
+1:	msr	vbar_el1, x0
+	b	3f
+2:	msr	vbar_el2, x0
+3:
+
+	ret
+ENDPROC(c_runtime_cpu_setup)
arch/arm/cpu/armv8/timer.c new file +34 -0
new file mode 100644
index 0000000..9605e84
@@ -0,0 +1,80 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <div64.h>
+#include <linux/compiler.h>
+
+/*
+ * Genertic Timer implementation of __udelay/get_timer/get_ticks/get_tbclk
+ * functions. If any other timers used, another implementation should be
+ * placed in platform code.
+ */
+
+static inline u64 get_cntfrq(void)
+{
+	u64 cntfrq;
+	asm volatile("mrs %0, cntfrq_el0" : "=r" (cntfrq));
+	return cntfrq;
+}
+
+static inline u64 tick_to_time(u64 tick)
+{
+	tick *= CONFIG_SYS_HZ;
+	do_div(tick, get_cntfrq());
+	return tick;
+}
+
+static inline u64 time_to_tick(u64 time)
+{
+	time *= get_cntfrq();

arch/arm/cpu/armv8/timer.c line 44

Quoted 10 lines
arch/arm/cpu/armv8/timer.c new file +10 -0
+	do_div(time, CONFIG_SYS_HZ);
+	return time;
+}
+
+/*
+ * Generic timer implementation of get_tbclk()
+ */
+ulong __weak get_tbclk(void)
+{
+	return CONFIG_SYS_HZ;

You should return get_cntfreq here.

Quoted 21 lines
arch/arm/cpu/armv8/timer.c new file +21 -0
+}
+
+/*
+ * Generic timer implementation of get_timer()
+ */
+ulong __weak get_timer(ulong base)
+{
+	u64 cval;
+
+	isb();
+	asm volatile("mrs %0, cntpct_el0" : "=r" (cval));
+
+	return tick_to_time(cval) - base;
+}
+
+/*
+ * Generic timer implementation of get_ticks()
+ */
+unsigned long long __weak get_ticks(void)
+{
+	return get_timer(0);

arch/arm/cpu/armv8/timer.c line 75

Quoted 10 lines
arch/arm/cpu/armv8/timer.c new file +10 -0
+}
+
+/*
+ * Generic timer implementation of __udelay()
+ */
+void __weak __udelay(ulong usec)
+{
+	unsigned long ticks, limit;
+
+	limit = get_ticks() + usec/1000;

Your udelay implementation has 1 msec resolution. It should use the raw timer to get usec resolution.

Quoted 1,213 lines
arch/arm/cpu/armv8/timer.c new file +5 -0
+
+	do {
+		ticks = get_ticks();
+	} while (ticks < limit);
+}
arch/arm/cpu/armv8/tlb.S new file +30 -0
new file mode 100644
index 0000000..6bb1e1f
@@ -0,0 +1,30 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <version.h>
+#include <linux/linkage.h>
+#include <asm/macro.h>
+
+/*
+ * void __asm_invalidate_tlb_all(void)
+ *
+ * invalidate all tlb entries.
+ */
+ENTRY(__asm_invalidate_tlb_all)
+	switch_el1_el2 x9, 1f, 2f, 3f
+1:	tlbi	vmalle1
+	dsb	sy
+	isb
+	b	3f
+2:	tlbi	alle2
+	dsb	sy
+	isb
+3:
+	ret
+ENDPROC(__asm_invalidate_tlb_all)
arch/arm/cpu/armv8/u-boot.lds new file +71 -0
new file mode 100644
index 0000000..328d477
@@ -0,0 +1,71 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+OUTPUT_FORMAT("elf64-littleaarch64", "elf64-littleaarch64", "elf64-littleaarch64")
+OUTPUT_ARCH(aarch64)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(8);
+	.text :
+	{
+		*(.__image_copy_start)
+		CPUDIR/start.o (.text*)
+		*(.text*)
+	}
+
+	. = ALIGN(8);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(8);
+	.data : {
+		*(.data*)
+	}
+
+	. = ALIGN(8);
+
+	. = .;
+
+	. = ALIGN(8);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+
+	. = ALIGN(8);
+	.reloc : {
+		__rel_got_start = .;
+		*(.got)
+		__rel_got_end = .;
+	}
+
+	.image_copy_end :
+	{
+		*(.__image_copy_end)
+	}
+
+	_end = .;
+
+	. = ALIGN(8);
+	.bss : {
+		__bss_start = .;
+		*(.bss*)
+		 . = ALIGN(8);
+		__bss_end = .;
+	}
+
+	/DISCARD/ : { *(.dynsym) }
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
+}
arch/arm/include/asm/arch-armv8/gpio.h new file +11 -0
new file mode 100644
index 0000000..afe7ece
@@ -0,0 +1,11 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _ASM_ARMV8_GPIO_H_
+#define _ASM_ARMV8_GPIO_H_
+
+#endif	/* _ASM_ARMV8_GPIO_H_ */
arch/arm/include/asm/arch-armv8/mmu.h new file +110 -0
new file mode 100644
index 0000000..33b3246
@@ -0,0 +1,110 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _ASM_ARMV8_MMU_H_
+#define _ASM_ARMV8_MMU_H_
+
+#ifdef __ASSEMBLY__
+#define _AC(X, Y)	X
+#else
+#define _AC(X, Y)	(X##Y)
+#endif
+
+#define UL(x)		_AC(x, UL)
+
+/***************************************************************/
+/*
+ * The following definitions are related each other, shoud be
+ * calculated specifically.
+ */
+#define VA_BITS			(39)
+
+/* PAGE_SHIFT determines the page size */
+#undef  PAGE_SIZE
+#define PAGE_SHIFT		16
+#define PAGE_SIZE		(1 << PAGE_SHIFT)
+#define PAGE_MASK		(~(PAGE_SIZE-1))
+
+/*
+ * section address mask and size definitions.
+ */
+#define SECTION_SHIFT		29
+#define SECTION_SIZE		(UL(1) << SECTION_SHIFT)
+#define SECTION_MASK		(~(SECTION_SIZE-1))
+/***************************************************************/
+
+/*
+ * Memory types
+ */
+#define MT_DEVICE_NGNRNE	0
+#define MT_DEVICE_NGNRE		1
+#define MT_DEVICE_GRE		2
+#define MT_NORMAL_NC		3
+#define MT_NORMAL		4
+
+#define MEMORY_ATTRIBUTES	((0x00 << MT_DEVICE_NGNRNE*8) |	\
+				(0x04 << MT_DEVICE_NGNRE*8) |	\
+				(0x0c << MT_DEVICE_GRE*8) |	\
+				(0x44 << MT_NORMAL_NC*8) |	\
+				(0xff << MT_NORMAL*8))
+
+/*
+ * Hardware page table definitions.
+ *
+ * Level 2 descriptor (PMD).
+ */
+#define PMD_TYPE_MASK		(3 << 0)
+#define PMD_TYPE_FAULT		(0 << 0)
+#define PMD_TYPE_TABLE		(3 << 0)
+#define PMD_TYPE_SECT		(1 << 0)
+
+/*
+ * Section
+ */
+#define PMD_SECT_S		(3 << 8)
+#define PMD_SECT_AF		(1 << 10)
+#define PMD_SECT_NG		(1 << 11)
+#define PMD_SECT_PXN		(UL(1) << 53)
+#define PMD_SECT_UXN		(UL(1) << 54)
+
+/*
+ * AttrIndx[2:0]
+ */
+#define PMD_ATTRINDX(t)		((t) << 2)
+#define PMD_ATTRINDX_MASK	(7 << 2)
+
+/*
+ * TCR flags.
+ */
+#define TCR_T0SZ(x)		((64 - (x)) << 0)
+#define TCR_IRGN_NC		(0 << 8)
+#define TCR_IRGN_WBWA		(1 << 8)
+#define TCR_IRGN_WT		(2 << 8)
+#define TCR_IRGN_WBNWA		(3 << 8)
+#define TCR_IRGN_MASK		(3 << 8)
+#define TCR_ORGN_NC		(0 << 10)
+#define TCR_ORGN_WBWA		(1 << 10)
+#define TCR_ORGN_WT		(2 << 10)
+#define TCR_ORGN_WBNWA		(3 << 10)
+#define TCR_ORGN_MASK		(3 << 10)
+#define TCR_SHARED_NON		(0 << 12)
+#define TCR_SHARED_OUTER	(1 << 12)
+#define TCR_SHARED_INNER	(2 << 12)
+#define TCR_TG0_4K		(0 << 14)
+#define TCR_TG0_64K		(1 << 14)
+#define TCR_TG0_16K		(2 << 14)
+#define TCR_EL1_IPS_40BIT	(2 << 32)
+#define TCR_EL2_IPS_40BIT	(2 << 16)
+
+/* PTWs cacheable, inner/outer WBWA and non-shareable */
+#define TCR_FLAGS		(TCR_TG0_64K |		\
+				TCR_SHARED_NON |	\
+				TCR_ORGN_WBWA |		\
+				TCR_IRGN_WBWA |		\
+				TCR_T0SZ(VA_BITS))
+
+#endif /* _ASM_ARMV8_MMU_H_ */
arch/arm/include/asm/byteorder.h +12 -0
index c3489f1..71a9966 100644
@@ -23,10 +23,22 @@
 #  define __SWAB_64_THRU_32__
 #endif
 
