Skip to contentSkip to conversation

dhcpcd: add option to override dbdir

PATCH New Luca Ceresoli 2 participants 5 messages Sep 30, 2013 – Nov 11, 2013

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dhcpcd: add option to override dbdir

---
 package/dhcpcd/Config.in | 14 ++++++++++++++
 package/dhcpcd/dhcpcd.mk |  1 +
 2 files changed, 15 insertions(+)
package/dhcpcd/Config.in +14 -0
index a06a973..c144dd3 100644
@@ -6,5 +6,19 @@ config BR2_PACKAGE_DHCPCD
 
 	  http://roy.marples.name/downloads/dhcpcd
 
+if BR2_PACKAGE_DHCPCD
+
+config BR2_PACKAGE_DHCPCD_DBDIR
+	string "database directory"
+	default "/var/db"
+	help
+	  By default dhcpcd stores obtained DHCP leases and other info in
+	  /var/db. Set this to any other directory you wish to use. This must
+	  be on a read-write filesystem, otherwise dhcpcd will not work.
+	  For example, you may want to change this directory if /var is on a
+	  read-only filesystem in your embedded system.
+
+endif
+
 comment "dhcpcd requires a toolchain with IPV6 support"
 	depends on !BR2_INET_IPV6
package/dhcpcd/dhcpcd.mk +1 -0
index 5296db8..4d0e86c 100644
@@ -18,6 +18,7 @@ define DHCPCD_CONFIGURE_CMDS
 	./configure \
 		--target=$(BR2_GCC_TARGET_ARCH) \
 		--os=linux \
+		--dbdir=$(BR2_PACKAGE_DHCPCD_DBDIR) \
 		$(DHCPCD_CONFIG_OPT) )
 endef
 
Signature · 1 line
1.8.1.2
#1 lore raw

PATCH 1/1 dhcpcd: add option to override dbdir

Quoted 17 lines · Luca Ceresoli
---
  package/dhcpcd/Config.in | 14 ++++++++++++++
  package/dhcpcd/dhcpcd.mk |  1 +
  2 files changed, 15 insertions(+)
package/dhcpcd/Config.in +3 -0
index a06a973..c144dd3 100644
@@ -6,5 +6,19 @@ config BR2_PACKAGE_DHCPCD
 
  	  http://roy.marples.name/downloads/dhcpcd
 
+if BR2_PACKAGE_DHCPCD
+
+config BR2_PACKAGE_DHCPCD_DBDIR

package/dhcpcd/Config.in config BR2_PACKAGE_DHCPCD · line 21

Quoted 10 lines
package/dhcpcd/Config.in +10 -0
+	string "database directory"
+	default "/var/db"
+	help
+	  By default dhcpcd stores obtained DHCP leases and other info in
+	  /var/db. Set this to any other directory you wish to use. This must
+	  be on a read-write filesystem, otherwise dhcpcd will not work.
+	  For example, you may want to change this directory if /var is on a
+	  read-only filesystem in your embedded system.
+
+endif

Hi Luca,

After discussion on the buildroot developer day, we decided that this
should not be configurable. Instead it should be hard-coded to some fixed path in /run, e.g. /run/db or something else that makes sense. (Note that /run is a symlink to /var/run which is a symlink to /tmp. We should use /run, not /var/run, because that conforms to the FHS.)

Since you probably use this package, can you test this and send a patch?

Regards,
Arnout

Quoted 16 lines
package/dhcpcd/Config.in +1 -0
+
  comment "dhcpcd requires a toolchain with IPV6 support"
  	depends on !BR2_INET_IPV6
package/dhcpcd/dhcpcd.mk +1 -0
index 5296db8..4d0e86c 100644
@@ -18,6 +18,7 @@ define DHCPCD_CONFIGURE_CMDS
  	./configure \
  		--target=$(BR2_GCC_TARGET_ARCH) \
  		--os=linux \
+		--dbdir=$(BR2_PACKAGE_DHCPCD_DBDIR) \
  		$(DHCPCD_CONFIG_OPT) )
  endef
 
