drm/i915: Fix subslice configuration on Gen9LP
Subsystems (2)
Tvrtko Ursulin
maintainerPATCH 1/1 drm/i915: Fix subslice configuration on Gen9LP
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice = 0x001
2 slices = 0x010
3 slices = 0x100
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming 0x11 into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?
Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..
How to test in what configuration do these parts run before and after this patch?
--- drivers/gpu/drm/i915/intel_lrc.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_lrc.c +8 -2
@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) }if (INTEL_INFO (dev_priv)->sseu.has_subslice_pg) { +u8 val; + + val =hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]); + +if (IS_GEN9_LP (dev_priv)) + val =BIT (val -1 ); + rpcs |=GEN8_RPCS_SS_CNT_ENABLE ; - rpcs |=hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]) << -GEN8_RPCS_SS_CNT_SHIFT ; + rpcs |= val <<GEN8_RPCS_SS_CNT_SHIFT ; rpcs |=GEN8_RPCS_ENABLE ; }
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Tvrtko Ursulin
maintainerQuoted 12 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice = 0x001 2 slices = 0x010 3 slices = 0x100And not the popcount of the enabled subslice mask as on other platforms.
Quoted 8 lines
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
If it does turn out to be broken and this the correct fix then:
?
At that time code looked like:
+ if (INTEL_INFO(dev)->has_subslice_pg) {
+ rpcs |= GEN8_RPCS_SS_CNT_ENABLE; + rpcs |= INTEL_INFO(dev)->subslice_per_slice <<
+ GEN8_RPCS_SS_CNT_SHIFT;
+ rpcs |= GEN8_RPCS_ENABLE;
+ }
So would had already most likely been broken.
Tvrtko
Quoted 23 lines
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
--- drivers/gpu/drm/i915/intel_lrc.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +4
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) }if (INTEL_INFO (dev_priv)->sseu.has_subslice_pg) { +u8 val; + + val =hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]); +
drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2522
Quoted 10 lines
drivers/gpu/drm/i915/intel_lrc.c +4
-2+if (IS_GEN9_LP (dev_priv)) + val =BIT (val -1 ); + rpcs |=GEN8_RPCS_SS_CNT_ENABLE ; - rpcs |=hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]) << -GEN8_RPCS_SS_CNT_SHIFT ; + rpcs |= val <<GEN8_RPCS_SS_CNT_SHIFT ; rpcs |=GEN8_RPCS_ENABLE ; }
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for drm/i915: Fix subslice configuration on Gen9LP
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: drm/i915: Fix subslice configuration on Gen9LP
URL : https://patchwork.freedesktop.org/series/48566/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4696 -> Patchwork_9991 =
== Summary - SUCCESS ==
No regressions found.
External URL: https://patchwork.freedesktop.org/api/1.0/series/48566/revisions/1/mbox/
== Possible new issues ==
Here are the unknown changes that may have been introduced in Patchwork_9991:
=== IGT changes ===
==== Warnings ====
{igt@kms_psr@primary_page_flip}:
fi-cnl-psr: DMESG-FAIL -> DMESG-WARN== Known issues ==
Here are the changes found in Patchwork_9991 that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@drv_selftest@live_hangcheck:
fi-skl-guc: PASS -> DMESG-FAIL (fdo#107174)
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-b:
fi-snb-2520m: PASS -> INCOMPLETE (fdo#103713)
fi-cnl-psr: PASS -> DMESG-WARN (fdo#104951)
==== Possible fixes ====
igt@drv_selftest@live_hangcheck:
{fi-skl-iommu}: DMESG-FAIL (fdo#107174, fdo#106560) -> PASS
fi-kbl-7567u: DMESG-FAIL (fdo#106947, fdo#106560) -> PASS
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
{fi-byt-clapper}: FAIL (fdo#107362, fdo#103191) -> PASS
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-b:
{fi-cfl-8109u}: INCOMPLETE (fdo#106070) -> PASS
==== Warnings ====
{igt@pm_rpm@module-reload}:
fi-cnl-psr: FAIL -> WARN (fdo#107602) {name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#103713 https://bugs.freedesktop.org/show_bug.cgi?id=103713
fdo#104951 https://bugs.freedesktop.org/show_bug.cgi?id=104951
fdo#106070 https://bugs.freedesktop.org/show_bug.cgi?id=106070
fdo#106560 https://bugs.freedesktop.org/show_bug.cgi?id=106560
fdo#106947 https://bugs.freedesktop.org/show_bug.cgi?id=106947
fdo#107174 https://bugs.freedesktop.org/show_bug.cgi?id=107174
fdo#107362 https://bugs.freedesktop.org/show_bug.cgi?id=107362