+#ifdef	CONFIG_ARM64
+
+#ifdef __AARCH64EB__
+#include <linux/byteorder/big_endian.h>
+#else
+#include <linux/byteorder/little_endian.h>
+#endif
+
+#else	/* CONFIG_ARM64 */
+
 #ifdef __ARMEB__
 #include <linux/byteorder/big_endian.h>
 #else
 #include <linux/byteorder/little_endian.h>
 #endif
 
+#endif	/* CONFIG_ARM64 */
+
 #endif
arch/arm/include/asm/cache.h +5 -0
index 6d60a4a..ddebbc8 100644
@@ -11,6 +11,8 @@
 
 #include <asm/system.h>
 
+#ifndef CONFIG_ARM64
+
 /*
  * Invalidate L2 Cache using co-proc instruction
  */
@@ -28,6 +30,9 @@ void l2_cache_disable(void);
 void set_section_dcache(int section, enum dcache_option option);
 
 void dram_bank_mmu_setup(int bank);
+
+#endif
+
 /*
  * The current upper bound for ARM L1 data cache line sizes is 64 bytes.  We
  * use that value for aligning DMA buffers unless the board config has specified
arch/arm/include/asm/config.h +10 -0
index 99b703e..0ee131d 100644
@@ -9,4 +9,14 @@
 
 #define CONFIG_LMB
 #define CONFIG_SYS_BOOT_RAMDISK_HIGH
+
+#ifdef CONFIG_ARM64
+/*
+ * Currently, GOT is used to relocate u-boot and
+ * configuration CONFIG_NEEDS_MANUAL_RELOC is needed.
+ */
+#define CONFIG_NEEDS_MANUAL_RELOC
+#define CONFIG_PHYS_64BIT
+#endif
+
 #endif
arch/arm/include/asm/global_data.h +5 -1
index 79a9597..30a338e 100644
@@ -47,6 +47,10 @@ struct arch_global_data {
 
 #include <asm-generic/global_data.h>
 
-#define DECLARE_GLOBAL_DATA_PTR     register volatile gd_t *gd asm ("r8")
+#ifdef CONFIG_ARM64
+#define DECLARE_GLOBAL_DATA_PTR		register volatile gd_t *gd asm ("x18")
+#else
+#define DECLARE_GLOBAL_DATA_PTR		register volatile gd_t *gd asm ("r8")
+#endif
 
 #endif /* __ASM_GBL_DATA_H */
arch/arm/include/asm/io.h +9 -6
index 1fbc531..6a1f05a 100644
@@ -75,42 +75,45 @@ static inline phys_addr_t virt_to_phys(void * vaddr)
 #define __arch_putw(v,a)		(*(volatile unsigned short *)(a) = (v))
 #define __arch_putl(v,a)		(*(volatile unsigned int *)(a) = (v))
 
