Skip to contentSkip to conversation

EXYNOS5420: Add SMDK5420 board support

PATCH Superseded Rajeshwari S Shinde 3 participants 14 messages Dec 20, 2013 – Dec 23, 2013

Subsystems (2)

v12 of 13 Superseded Latest is v13 →

lore
Share & tools
lore
#0 lore raw

v12 cover EXYNOS5420: Add SMDK5420 board support

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.

Changes in V2:
- Corrected a compilation issue for SMDK5420.

Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.

Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.

Changes in V5:
- Moved functions board_mmc_init and board_eth_init to common/board.c in case of device tree support.

Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU to arch/arm dwmmc.h

Changes in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.

Changes in V8:
- corrected the if loops with if conditions of pro_id and cpu_id.

Changes in V9:
- Added macros to get the base address
- Rebased on latest code.

Changes in V10:
- Added new structures for Power and DMC registers for 5420.
- Changed the input parameters for common dmc functions.
- Removed unnecesarry blank lines and added where ever required.

Changes in V11:
-Rebased on latest u-boot-samsung branch.

Changes in V12:
- Changed const void * pointers to uint32_t *.

Rajeshwari S Shinde (11):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
EXYNOS5420: Add power register structure.
EXYNOS5420: Add dmc and phy_control register structure
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support

 arch/arm/cpu/armv7/exynos/clock.c              | 279 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 ++++++++++-
 arch/arm/cpu/armv7/exynos/dmc_common.c         |  60 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c      | 439 ++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 764 ++++++++++++++++------
 arch/arm/cpu/armv7/exynos/pinmux.c             | 260 +++++++-
 arch/arm/dts/exynos5.dtsi                      | 198 ++++++
 arch/arm/dts/exynos5250.dtsi                   | 194 +-----
 arch/arm/dts/exynos5420.dtsi                   |  70 +++
 arch/arm/include/asm/arch-exynos/board.h       |  17 +
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h         |  52 +-
 arch/arm/include/asm/arch-exynos/dmc.h         | 177 ++++++
 arch/arm/include/asm/arch-exynos/gpio.h        | 143 ++++-
 arch/arm/include/asm/arch-exynos/periph.h      |   3 +
 arch/arm/include/asm/arch-exynos/power.h       | 837 +++++++++++++++++++++++++
 board/samsung/common/Makefile                  |   4 +
 board/samsung/common/board.c                   | 410 ++++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts      | 169 +++++
 board/samsung/smdk5250/exynos5-dt.c            | 352 +----------
 board/samsung/smdk5250/smdk5250.c              | 182 +-----
 board/samsung/smdk5420/Makefile                |  11 +
 board/samsung/smdk5420/smdk5420.c              | 159 +++++
 board/samsung/smdk5420/smdk5420_spl.c          |  52 ++
 boards.cfg                                     |   1 +
 include/configs/arndale.h                      |   1 +
 include/configs/exynos5-dt.h                   | 289 +++++++++
 include/configs/exynos5250-dt.h                | 283 +--------
 include/configs/smdk5420.h                     |  56 ++
 spl/Makefile                                   |   7 +-
 tools/Makefile                                 |   3 +-
 tools/mkexynosspl.c                            | 167 +++--
 34 files changed, 5188 insertions(+), 1315 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h
Signature · 1 line
1.7.12.4
#1 lore raw

PATCH v12 1/11 EXYNOS5: Create a common board file

Create a common board.c file for all functions which are common across all EXYNOS5 platforms.

exynos_init function is provided for platform specific code.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added check for the compilation of MAX77686 pmic.
Changes in V5:
- Moved board_eth_init and board_mmc_init in case of device tree support
Changes in V6:
- None.
Changes in V7:
- None
Changes in V8:
- None
Changes in V9:
- Reabsed on latest code.
Changes in V10:
- Corrected coding style nits.
Changes in V11:
-Rebased on latest u-boot-samsung tree
Chnages in V12:
- None

 arch/arm/include/asm/arch-exynos/board.h |  17 ++
 board/samsung/common/Makefile            |   4 +
 board/samsung/common/board.c             | 408 +++++++++++++++++++++++++++++++
 board/samsung/smdk5250/exynos5-dt.c      | 352 +-------------------------
 board/samsung/smdk5250/smdk5250.c        | 182 +-------------
 include/configs/exynos5250-dt.h          |   2 +
 6 files changed, 436 insertions(+), 529 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
arch/arm/include/asm/arch-exynos/board.h new file +17 -0
new file mode 100644
index 0000000..243fb12
@@ -0,0 +1,17 @@
+/*
+ * (C) Copyright 2013 Samsung Electronics
+ * Rajeshwari Shinde <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _EXYNOS_BOARD_H
+#define _EXYNOS_BOARD_H
+
+/*
+ * Exynos baord specific changes for
+ * board_init
+ */
+int exynos_init(void);
+
+#endif	/* EXYNOS_BOARD_H */
board/samsung/common/Makefile +4 -0
index 501d974..22bd6b1 100644
@@ -8,3 +8,7 @@
 obj-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o
 obj-$(CONFIG_THOR_FUNCTION) += thor.o
 obj-$(CONFIG_CMD_USB_MASS_STORAGE) += ums.o
+
+ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_BOARD_COMMON)	+= board.o
+endif
board/samsung/common/board.c new file +408 -0

408 lines not on this page · raw message

board/samsung/smdk5250/exynos5-dt.c +2 -350

381 lines not on this page · raw message

board/samsung/smdk5250/smdk5250.c +3 -179

219 lines not on this page · raw message

include/configs/exynos5250-dt.h +2 -0
index dee18a7..c625524 100644
@@ -21,6 +21,8 @@
 #define CONFIG_ARCH_CPU_INIT
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_COMMON
+#define CONFIG_ARCH_EARLY_INIT_R
 