Signature · 6 lines
Arnout Vandecappelle                          arnout at mind be
Senior Embedded Software Architect            +32-16-286500
Essensium/Mind                                http://www.mind.be
G.Geenslaan 9, 3001 Leuven, Belgium           BE 872 984 063 RPR Leuven
LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle
GPG fingerprint:  7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
#2 lore raw

PATCH 1/1 dhcpcd: add option to override dbdir

Arnout, All,

Quoted 32 lines · Arnout Vandecappelle
Quoted 23 lines · Luca Ceresoli
---
  package/dhcpcd/Config.in | 14 ++++++++++++++
  package/dhcpcd/dhcpcd.mk |  1 +
  2 files changed, 15 insertions(+)
package/dhcpcd/Config.in +8 -0
index a06a973..c144dd3 100644
@@ -6,5 +6,19 @@ config BR2_PACKAGE_DHCPCD
 
        http://roy.marples.name/downloads/dhcpcd
 
+if BR2_PACKAGE_DHCPCD
+
+config BR2_PACKAGE_DHCPCD_DBDIR
+    string "database directory"
+    default "/var/db"
+    help
+      By default dhcpcd stores obtained DHCP leases and other info in
+      /var/db. Set this to any other directory you wish to use. This

must

package/dhcpcd/Config.in config BR2_PACKAGE_DHCPCD · line 21

Quoted 5 lines
package/dhcpcd/Config.in +5 -0
+      be on a read-write filesystem, otherwise dhcpcd will not work.
+      For example, you may want to change this directory if /var is on a
+      read-only filesystem in your embedded system.
+
+endif

Hi Luca,

Quoted 7 lines

After discussion on the buildroot developer day, we decided that this
should not be configurable. Instead it should be hard-coded to some fixed path in /run, e.g. /run/db or something else that makes sense. (Note that /run is a symlink to /var/run which is a symlink to /tmp. We should use /run, not /var/run, because that conforms to the FHS.)

Since you probably use this package, can you test this and send a patch?

While this would likely fix the problem, this is not the correct way to do so, and would introduce another problem.

According the FHS version 3.0-draft1 /run is a volatile storage, cleared upon reboot. It may then be a tmpfs as well.

However, one of the purposes for dhcpcd to store an IP lease obtained from a DHCP server is to request the same address at the next reboot. So it is meant to be persistent, and /var is the correct place for the lease files, not /run. In fact dhcpcd by default uses /var/db, which is ok.

In other words, things are fine in current BR without any patch, provided that the rootfs is writable.

If the rootfs is read-only (which is not uncommon on small embedded systems), dhcpcd fails trying to create the "db" dir under /var. This is because in the default Buildroot skeleton /var is a regular directory, not a tmpfs.

In a system whose rootfs is read-only there is no directory in the default skeleton that is both persistent and writable.

In this case I devise two possible solutions:
* create /var/db in system/skeleton as yet another symlink to /tmp;
* let any user select the directory they wish (what my patch does).

In the first case we don't need a new config option and dhcpcd will generally work. But leases won't be persistent and the cause may be not so obvious to the user.

In the second case anyone can point to some device-specific persistent storage, thus making dhcpcd work 100% as expected.

It may be a small read-write partition for storing user-configurable data, as is already available on some embedded products. But there is no way for Buildroot to know where that is going to be mounted, so we let the user tell us via the config option.

As a side-effect, the presence of a config knob makes the user aware of the problem with a suitable help text.

Actually the former change may be applied anyway as it partially fixes dhcpcd and is minimally invasive. For the latter one I look forward to hear your comments.

Signature · 1 line
Luca
#3 lore raw

PATCH 1/1 dhcpcd: add option to override dbdir

Hi Luca,

[@Peter: there's a request for a judgement call below]

