need help to configure IRQ on gpio 139 pandaboard using device tree
Hi everybody,
I'm trying to configure an IRQ on pandaboard using device tree but I'm not able to understand how I can do it.
I want to configure the the gpio_139 pin and without device tree my command was:
OMAP4_MUX(MCSPI1_SIMO, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),
I need to associate it to a i2c device, declared in this way:
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins>;
clock-frequency = <400000>;
lsm303d@03 {
compatible = "st,lsm303d";
reg = <0x03>;
};
};and it works, but I don't know how I can set the interrupt using:
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* example */
Thanks,
Denis
Quoted 10 lines · Denis CIOCCA
Hi everybody,
I'm trying to configure an IRQ on pandaboard using device tree but I'm not able to understand how I can do it.
I want to configure the thegpio_139pin and without device tree my command was:
OMAP4_MUX(MCSPI1_SIMO, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),I need to associate it to a i2c device, declared in this way:
here is how you'd figure it out in dt world ;) - it might be a little simpler or harder depending on which end of the development world one is from... (gmail might be screwing up my formatting a little.. so apologies before hand.
http://pastebin.mozilla.org/3755622 is a copy if you need one.. anyways, step 1: from trm, you get to know that the pin is part of "core" "SYSCTRL_PADCONF_CORE" as it states for register instance in the trm. step 2: you compute the offset
step 3: you define the pinctrl dt node
step 4: you'd provide the device using it reference - rather trivial ;)
(quoted diff) +0 -0
b/arch/arm/boot/dts/omap4-panda-es.dts
index 56c4354..8f8d36c 100644
arch/arm/boot/dts/omap4-panda-es.dts +32 -0
@@ -41,6 +41,25 @@ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; + + lsm303d_pins: lsm303d_pins { + pinctrl-single,pins = < + /* + * Example for 4460 device: + * from arch/arm/boot/dts/omap4.dtsi: + * omap4_pmx_core: reg = <0x4a100040 + * the base address --> ^^ + * + * Now, the offset is computed as following: + * Download TRM: http://www.ti.com/lit/ug/swpu235aa/swpu235aa.pdf + * Searching in TRM for MCSPI1_SIMO (page 4145), you see: + * 32 bit register 0x4a100134, it is on the higher 16 bits + * 0x4a100134(SOMI) + 2 (SIMO) = 0x4a100136 + * offset hence is = 0x4a100136 - 0x4a100040 = 0xF6 + */ + 0xF6 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_somi.gpio_139 */ + >; + }; }; &led_wkgpio_pins {
@@ -62,3 +81,16 @@ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; }; }; +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + clock-frequency = <400000>; + + lsm303d@03 { + pinctrl-names = "default"; + pinctrl-0 = <&lsm303d_pins>; + compatible = "st,lsm303d"; + reg = <0x03>; + }; +};
Hi Nishant,
Thank you very much for your suggestions! Now I understand how it works...(I hope) :D
BUT, now I've checked the client->irq in an i2c driver and the value is still 0...
What I have to check?
Thanks,
Denis
Quoted 71 lines · On 12/11/2013 04:39 PM, [email protected] wrote:
Quoted 10 lines · Denis CIOCCA
Hi everybody,
I'm trying to configure an IRQ on pandaboard using device tree but I'm not able to understand how I can do it.
I want to configure the thegpio_139pin and without device tree my command was:
OMAP4_MUX(MCSPI1_SIMO, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),I need to associate it to a i2c device, declared in this way:
here is how you'd figure it out in dt world ;) - it might be a little simpler or harder depending on which end of the development world one is from... (gmail might be screwing up my formatting a little.. so apologies before hand.
