configs: imx: Remove CONFIG_SYS_SPD_BUS_NUM option
Fabio Estevam
reviewerPATCH 1/1 configs: imx: Remove CONFIG_SYS_SPD_BUS_NUM option
From: Fabio Estevam <[email protected]>
According to the README:
"- CONFIG_SYS_SPD_BUS_NUM
If SPD EEPROM is on an I2C bus other than the first one, specify here. Note that the value must resolve to something your driver can deal with."
There is no SPD EEPROM on the imx boards, so ged rid of this option.
--- include/configs/imx31_phycore.h | 1 - include/configs/mx25pdk.h | 1 - include/configs/mx35pdk.h | 1 - include/configs/mx53ard.h | 1 - include/configs/mx53evk.h | 1 - include/configs/mx53loco.h | 1 - include/configs/mx53smd.h | 1 - 7 files changed, 7 deletions(-)
include/configs/imx31_phycore.h +0 -1
@@ -37,7 +37,6 @@#define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ #define CONFIG_SYS_I2C_CLK_OFFSET I2C2_CLK_OFFSET#define CONFIG_MXC_UART
include/configs/mx25pdk.h +0 -1
@@ -115,7 +115,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ /* RTC */ #define CONFIG_RTC_IMXDI
include/configs/mx35pdk.h +0 -1
@@ -42,7 +42,6 @@*/ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ #define CONFIG_MXC_SPI #define CONFIG_MXC_GPIO
include/configs/mx53ard.h +0 -1
@@ -46,7 +46,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* MMC Configs */ #define CONFIG_FSL_ESDHC
include/configs/mx53evk.h +0 -1
@@ -39,7 +39,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* PMIC Configs */ #define CONFIG_POWER
include/configs/mx53loco.h +0 -1
@@ -73,7 +73,6 @@/* I2C Configs */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ /* PMIC Controller */ #define CONFIG_POWER
include/configs/mx53smd.h +0 -1
@@ -36,7 +36,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* MMC Configs */ #define CONFIG_FSL_ESDHC
Signature · 1 line
1.8.1.2
PATCH 1/1 configs: imx: Remove CONFIG_SYS_SPD_BUS_NUM option
Quoted 100 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
According to the README:
"-
CONFIG_SYS_SPD_BUS_NUM
If SPD EEPROM is on an I2C bus other than the first one, specify here. Note that the value must resolve to something your driver can deal with."There is no SPD EEPROM on the imx boards, so ged rid of this option.
Signed-off-by Fabio Estevam <[email protected]>--- include/configs/imx31_phycore.h | 1 - include/configs/mx25pdk.h | 1 - include/configs/mx35pdk.h | 1 - include/configs/mx53ard.h | 1 - include/configs/mx53evk.h | 1 - include/configs/mx53loco.h | 1 - include/configs/mx53smd.h | 1 - 7 files changed, 7 deletions(-)include/configs/imx31_phycore.h +0
-1@@ -37,7 +37,6 @@#define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ #define CONFIG_SYS_I2C_CLK_OFFSET I2C2_CLK_OFFSET#define CONFIG_MXC_UART include/configs/mx25pdk.h +0
-1@@ -115,7 +115,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ /* RTC */ #define CONFIG_RTC_IMXDI include/configs/mx35pdk.h +0
-1@@ -42,7 +42,6 @@*/ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ #define CONFIG_MXC_SPI #define CONFIG_MXC_GPIO include/configs/mx53ard.h +0
-1@@ -46,7 +46,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* MMC Configs */ #define CONFIG_FSL_ESDHC include/configs/mx53evk.h +0
-1@@ -39,7 +39,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* PMIC Configs */ #define CONFIG_POWER include/configs/mx53loco.h +0
-1@@ -73,7 +73,6 @@/* I2C Configs */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0/* I2C1 */ /* PMIC Controller */ #define CONFIG_POWER include/configs/mx53smd.h +0
-0
include/configs/mx53smd.h line 41
Quoted 7 lines
include/configs/mx53smd.h +0
-1@@ -36,7 +36,6 @@#define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 1/* I2C2 */ /* MMC Configs */ #define CONFIG_FSL_ESDHC
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/1 configs: imx: Remove CONFIG_SYS_SPD_BUS_NUM option
In reply to Fabio EstevamQuoted 9 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
According to the README:
"-
CONFIG_SYS_SPD_BUS_NUM
If SPD EEPROM is on an I2C bus other than the first one, specify here. Note that the value must resolve to something your driver can deal with."
Quoted 4 lines
There is no SPD EEPROM on the imx boards, so ged rid of this option.
Signed-off-by Fabio Estevam <[email protected]>---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================