Quoted 46 lines · Luca Ceresoli

Arnout, All,

Quoted 32 lines · Arnout Vandecappelle
Quoted 23 lines · Luca Ceresoli
---
  package/dhcpcd/Config.in | 14 ++++++++++++++
  package/dhcpcd/dhcpcd.mk |  1 +
  2 files changed, 15 insertions(+)
package/dhcpcd/Config.in +8 -0
index a06a973..c144dd3 100644
@@ -6,5 +6,19 @@ config BR2_PACKAGE_DHCPCD
 
        http://roy.marples.name/downloads/dhcpcd
 
+if BR2_PACKAGE_DHCPCD
+
+config BR2_PACKAGE_DHCPCD_DBDIR
+    string "database directory"
+    default "/var/db"
+    help
+      By default dhcpcd stores obtained DHCP leases and other info in
+      /var/db. Set this to any other directory you wish to use. This

must

package/dhcpcd/Config.in config BR2_PACKAGE_DHCPCD · line 21

Quoted 5 lines
package/dhcpcd/Config.in +5 -0
+      be on a read-write filesystem, otherwise dhcpcd will not work.
+      For example, you may want to change this directory if /var is on a
+      read-only filesystem in your embedded system.
+
+endif

Hi Luca,

Quoted 7 lines

After discussion on the buildroot developer day, we decided that this
should not be configurable. Instead it should be hard-coded to some fixed path in /run, e.g. /run/db or something else that makes sense. (Note that /run is a symlink to /var/run which is a symlink to /tmp. We should use /run, not /var/run, because that conforms to the FHS.)

Since you probably use this package, can you test this and send a patch?

While this would likely fix the problem, this is not the correct way to do so, and would introduce another problem.

Quoted 7 lines

According the FHS version 3.0-draft1 /run is a volatile storage, cleared upon reboot. It may then be a tmpfs as well.

However, one of the purposes for dhcpcd to store an IP lease obtained from a DHCP server is to request the same address at the next reboot. So it is meant to be persistent, and /var is the correct place for the lease files, not /run. In fact dhcpcd by default uses /var/db, which is ok.

OK, we didn't realize that.

Quoted 11 lines

In other words, things are fine in current BR without any patch, provided that the rootfs is writable.

If the rootfs is read-only (which is not uncommon on small embedded systems), dhcpcd fails trying to create the "db" dir under /var. This is because in the default Buildroot skeleton /var is a regular directory, not a tmpfs.

In a system whose rootfs is read-only there is no directory in the default skeleton that is both persistent and writable.

Of course not, because that may not be possible.

Quoted 8 lines

In this case I devise two possible solutions:
* create /var/db in system/skeleton as yet another symlink to /tmp;
* let any user select the directory they wish (what my patch does).

In the first case we don't need a new config option and dhcpcd will generally work. But leases won't be persistent and the cause may be not so obvious to the user.

But we can add to the dhcpd help text that you need to replace the
/var/db symlink to point to a persistent location if you want persistence.

But then again, adding the configure option does have the same effect,
just a little more obvious to the user.

At the Buildroot developer meeting, we also asked Peter to play a bit
more the role of the benevolent dictator and make rulings. So here goes:

Peter, do you prefer a /var/db symlink that the user should override in
the fs overlay, or do you prefer an explicit configure option?

If we do go for the configure option, however, the default should be
/tmp or /tmp/db, so that at least the default works with a read-only rootfs.

Quoted 8 lines

In the second case anyone can point to some device-specific persistent storage, thus making dhcpcd work 100% as expected.

It may be a small read-write partition for storing user-configurable data, as is already available on some embedded products. But there is no way for Buildroot to know where that is going to be mounted, so we let the user tell us via the config option.

Quoted 6 lines

As a side-effect, the presence of a config knob makes the user aware of the problem with a suitable help text.

Actually the former change may be applied anyway as it partially fixes dhcpcd and is minimally invasive. For the latter one I look forward to hear your comments.

Yes, if it is not configurable, then buildroot should create the
symlink. However, I wouldn't put it in the skeleton, but instead put it in the INSTALL_TARGET_CMDS.

Regards,
Arnout

Signature · 6 lines
Arnout Vandecappelle                          arnout at mind be
Senior Embedded Software Architect            +32-16-286500
Essensium/Mind                                http://www.mind.be
G.Geenslaan 9, 3001 Leuven, Belgium           BE 872 984 063 RPR Leuven
LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle
GPG fingerprint:  7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
#4 lore raw

PATCH 1/1 dhcpcd: add option to override dbdir

Peter,

do you have a judgement about which is the best way to fix this issue?

I hope we can have this sorted out in time for 2013.11.

