Skip to contentSkip to conversation

malta: use unmapped flash base address

PATCH New Gabor Juhos 2 participants 3 messages Nov 11, 2013 MIPS

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 malta: use unmapped flash base address

The physical base address of the NOR flash is 0x1e000000 on the Malta boards. The hardware also maps the first 4MiB of the flash into the 0x1fc00000-0x1fffffff range.

Currently, U-Boot uses the mapped address to access the flash, which does not work in recent qemu versions.

Since commit a427338b222b43197c2776cbc996936df0302f51 (mips_malta: correct reading MIPS revision at 0x1fc00010) writing to the mapped address space causes a CPU exception. Due to the exception, U-Boot hangs during boot when it tries to detect the CFI flash chip.

Use the correct physical address for the MALTA_FLASH_BASE constant to avoid the problem. The change makes it possible to start U-Boot on a Malta board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also works on older versions (tested with 1.1.1, 1.2.2, 1.4.2, 1.5.3). The change is not tested on a real Malta board.

Cc Daniel Schwierzeck <[email protected]>
Cc Paul Burton <[email protected]>
---
 arch/mips/include/asm/malta.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/mips/include/asm/malta.h +1 -1
index 9b1100b..bd9043d 100644
@@ -44,7 +44,7 @@
 #define MALTA_RESET_BASE		0x1f000500
 #define GORESET				0x42
 
-#define MALTA_FLASH_BASE		0x1fc00000
+#define MALTA_FLASH_BASE		0x1e000000
 
 #define MALTA_REVISION			0x1fc00010
 #define MALTA_REVISION_CORID_SHF	10
Signature · 1 line
1.7.10
#1 lore raw

PATCH 1/1 malta: use unmapped flash base address

Quoted 33 lines · Gabor Juhos

The physical base address of the NOR flash is 0x1e000000 on the Malta boards. The hardware also maps the first 4MiB of the flash into the 0x1fc00000-0x1fffffff range.

Currently, U-Boot uses the mapped address to access the flash, which does not work in recent qemu versions.

Since commit a427338b222b43197c2776cbc996936df0302f51 (mips_malta: correct reading MIPS revision at 0x1fc00010) writing to the mapped address space causes a CPU exception. Due to the exception, U-Boot hangs during boot when it tries to detect the CFI flash chip.

Use the correct physical address for the MALTA_FLASH_BASE constant to avoid the problem. The change makes it possible to start U-Boot on a Malta board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also works on older versions (tested with 1.1.1, 1.2.2, 1.4.2, 1.5.3). The change is not tested on a real Malta board.

Cc Daniel Schwierzeck <[email protected]>
Cc Paul Burton <[email protected]>
---
  arch/mips/include/asm/malta.h |    2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
arch/mips/include/asm/malta.h +0 -0
index 9b1100b..bd9043d 100644

arch/mips/include/asm/malta.h line 50

Quoted 8 lines
arch/mips/include/asm/malta.h +1 -1
@@ -44,7 +44,7 @@
  #define MALTA_RESET_BASE		0x1f000500
  #define GORESET				0x42
 
-#define MALTA_FLASH_BASE		0x1fc00000
+#define MALTA_FLASH_BASE		0x1e000000
 
  #define MALTA_REVISION			0x1fc00010
  #define MALTA_REVISION_CORID_SHF	10

Hmm, this does run on a real Malta but it takes around a minute to run relocate_code... With the 0x1fc00000 base address it's much faster. I'll see if I can figure out why...

Paul

#2 lore raw

PATCH 1/1 malta: use unmapped flash base address

2013.11.11. 15:22 keltez?ssel, Paul Burton ?rta:

<...>

Quoted 11 lines
Quoted 11 lines
arch/mips/include/asm/malta.h +1 -1
index 9b1100b..bd9043d 100644
@@ -44,7 +44,7 @@
  #define MALTA_RESET_BASE        0x1f000500
  #define GORESET                0x42
 
-#define MALTA_FLASH_BASE        0x1fc00000
+#define MALTA_FLASH_BASE        0x1e000000
 
Quoted 7 lines

arch/mips/include/asm/malta.h line 50

Quoted 3 lines
arch/mips/include/asm/malta.h +0 -0
  #define MALTA_REVISION            0x1fc00010
  #define MALTA_REVISION_CORID_SHF    10

Hmm, this does run on a real Malta but it takes around a minute to run relocate_code... With the 0x1fc00000 base address it's much faster. I'll see if I can figure out why...

Hm, you are right. Although I did not notice that before, but with this patch U-Boot starts slower also in qemu. It seems that the problem is in the relocation code. I'm preparing a patch to fix that.

-Gabor