 /* Enable fdt support for Exynos5250 */
 #define CONFIG_OF_CONTROL
Signature · 1 line
1.7.12.4
#2 lore raw

PATCH v12 1/11 EXYNOS5: Create a common board file

Dear Rajeshwari S Shinde,

Quoted 31 lines · Rajeshwari S Shinde

Create a common board.c file for all functions which are common across all EXYNOS5 platforms.

exynos_init function is provided for platform specific code.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added check for the compilation of MAX77686 pmic.
Changes in V5:
- Moved board_eth_init and board_mmc_init in case of device tree support
Changes in V6:
- None.
Changes in V7:
- None
Changes in V8:
- None
Changes in V9:
- Reabsed on latest code.
Changes in V10:
- Corrected coding style nits.
Changes in V11:
-Rebased on latest u-boot-samsung tree
Chnages in V12:
- None

Quoted 9 lines
 arch/arm/include/asm/arch-exynos/board.h |  17 ++
 board/samsung/common/Makefile            |   4 +
 board/samsung/common/board.c             | 408 +++++++++++++++++++++++++++++++
 board/samsung/smdk5250/exynos5-dt.c      | 352 +-------------------------
 board/samsung/smdk5250/smdk5250.c        | 182 +-------------
 include/configs/exynos5250-dt.h          |   2 +
 6 files changed, 436 insertions(+), 529 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c

Sorry but patch failed.

u-boot-samsung (master)$ patch --dry-run -p1 < U-Boot-01-11-V12-EXYNOS5-Create-a-common-board-file.patch patching file arch/arm/include/asm/arch-exynos/board.h
patching file board/samsung/common/Makefile
patching file board/samsung/common/board.c
patching file board/samsung/smdk5250/exynos5-dt.c
Hunk #2 FAILED at 37.
Hunk #3 succeeded at 307 (offset -2 lines).
Hunk #4 succeeded at 330 (offset -2 lines).
1 out of 4 hunks FAILED -- saving rejects to file board/samsung/smdk5250/exynos5-dt.c.rej patching file board/samsung/smdk5250/smdk5250.c
patching file include/configs/exynos5250-dt.h

Piotr's patch seems affected your patch.

commit 2d8f1e27695a8a9a3ed863a510be58284b6b411c

Author: Piotr Wilczek <[email protected]>
Date:   Wed Nov 20 10:43:49 2013 +0100

driver:i2c:s3c24x0: adapt driver to new i2c

Quoted 78 lines
arch/arm/include/asm/arch-exynos/board.h new file +17 -0
new file mode 100644
index 0000000..243fb12
@@ -0,0 +1,17 @@
+/*
+ * (C) Copyright 2013 Samsung Electronics
+ * Rajeshwari Shinde <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _EXYNOS_BOARD_H
+#define _EXYNOS_BOARD_H
+
+/*
+ * Exynos baord specific changes for
+ * board_init
+ */
+int exynos_init(void);
+
+#endif	/* EXYNOS_BOARD_H */
board/samsung/common/Makefile +4 -0
index 501d974..22bd6b1 100644
@@ -8,3 +8,7 @@
 obj-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o
 obj-$(CONFIG_THOR_FUNCTION) += thor.o
 obj-$(CONFIG_CMD_USB_MASS_STORAGE) += ums.o
+
+ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_BOARD_COMMON)	+= board.o
+endif
board/samsung/common/board.c new file +36 -0
new file mode 100644
index 0000000..95df346
@@ -0,0 +1,408 @@
+/*
+ * (C) Copyright 2013 SAMSUNG Electronics
+ * Rajeshwari Shinde <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <cros_ec.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <spi.h>
+#include <tmu.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <power/pmic.h>
+#include <asm/arch/sromc.h>
+#include <power/max77686_pmic.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct local_info {
+	struct cros_ec_dev *cros_ec_dev;	/* Pointer to cros_ec device */
+	int cros_ec_err;			/* Error for cros_ec, 0 if ok */
+};
+
+static struct local_info local;
+
+#if defined CONFIG_EXYNOS_TMU

board/samsung/common/board.c line 46

Quoted 10 lines
board/samsung/common/board.c new file +10 -0
+/* Boot Time Thermal Analysis for SoC temperature threshold breach */
+static void boot_temp_check(void)
+{
+	int temp;
+
+	switch (tmu_monitor(&temp)) {
+	case TMU_STATUS_NORMAL:
+		break;
+	case TMU_STATUS_TRIPPED:
+	/* Status TRIPPED ans WARNING means corresponding threshold breach */

It's a minor issue.
Could please fix indentations?

board/samsung/common/board.c line 58

Quoted 12 lines
board/samsung/common/board.c new file +12 -0
+		puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
+		set_ps_hold_ctrl();
+		hang();
+		break;
+	case TMU_STATUS_WARNING:
+		puts("EXYNOS_TMU: WARNING! Temperature very high\n");
+		break;
+	case TMU_STATUS_INIT:
+	/*
+	 * TMU_STATUS_INIT means something is wrong with temperature sensing
+	 * and TMU status was changed back from NORMAL to INIT.
+	 */

ditto.