-extern inline void __raw_writesb(unsigned int addr, const void *data, int bytelen)
+extern inline void __raw_writesb(unsigned long addr, const void *data,
+				 int bytelen)
 {
 	uint8_t *buf = (uint8_t *)data;
 	while(bytelen--)
 		__arch_putb(*buf++, addr);
 }
 
-extern inline void __raw_writesw(unsigned int addr, const void *data, int wordlen)
+extern inline void __raw_writesw(unsigned long addr, const void *data,
+				 int wordlen)
 {
 	uint16_t *buf = (uint16_t *)data;
 	while(wordlen--)
 		__arch_putw(*buf++, addr);
 }
 
-extern inline void __raw_writesl(unsigned int addr, const void *data, int longlen)
+extern inline void __raw_writesl(unsigned long addr, const void *data,
+				 int longlen)
 {
 	uint32_t *buf = (uint32_t *)data;
 	while(longlen--)
 		__arch_putl(*buf++, addr);
 }
 
-extern inline void __raw_readsb(unsigned int addr, void *data, int bytelen)
+extern inline void __raw_readsb(unsigned long addr, void *data, int bytelen)
 {
 	uint8_t *buf = (uint8_t *)data;
 	while(bytelen--)
 		*buf++ = __arch_getb(addr);
 }
 
-extern inline void __raw_readsw(unsigned int addr, void *data, int wordlen)
+extern inline void __raw_readsw(unsigned long addr, void *data, int wordlen)
 {
 	uint16_t *buf = (uint16_t *)data;
 	while(wordlen--)
 		*buf++ = __arch_getw(addr);
 }
 
-extern inline void __raw_readsl(unsigned int addr, void *data, int longlen)
+extern inline void __raw_readsl(unsigned long addr, void *data, int longlen)
 {
 	uint32_t *buf = (uint32_t *)data;
 	while(longlen--)
arch/arm/include/asm/macro.h +39 -0
index ff13f36..db8869e 100644
@@ -54,5 +54,44 @@
 	bcs	1b
 .endm
 
+#ifdef CONFIG_ARM64
+/*
+ * Register aliases.
+ */
+lr	.req	x30
+
+/*
+ * Branch according to exception level
+ */
+.macro	switch_el1_el2, xreg, el1_label, el2_label, fail_label
+	mrs	\xreg, CurrentEL
+	cmp	\xreg, 0x4
+	b.eq	\el1_label
+	cmp	\xreg, 0x8
+	b.eq	\el2_label
+	b	\fail_label
+.endm
+
+/*
+ * Branch if current processor is a slave,
+ * choose processor with all zero affinity value as the master.
+ */
+.macro	branch_if_slave, xreg, slave_label
+	mrs	\xreg, mpidr_el1
+	tst	\xreg, #0xff		/* Test Affinity 0 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #8
+	tst	\xreg, #0xff		/* Test Affinity 1 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #8
+	tst	\xreg, #0xff		/* Test Affinity 2 */
+	b.ne	\slave_label
+	lsr	\xreg, \xreg, #16
+	tst	\xreg, #0xff		/* Test Affinity 3 */
+	b.ne	\slave_label
+.endm
+
+#endif /* CONFIG_ARM64 */
+
 #endif /* __ASSEMBLY__ */
 #endif /* __ASM_ARM_MACRO_H__ */
arch/arm/include/asm/posix_types.h +10 -0
index c412486..9ba9add 100644
@@ -13,6 +13,8 @@
 #ifndef __ARCH_ARM_POSIX_TYPES_H
 #define __ARCH_ARM_POSIX_TYPES_H
 
+#include <config.h>
+
 /*
  * This file is generally used by user-level software, so you need to
  * be a little careful about namespace pollution etc.  Also, we cannot
@@ -28,9 +30,17 @@ typedef int			__kernel_pid_t;
 typedef unsigned short		__kernel_ipc_pid_t;
 typedef unsigned short		__kernel_uid_t;
 typedef unsigned short		__kernel_gid_t;
+
+#ifdef	CONFIG_ARM64
+typedef unsigned long		__kernel_size_t;
+typedef long			__kernel_ssize_t;
+typedef long			__kernel_ptrdiff_t;
+#else	/* CONFIG_ARM64 */
 typedef unsigned int		__kernel_size_t;
 typedef int			__kernel_ssize_t;
 typedef int			__kernel_ptrdiff_t;
+#endif	/* CONFIG_ARM64 */
+
 typedef long			__kernel_time_t;
 typedef long			__kernel_suseconds_t;
 typedef long			__kernel_clock_t;
arch/arm/include/asm/proc-armv/ptrace.h +21 -0
index 79cc644..fd280cb 100644
@@ -12,6 +12,25 @@
 
 #include <linux/config.h>
 
+#ifdef CONFIG_ARM64
+
+#define PCMASK		0
+
+#ifndef __ASSEMBLY__
+
+/*
+ * This struct defines the way the registers are stored
+ * on the stack during an exception.
+ */
+struct pt_regs {
+	unsigned long elr;
+	unsigned long regs[31];
+};
+
+#endif	/* __ASSEMBLY__ */
+
+#else	/* CONFIG_ARM64 */
+
 #define USR26_MODE	0x00
 #define FIQ26_MODE	0x01
 #define IRQ26_MODE	0x02
@@ -106,4 +125,6 @@ static inline int valid_user_regs(struct pt_regs *regs)
 
