Skip to contentSkip to conversation

nitrogen6x: Move setup_sata to common part

PATCH New Giuseppe Pagano 2 participants 4 messages Nov 28, 2013 – Dec 17, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v4 cover nitrogen6x: Move setup_sata to common part

Move setup_sata function definition from platform file nitrogen6x.c to arch/arm/imx-common/sata.c to avoid code duplication.

CC Stefano Babic <[email protected]>
CC Fabio Estevam <[email protected]>
CC Eric Nelson <[email protected]>

---

Changes in v4:
- Correct Makefile patch to use: obj- instead of COBJS-.

Changes in v3:
- Correct Makefile for filter sata.c to be compiled only for mx6 soc because in function setup_sata there are i.MX6 specific registers definition and this breaks mx5 boards. mx5 boards does not need setup_sata initialization.

Changes in v2:
- Split previous patch between nitrogen6x udoo code changes.

---
 arch/arm/imx-common/Makefile           |    3 +++
 arch/arm/imx-common/sata.c             |   33 ++++++++++++++++++++++++++++++++
 arch/arm/include/asm/imx-common/sata.h |   17 ++++++++++++++++
 board/boundary/nitrogen6x/nitrogen6x.c |   27 +-------------------------
 4 files changed, 54 insertions(+), 26 deletions(-)
 create mode 100644 arch/arm/imx-common/sata.c
 create mode 100644 arch/arm/include/asm/imx-common/sata.h
arch/arm/imx-common/Makefile +3 -0
index 2c80441..68f0f52 100644
@@ -17,6 +17,9 @@ endif
 ifeq ($(SOC),$(filter $(SOC),mx6 mxs))
 obj-y	+= misc.o
 endif
+ifeq ($(SOC),$(filter $(SOC),mx6))
+objs-$(CONFIG_CMD_SATA) += sata.o
+endif
 obj-$(CONFIG_CMD_BMODE) += cmd_bmode.o
 obj-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o
 
arch/arm/imx-common/sata.c new file +33 -0
new file mode 100644
index 0000000..1b4c502
@@ -0,0 +1,33 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/arch/iomux.h>
+#include <asm/io.h>
+
+int setup_sata(void)
+{
+	struct iomuxc_base_regs *const iomuxc_regs
+		= (struct iomuxc_base_regs *)IOMUXC_BASE_ADDR;
+
+	int ret = enable_sata_clock();
+	if (ret)
+		return ret;
+
+	clrsetbits_le32(&iomuxc_regs->gpr[13],
+			IOMUXC_GPR13_SATA_MASK,
+			IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
+			|IOMUXC_GPR13_SATA_PHY_7_SATA2M
+			|IOMUXC_GPR13_SATA_SPEED_3G
+			|(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
+			|IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
+			|IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16
+			|IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB
+			|IOMUXC_GPR13_SATA_PHY_2_TX_1P104V
+			|IOMUXC_GPR13_SATA_PHY_1_SLOW);
+
+	return 0;
+}
arch/arm/include/asm/imx-common/sata.h new file +17 -0
new file mode 100644
index 0000000..8bb4493
@@ -0,0 +1,17 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __IMX_SATA_H_
+#define __IMX_SATA_H_
+
+/*
+ * SATA setup for i.mx6 quad based platform
+ */
+
+int setup_sata(void);
+
+#endif
+
board/boundary/nitrogen6x/nitrogen6x.c +1 -26
index 616ad55..3f4cfa1 100644
@@ -17,6 +17,7 @@
 #include <asm/gpio.h>
 #include <asm/imx-common/iomux-v3.h>
 #include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/sata.h>
 #include <asm/imx-common/boot_mode.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
@@ -401,32 +402,6 @@ static void setup_buttons(void)
 					 ARRAY_SIZE(button_pads));
 }
 
-#ifdef CONFIG_CMD_SATA
-
-int setup_sata(void)
-{
-	struct iomuxc_base_regs *const iomuxc_regs
-		= (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR;
-	int ret = enable_sata_clock();
-	if (ret)
-		return ret;
-
-	clrsetbits_le32(&iomuxc_regs->gpr[13],
-			IOMUXC_GPR13_SATA_MASK,
-			IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
-			|IOMUXC_GPR13_SATA_PHY_7_SATA2M
-			|IOMUXC_GPR13_SATA_SPEED_3G
-			|(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
-			|IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
-			|IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16
-			|IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB
-			|IOMUXC_GPR13_SATA_PHY_2_TX_1P104V
-			|IOMUXC_GPR13_SATA_PHY_1_SLOW);
-
-	return 0;
-}
-#endif
-
 #if defined(CONFIG_VIDEO_IPUV3)
 
 static iomux_v3_cfg_t const backlight_pads[] = {
Signature · 1 line
1.7.10.4
#1 lore raw

PATCH v4 1/1 udoo: Add SATA support on uDoo Board.

Add SATA support on uDoo Board.

CC Stefano Babic <[email protected]>
CC Fabio Estevam <[email protected]>

---

Changes in v4:
- No changes.

Changes in v3:
- No changes.

Changes in v2:
- Split previous patch between nitrogen6x udoo code changes.

---
 board/udoo/udoo.c      |    4 ++++
 include/configs/udoo.h |   12 ++++++++++++
 2 files changed, 16 insertions(+)
board/udoo/udoo.c +4 -0
index 081d517..e9236d4 100644
@@ -14,6 +14,7 @@
 #include <asm/errno.h>
 #include <asm/gpio.h>
 #include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/sata.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
 #include <asm/arch/crm_regs.h>
@@ -240,6 +241,9 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+#ifdef CONFIG_CMD_SATA
+	setup_sata();
+#endif
 	return 0;
 }
 
include/configs/udoo.h +12 -0
index b9a493c..a1a1750 100644
@@ -34,6 +34,18 @@
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART2_BASE
 
+/* SATA Configs */
+
+#define CONFIG_CMD_SATA
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
 /* Network support */
 
 #define CONFIG_CMD_PING
Signature · 1 line
1.7.10.4
#2 lore raw

PATCH v4 1/1 udoo: Add SATA support on uDoo Board.

Quoted 7 lines · Giuseppe Pagano

Add SATA support on uDoo Board.

CC Stefano Babic <[email protected]>
CC Fabio Estevam <[email protected]>

---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw

v4 cover nitrogen6x: Move setup_sata to common part

In reply to Giuseppe Pagano
Quoted 8 lines · Giuseppe Pagano

Move setup_sata function definition from platform file nitrogen6x.c to arch/arm/imx-common/sata.c to avoid code duplication.

CC Stefano Babic <[email protected]>
CC Fabio Estevam <[email protected]>
CC Eric Nelson <[email protected]>

---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================