Quoted 340 lines
board/samsung/common/board.c new file +340 -0
+		puts("EXYNOS_TMU: WARNING! Temperature sensing not done\n");
+		break;
+	default:
+		debug("EXYNOS_TMU: Unknown TMU state\n");
+	}
+}
+#endif
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+#if defined CONFIG_EXYNOS_TMU
+	if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
+		debug("%s: Failed to init TMU\n", __func__);
+		return -1;
+	}
+	boot_temp_check();
+#endif
+
+#ifdef CONFIG_EXYNOS_SPI
+	spi_init();
+#endif
+	return exynos_init();
+}
+
+int dram_init(void)
+{
+	int i;
+	u32 addr;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+	}
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	int i;
+	u32 addr, size;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+		gd->bd->bi_dram[i].start = addr;
+		gd->bd->bi_dram[i].size = size;
+	}
+}
+
+static int board_uart_init(void)
+{
+	int err, uart_id, ret = 0;
+
+	for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+		err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+		if (err) {
+			debug("UART%d not configured\n",
+			      (uart_id - PERIPH_ID_UART0));
+			ret |= err;
+		}
+	}
+	return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+	int err;
+
+	err = board_uart_init();
+	if (err) {
+		debug("UART init failed\n");
+		return err;
+	}
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+	board_i2c_init(gd->fdt_blob);
+#endif
+
+	return err;
+}
+#endif
+
+struct cros_ec_dev *board_get_cros_ec_dev(void)
+{
+	return local.cros_ec_dev;
+}
+
+static int board_init_cros_ec_devices(const void *blob)
+{
+	local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev);
+	if (local.cros_ec_err)
+		return -1;  /* Will report in board_late_init() */
+
+	return 0;
+}
+
+#if defined(CONFIG_POWER)
+#ifdef CONFIG_POWER_MAX77686
+static int pmic_reg_update(struct pmic *p, int reg, uint regval)
+{
+	u32 val;
+	int ret = 0;
+
+	ret = pmic_reg_read(p, reg, &val);
+	if (ret) {
+		debug("%s: PMIC %d register read failed\n", __func__, reg);
+		return -1;
+	}
+	val |= regval;
+	ret = pmic_reg_write(p, reg, val);
+	if (ret) {
+		debug("%s: PMIC %d register write failed\n", __func__, reg);
+		return -1;
+	}
+	return 0;
+}
+
+static int max77686_init(void)
+{
+	struct pmic *p;
+
+	if (pmic_init(I2C_PMIC))
+		return -1;
+
+	p = pmic_get("MAX77686_PMIC");
+	if (!p)
+		return -ENODEV;
+
+	if (pmic_probe(p))
+		return -1;
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN))
+		return -1;
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT,
+			    MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V))
+		return -1;
+
+	/* VDD_MIF */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT,
+			   MAX77686_BUCK1OUT_1V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK1OUT);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL,
+			    MAX77686_BUCK1CTRL_EN))
+		return -1;
+
+	/* VDD_ARM */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1,
+			   MAX77686_BUCK2DVS1_1_3V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK2DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1,
+			    MAX77686_BUCK2CTRL_ON))
+		return -1;
+
+	/* VDD_INT */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1,
+			   MAX77686_BUCK3DVS1_1_0125V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK3DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL,
+			    MAX77686_BUCK3CTRL_ON))
+		return -1;
+
+	/* VDD_G3D */
+	if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1,
+			   MAX77686_BUCK4DVS1_1_2V)) {
+		debug("%s: PMIC %d register write failed\n", __func__,
+		      MAX77686_REG_PMIC_BUCK4DVS1);
+		return -1;
+	}
+
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1,
+			    MAX77686_BUCK3CTRL_ON))
+		return -1;
+
+	/* VDD_LDO2 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1,
+			    MAX77686_LD02CTRL1_1_5V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO3 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1,
+			    MAX77686_LD03CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO5 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1,
+			    MAX77686_LD05CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	/* VDD_LDO10 */
+	if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1,
+			    MAX77686_LD10CTRL1_1_8V | EN_LDO))
+		return -1;
+
+	return 0;
+}
+#endif
+
+int power_init_board(void)
+{
+	int ret = 0;
+
+	set_ps_hold_ctrl();
+
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+#ifdef CONFIG_POWER_MAX77686
+	ret = max77686_init();
+#endif
+
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_OF_CONTROL
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+	int err;
+	int node;
+
+	node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+	if (node < 0) {
+		debug("Could not find SROMC node\n");
+		return node;
+	}
+
+	config->bank = fdtdec_get_int(blob, node, "bank", 0);
+	config->width = fdtdec_get_int(blob, node, "width", 2);
+
+	err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+			FDT_SROM_TIMING_COUNT);
+	if (err < 0) {
+		debug("Could not decode SROMC configuration Error: %s\n",
+		      fdt_strerror(err));
+		return -FDT_ERR_NOTFOUND;
+	}
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+	u32 smc_bw_conf, smc_bc_conf;
+	struct fdt_sromc config;
+	fdt_addr_t base_addr;
+	int node;
+
+	node = decode_sromc(gd->fdt_blob, &config);
+	if (node < 0) {
+		debug("%s: Could not find sromc configuration\n", __func__);
+		return 0;
+	}
+	node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+	if (node < 0) {
+		debug("%s: Could not find lan9215 configuration\n", __func__);
+		return 0;
+	}
+
+	/* We now have a node, so any problems from now on are errors */
+	base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+	if (base_addr == FDT_ADDR_T_NONE) {
+		debug("%s: Could not find lan9215 address\n", __func__);
+		return -1;
+	}
+
+	/* Ethernet needs data bus width of 16 bits */
+	if (config.width != 2) {
+		debug("%s: Unsupported bus width %d\n", __func__,
+		      config.width);
+		return -1;
+	}
+	smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+			| SROMC_BYTE_ENABLE(config.bank);
+
+	smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS])   |
+			SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
+			SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
+			SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
+			SROMC_BC_TAH(config.timing[FDT_SROM_TAH])   |
+			SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
+			SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+	/* Select and configure the SROMC bank */
+	exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+	s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+	return smc911x_initialize(0, base_addr);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+
+	/* dwmmc initializattion for available channels */
+	ret = exynos_dwmmc_init(gd->fdt_blob);
+	if (ret)
+		debug("dwmmc init failed\n");
+
+	return ret;
+}
+#endif
+#endif
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	stdio_print_current_devices();
+
+	if (local.cros_ec_err) {
+		/* Force console on */
+		gd->flags &= ~GD_FLG_SILENT;
+
+		printf("cros-ec communications failure %d\n",
+		       local.cros_ec_err);
+		puts("\nPlease reset with Power+Refresh\n\n");
+		panic("Cannot init cros-ec device");
+		return -1;
+	}
+	return 0;
+}
+#endif
+
+int arch_early_init_r(void)

board/samsung/common/board.c line 408

Quoted 10 lines
board/samsung/common/board.c new file +10 -0
+{
+#ifdef CONFIG_CROS_EC
+	if (board_init_cros_ec_devices(gd->fdt_blob)) {
+		printf("%s: Failed to init EC\n", __func__);
+		return 0;
+	}
+#endif
+
+	return 0;
+}

Thanks,
Minkyu Kang.

#3 lore raw

PATCH v12 2/11 Exynos5420: Add base addresses for 5420

In reply to Rajeshwari S Shinde

Adds base addresses of various IPs and controllers required for Exynos5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added base address for TZPC.
Changes in V5:
- None
Chnages in V6:
- Rebased on latest samsung mainline branch.
Changes in V7:
- Corrected the comments
Changes in V8:
- None
Changes in V9:
- None
Changes in V10:
- None
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/include/asm/arch-exynos/cpu.h | 49 +++++++++++++++++++++++++++++++++-
 1 file changed, 48 insertions(+), 1 deletion(-)
arch/arm/include/asm/arch-exynos/cpu.h +48 -1
index b4ef03e..2b44210 100644
@@ -92,7 +92,7 @@
 #define EXYNOS4X12_USB_HOST_XHCI_BASE	DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_USB3PHY_BASE		DEVICE_NOT_AVAILABLE
 
-/* EXYNOS5 Common*/
+/* EXYNOS5 */
 #define EXYNOS5_I2C_SPACING		0x10000
 
 #define EXYNOS5_AUDIOSS_BASE		0x03810000
@@ -130,6 +130,46 @@
 #define EXYNOS5_ADC_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS5_MODEM_BASE		DEVICE_NOT_AVAILABLE
 
+/* EXYNOS5420 */
+#define EXYNOS5420_AUDIOSS_BASE		0x03810000
+#define EXYNOS5420_GPIO_PART5_BASE	0x03860000
+#define EXYNOS5420_PRO_ID		0x10000000
+#define EXYNOS5420_CLOCK_BASE		0x10010000
+#define EXYNOS5420_POWER_BASE		0x10040000
+#define EXYNOS5420_SWRESET		0x10040400
+#define EXYNOS5420_SYSREG_BASE		0x10050000
+#define EXYNOS5420_TZPC_BASE		0x100E0000
+#define EXYNOS5420_WATCHDOG_BASE	0x101D0000
+#define EXYNOS5420_ACE_SFR_BASE		0x10830000
+#define EXYNOS5420_DMC_PHY_BASE		0x10C00000
+#define EXYNOS5420_DMC_CTRL_BASE	0x10C20000
+#define EXYNOS5420_DMC_TZASC0_BASE	0x10D40000
+#define EXYNOS5420_DMC_TZASC1_BASE	0x10D50000
+#define EXYNOS5420_USB_HOST_EHCI_BASE	0x12110000
+#define EXYNOS5420_MMC_BASE		0x12200000
+#define EXYNOS5420_SROMC_BASE		0x12250000
+#define EXYNOS5420_UART_BASE		0x12C00000
+#define EXYNOS5420_I2C_BASE		0x12C60000
+#define EXYNOS5420_I2C_8910_BASE	0x12E00000
+#define EXYNOS5420_SPI_BASE		0x12D20000
+#define EXYNOS5420_I2S_BASE		0x12D60000
+#define EXYNOS5420_PWMTIMER_BASE	0x12DD0000
+#define EXYNOS5420_SPI_ISP_BASE		0x131A0000
+#define EXYNOS5420_GPIO_PART2_BASE	0x13400000
+#define EXYNOS5420_GPIO_PART3_BASE	0x13410000
+#define EXYNOS5420_GPIO_PART4_BASE	0x14000000
+#define EXYNOS5420_GPIO_PART1_BASE	0x14010000
+#define EXYNOS5420_MIPI_DSIM_BASE	0x14500000
+#define EXYNOS5420_DP_BASE		0x145B0000
+
+#define EXYNOS5420_USBPHY_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_USBOTG_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_FIMD_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_ADC_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_MODEM_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_USB3PHY_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_USB_HOST_XHCI_BASE	DEVICE_NOT_AVAILABLE
+
 #ifndef __ASSEMBLY__
 #include <asm/io.h>
 /* CPU detection macros */
@@ -163,6 +203,10 @@ static inline void s5p_set_cpu_id(void)
 		/* Exynos5250 */
 		s5p_cpu_id = 0x5250;
 		break;
+	case 0x420:
+		/* Exynos5420 */
+		s5p_cpu_id = 0x5420;
+		break;
 	}
 }
 
@@ -190,6 +234,7 @@ static inline int __attribute__((no_instrument_function)) \
 IS_EXYNOS_TYPE(exynos4210, 0x4210)
 IS_EXYNOS_TYPE(exynos4412, 0x4412)
 IS_EXYNOS_TYPE(exynos5250, 0x5250)
+IS_EXYNOS_TYPE(exynos5420, 0x5420)
 
 #define SAMSUNG_BASE(device, base)				\
 static inline unsigned int __attribute__((no_instrument_function)) \
@@ -200,6 +245,8 @@ static inline unsigned int __attribute__((no_instrument_function)) \
 			return EXYNOS4X12_##base;		\
 		return EXYNOS4_##base;				\
 	} else if (cpu_is_exynos5()) {				\
+		if (proid_is_exynos5420())			\
+			return EXYNOS5420_##base;		\
 		return EXYNOS5_##base;				\
 	}							\
 	return 0;						\
Signature · 1 line
1.7.12.4
#4 lore raw

PATCH v12 3/11 EXYNOS5420: Add power register structure.