 #endif	/* __ASSEMBLY__ */
 
+#endif	/* CONFIG_ARM64 */
+
 #endif
arch/arm/include/asm/proc-armv/system.h +58 -1
index b4cfa68..19b2b44 100644
@@ -15,6 +15,60 @@
 /*
  * Save the current interrupt enable state & disable IRQs
  */
+#ifdef CONFIG_ARM64
+
+/*
+ * Save the current interrupt enable state
+ * and disable IRQs/FIQs
+ */
+#define local_irq_save(flags)					\
+	({							\
+	asm volatile(						\
+	"mrs	%0, daif"					\
+	"msr	daifset, #3"					\
+	: "=r" (flags)						\
+	:							\
+	: "memory");						\
+	})
+
+/*
+ * restore saved IRQ & FIQ state
+ */
+#define local_irq_restore(flags)				\
+	({							\
+	asm volatile(						\
+	"msr	daif, %0"					\
+	:							\
+	: "r" (flags)						\
+	: "memory");						\
+	})
+
+/*
+ * Enable IRQs/FIQs
+ */
+#define local_irq_enable()					\
+	({							\
+	asm volatile(						\
+	"msr	daifclr, #3"					\
+	:							\
+	:							\
+	: "memory");						\
+	})
+
+/*
+ * Disable IRQs/FIQs
+ */
+#define local_irq_disable()					\
+	({							\
+	asm volatile(						\
+	"msr	daifset, #3"					\
+	:							\
+	:							\
+	: "memory");						\
+	})
+
+#else	/* CONFIG_ARM64 */
+
 #define local_irq_save(x)					\
 	({							\
 		unsigned long temp;				\
@@ -109,7 +163,10 @@
 	: "r" (x)						\
 	: "memory")
 
-#if defined(CONFIG_CPU_SA1100) || defined(CONFIG_CPU_SA110)
+#endif	/* CONFIG_ARM64 */
+
+#if defined(CONFIG_CPU_SA1100) || defined(CONFIG_CPU_SA110) || \
+	defined(CONFIG_ARM64)
 /*
  * On the StrongARM, "swp" is terminally broken since it bypasses the
  * cache totally.  This means that the cache becomes inconsistent, and,
arch/arm/include/asm/system.h +77 -0
index 760345f..e79f790 100644
@@ -1,6 +1,79 @@
 #ifndef __ASM_ARM_SYSTEM_H
 #define __ASM_ARM_SYSTEM_H
 
+#ifdef CONFIG_ARM64
+
+/*
+ * SCTLR_EL2 bits definitions
+ */
+#define CR_M		(1 << 0)	/* MMU enable			*/
+#define CR_A		(1 << 1)	/* Alignment abort enable	*/
+#define CR_C		(1 << 2)	/* Dcache enable		*/
+#define CR_SA		(1 << 3)	/* Stack Alignment Check Enable	*/
+#define CR_I		(1 << 12)	/* Icache enable		*/
+#define CR_WXN		(1 << 19)	/* Write Permision Imply XN	*/
+#define CR_EE		(1 << 25)	/* Exception (Big) Endian	*/
+
+#define PGTABLE_SIZE	(0x10000)
+
+#ifndef __ASSEMBLY__
+
+#define isb()				\
+	({asm volatile(			\
+	"isb" : : : "memory");		\
+	})
+
+#define wfi()				\
+	({asm volatile(			\
+	"wfi" : : : "memory");		\
+	})
+
+static inline unsigned int curent_el(void)
+{
+	unsigned int el;
+	asm volatile("mrs %0, CurrentEL" : "=r" (el) : : "cc");
+	return el >> 2;
+}
+
+static inline unsigned int get_sctlr(void)
+{
+	unsigned int el, val;
+
+	el = curent_el();
+	if (el == 1)
+		asm volatile("mrs %0, sctlr_el1" : "=r" (val) : : "cc");
+	else if (el == 2)
+		asm volatile("mrs %0, sctlr_el2" : "=r" (val) : : "cc");
+	else
+		panic("Not Supported Exception Level");
+
+	return val;
+}
+
+static inline void set_sctlr(unsigned int val)
+{
+	unsigned int el;
+
+	el = curent_el();
+	if (el == 1)
+		asm volatile("msr sctlr_el1, %0" : : "r" (val) : "cc");
+	else if (el == 2)
+		asm volatile("msr sctlr_el2, %0" : : "r" (val) : "cc");
+	else
+		panic("Not Supported Exception Level");
+
+	asm volatile("isb");
+}
+
+void __asm_flush_dcache_all(void);
+void __asm_flush_dcache_range(u64 start, u64 end);
+void __asm_invalidate_tlb_all(void);
+void __asm_invalidate_icache_all(void);
+
+#endif	/* __ASSEMBLY__ */
+
+#else /* CONFIG_ARM64 */
+
 #ifdef __KERNEL__
 
 #define CPU_ARCH_UNKNOWN	0
@@ -45,6 +118,8 @@
 #define CR_AFE	(1 << 29)	/* Access flag enable			*/
 #define CR_TE	(1 << 30)	/* Thumb exception enable		*/
 
+#define PGTABLE_SIZE		(4096 * 4)
+
 /*
  * This is used to ensure the compiler did actually allocate the register we
  * asked it for some inline assembly sequences.  Apparently we can't trust
@@ -132,4 +207,6 @@ void mmu_page_table_flush(unsigned long start, unsigned long stop);
 
 #endif /* __KERNEL__ */
 
+#endif /* CONFIG_ARM64 */
+
 #endif
arch/arm/include/asm/types.h +4 -0
index 71dc049..2326420 100644
@@ -39,7 +39,11 @@ typedef unsigned int u32;
 typedef signed long long s64;
 typedef unsigned long long u64;
 
+#ifdef	CONFIG_ARM64
+#define BITS_PER_LONG 64
+#else	/* CONFIG_ARM64 */
 #define BITS_PER_LONG 32
+#endif	/* CONFIG_ARM64 */
 
 /* Dma addresses are 32-bits wide.  */
 
arch/arm/include/asm/u-boot.h +4 -0
index 2b5fce8..cb81232 100644
@@ -44,6 +44,10 @@ typedef struct bd_info {
 #endif /* !CONFIG_SYS_GENERIC_BOARD */
 
 /* For image.h:image_check_target_arch() */
+#ifndef CONFIG_ARM64
 #define IH_ARCH_DEFAULT IH_ARCH_ARM
+#else
+#define IH_ARCH_DEFAULT IH_ARCH_ARM64
+#endif
 
 #endif	/* _U_BOOT_H_ */
arch/arm/include/asm/unaligned.h +1 -1
index 44593a8..0a228fb 100644
@@ -8,7 +8,7 @@
 /*
  * Select endianness
  */
-#ifndef __ARMEB__
+#if __BYTE_ORDER == __LITTLE_ENDIAN
 #define get_unaligned	__get_unaligned_le
 #define put_unaligned	__put_unaligned_le
 #else
arch/arm/lib/Makefile +14 -0
index 4e78723..03c31c7 100644
@@ -10,6 +10,9 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(ARCH).o
 LIBGCC	= $(obj)libgcc.o
 
+ifdef CONFIG_ARM64
+SOBJS-y += crt0_64.o
+else
 GLSOBJS	+= _ashldi3.o
 GLSOBJS	+= _ashrdi3.o
 GLSOBJS	+= _divsi3.o
@@ -21,9 +24,14 @@ GLSOBJS	+= _umodsi3.o
 GLCOBJS	+= div0.o
 
 SOBJS-y += crt0.o
+endif
 
 ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_ARM64
+SOBJS-y += relocate_64.o
+else
 SOBJS-y += relocate.o
+endif
 ifndef CONFIG_SYS_GENERIC_BOARD
 COBJS-y	+= board.o
 endif
@@ -38,11 +46,17 @@ else
 COBJS-$(CONFIG_SPL_FRAMEWORK) += spl.o
 endif
 
+ifdef CONFIG_ARM64
+COBJS-y	+= interrupts_64.o
+else
 COBJS-y	+= interrupts.o
+endif
 COBJS-y	+= reset.o
 
 COBJS-y	+= cache.o
+ifndef CONFIG_ARM64
 COBJS-y	+= cache-cp15.o
+endif
 
 SRCS	:= $(GLSOBJS:.o=.S) $(GLCOBJS:.o=.c) \
 	   $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
arch/arm/lib/board.c +23 -2
index 34f50b0..d6d0833 100644
@@ -344,7 +344,7 @@ void board_init_f(ulong bootflag)
 
 #if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
 	/* reserve TLB table */
-	gd->arch.tlb_size = 4096 * 4;
+	gd->arch.tlb_size = PGTABLE_SIZE;
 	addr -= gd->arch.tlb_size;
 
 	/* round down to next 64 kB limit */
@@ -419,6 +419,7 @@ void board_init_f(ulong bootflag)
 	}
 #endif
 
+#ifndef CONFIG_ARM64
 	/* setup stackpointer for exeptions */
 	gd->irq_sp = addr_sp;
 #ifdef CONFIG_USE_IRQ
@@ -431,6 +432,10 @@ void board_init_f(ulong bootflag)
 
 	/* 8-byte alignment for ABI compliance */
 	addr_sp &= ~0x07;
+#else	/* CONFIG_ARM64 */
+	/* 16-byte alignment for ABI compliance */
+	addr_sp &= ~0x0f;
+#endif	/* CONFIG_ARM64 */
 #else
 	addr_sp += 128;	/* leave 32 words for abort-stack   */
 	gd->irq_sp = addr_sp;
@@ -513,7 +518,15 @@ void board_init_r(gd_t *id, ulong dest_addr)
 	ulong flash_size;
 #endif
 
+	/*
+	 * Relocate routines of serial_device first so that
+	 * printf access the correct puts function. This is critical
+	 * when CONFIG_NEEDS_MANUAL_RELOC is needed.
+	 */
+	serial_initialize();
+
 	gd->flags |= GD_FLG_RELOC;	/* tell others: relocation done */
+
 	bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
 
 	monitor_flash_len = _end_ofs;
@@ -523,6 +536,15 @@ void board_init_r(gd_t *id, ulong dest_addr)
 
 	debug("monitor flash len: %08lX\n", monitor_flash_len);
 	board_init();	/* Setup chipselects */
+
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+	/*
+	 * We have to relocate the command table manually
+	 */
+	fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd),
+			ll_entry_count(cmd_tbl_t, cmd));
+#endif /* CONFIG_NEEDS_MANUAL_RELOC */
+
 	/*
 	 * TODO: printing of the clock inforamtion of the board is now
 	 * implemented as part of bdinfo command. Currently only support for
@@ -532,7 +554,6 @@ void board_init_r(gd_t *id, ulong dest_addr)
 #ifdef CONFIG_CLOCKS
 	set_cpu_clk_info(); /* Setup clock information */
 #endif
-	serial_initialize();
 
 	debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
 
arch/arm/lib/bootm.c +16 -0
index eefb456..26e85f0 100644
@@ -222,6 +222,21 @@ static void boot_prep_linux(bootm_headers_t *images)
 /* Subcommand: GO */
 static void boot_jump_linux(bootm_headers_t *images, int flag)
 {
+#ifdef CONFIG_ARM64
+	void (*kernel_entry)(void *fdt_addr);
+	int fake = (flag & BOOTM_STATE_OS_FAKE_GO);
+
+	kernel_entry = (void (*)(void *fdt_addr))images->ep;
+
+	debug("## Transferring control to Linux (at address %lx)...\n",
+		(ulong) kernel_entry);
+	bootstage_mark(BOOTSTAGE_ID_RUN_OS);
+
+	announce_and_cleanup(fake);
+
+	if (!fake)
+		kernel_entry(images->ft_addr);
+#else
 	unsigned long machid = gd->bd->bi_arch_number;
 	char *s;
 	void (*kernel_entry)(int zero, int arch, uint params);
@@ -248,6 +263,7 @@ static void boot_jump_linux(bootm_headers_t *images, int flag)
 
 	if (!fake)
 		kernel_entry(0, machid, r2);
+#endif
 }
 
 /* Main Entry point for arm bootm implementation
arch/arm/lib/crt0_64.S new file +116 -0
new file mode 100644
index 0000000..ddd46eb
@@ -0,0 +1,116 @@
+/*
+ * crt0 - C-runtime startup Code for AArch64 U-Boot
+ *
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * (C) Copyright 2012
+ * Albert ARIBAUD <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/macro.h>
+#include <linux/linkage.h>
+
+/*
+ * This file handles the target-independent stages of the U-Boot
+ * start-up where a C runtime environment is needed. Its entry point
+ * is _main and is branched into from the target's start.S file.
+ *
+ * _main execution sequence is:
+ *
+ * 1. Set up initial environment for calling board_init_f().
+ *    This environment only provides a stack and a place to store
+ *    the GD ('global data') structure, both located in some readily
+ *    available RAM (SRAM, locked cache...). In this context, VARIABLE
+ *    global data, initialized or not (BSS), are UNAVAILABLE; only
+ *    CONSTANT initialized data are available.
+ *
+ * 2. Call board_init_f(). This function prepares the hardware for
+ *    execution from system RAM (DRAM, DDR...) As system RAM may not
+ *    be available yet, , board_init_f() must use the current GD to
+ *    store any data which must be passed on to later stages. These
+ *    data include the relocation destination, the future stack, and
+ *    the future GD location.
+ *
+ * (the following applies only to non-SPL builds)
+ *
+ * 3. Set up intermediate environment where the stack and GD are the
+ *    ones allocated by board_init_f() in system RAM, but BSS and
+ *    initialized non-const data are still not available.
+ *
+ * 4. Call relocate_code(). This function relocates U-Boot from its
+ *    current location into the relocation destination computed by
+ *    board_init_f().
+ *
+ * 5. Set up final environment for calling board_init_r(). This
+ *    environment has BSS (initialized to 0), initialized non-const
+ *    data (initialized to their intended value), and stack in system
+ *    RAM. GD has retained values set by board_init_f(). Some CPUs
+ *    have some work left to do at this point regarding memory, so
+ *    call c_runtime_cpu_setup.
+ *
+ * 6. Branch to board_init_r().
+ */
+
+ENTRY(_main)
+
+/*
+ * Set up initial C runtime environment and call board_init_f(0).
+ */
+	ldr	x0, =(CONFIG_SYS_INIT_SP_ADDR)
+	sub	x0, x0, #GD_SIZE	/* allocate one GD above SP */
+	bic	sp, x0, #0xf	/* 16-byte alignment for ABI compliance */
+	mov	x18, sp			/* GD is above SP */
+	mov	x0, #0
+	bl	board_init_f
+
+/*
+ * Set up intermediate environment (new sp and gd) and call
+ * relocate_code(addr_moni). Trick here is that we'll return
+ * 'here' but relocated.
+ */
+	ldr	x0, [x18, #GD_START_ADDR_SP]	/* x0 <- gd->start_addr_sp */
+	bic	sp, x0, #0xf	/* 16-byte alignment for ABI compliance */
+	ldr	x18, [x18, #GD_BD]		/* x18 <- gd->bd */
+	sub	x18, x18, #GD_SIZE		/* new GD is below bd */
+
+	adr	lr, relocation_return
+	ldr	x9, [x18, #GD_RELOC_OFF]	/* x9 <- gd->reloc_off */
+	add	lr, lr, x9	/* new return address after relocation */
+	ldr	x0, [x18, #GD_RELOCADDR]	/* x0 <- gd->relocaddr */
+	b	relocate_code
+
+relocation_return:
+
+/*
+ * Set up final (full) environment
+ */
+	bl	c_runtime_cpu_setup		/* still call old routine */
+
+/*
+ * Clear BSS section
+ */
+	ldr	x9, [x18, #GD_RELOC_OFF]	/* x9 <- gd->reloc_off */
+	ldr	x0, =__bss_start
+	add	x0, x0, x9			/* x0 <- __bss_start in RAM */
+	ldr	x1, =__bss_end
+	add	x1, x1, x9			/* x1 <- __bss_end in RAM */
+	mov	x2, #0
+clear_loop:
+	str	x2, [x0]
+	add	x0, x0, #8
+	cmp	x0, x1
+	b.lo	clear_loop
+
+	/* call board_init_r(gd_t *id, ulong dest_addr) */
+	mov	x0, x18				/* gd_t */
+	ldr	x1, [x18, #GD_RELOCADDR]	/* dest_addr */
+	b	board_init_r			/* PC relative jump */
+
+	/* NOTREACHED - board_init_r() does not return */
+
+ENDPROC(_main)
arch/arm/lib/interrupts_64.c new file +120 -0
new file mode 100644
index 0000000..b476722
@@ -0,0 +1,120 @@
+/*
+ * (C) Copyright 2013
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/compiler.h>
+
+
+int interrupt_init(void)
+{
+	return 0;
+}
+
+void enable_interrupts(void)
+{
+	return;
+}
+
+int disable_interrupts(void)
+{
+	return 0;
+}
+
+void show_regs(struct pt_regs *regs)
+{
+	int i;
+
+	printf("ELR:     %lx\n", regs->elr);
+	printf("LR:      %lx\n", regs->regs[30]);
+	for (i = 0; i < 29; i += 2)
+		printf("x%-2d: %016lx x%-2d: %016lx\n",
+		       i, regs->regs[i], i+1, regs->regs[i+1]);
+	printf("\n");
+}
+
+/*
+ * do_bad_sync handles the impossible case in the Synchronous Abort vector.
+ */
+void do_bad_sync(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("Bad mode in \"Synchronous Abort\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_bad_irq handles the impossible case in the Irq vector.
+ */
+void do_bad_irq(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("Bad mode in \"Irq\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_bad_fiq handles the impossible case in the Fiq vector.
+ */
+void do_bad_fiq(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("Bad mode in \"Fiq\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_bad_error handles the impossible case in the Error vector.
+ */
+void do_bad_error(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("Bad mode in \"Error\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_sync handles the Synchronous Abort exception.
+ */
+void do_sync(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("\"Synchronous Abort\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_irq handles the Irq exception.
+ */
+void do_irq(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("\"Irq\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_fiq handles the Fiq exception.
+ */
+void do_fiq(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("\"Fiq\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
+
+/*
+ * do_error handles the Error exception.
+ * Errors are more likely to be processor specific,
+ * it is defined with weak attribute and can be redefined
+ * in processor specific code.
+ */
+void __weak do_error(struct pt_regs *pt_regs, unsigned int esr)
+{
+	printf("\"Error\" handler, esr 0x%08x\n", esr);
+	show_regs(pt_regs);
+	panic("Resetting CPU ...\n");
+}
arch/arm/lib/relocate_64.S new file +57 -0
new file mode 100644
index 0000000..29c3239
@@ -0,0 +1,57 @@
+/*
+ * relocate - common relocation function for AArch64 U-Boot
+ *
+ * (C) Copyright 2013
+ * Albert ARIBAUD <[email protected]>
+ * David Feng <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <linux/linkage.h>
+
+/*
+ * void relocate_code (addr_moni)
+ *
+ * This function relocates the monitor code.
+ *
+ * NOTE:
+ * GOT is used and configuration CONFIG_NEEDS_MANUAL_RELOC is needed.
+ */
+ENTRY(relocate_code)
+	/*
+	 * Copy u-boot from flash to RAM
+	 */
+	ldr	x1, =__image_copy_start	/* x1 <- copy source */
+	cmp	x1, x0
+	b.eq	relocate_done		/* skip relocation */
+	mov	x2, x0			/* x2 <- copy destination */
+	ldr	x3, =__image_copy_end	/* x3 <- source end address */
+
+copy_loop:
+	ldp	x10, x11, [x1], #16	/* copy from source address [x1] */
+	stp	x10, x11, [x2], #16	/* copy to   target address [x2] */
+	cmp	x1, x3			/* until source end address [x3] */
+	b.lo	copy_loop
+
+	/*
+	 * Fix .reloc relocations
+	 */
+	ldr	x9, [x18, #GD_RELOC_OFF]/* x9 <- relocation offset */
+	ldr	x1, =__rel_got_start	/* x1 <- rel got start ofs */
+	add	x1, x1, x9		/* x1 <- rel got start in RAM */
+	ldr	x2, =__rel_got_end	/* x2 <- rel got end ofs */
+	add	x2, x2, x9		/* x2 <- rel got end in RAM */
+fixloop:
+	ldr	x10, [x1]
+	add	x10, x10, x9		/* x10 <- address to be fixed up */
+	str	x10, [x1]
+	add	x1, x1, #8		/* each got entry is 8 bytes */
+	cmp	x1, x2
+	b.lo	fixloop
+
+relocate_done:
+	ret
+ENDPROC(relocate_code)
common/image.c +1 -0
index b0ae58f..4145354 100644
@@ -81,6 +81,7 @@ static const table_entry_t uimage_arch[] = {
 	{	IH_ARCH_NDS32,		"nds32",	"NDS32",	},
 	{	IH_ARCH_OPENRISC,	"or1k",		"OpenRISC 1000",},
 	{	IH_ARCH_SANDBOX,	"sandbox",	"Sandbox",	},
+	{	IH_ARCH_ARM64,		"arm64",	"AArch64",	},
 	{	-1,			"",		"",		},
 };
 
doc/README.arm64 new file +1 -0
new file mode 100644
index 0000000..746ce6a
@@ -0,0 +1,33 @@
+U-boot for arm64

doc/README.arm64 line 11

Quoted 10 lines
doc/README.arm64 new file +10 -0
+
+Summary
+=======
+No hardware platform of arm64 is available now. The u-boot is
+simulated on Foundation Model and Fast Model for ARMv8.
+
+Notes
+=====
+
+1. Currenly, u-boot could be running at EL1 or EL2.

s/Currenly/Currently/

doc/README.arm64 line 13

Quoted 2 lines
doc/README.arm64 new file +2 -0
+
+2. Currenly, U-boot for arm64 is compiled with AArch64-gcc. AArch64-gcc

s/Currenly/Currently/

Quoted 66 lines
doc/README.arm64 new file +20 -0
+   use rela relocation format, it cannot be relocated during running. So,
+   GOT is used to relocate u-boot and CONFIG_NEEDS_MANUAL_RELOC is needed.
+
+3. Fdt should be placed at a 2-megabyte boundary and within the first 512
+   megabytes from the start of the kernel image. So, fdt_high should be
+   defined specially.
+   Please reference linux/Documentation/arm64/booting.txt for detail.
+
+4. Generic board is supported.
+
+5. CONFIG_ARM64 instead of CONFIG_ARMV8 is used to distinguish aarch64 and
+   aarch32 specific codes.
+
+Contributor
+===========
+   Tom Rini       <[email protected]>
+   Scott Wood     <[email protected]>
+   Simon Glass    <[email protected]>
+   Sharma Bhupesh <[email protected]>
+   Rob Herring    <[email protected]>
examples/standalone/stubs.c +15 -0
index 8fb1765..fc5d7ef 100644
@@ -39,6 +39,20 @@ gd_t *global_data;
 "	bctr\n"				\
 	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "r11");
 #elif defined(CONFIG_ARM)
+#ifdef CONFIG_ARM64
+/*
+ * x18 holds the pointer to the global_data, x9 is a call-clobbered
+ * register
+ */
+#define EXPORT_FUNC(x) \
+	asm volatile (			\
+"	.globl " #x "\n"		\
+#x ":\n"				\
+"	ldr	x9, [x18, %0]\n"		\
+"	ldr	x9, [x9, %1]\n"		\
+"	br	x9\n"		\
+	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "x9");
+#else
 /*
  * r8 holds the pointer to the global_data, ip is a call-clobbered
  * register
@@ -50,6 +64,7 @@ gd_t *global_data;
 "	ldr	ip, [r8, %0]\n"		\
 "	ldr	pc, [ip, %1]\n"		\
 	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "ip");
+#endif
 #elif defined(CONFIG_MIPS)
 /*
  * k0 ($26) holds the pointer to the global_data; t9 ($25) is a call-
include/image.h +1 -0
index ee6eb8d..7de2bb2 100644
@@ -156,6 +156,7 @@ struct lmb;
 #define IH_ARCH_SANDBOX		19	/* Sandbox architecture (test only) */
 #define IH_ARCH_NDS32	        20	/* ANDES Technology - NDS32  */
 #define IH_ARCH_OPENRISC        21	/* OpenRISC 1000  */
+#define IH_ARCH_ARM64		22	/* ARM64	*/
 
 /*
  * Image Types
#9 lore raw

PATCH v13 1/6 core support of arm64

Quoted 21 lines · Rob Herring
Quoted 5 lines · fenghua at phytium.com.cn

From: David Feng <[email protected]>

---
 arch/arm/config.mk                      |    4 +

FYI, some recent mainline changes to config.mk break the build for me.

Quoted 12 lines
 arch/arm/cpu/armv8/Makefile             |   38 +++++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 ++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 +++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++++++
 arch/arm/cpu/armv8/exceptions.S         |  115 +++++++++++++++
 arch/arm/cpu/armv8/start.S              |  234 +++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 +++++++++++
 arch/arm/cpu/armv8/tlb.S                |   30 ++++
 arch/arm/cpu/armv8/u-boot.lds           |   71 ++++++++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 ++
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 +++++++++++++++

Also, this directory is mutually exclusive with arch-${soc}. I think this should be moved up a level. gpio.h is probably fine as a default version.

Rob

#10 lore raw

PATCH v13 1/6 core support of arm64

Quoted 23 lines · Rob Herring
Quoted 21 lines · Rob Herring
Quoted 5 lines · fenghua at phytium.com.cn

From: David Feng <[email protected]>

---
 arch/arm/config.mk                      |    4 +

FYI, some recent mainline changes to config.mk break the build for me.

Quoted 12 lines
 arch/arm/cpu/armv8/Makefile             |   38 +++++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 ++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 +++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++++++
 arch/arm/cpu/armv8/exceptions.S         |  115 +++++++++++++++
 arch/arm/cpu/armv8/start.S              |  234 +++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 +++++++++++
 arch/arm/cpu/armv8/tlb.S                |   30 ++++
 arch/arm/cpu/armv8/u-boot.lds           |   71 ++++++++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 ++
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 +++++++++++++++
Quoted 4 lines

Also, this directory is mutually exclusive with arch-${soc}. I think this should be moved up a level. gpio.h is probably fine as a default version.

I am also concerned about gpio.h. I am forced to create a gpio.h file even I don't use it when I add soc for armv8.

York

#11 lore raw

PATCH v13 1/6 core support of arm64

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 24 lines · York Sun
Quoted 23 lines · Rob Herring
Quoted 21 lines · Rob Herring
Quoted 5 lines · fenghua at phytium.com.cn

From: David Feng <[email protected]>

---
 arch/arm/config.mk                      |    4 +

FYI, some recent mainline changes to config.mk break the build for me.

Quoted 12 lines
 arch/arm/cpu/armv8/Makefile             |   38 +++++
 arch/arm/cpu/armv8/cache.S              |  130 +++++++++++++++++
 arch/arm/cpu/armv8/cache_v8.c           |  218 ++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/config.mk            |   16 +++
 arch/arm/cpu/armv8/cpu.c                |   67 +++++++++
 arch/arm/cpu/armv8/exceptions.S         |  115 +++++++++++++++
 arch/arm/cpu/armv8/start.S              |  234 +++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/timer.c              |   80 +++++++++++
 arch/arm/cpu/armv8/tlb.S                |   30 ++++
 arch/arm/cpu/armv8/u-boot.lds           |   71 ++++++++++
 arch/arm/include/asm/arch-armv8/gpio.h  |   11 ++
 arch/arm/include/asm/arch-armv8/mmu.h   |  110 +++++++++++++++
Quoted 7 lines
Quoted 4 lines

Also, this directory is mutually exclusive with arch-${soc}. I think this should be moved up a level. gpio.h is probably fine as a default version.

I am also concerned about gpio.h. I am forced to create a gpio.h file even I don't use it when I add soc for armv8.

Yes, gpio.h belongs elsewhere, and we should not be making symlinks for arch-armv8, we should just have asm/armv8/ and asm/armv7/ and reference them directly,

- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/

iQIcBAEBAgAGBQJSTefxAAoJENk4IS6UOR1WzkgQAK61cVCUk2ouSKChMs0bZkIf xjiNzN+YSAjE49P5APl6Ai6XbIWUVNWlZnRwbZC3rAl7QsTM0c8tcx8G3e54QDQT pvbH4nvpj79Zjkc48Td7C5ZP+pw+vXshkXnUJrGKQe5AUPnP6DFGbILHn1gcSDj9 IusRDO1+sr0zuyU9XTKopmWQvPddFoUUwsA3KaFAoqDQeuBWW/lbYiETbDRnPGdz e9hmq7sX9j6iE2Q5Vut8OuiZdvF677AL2eoFhk4NZ25KDaTP0cAltvpFcrZheGrt vBKkpAFiKeuZG6CDEhJu22OHGLrQb266WpqqzHyGnAoqYpUahfxOfP+Z/31SaNBz T1TnPfgNTCmy5LxG/msXeYXR6CJg0uIXvQnBJk/oRAA+xyxEwIeEXpmMyTtC2ZPy cHeBgeLUo2QetMtMEOyrnt/xauOjRU5s252qniRPfaSLOSbyF4ElxDMNcU0amOYH ay+bp7cgmsIuMJV/Oza9k/SH+wkMlERud5gY85U3MUmNUSCt3UfOdwTZSOMnAucM //Dli/bsD+MegfO+aXG/nDWDPkpIqfFwHYlbrLORD5LhUFPqTliZepj9U5ACFBc6 b6H0crU134XBfsWtlDs3ZvPFberP9THU0tmreAwPtDtAKkl2SG0VqV+P4obxXH/G o4V7jZg+eLHSm1mMYgmz
=WywE
-----END PGP SIGNATURE-----