Quoted 127 lines · Arnout Vandecappelle

Hi Luca,

[@Peter: there's a request for a judgement call below]

Quoted 48 lines · Luca Ceresoli

Arnout, All,

Quoted 33 lines · Arnout Vandecappelle
Quoted 26 lines · Luca Ceresoli
---
  package/dhcpcd/Config.in | 14 ++++++++++++++
  package/dhcpcd/dhcpcd.mk |  1 +
  2 files changed, 15 insertions(+)
package/dhcpcd/Config.in +8 -0
index a06a973..c144dd3 100644
@@ -6,5 +6,19 @@ config BR2_PACKAGE_DHCPCD
 
        http://roy.marples.name/downloads/dhcpcd
 
+if BR2_PACKAGE_DHCPCD
+
+config BR2_PACKAGE_DHCPCD_DBDIR
+    string "database directory"
+    default "/var/db"
+    help
+      By default dhcpcd stores obtained DHCP leases and other info in
+      /var/db. Set this to any other directory you wish to use. This

must

package/dhcpcd/Config.in +2 -0
+      be on a read-write filesystem, otherwise dhcpcd will not work.
+      For example, you may want to change this directory if /var is

on a

package/dhcpcd/Config.in config BR2_PACKAGE_DHCPCD · line 21

Quoted 3 lines
package/dhcpcd/Config.in +3 -0
+      read-only filesystem in your embedded system.
+
+endif

Hi Luca,

Quoted 8 lines

After discussion on the buildroot developer day, we decided that this
should not be configurable. Instead it should be hard-coded to some fixed path in /run, e.g. /run/db or something else that makes sense. (Note that /run is a symlink to /var/run which is a symlink to /tmp. We should use /run, not /var/run, because that conforms to the FHS.)

Since you probably use this package, can you test this and send a
patch?

While this would likely fix the problem, this is not the correct way to do so, and would introduce another problem.

Quoted 7 lines

According the FHS version 3.0-draft1 /run is a volatile storage, cleared upon reboot. It may then be a tmpfs as well.

However, one of the purposes for dhcpcd to store an IP lease obtained from a DHCP server is to request the same address at the next reboot. So it is meant to be persistent, and /var is the correct place for the lease files, not /run. In fact dhcpcd by default uses /var/db, which is ok.

OK, we didn't realize that.

Quoted 11 lines

In other words, things are fine in current BR without any patch, provided that the rootfs is writable.

If the rootfs is read-only (which is not uncommon on small embedded systems), dhcpcd fails trying to create the "db" dir under /var. This is because in the default Buildroot skeleton /var is a regular directory, not a tmpfs.

In a system whose rootfs is read-only there is no directory in the default skeleton that is both persistent and writable.

Of course not, because that may not be possible.

Quoted 8 lines

In this case I devise two possible solutions:
* create /var/db in system/skeleton as yet another symlink to /tmp;
* let any user select the directory they wish (what my patch does).

In the first case we don't need a new config option and dhcpcd will generally work. But leases won't be persistent and the cause may be not so obvious to the user.

But we can add to the dhcpd help text that you need to replace the
/var/db symlink to point to a persistent location if you want persistence.

But then again, adding the configure option does have the same effect,
just a little more obvious to the user.

At the Buildroot developer meeting, we also asked Peter to play a bit
more the role of the benevolent dictator and make rulings. So here goes:

Peter, do you prefer a /var/db symlink that the user should override
in the fs overlay, or do you prefer an explicit configure option?

If we do go for the configure option, however, the default should be
/tmp or /tmp/db, so that at least the default works with a read-only rootfs.

Quoted 8 lines

In the second case anyone can point to some device-specific persistent storage, thus making dhcpcd work 100% as expected.

It may be a small read-write partition for storing user-configurable data, as is already available on some embedded products. But there is no way for Buildroot to know where that is going to be mounted, so we let the user tell us via the config option.

Quoted 6 lines

As a side-effect, the presence of a config knob makes the user aware of the problem with a suitable help text.

Actually the former change may be applied anyway as it partially fixes dhcpcd and is minimally invasive. For the latter one I look forward to hear your comments.

Yes, if it is not configurable, then buildroot should create the
symlink. However, I wouldn't put it in the skeleton, but instead put it in the INSTALL_TARGET_CMDS.

Regards,
Arnout

Signature · 1 line
Luca