fdo#107602 https://bugs.freedesktop.org/show_bug.cgi?id=107602
== Participating hosts (54 -> 48) ==
Missing (6): fi-ilk-m540 fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-ctg-p8600 fi-glk-j4005
== Build changes ==
* Linux: CI_DRM_4696 -> Patchwork_9991
CI_DRM_4696: ced152c46fc90f7c1ac8963850d64c9f1ce652d6 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4608: 94ebd21177feedf03e8f6dd1e73dca1a6ec7a0ac @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_9991: 75e3f1910f813b2dff2ae2794d9e84e9f832188c @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
75e3f1910f81 drm/i915: Fix subslice configuration on Gen9LP
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_9991/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice = 0x001 2 slices = 0x010 3 slices = 0x100
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
--- drivers/gpu/drm/i915/intel_lrc.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0
drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2516
Quoted 9 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) }if (INTEL_INFO (dev_priv)->sseu.has_subslice_pg) { +u8 val; + + val =hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]); + +if (IS_GEN9_LP (dev_priv)) + val =BIT (val -1 );
Hmm... Are you breaking the 2 subslices setting here then?
(2 subslices = 0b10 which should be equal to hweight8(subslice_mask) if I'm thinking right)
drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2522
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +2
-2+ rpcs |=GEN8_RPCS_SS_CNT_ENABLE ; - rpcs |=hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]) << -GEN8_RPCS_SS_CNT_SHIFT ; + rpcs |= val <<GEN8_RPCS_SS_CNT_SHIFT ; rpcs |=GEN8_RPCS_ENABLE ; }
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100
Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 38 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2515
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val = hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)
No and yes, I think.
subslice_mask = 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the register
In the same way, all together:
subslice_mask = 0b001 => hweight = 1 => BIT(0) = 0b001 subslice_mask = 0b011 => hweight = 2 => BIT(1) = 0b010 subslice_mask = 0b111 => hweight = 3 => BIT(2) = 0b100
Have I made a mistake somewhere?
Regards,
Tvrtko
Quoted 10 lines
drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2521
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +2
-2+ rpcs |= GEN8_RPCS_SS_CNT_ENABLE; - rpcs |= hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]) << - GEN8_RPCS_SS_CNT_SHIFT; + rpcs |= val << GEN8_RPCS_SS_CNT_SHIFT; rpcs |= GEN8_RPCS_ENABLE; }
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Lionel Landwerlin
Reviewed-byQuoted 65 lines · Tvrtko Ursulin
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 38 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2515
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val = hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)No and yes, I think.
subslice_mask= 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the register
Quoted 7 lines
In the same way, all together:
subslice_mask= 0b001 => hweight = 1 => BIT(0) = 0b001subslice_mask= 0b011 => hweight = 2 => BIT(1) = 0b010subslice_mask= 0b111 => hweight = 3 => BIT(2) = 0b100Have I made a mistake somewhere?
Ah, yes! You're right :)
My eyes got tricked, thanks for finding this out.
With the comment fixed :
Quoted 21 lines
Regards,
Tvrtko
Quoted 15 lines
Quoted 9 lines
drivers/gpu/drm/i915/intel_lrc.c +1
-1+ rpcs |= GEN8_RPCS_SS_CNT_ENABLE; - rpcs |=hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]) << -
GEN8_RPCS_SS_CNT_SHIFT;
+ rpcs |= val <<GEN8_RPCS_SS_CNT_SHIFT; rpcs |=GEN8_RPCS_ENABLE;
}_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 72 lines · Lionel Landwerlin
Quoted 71 lines · Tvrtko Ursulin
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 38 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2515
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val = hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)No and yes, I think.
subslice_mask= 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the registerIn the same way, all together:
subslice_mask= 0b001 => hweight = 1 => BIT(0) = 0b001subslice_mask= 0b011 => hweight = 2 => BIT(1) = 0b010subslice_mask= 0b111 => hweight = 3 => BIT(2) = 0b100
Quoted 6 lines
Quoted 1 line
Have I made a mistake somewhere?