In reply to Rajeshwari S Shinde

Add structure for power register for Exynos5420

---
Changes in V10:
- New patch
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++++++++
 1 file changed, 837 insertions(+)
arch/arm/include/asm/arch-exynos/power.h +837 -0
index 2bfee18..c9609a2 100644
@@ -831,6 +831,843 @@ struct exynos5_power {
 	unsigned int	cmu_reset_mau_option;
 	unsigned char	res163[0x24];
 };
+
+struct exynos5420_power {
+	unsigned int	om_stat;
+	unsigned int	lpi_mask0;
+	unsigned int	lpi_mask1;
+	unsigned char	res1[0x10];
+	unsigned int	rtc_clko_sel;
+	unsigned char	res2[0x1e0];
+	unsigned int	central_seq_configuration;
+	unsigned int	central_seq_status;
+	unsigned int	central_seq_option;
+	unsigned char	res3[0x14];
+	unsigned int	seq_transition0;
+	unsigned int	seq_transition1;
+	unsigned int	seq_transition2;
+	unsigned int	seq_transition3;
+	unsigned int	seq_transition4;
+	unsigned int	seq_transition5;
+	unsigned int	seq_transition6;
+	unsigned int	seq_transition7;
+	unsigned int	central_seq_coreblk_configuration;
+	unsigned int	central_seq_coreblk_status;
+	unsigned int	central_seq_coreblk_option;
+	unsigned char	res4[0x14];
+	unsigned int	seq_coreblk_transition0;
+	unsigned int	seq_coreblk_transition1;
+	unsigned int	seq_coreblk_transition2;
+	unsigned int	seq_coreblk_transition3;
+	unsigned int	seq_coreblk_transition4;
+	unsigned int	seq_coreblk_transition5;
+	unsigned int	seq_coreblk_transition6;
+	unsigned int	seq_coreblk_transition7;
+	unsigned char	res5[0x180];
+	unsigned int	swreset;
+	unsigned int	rst_stat;
+	unsigned int	automatic_wdt_reset_disable;
+	unsigned int	mask_wdt_reset_request;
+	unsigned int	mask_wreset_request;
+	unsigned char	res6[0xec];
+	unsigned int	reset_sequencer_configuration;
+	unsigned int	reset_sequencer_status;
+	unsigned int	reset_sequencer_option;
+	unsigned char	res7[0xf4];
+	unsigned int	wakeup_stat;
+	unsigned int	eint_wakeup_mask;
+	unsigned int	wakeup_mask;
+	unsigned int	wakeup_interrupt;
+	unsigned char	res8[0x10];
+	unsigned int	wakeup_stat_coreblk;
+	unsigned int	eint_wakeup_mask_coreblk;
+	unsigned int	wakeup_mask_coreblk;
+	unsigned int	wakeup_interrupt_coreblk;
+	unsigned char	res9[0xd0];
+	unsigned int	hdmi_phy_control;
+	unsigned int	usbdev_phy_control;
+	unsigned int	usbdev1_phy_control;
+	unsigned int	usbhost_phy_control;
+	unsigned char	res104[0x4];
+	unsigned int	mipi_phy0_control;
+	unsigned int	mipi_phy1_control;
+	unsigned int	mipi_phy2_control;
+	unsigned int	adc_phy_control;
+	unsigned int	mtcadc_phy_control;
+	unsigned int	dptx_phy_control;
+	unsigned char	res10[0xd4];
+	unsigned int	inform0;
+	unsigned int	inform1;
+	unsigned int	inform2;
+	unsigned int	inform3;
+	unsigned int	sysip_dat0;
+	unsigned int	sysip_dat1;
+	unsigned int	sysip_dat2;
+	unsigned int	sysip_dat3;
+	unsigned char	res11[0xe0];
+	unsigned int	pmu_spare0;
+	unsigned int	pmu_spare1;
+	unsigned int	pmu_spare2;
+	unsigned int	pmu_spare3;
+	unsigned char	res12[0x4];
+	unsigned int	cg_status0;
+	unsigned int	cg_status1;
+	unsigned int	cg_status2;
+	unsigned int	cg_status3;
+	unsigned int	cg_status4;
+	unsigned char	res200[0x58];
+	unsigned int	irom_data_reg0;
+	unsigned int	irom_data_reg1;
+	unsigned int	irom_data_reg2;
+	unsigned int	irom_data_reg3;
+	unsigned char	res13[0x70];
+	unsigned int	pmu_debug;
+	unsigned char	res14[0x5fc];
+	unsigned int	arm_core0_sys_pwr_reg;
+	unsigned char	res500[0xc];
+	unsigned int	arm_core1_sys_pwr_reg;
+	unsigned char	res501[0xc];
+	unsigned int	arm_core2_sys_pwr_reg;
+	unsigned char	res502[0xc];
+	unsigned int	arm_core3_sys_pwr_reg;
+	unsigned char	res503[0xc];
+	unsigned int	kfc_core0_sys_pwr_reg;
+	unsigned char	res504[0xc];
+	unsigned int	kfc_core1_sys_pwr_reg;
+	unsigned char	res505[0xc];
+	unsigned int	kfc_core2_sys_pwr_reg;
+	unsigned char	res506[0xc];
+	unsigned int	kfc_core3_sys_pwr_reg;
+	unsigned char	res507[0x1c];