http://pastebin.mozilla.org/3755622 is a copy if you need one.. anyways, step 1: from trm, you get to know that the pin is part of "core" "
SYSCTRL_PADCONF_CORE" as it states for register instance in the trm. step 2: you compute the offset
step 3: you define the pinctrl dt node
step 4: you'd provide the device using it reference - rather trivial ;)arch/arm/boot/dts/omap4-panda-es.dts +32
-0@@ -41,6 +41,25 @@ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; + + lsm303d_pins: lsm303d_pins { + pinctrl-single,pins = < + /* + * Example for 4460 device: + * from arch/arm/boot/dts/omap4.dtsi: + * omap4_pmx_core: reg = <0x4a100040 + * the base address --> ^^ + * + * Now, the offset is computed as following: + * Download TRM: http://www.ti.com/lit/ug/swpu235aa/swpu235aa.pdf + * Searching in TRM for MCSPI1_SIMO (page 4145), you see: + * 32 bit register 0x4a100134, it is on the higher 16 bits + * 0x4a100134(SOMI) + 2 (SIMO) = 0x4a100136 + * offset hence is = 0x4a100136 - 0x4a100040 = 0xF6 + */ + 0xF6 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_somi.gpio_139 */ + >; + }; }; &led_wkgpio_pins {@@ -62,3 +81,16 @@ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; }; }; +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + clock-frequency = <400000>; + + lsm303d@03 { + pinctrl-names = "default"; + pinctrl-0 = <&lsm303d_pins>; + compatible = "st,lsm303d"; + reg = <0x03>; + }; +};
Quoted 3 lines · Denis CIOCCA
BUT, now I've checked the
client->irqin an i2c driver and the value is still 0...
I missed this:
Quoted 3 lines
and it works, but I don't know how I can set the interrupt using:
interrupts = <GIC_SPI119IRQ_TYPE_LEVEL_HIGH>; /* example */
<snip>
Quoted 2 lines
What I have to check?
since your interrupt is an GPIO, as an example (probably wont match your case):
interrupt-parent = <&gpio4>; /* '4' is the GPIO BANK */
interrupts = <11 0>; /* '11' maps to the gpio number, '0' (bits -
interrupt-type */
[...]
see Documentation/devicetree/bindings/interrupt-controller/interrupts.txt (hint: b) two cells)
Quoted 2 lines · On 12/11/2013 04:39 PM, [email protected] wrote:
For a future note, please avoid top-posting in mailing lists :)
Signature · 2 lines
Regards, Nishanth Menon
Hi Nishant,
I've configured the device tree as you told me. Now, my device tree code is that:
(quoted diff) +0 -0
b/arch/arm/boot/dts/omap4-panda-es.dts
index 816d1c9..5644260 100644
arch/arm/boot/dts/omap4-panda-es.dts +22 -0
@@ -41,6 +41,12 @@ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; + + lsm6db0_pins: lsm6db0_pins { + pinctrl-single,pins = < + 0xfc (PIN_INPUT | MUX_MODE3) /* mcspi1_cs2.gpio_139 */ + >; + }; }; &led_wkgpio_pins {
@@ -49,6 +55,22 @@ >; }; +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + clock-frequency = <400000>; + + lsm6db0@03 { + pinctrl-names = "default"; + pinctrl-0 = <&lsm6db0_pins>; + compatible = "st,lsm6db0"; + reg = <0x03>; + interrupts = <139 0x1>; + interrupt-parent = <&lsm6db0_pins>; + }; +}; + &leds { pinctrl-0 = < &led_gpio_pins
I've also read the documentation file Documentation/devicetree/bindings/interrupt-controller/interrupts.txt but I'm confused about the gpio muxed with mcspi1.
Do you think my patch is correct?
Thanks,
Denis
Maybe, this is more correctly but still doesn't work...
From 9f6e524fa86834c3ab9a5f710021620a103019b2 Mon Sep 17 00:00:00 2001
From: Denis Ciocca <[email protected]>
Date: Thu, 12 Dec 2013 14:52:39 +0100
Subject: [PATCH] device tree
--- arch/arm/boot/dts/omap4-panda-es.dts | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
(quoted diff) +0 -0
b/arch/arm/boot/dts/omap4-panda-es.dts
index 816d1c9..82c3eb7 100644
arch/arm/boot/dts/omap4-panda-es.dts +22 -0
@@ -41,6 +41,12 @@ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; + + lsm6db0_pins: lsm6db0_pins { + pinctrl-single,pins = < + 0xf6 (PIN_INPUT | MUX_MODE3) /* mcspi1_simo.gpio_136 */ + >; + }; }; &led_wkgpio_pins {
@@ -49,6 +55,22 @@ >; }; +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + clock-frequency = <400000>; + + lsm6db0@03 { + pinctrl-names = "default"; + pinctrl-0 = <&lsm6db0_pins>; + compatible = "st,lsm6db0"; + reg = <0x03>; + interrupts = <&mcspi1 136 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&mcspi1>; + }; +}; + &leds { pinctrl-0 = < &led_gpio_pins
Signature · 7 lines
1.7.9.5 No one can help me? Thanks, Denis
Quoted 37 lines · Denis CIOCCA
Maybe, this is more correctly but still doesn't work...
From
9f6e524fa86834c3ab9a5f710021620a103019b2Mon Sep 17 00:00:00 2001
From: Denis Ciocca <[email protected]>
Date: Thu, 12 Dec 2013 14:52:39 +0100
Subject: [PATCH] device tree--- arch/arm/boot/dts/omap4-panda-es.dts | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)arch/arm/boot/dts/omap4-panda-es.dts +9
-0@@ -41,6 +41,12 @@ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ >; }; + + lsm6db0_pins: lsm6db0_pins { + pinctrl-single,pins = < + 0xf6 (PIN_INPUT | MUX_MODE3) /* mcspi1_simo.gpio_136 */ + >; + }; }; &led_wkgpio_pins {@@ -49,6 +55,22 @@ >; }; +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>;
arch/arm/boot/dts/omap4-panda-es.dts line 70
Quoted 10 lines
arch/arm/boot/dts/omap4-panda-es.dts +10
-0+ + clock-frequency = <400000>; + + lsm6db0@03 { + pinctrl-names = "default"; + pinctrl-0 = <&lsm6db0_pins>; + compatible = "st,lsm6db0"; + reg = <0x03>; + interrupts = <&mcspi1 136 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&mcspi1>;
why is mcspi1 your interrupt parent when you did a padconf for GPIO? you want GPIO136, so you need the right gpio block as the interrupt parent and map interrupts in the correct map.
see [1] for an example (omap2).
arch/arm/boot/dts/omap4-panda-es.dts line 76
Quoted 7 lines
arch/arm/boot/dts/omap4-panda-es.dts +3
-0+ }; +}; + &leds { pinctrl-0 = < &led_gpio_pins
Signature · 2 lines
Regards, Nishanth Menon
Quoted 4 lines
why is mcspi1 your interrupt parent when you did a padconf for GPIO? you want GPIO136, so you need the right gpio block as the interrupt parent and map interrupts in the correct map.
see [1] for an example (omap2).
Oh my god! Now I've understand how device tree works...I'm sorry Nishanth but the dt it's new for me...ok I'm using gpio5 and now it works!
+interrupt-parent = <&gpio5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio line 136 */
Thank you very much for your patience...;)
BR,
Denis
Quoted 11 lines · Denis CIOCCA
Quoted 4 lines
why is mcspi1 your interrupt parent when you did a padconf for GPIO? you want GPIO136, so you need the right gpio block as the interrupt parent and map interrupts in the correct map.
see [1] for an example (omap2).Oh my god! Now I've understand how device tree works...I'm sorry Nishanth but the dt it's new for me...ok I'm using gpio5 and now it works!
(quoted diff) +2
-0+interrupt-parent = <&gpio5>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio line 136 */Thank you very much for your patience...;)
glad to hear it worked, yeah, device tree is a little different, but logical in it's own way.
Regards,
Nishanth Menon