Skip to contentSkip to conversation

upstream Arndale support

U-Boot Andre Przywara 2 participants 3 messages Dec 4, 2013

lore
Share & tools
lore
#0 lore raw

Hi,

I cannot get upstream u-boot to run on an Arndale board. Everything works when I use the Linaro branch. But this tree is old and carries a whole different set of patches for Arndale.
Is the Arndale upstream support supposed to work? If yes, is there a different recipe for populating the uSD card?

What works is the following:

$ git checkout linaro
$ make arndale5250_config && make -j arndale5250
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/smdk5250-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49

Transferring this to upstream I get the following:

$ git checkout master
$ make arndale_config && make -j arndale
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/arndale-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49

However while the Linaro based build works fine, I don't get any serial output on the upstream build.

Can someone give any hints?

Thanks,
Andre.

#1 lore raw

Hi Andre,

Quoted 15 lines · Andre Przywara

Hi,

I cannot get upstream u-boot to run on an Arndale board. Everything works when I use the Linaro branch. But this tree is old and carries a whole different set of patches for Arndale.
Is the Arndale upstream support supposed to work? If yes, is there a different recipe for populating the uSD card?

What works is the following:

$ git checkout linaro
$ make arndale5250_config && make -j arndale5250
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/smdk5250-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49
Quoted 6 lines

Transferring this to upstream I get the following:

$ git checkout master
$ make arndale_config && make -j arndale
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/arndale-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49

dd if=u-boot-dtb.bin of=/dev/sdb seek=49

Quoted 8 lines

However while the Linaro based build works fine, I don't get any serial output on the upstream build.

Can someone give any hints?

Thanks,
Andre.

Signature · 2 lines
with warm regards,
Chander Kashyap
#2 lore raw
Quoted 18 lines · Chander Kashyap

Hi Andre,

Quoted 15 lines · Andre Przywara

Hi,

I cannot get upstream u-boot to run on an Arndale board. Everything works when I use the Linaro branch. But this tree is old and carries a whole different set of patches for Arndale.
Is the Arndale upstream support supposed to work? If yes, is there a different recipe for populating the uSD card?

What works is the following:

$ git checkout linaro
$ make arndale5250_config && make -j arndale5250
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/smdk5250-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49
Quoted 7 lines
Quoted 6 lines

Transferring this to upstream I get the following:

$ git checkout master
$ make arndale_config && make -j arndale
$ dd if=/tmp/arndale-bl1.bin of=/dev/sdb seek=1
$ dd if=spl/arndale-spl.bin of=/dev/sdb seek=17
$ dd if=u-boot.bin of=/dev/sdb seek=49

dd if=u-boot-dtb.bin of=/dev/sdb seek=49

Indeed! That works!

Thanks a lot!

Andre.

Quoted 11 lines
Quoted 8 lines

However while the Linaro based build works fine, I don't get any serial output on the upstream build.

Can someone give any hints?

Thanks,
Andre.