+	unsigned int	isp_arm_sys_pwr_reg;
+	unsigned char	res18[0xc];
+	unsigned int	arm_common_sys_pwr_reg;
+	unsigned char	res508[0xc];
+	unsigned int	kfc_common_sys_pwr_reg;
+	unsigned char	res19[0xc];
+	unsigned int	arm_l2_sys_pwr_reg;
+	unsigned char	res509[0xc];
+	unsigned int	kfc_l2_sys_pwr_reg;
+	unsigned char	res20[0xc];
+	unsigned int	cmu_cpu_aclkstop_sys_pwr_reg;
+	unsigned int	cmu_cpu_sclkstop_sys_pwr_reg;
+	unsigned char	res510[0x8];
+	unsigned int	cmu_kfc_aclkstop_sys_pwr_reg;
+	unsigned char	res511[0xc];
+	unsigned int	cmu_aclkstop_sys_pwr_reg;
+	unsigned int	cmu_sclkstop_sys_pwr_reg;
+	unsigned char	res21[0x4];
+	unsigned int	cmu_reset_sys_pwr_reg;
+	unsigned char	res22[0x10];
+	unsigned int	cmu_aclkstop_coreblk_sys_pwr_reg;
+	unsigned int	cmu_sclkstop_coreblk_sys_pwr_reg;
+	unsigned char	res23[0x4];
+	unsigned int	cmu_reset_coreblk_sys_pwr_reg;
+	unsigned int	dram_freq_down_sys_pwr_reg;
+	unsigned int	ddrphy_dlloff_sys_pwr_reg;
+	unsigned int	ddrphy_dlllock_sys_pwr_reg;
+	unsigned char	res25[0x4];
+	unsigned int	apll_sysclk_sys_pwr_reg;
+	unsigned int	mpll_sysclk_sys_pwr_reg;
+	unsigned int	vpll_sysclk_sys_pwr_reg;
+	unsigned int	epll_sysclk_sys_pwr_reg;
+	unsigned int	bpll_sysclk_sys_pwr_reg;
+	unsigned int	cpll_sysclk_sys_pwr_reg;
+	unsigned int	dpll_sysclk_sys_pwr_reg;
+	unsigned int	ipll_sysclk_sys_pwr_reg;
+	unsigned int	kpll_sysclk_sys_pwr_reg;
+	unsigned int	mplluser_sysclk_sys_pwr_reg;
+	unsigned char	res512[0x8];
+	unsigned int	bplluser_sysclk_sys_pwr_reg;
+	unsigned int	rpll_sysclk_sys_pwr_reg;
+	unsigned int	spll_sysclk_sys_pwr_reg;
+	unsigned char	res26[0x4];
+	unsigned int	top_bus_sys_pwr_reg;
+	unsigned int	top_retention_sys_pwr_reg;
+	unsigned int	top_pwr_sys_pwr_reg;
+	unsigned char	res29[0x4];
+	unsigned int	top_bus_coreblk_sys_pwr_reg;
+	unsigned int	top_retention_coreblk_sys_pwr_reg;
+	unsigned int	top_pwr_coreblk_sys_pwr_reg;
+	unsigned char	res30[0x4];
+	unsigned int	logic_reset_sys_pwr_reg;
+	unsigned int	oscclk_gate_sys_pwr_reg;
+	unsigned char	res31[0x8];
+	unsigned int	logic_reset_coreblk_sys_pwr_reg;
+	unsigned int	oscclk_gate_coreblk_sys_pwr_reg;
+	unsigned int	intram_mem_sys_pwr_reg;
+	unsigned int	introm_mem_sys_pwr_reg;
+	unsigned char	res32[0x44];
+	unsigned int	pad_retention_mau_sys_pwr_reg;
+	unsigned int	pad_retention_jtag_sys_pwr_reg;
+	unsigned char	res36[0x4];
+	unsigned int	pad_retention_dram_sys_pwr_reg;
+	unsigned int	pad_retention_uart_sys_pwr_reg;
+	unsigned int	pad_retention_mmca_sys_pwr_reg;
+	unsigned int	pad_retention_mmcb_sys_pwr_reg;
+	unsigned int	pad_retention_mmcc_sys_pwr_reg;
+	unsigned int	pad_retention_hsi_sys_pwr_reg;
+	unsigned int	pad_retention_ebia_sys_pwr_reg;
+	unsigned int	pad_retention_ebib_sys_pwr_reg;
+	unsigned int	pad_retention_spi_sys_pwr_reg;
+	unsigned int	pad_retention_dram_coreblk_sys_pwr_reg;
+	unsigned char	res28[0x8];
+	unsigned int	pad_isolation_sys_pwr_reg;
+	unsigned char	res37[0xc];
+	unsigned int	pad_isolation_coreblk_sys_pwr_reg;
+	unsigned char	res38[0xc];
+	unsigned int	pad_alv_sel_sys_pwr_reg;
+	unsigned char	res39[0x1c];
+	unsigned int	xusbxti_sys_pwr_reg;
+	unsigned int	xxti_sys_pwr_reg;
+	unsigned char	res40[0x38];
+	unsigned int	ext_regulator_sys_pwr_reg;
+	unsigned char	res41[0x3c];
+	unsigned int	gpio_mode_sys_pwr_reg;
+	unsigned char	res42[0x1c];
+	unsigned int	gpio_mode_coreblk_sys_pwr_reg;
+	unsigned char	res43[0x1c];
+	unsigned int	gpio_mode_mau_sys_pwr_reg;
+	unsigned int	top_asb_reset_sys_pwr_reg;
+	unsigned int	top_asb_isolation_sys_pwr_reg;
+	unsigned char	res44[0xb4];
+	unsigned int	gscl_sys_pwr_reg;
+	unsigned int	isp_sys_pwr_reg;
+	unsigned int	mfc_sys_pwr_reg;
+	unsigned int	g3d_sys_pwr_reg;
+	unsigned int	disp1_sys_pwr_reg;
+	unsigned int	mau_sys_pwr_reg;
+	unsigned int	g2d_sys_pwr_reg;
+	unsigned int	msc_sys_pwr_reg;
+	unsigned int	fsys_sys_pwr_reg;
+	unsigned int	fsys2_sys_pwr_reg;