Ah, yes! You're right :)
My eyes got tricked, thanks for finding this out.
At least half of the credit goes to you for linking to 12247 in scope of one different thread!
Quoted 5 lines
With the comment fixed :
Reviewed-by Lionel Landwerlin <[email protected]>
Thanks!
Any ideas on how to test this? I'd like to commit message to be more precise - have we been running with one slice too few? Or hardware ignores the undocumented bit combination? Or even, is the documentation perhaps incorrect?!
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 84 lines · Tvrtko Ursulin
Quoted 72 lines · Lionel Landwerlin
Quoted 71 lines · Tvrtko Ursulin
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 38 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2515
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val = hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)No and yes, I think.
subslice_mask= 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the registerIn the same way, all together:
subslice_mask= 0b001 => hweight = 1 => BIT(0) = 0b001subslice_mask= 0b011 => hweight = 2 => BIT(1) = 0b010subslice_mask= 0b111 => hweight = 3 => BIT(2) = 0b100Quoted 6 lines
Quoted 1 line
Have I made a mistake somewhere?
Ah, yes! You're right :)
My eyes got tricked, thanks for finding this out.
At least half of the credit goes to you for linking to 12247 in scope of one different thread!
Quoted 1 line
Quoted 8 lines
Quoted 4 lines
With the comment fixed :
Reviewed-by Lionel Landwerlin <[email protected]>Thanks!
Any ideas on how to test this? I'd like to commit message to be more precise - have we been running with one slice too few? Or hardware ignores the undocumented bit combination? Or even, is the documentation perhaps incorrect?!
Yeah the tests that I wrote to test the API you're picking up use a MI_PREDICATE where you can make a command (let's say MI_STORE_REGISTER_MEM) conditional on the number of slice.
You can use that in a user batch an verify that memory has or hasn't been written to.
That's only before Gen10 though.
I'm looking at whether something that is passed onto the EUs could map back to the physical location.
Not sure if there is something...
-
Lionel
Quoted 5 lines
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 97 lines · Lionel Landwerlin
Quoted 84 lines · Tvrtko Ursulin
Quoted 72 lines · Lionel Landwerlin
Quoted 71 lines · Tvrtko Ursulin
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 38 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2515
Quoted 8 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val = hweight8(INTEL_INFO(dev_priv)->sseu.subslice_mask[0]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)No and yes, I think.
subslice_mask= 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the registerIn the same way, all together:
subslice_mask= 0b001 => hweight = 1 => BIT(0) = 0b001subslice_mask= 0b011 => hweight = 2 => BIT(1) = 0b010subslice_mask= 0b111 => hweight = 3 => BIT(2) = 0b100Quoted 6 lines
Quoted 1 line
Have I made a mistake somewhere?
Ah, yes! You're right :)
My eyes got tricked, thanks for finding this out.
At least half of the credit goes to you for linking to 12247 in scope of one different thread!
Quoted 1 line
Quoted 8 lines
Quoted 4 lines
With the comment fixed :
Reviewed-by Lionel Landwerlin <[email protected]>Thanks!
Any ideas on how to test this? I'd like to commit message to be more precise - have we been running with one slice too few? Or hardware ignores the undocumented bit combination? Or even, is the documentation perhaps incorrect?!
Yeah the tests that I wrote to test the API you're picking up use a
MI_PREDICATEwhere you can make a command (let's sayMI_STORE_REGISTER_MEM) conditional on the number of slice.
Quoted 8 lines
You can use that in a user batch an verify that memory has or hasn't been written to.
That's only before Gen10 though.
I'm looking at whether something that is passed onto the EUs could map back to the physical location.
Not sure if there is something...
I've sent an exploratory IGT based on your MI_SET_PREDICATE code to CI. Although that only works on the basis of slices, and here doubt is about subslices. But at least it should log subslice configuration so we'll see if the incorrect programming survived in the register, or on read-back we get a different value.
Otherwise I was thinking if in some Mesa test farm you have an appropriate BXT/GLK and could notice a performance difference before and after this patch?
But again, sounds so unbelievable we would be running with one disabled slice all this time..
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 106 lines · Tvrtko Ursulin
Quoted 105 lines · Lionel Landwerlin
Quoted 85 lines · Tvrtko Ursulin
Quoted 73 lines · Lionel Landwerlin
Quoted 72 lines · Tvrtko Ursulin
Quoted 12 lines · Lionel Landwerlin
Quoted 9 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
According to the documentation, when programming the subslice count power- gating configuration register, the value to be written into it on Gen9LP should actually in the format of:
1 slice =
0x001
2 slices =0x010
3 slices =0x100Quoted 4 lines
s/slice/subslice/
Also 0b001 etc... Not hexadecimal.
Oops, you're right.
Quoted 39 lines
Quoted 26 lines
And not the popcount of the enabled subslice mask as on other platforms.
So on Gen9LP platforms we have been programming
0x11into those bits, but the documentation does not explain what would that achieve. Could it be that we enable only two subslice on three sub-slice parts? Or hardware simply ignores it and sticks with the maximum configuration?Signed-off-by Tvrtko Ursulin <[email protected]>Cc Lionel Landwerlin <[email protected]>Bspec: 12247
---
Could this actually be true or I am severely misreading the docs? It does not sound plausible to me this would have been missed all this time..How to test in what configuration do these parts run before and after this patch?
---
drivers/gpu/drm/i915/intel_lrc.c| 10 ++++++++--1 file changed, 8 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_lrc.c +0
-0drivers/gpu/drm/i915/intel_lrc.c make_rpcs(struct drm_i915_private *dev_priv) · line 2516
Quoted 9 lines
drivers/gpu/drm/i915/intel_lrc.c +6
-0@@ -2508,9 +2508,15 @@ make_rpcs(struct drm_i915_private *dev_priv) } if (INTEL_INFO(dev_priv)->sseu.has_subslice_pg) { + u8 val; + + val =hweight8 (INTEL_INFO (dev_priv)->sseu.subslice_mask[0 ]); + + if (IS_GEN9_LP(dev_priv)) + val = BIT(val - 1);Hmm... Are you breaking the 2 subslices setting here then?
Quoted 1 line
(2 subslices = 0b10 which should be equal to
hweight8(subslice_mask)if I'm thinking right)No and yes, I think.
subslice_mask= 0b011 => hweight = 2 => BIT(2 - 1) = BIT(1) = 0b010 into the registerIn the same way, all together:
subslice_mask= 0b001 => hweight = 1 => BIT(0) = 0b001subslice_mask= 0b011 => hweight = 2 => BIT(1) = 0b010subslice_mask= 0b111 => hweight = 3 => BIT(2) = 0b100Quoted 6 lines
Quoted 1 line
Have I made a mistake somewhere?
Ah, yes! You're right :)
My eyes got tricked, thanks for finding this out.
At least half of the credit goes to you for linking to 12247 in scope of one different thread!
Quoted 1 line
Quoted 8 lines
Quoted 4 lines
With the comment fixed :
Reviewed-by Lionel Landwerlin <[email protected]>Thanks!
Any ideas on how to test this? I'd like to commit message to be more precise - have we been running with one slice too few? Or hardware ignores the undocumented bit combination? Or even, is the documentation perhaps incorrect?!
Yeah the tests that I wrote to test the API you're picking up use a
MI_PREDICATEwhere you can make a command (let's sayMI_STORE_REGISTER_MEM) conditional on the number of slice.You can use that in a user batch an verify that memory has or hasn't been written to.
That's only before Gen10 though.
I'm looking at whether something that is passed onto the EUs could map back to the physical location.
Quoted 7 lines
Quoted 1 line
Not sure if there is something...
I've sent an exploratory IGT based on your
MI_SET_PREDICATEcode to CI. Although that only works on the basis of slices, and here doubt is about subslices. But at least it should log subslice configuration so we'll see if the incorrect programming survived in the register, or on read-back we get a different value.Otherwise I was thinking if in some Mesa test farm you have an appropriate BXT/GLK and could notice a performance difference before and after this patch?
But again, sounds so unbelievable we would be running with one disabled slice all this time..
Results are finally back (https://intel-gfx-ci.01.org/tree/drm-tip/Trybot_2831/fi-glk-dsi/igt@drv_selftest@live_contexts.html - starts at timestamp 457.627031 in dmesg) and empirically it seems that BXT/GLK handles the SScount identically to big core SKUs.
In other words there is no switching penalty between SScount 0b11 and 0b100, whilst there is between different configs, implying that undocumented 0b11 correctly selected three subslices, equally as the documented 0b100.
Small concern is that switching performance between 0b100<->0b10 and 0b11<->0b10 seems potentially greater than the margin of error which I can't explain other than maybe my test being imperfect, or noise is greater than I think.
I will raise a note against bspec to see if we can clarify that via that route.
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.IGT: success for drm/i915: Fix subslice configuration on Gen9LP
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: drm/i915: Fix subslice configuration on Gen9LP
URL : https://patchwork.freedesktop.org/series/48566/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4696_full -> Patchwork_9991_full =
== Summary - WARNING ==
Minor unknown changes coming with Patchwork_9991_full need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_9991_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
== Possible new issues ==
Here are the unknown changes that may have been introduced in Patchwork_9991_full:
=== IGT changes ===
==== Warnings ====
igt@kms_cursor_legacy@cursorb-vs-flipa-toggle:
shard-hsw: SKIP -> PASS== Known issues ==
Here are the changes found in Patchwork_9991_full that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@gem_ctx_isolation@vcs1-s3:
shard-kbl: PASS -> INCOMPLETE (fdo#103665)
igt@gem_exec_await@wide-contexts:
shard-glk: PASS -> FAIL (fdo#105900)
shard-kbl: PASS -> FAIL (fdo#105900)
igt@kms_available_modes_crc@available_mode_test_crc:
shard-kbl: NOTRUN -> FAIL (fdo#106641)
==== Possible fixes ====
igt@drv_suspend@shrink:
shard-glk: FAIL (fdo#106886) -> PASS
igt@gem_ppgtt@blt-vs-render-ctxn:
shard-kbl: INCOMPLETE (fdo#106023, fdo#103665) -> PASS +1
igt@kms_flip@2x-flip-vs-expired-vblank-interruptible:
shard-glk: FAIL (fdo#105363) -> PASS +1
igt@kms_flip@flip-vs-expired-vblank-interruptible:
shard-glk: FAIL (fdo#102887, fdo#105363) -> PASS
igt@perf@polling:
shard-hsw: FAIL (fdo#102252) -> PASS fdo#102252 https://bugs.freedesktop.org/show_bug.cgi?id=102252
fdo#102887 https://bugs.freedesktop.org/show_bug.cgi?id=102887
fdo#103665 https://bugs.freedesktop.org/show_bug.cgi?id=103665
fdo#105363 https://bugs.freedesktop.org/show_bug.cgi?id=105363
fdo#105900 https://bugs.freedesktop.org/show_bug.cgi?id=105900
fdo#106023 https://bugs.freedesktop.org/show_bug.cgi?id=106023
fdo#106641 https://bugs.freedesktop.org/show_bug.cgi?id=106641
fdo#106886 https://bugs.freedesktop.org/show_bug.cgi?id=106886
== Participating hosts (5 -> 5) ==
No changes in participating hosts
== Build changes ==
* Linux: CI_DRM_4696 -> Patchwork_9991
CI_DRM_4696: ced152c46fc90f7c1ac8963850d64c9f1ce652d6 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4608: 94ebd21177feedf03e8f6dd1e73dca1a6ec7a0ac @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_9991: 75e3f1910f813b2dff2ae2794d9e84e9f832188c @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_9991/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx