Initial support for I.MX6 SabreAuto board
PATCH 1/2 Initial support for I.MX6 SabreAuto board
--- configs/imx6qsabreauto_defconfig | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) create mode 100644 configs/imx6qsabreauto_defconfig
configs/imx6qsabreauto_defconfig new file +16 -0
@@ -0,0 +1,16 @@ +BR2_arm=y +BR2_cortex_a9=y +BR2_TOOLCHAIN_EXTERNAL=y +BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_ARM201109=y +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_UDEV=y +BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_GIT_REPO_URL="git://git.freescale.com/imx/linux-2.6-imx.git" +BR2_LINUX_KERNEL_CUSTOM_GIT_VERSION="imx_3.0.35_4.1.0" +BR2_LINUX_KERNEL_DEFCONFIG="imx6" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="mx6qsabreauto" +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_GIT_REPO_URL="git://git.denx.de/u-boot-imx.git" +BR2_TARGET_UBOOT_CUSTOM_GIT_VERSION="77b0e2239a13fa83a745ea9b03994bf780a9738a"
Signature · 1 line
1.7.9.5
PATCH 1/2 Initial support for I.MX6 SabreAuto board
Hi Abdul,
Thank you for your contribution. Even on this very small defconfig I
have a few comments :-)
Quoted 12 lines · Abdul Hussain
Signed-off-by Abdul Hussain <[email protected]>--- configs/imx6qsabreauto_defconfig | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)create mode 100644 configs/imx6qsabreauto_defconfig
configs/imx6qsabreauto_defconfig new file +0
-0
configs/imx6qsabreauto_defconfig line 4
Quoted 4 lines
configs/imx6qsabreauto_defconfig new file +4
-0@@ -0,0 +1,16 @@ +BR2_arm=y +BR2_cortex_a9=y +BR2_TOOLCHAIN_EXTERNAL=y +BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_ARM201109=y
We prefer to use the internal toolchain for minimal defconfigs.
I do realize that that means you won't be able to use this defconfig as
a basis for adding the codec and GPU libraries. As a solution, we have decided to also accept 'demo' defconfigs in the future that create a more extensive configuration that shows more of a board's capabilities.
configs/imx6qsabreauto_defconfig line 5
Quoted 1 line
configs/imx6qsabreauto_defconfig new file +1
-0+BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_UDEV=y
Why udev and not the default devtmpfs? udev adds a lot of bloat...
configs/imx6qsabreauto_defconfig line 6
Quoted 1 line
configs/imx6qsabreauto_defconfig new file +1
-0+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3"
Minor nit: the /dev/ttymxc count patch should come first in the series.
configs/imx6qsabreauto_defconfig line 10
Quoted 4 lines
configs/imx6qsabreauto_defconfig new file +4
-0+BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_GIT_REPO_URL="git://git.freescale.com/imx/linux-2.6-imx.git" +BR2_LINUX_KERNEL_CUSTOM_GIT_VERSION="imx_3.0.35_4.1.0"
Better to download a tarball from
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/snapshot/imx_3.0.35_4.1.0.tar.bz2
That goes about 10 times faster.
configs/imx6qsabreauto_defconfig line 16
Quoted 6 lines
configs/imx6qsabreauto_defconfig new file +6
-0+BR2_LINUX_KERNEL_DEFCONFIG="imx6" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="mx6qsabreauto" +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_GIT_REPO_URL="git://git.denx.de/u-boot-imx.git" +BR2_TARGET_UBOOT_CUSTOM_GIT_VERSION="77b0e2239a13fa83a745ea9b03994bf780a9738a"
Why a custom git? AFAICS there are no relevant differences between this
version and the released uboot-2013.10?
Regards,
Arnout
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286500 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F