ARM: dts: Add initial support for cm-fx6
PATCH 1/1 ARM: dts: Add initial support for cm-fx6
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIE
This patch allows to boot up the module, configures the serial console, the Ethernet adapter and the hearbeat led.
--- arch/arm/boot/dts/cm-fx6.dts | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 arch/arm/boot/dts/cm-fx6.dts
arch/arm/boot/dts/cm-fx6.dts new file +51 -0
@@ -0,0 +1,51 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + debug-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +};
Signature · 1 line
1.7.9.5
PATCH 1/1 ARM: dts: Add initial support for cm-fx6
Quoted 82 lines · Valentin Raevsky
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIEThis patch allows to boot up the module, configures the serial console, the Ethernet adapter and the hearbeat led.
Signed-off-by Valentin Raevsky <[email protected]>Acked-by Igor Grinberg <[email protected]>--- arch/arm/boot/dts/cm-fx6.dts | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 arch/arm/boot/dts/cm-fx6.dtsarch/arm/boot/dts/cm-fx6.dts new file +51
-1@@ -0,0 +1,51 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + debug-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; --
Quoted 2 lines
1.7.9.5
Hi Valentin,
Completely skipped over this, as I wasn't sure what the cm-fx6 was. Could we maybe mention that this is commonly referred to as the Utilite?
Signature · 4 lines
This e-mail and any attachments are for the sole use of the intended
recipients(s) and may be confidential. Use of any Pwnie Express product
signifies your agreement to the Rapid Focus Security EULA<http://pwnieexpress.com/pdfs/RFSEULA.pdf>and is subject to export controls under the U.S. Commerce Department's
Export Administration Regulations ("EAR").PATCH 1/1 ARM: dts: Add initial support for cm-fx6
Quoted 89 lines · Steev Klimaszewski
Quoted 82 lines · Valentin Raevsky
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIEThis patch allows to boot up the module, configures the serial console, the Ethernet adapter and the hearbeat led.
Signed-off-by Valentin Raevsky <[email protected]>Acked-by Igor Grinberg <[email protected]>--- arch/arm/boot/dts/cm-fx6.dts | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+)create mode 100644
arch/arm/boot/dts/cm-fx6.dtsarch/arm/boot/dts/cm-fx6.dts new file +51
-1@@ -0,0 +1,51 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + debug-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; --Quoted 2 lines
1.7.9.5
Hi Valentin,
Quoted 4 lines
Completely skipped over this, as I wasn't sure what the cm-fx6 was. Could we maybe mention that this is commonly referred to as the Utilite?
Utilite actually consists of two boards:
cm-fx6 -- system on module, sb-fx6m -- base board (extension board). But you are right, I should have mentioned it.
I will do it in v2.
Regards,
Valentin.
PATCH 1/1 ARM: dts: Add initial support for cm-fx6
In reply to Valentin RaevskyQuoted 17 lines · Valentin Raevsky
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIEThis patch allows to boot up the module, configures the serial console, the Ethernet adapter and the hearbeat led.
Quoted 6 lines
Signed-off-by Valentin Raevsky <[email protected]>Acked-by Igor Grinberg <[email protected]>--- arch/arm/boot/dts/cm-fx6.dts | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 arch/arm/boot/dts/cm-fx6.dts
Please name the file with 'imx6q-' prefix, and add dtb target into arch/arm/boot/dts/Makefile.
Quoted 37 lines
arch/arm/boot/dts/cm-fx6.dts new file +30
-0@@ -0,0 +1,51 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + debug-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + };
arch/arm/boot/dts/cm-fx6.dts line 40
Quoted 10 lines
arch/arm/boot/dts/cm-fx6.dts new file +10
-0+ }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "okay"; +}; + +&fec {
Please sort the nodes alphabetically in label names.
Shawn
Quoted 19 lines
arch/arm/boot/dts/cm-fx6.dts new file +11
-0+ pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +};Signature · 7 lines
1.7.9.5 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 1/1 ARM: dts: Add initial support for cm-fx6
Quoted 25 lines · Shawn Guo
Quoted 17 lines · Valentin Raevsky
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIEThis patch allows to boot up the module, configures the serial console, the Ethernet adapter and the hearbeat led.
Quoted 6 lines
Signed-off-by Valentin Raevsky <[email protected]>Acked-by Igor Grinberg <[email protected]>--- arch/arm/boot/dts/cm-fx6.dts | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+)create mode 100644
arch/arm/boot/dts/cm-fx6.dts
Quoted 2 lines
Please name the file with 'imx6q-' prefix, and add dtb target into
arch/arm/boot/dts/Makefile.
thatnks, got it. will be in v2.
Quoted 42 lines
Quoted 42 lines
arch/arm/boot/dts/cm-fx6.dts new file +34
-0@@ -0,0 +1,51 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + debug-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpmi {
Quoted 8 lines
arch/arm/boot/dts/cm-fx6.dts line 40
Quoted 6 lines
arch/arm/boot/dts/cm-fx6.dts new file +6
-0+ pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "okay"; +}; + +&fec {Please sort the nodes alphabetically in label names.
got it. will be in v2.
Quoted 23 lines
Shawn
Quoted 19 lines
arch/arm/boot/dts/cm-fx6.dts new file +11
-1+ pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; --1.7.9.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel