Wrong command sequence to access eMMC RPMB area in mmc initialisation code?
Hi,
During the mmc initialisation, all the non zero sized partitions (read from
ext_csd register) are added in card structures. Then at the time of mmc
block driver probing, mmc_blk_alloc_part function is called for each
partition which initialises the mmc request queue and and starts mmc queue
thread for each partition as shown below
root@mx6q35:~# ps x | grep mmc
46 ? S 0:00 [mmcqd/1]
397 ? S 0:00 [mmcqd/2]
400 ? S 0:00 [mmcqd/2boot0]
401 ? S 0:00 [mmcqd/2boot1]
402 ? S 0:00 [mmcqd/2rpmb]
mmc queue thread for each partition gets scheduled and calls
mmc_blk_issue_rq, and here it sends CMD6 using mmc_blk_part_switch,
CMD23-->CMD18 using mmc_blk_issue_rw_rq. When executed for RPMB partition,
logs can be seen below
[ 109.972564] mmc2: starting CMD6 arg 03b30b01 flags 0000049d --> switch to RPMB area
[ 109.972600] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.972625] mmc2: req done (CMD6): 0: 00000800 00000000 00000000 00000000
[ 109.977781] mmc2: starting CMD13 arg 00010000 flags 00000195
[ 109.977823] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.977849] mmc2: req done (CMD13): 0: 00000900 00000000 00000000 00000000
[ 109.983013] <mmc2: starting CMD23 arg 00000080 flags 00000015>
[ 109.983024] mmc2: starting CMD18 arg 00000000 flags 000000b5
[ 109.983037] mmc2: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
[ 109.983048] mmc2: CMD12 arg 00000000 flags 0000049d
[ 109.983083] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.983218] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.986505] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x0000000a
[ 109.986518] sdhci [sdhci_data_irq()]: mmc2: DMA base 0x3caf0000,
transferred 0x010000 bytes, next 0x3cb00000
[ 109.986672] mmc2: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 109.986691] mmc2: 65536 bytes transferred: 0
[ 109.986709] mmc2: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 109.992355] <mmc2: starting CMD23 arg 00000080 flags 00000015>
[ 109.992368] mmc2: starting CMD18 arg 00000080 flags 000000b5
[ 109.992381] mmc2: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
[ 109.992392] mmc2: CMD12 arg 00000000 flags 0000049d
[ 109.992424] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.992724] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 109.996010] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x0000000a
[ 109.996025] sdhci [sdhci_data_irq()]: mmc2: DMA base 0x3cb40000,
transferred 0x040000 bytes, next 0x3cb80000
[ 109.996160] mmc2: req done (CMD18): 0: 00000900 00000000 00000000 00000000
[ 109.996169] mmc2: 65536 bytes transferred: 0
[ 109.996179] mmc2: (CMD12): 0: 00000000 00000000 00000000 00000000
[ 110.002250] mmc2: starting CMD6 arg 03b30a01 flags 0000049d --> switch to Boot Partition 2 area
[ 110.002292] sdhci [sdhci_irq()]: *** mmc2 got interrupt: 0x00000001
[ 110.002318] mmc2: req done (CMD6): 0: 00000800 00000000 00000000 00000000
This is the point where we are facing issues with Hynix eMMC devices.
link to original thread http://www.spinics.net/lists/linux-mmc/msg20461.html
A good way to reproduce the issue can be by unbinding/binding the eMMC device with
block driver as follows
root@mx6q35:~# echo mmc2:0001 > /sys/bus/mmc/drivers/mmcblk/unbind
root@mx6q35:~# echo mmc2:0001 > /sys/bus/mmc/drivers/mmcblk/bind
Now my question is since RPMB is not a regular partition and a different command
sequence(CMD6-->CMD23-->CMD25-->CMD23-->CMD18) as mentioned in JEDEC
Standard No. 84-A441, is required to access it, then why mmc initialisation
code is using the wrong command sequence(CMD6-->CMD23-->CMD18) to access it?
Thanks .
Abbas Raza