ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.
---
Rebase to for_3.13/dts
arch/arm/boot/dts/dra7-evm.dts | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-)
arch/arm/boot/dts/dra7-evm.dts +6 -0
@@ -250,3 +250,9 @@ pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; }; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; +};
Signature · 1 line
1.7.5.4
PATCH 2/2 ARM: dts: dra7-evm: Add mmc2 node for eMMC support
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
---
Rebase to for_3.13/dts
and removed ti,non-removable
arch/arm/boot/dts/dra7-evm.dts | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-)
arch/arm/boot/dts/dra7-evm.dts +13 -0
@@ -17,6 +17,13 @@ device_type = "memory"; reg = <0x80000000 0x60000000>; /* 1536 MB */ }; + + mmc2_3v3: fixedregulator-mmc2 { + compatible = "regulator-fixed"; + regulator-name = "mmc2_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core {
@@ -256,3 +263,9 @@ vmmc-supply = <&ldo1_reg>; bus-width = <4>; }; + +&mmc2 { + status = "okay"; + vmmc-supply = <&mmc2_3v3>; + bus-width = <8>; +};
Signature · 1 line
1.7.5.4
PATCH 2/2 ARM: dts: dra7-evm: Add mmc2 node for eMMC support
Quoted 31 lines · Balaji T K
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.Signed-off-by Balaji T K <[email protected]>---
Rebase to for_3.13/dts
and removed ti,non-removablearch/arm/boot/dts/dra7-evm.dts | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-)arch/arm/boot/dts/dra7-evm.dts +7
-0@@ -17,6 +17,13 @@ device_type = "memory"; reg = <0x80000000 0x60000000>; /* 1536 MB */ }; + + mmc2_3v3: fixedregulator-mmc2 { + compatible = "regulator-fixed"; + regulator-name = "mmc2_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core {
arch/arm/boot/dts/dra7-evm.dts line 271
Quoted 9 lines
arch/arm/boot/dts/dra7-evm.dts +6
-0@@ -256,3 +263,9 @@ vmmc-supply = <&ldo1_reg>; bus-width = <4>; }; + +&mmc2 { + status = "okay"; + vmmc-supply = <&mmc2_3v3>; + bus-width = <8>; +};
boot tested on DRA7-EVM
voltage rail is correct based on schematics(rev d1) too.
Signature · 2 lines
Regards, Nishanth Menon
PATCH 2/2 ARM: dts: dra7-evm: Add mmc2 node for eMMC support
In reply to Balaji T KQuoted 4 lines · Balaji T K
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.Signed-off-by Balaji T K <[email protected]>
Thanks,
Sekhar
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
In reply to Balaji T KQuoted 18 lines · Balaji T K
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.Signed-off-by Balaji T K <[email protected]>---
Rebase to for_3.13/dtsarch/arm/boot/dts/dra7-evm.dts | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-)arch/arm/boot/dts/dra7-evm.dts +0
-0
arch/arm/boot/dts/dra7-evm.dts line 258
Quoted 9 lines
arch/arm/boot/dts/dra7-evm.dts +6
-0@@ -250,3 +250,9 @@ pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; }; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; +};
boot tested on DRA7-EVM
voltage rail is correct based on schematics(rev d1) too (LDO1->MMC1_3V3->SDcard).
Signature · 2 lines
Regards, Nishanth Menon
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
In reply to Balaji T KQuoted 6 lines · Balaji T K
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.Signed-off-by Balaji T K <[email protected]>
Thanks,
Sekhar
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
Quoted 10 lines · Sekhar Nori
Quoted 6 lines · Balaji T K
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.Signed-off-by Balaji T K <[email protected]>Acked-by Sekhar Nori <[email protected]>
Hi Benoit,
Can you let me know if you have any comments on this patch series?
Thanks and Regards
Balaji T K
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
Hi Balaji,
Quoted 7 lines · Balaji T K
Quoted 6 lines · Sekhar Nori
Quoted 5 lines · Balaji T K
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Balaji T K <[email protected]>Acked-by Sekhar Nori <[email protected]>Hi Benoit,
Can you let me know if you have any comments on this patch series?
The series looks good, and I've just applied it for 3.13.
Thanks,
Benoit
PATCH v2 1/2 ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
Quoted 12 lines · Benoit Cousson
Hi Balaji,
Quoted 9 lines · Balaji T K
Quoted 8 lines · Sekhar Nori
Quoted 6 lines · Balaji T K
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator.Signed-off-by Balaji T K <[email protected]>
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
Acked-by Sekhar Nori <[email protected]>Hi Benoit,
Can you let me know if you have any comments on this patch series?
The series looks good, and I've just applied it for 3.13.
Thanks Benoit
- Balaji T K