+	unsigned int	psgen_sys_pwr_reg;
+	unsigned int	peric_sys_pwr_reg;
+	unsigned int	wcore_sys_pwr_reg;
+	unsigned char	res46[0x4c];
+	unsigned int	cmu_clkstop_gscl_sys_pwr_reg;
+	unsigned int	cmu_clkstop_isp_sys_pwr_reg;
+	unsigned int	cmu_clkstop_mfc_sys_pwr_reg;
+	unsigned int	cmu_clkstop_g3d_sys_pwr_reg;
+	unsigned int	cmu_clkstop_disp1_sys_pwr_reg;
+	unsigned int	cmu_clkstop_mau_sys_pwr_reg;
+	unsigned int	cmu_clkstop_g2d_sys_pwr_reg;
+	unsigned int	cmu_clkstop_msc_sys_pwr_reg;
+	unsigned int	cmu_clkstop_fsys_sys_pwr_reg;
+	unsigned int	cmu_clkstop_fsys2_sys_pwr_reg;
+	unsigned int	cmu_clkstop_psgen_sys_pwr_reg;
+	unsigned int	cmu_clkstop_peric_sys_pwr_reg;
+	unsigned int	cmu_clkstop_wcore_sys_pwr_reg;
+	unsigned char	res48[0x8];
+	unsigned int	cmu_sysclk_toppwr_sys_pwr_reg;
+	unsigned int	cmu_sysclk_gscl_sys_pwr_reg;
+	unsigned int	cmu_sysclk_isp_sys_pwr_reg;
+	unsigned int	cmu_sysclk_mfc_sys_pwr_reg;
+	unsigned int	cmu_sysclk_g3d_sys_pwr_reg;
+	unsigned int	cmu_sysclk_disp1_sys_pwr_reg;
+	unsigned int	cmu_sysclk_mau_sys_pwr_reg;
+	unsigned int	cmu_sysclk_g2d_sys_pwr_reg;
+	unsigned int	cmu_sysclk_msc_sys_pwr_reg;
+	unsigned int	cmu_sysclk_fsys_sys_pwr_reg;
+	unsigned int	cmu_sysclk_fsys2_sys_pwr_reg;
+	unsigned int	cmu_sysclk_psgen_sys_pwr_reg;
+	unsigned int	cmu_sysclk_peric_sys_pwr_reg;
+	unsigned int	cmu_sysclk_wcore_sys_pwr_reg;
+	unsigned int	cmu_sysclk_coreblk_toppwr_sys_pwr_reg;
+	unsigned char	res50[0x78];
+	unsigned int	cmu_reset_fsys2_sys_pwr_reg;
+	unsigned int	cmu_reset_psgen_sys_pwr_reg;
+	unsigned int	cmu_reset_peric_sys_pwr_reg;
+	unsigned int	cmu_reset_wcore_sys_pwr_reg;
+	unsigned int	cmu_reset_gscl_sys_pwr_reg;
+	unsigned int	cmu_reset_isp_sys_pwr_reg;
+	unsigned int	cmu_reset_mfc_sys_pwr_reg;
+	unsigned int	cmu_reset_g3d_sys_pwr_reg;
+	unsigned int	cmu_reset_disp1_sys_pwr_reg;
+	unsigned int	cmu_reset_mau_sys_pwr_reg;
+	unsigned int	cmu_reset_g2d_sys_pwr_reg;
+	unsigned int	cmu_reset_msc_sys_pwr_reg;
+	unsigned int	cmu_reset_fsys_sys_pwr_reg;
+	unsigned char	res52[0xa5c];
+	unsigned int	arm_core0_configuration;
+	unsigned int	arm_core0_status;
+	unsigned int	arm_core0_option;
+	unsigned char	res53[0x14];
+	unsigned int	dis_irq_arm_core0_local_configuration;
+	unsigned int	dis_irq_arm_core0_local_status;
+	unsigned int	dis_irq_arm_core0_local_option;
+	unsigned char	res54[0x14];
+	unsigned int	dis_irq_arm_core0_central_configuration;
+	unsigned int	dis_irq_arm_core0_central_status;
+	unsigned int	dis_irq_arm_core0_central_option;
+	unsigned char	res55[0x34];
+	unsigned int	arm_core1_configuration;
+	unsigned int	arm_core1_status;
+	unsigned int	arm_core1_option;
+	unsigned char	res56[0x14];
+	unsigned int	dis_irq_arm_core1_local_configuration;
+	unsigned int	dis_irq_arm_core1_local_status;
+	unsigned int	dis_irq_arm_core1_local_option;
+	unsigned char	res57[0x14];
+	unsigned int	dis_irq_arm_core1_central_configuration;
+	unsigned int	dis_irq_arm_core1_central_status;
+	unsigned int	dis_irq_arm_core1_central_option;
+	unsigned char	res600[0x34];
+	unsigned int	arm_core2_configuration;
+	unsigned int	arm_core2_status;
+	unsigned int	arm_core2_option;
+	unsigned char	res601[0x14];
+	unsigned int	dis_irq_arm_core2_local_configuration;
+	unsigned int	dis_irq_arm_core2_local_status;
+	unsigned int	dis_irq_arm_core2_local_option;
+	unsigned char	res602[0x14];
+	unsigned int	dis_irq_arm_core2_central_configuration;
+	unsigned int	dis_irq_arm_core2_central_status;
+	unsigned int	dis_irq_arm_core2_central_option;
+	unsigned char	res603[0x34];
+	unsigned int	arm_core3_configuration;
+	unsigned int	arm_core3_status;
+	unsigned int	arm_core3_option;
+	unsigned char	res900[0x14];
+	unsigned int	dis_irq_arm_core3_local_configuration;
+	unsigned int	dis_irq_arm_core3_local_status;
+	unsigned int	dis_irq_arm_core3_local_option;
+	unsigned char	res901[0x14];
+	unsigned int	dis_irq_arm_core3_central_configuration;
+	unsigned int	dis_irq_arm_core3_central_status;
+	unsigned int	dis_irq_arm_core3_central_option;
+	unsigned char	res604[0x34];
+	unsigned int	kfc_core0_configuration;
+	unsigned int	kfc_core0_status;
+	unsigned int	kfc_core0_option;
+	unsigned char	res605[0x14];
+	unsigned int	dis_irq_kfc_core0_local_configuration;
+	unsigned int	dis_irq_kfc_core0_local_status;
+	unsigned int	dis_irq_kfc_core0_local_option;
+	unsigned char	res606[0x14];
+	unsigned int	dis_irq_kfc_core0_central_configuration;
+	unsigned int	dis_irq_kfc_core0_central_status;
+	unsigned int	dis_irq_kfc_core0_central_option;
+	unsigned char	res607[0x34];
+	unsigned int	kfc_core1_configuration;
+	unsigned int	kfc_core1_status;
+	unsigned int	kfc_core1_option;
+	unsigned char	res608[0x14];
+	unsigned int	dis_irq_kfc_core1_local_configuration;
+	unsigned int	dis_irq_kfc_core1_local_status;
+	unsigned int	dis_irq_kfc_core1_local_option;
+	unsigned char	res609[0x14];
+	unsigned int	dis_irq_kfc_core1_central_configuration;
+	unsigned int	dis_irq_kfc_core1_central_status;
+	unsigned int	dis_irq_kfc_core1_central_option;
+	unsigned char	res610[0x34];
+	unsigned int	kfc_core2_configuration;
+	unsigned int	kfc_core2_status;
+	unsigned int	kfc_core2_option;
+	unsigned char	res611[0x14];
+	unsigned int	dis_irq_kfc_core2_local_configuration;
+	unsigned int	dis_irq_kfc_core2_local_status;
+	unsigned int	dis_irq_kfc_core2_local_option;
+	unsigned char	res612[0x14];
+	unsigned int	dis_irq_kfc_core2_central_configuration;
+	unsigned int	dis_irq_kfc_core2_central_status;
+	unsigned int	dis_irq_kfc_core2_central_option;
+	unsigned char	res613[0x34];
+	unsigned int	kfc_core3_configuration;
+	unsigned int	kfc_core3_status;
+	unsigned int	kfc_core3_option;
+	unsigned char	res614[0x14];
+	unsigned int	dis_irq_kfc_core3_local_configuration;
+	unsigned int	dis_irq_kfc_core3_local_status;
+	unsigned int	dis_irq_kfc_core3_local_option;
+	unsigned char	res615[0x14];
+	unsigned int	dis_irq_kfc_core3_central_configuration;
+	unsigned int	dis_irq_kfc_core3_central_status;
+	unsigned int	dis_irq_kfc_core3_central_option;
+	unsigned char	res61[0xb4];
+	unsigned int	isp_arm_configuration;
+	unsigned int	isp_arm_status;
+	unsigned int	isp_arm_option;
+	unsigned char	res62[0x14];
+	unsigned int	dis_irq_isp_arm_local_configuration;
+	unsigned int	dis_irq_isp_arm_local_status;
+	unsigned int	dis_irq_isp_arm_local_option;
+	unsigned char	res63[0x14];
+	unsigned int	dis_irq_isp_arm_central_configuration;
+	unsigned int	dis_irq_isp_arm_central_status;
+	unsigned int	dis_irq_isp_arm_central_option;
+	unsigned char	res64[0x34];
+	unsigned int	arm_common_configuration;
+	unsigned int	arm_common_status;
+	unsigned int	arm_common_option;
+	unsigned char	res616[0x74];
+	unsigned int	kfc_common_configuration;
+	unsigned int	kfc_common_status;
+	unsigned int	kfc_common_option;
+	unsigned char	res65[0x74];
+	unsigned int	arm_l2_configuration;
+	unsigned int	arm_l2_status;
+	unsigned int	arm_l2_option;
+	unsigned char	res617[0x74];
+	unsigned int	kfc_l2_configuration;
+	unsigned int	kfc_l2_status;
+	unsigned int	kfc_l2_option;
+	unsigned char	res66[0x74];
+	unsigned int	cmu_cpu_aclkstop_configuration;
+	unsigned int	cmu_cpu_aclkstop_status;
+	unsigned int	cmu_cpu_aclkstop_option;
+	unsigned char	res67[0x14];
+	unsigned int	cmu_cpu_sclkstop_configuration;
+	unsigned int	cmu_cpu_sclkstop_status;
+	unsigned int	cmu_cpu_sclkstop_option;
+	unsigned char	res618[0x4];
+	unsigned int	cmu_kfc_aclkstop_configuration;
+	unsigned int	cmu_kfc_aclkstop_status;
+	unsigned int	cmu_kfc_aclkstop_option;
+	unsigned char	res619[0xc4];
+	unsigned int	cmu_aclkstop_configuration;
+	unsigned int	cmu_aclkstop_status;
+	unsigned int	cmu_aclkstop_option;
+	unsigned char	res620[0x14];
+	unsigned int	cmu_sclkstop_configuration;
+	unsigned int	cmu_sclkstop_status;
+	unsigned int	cmu_sclkstop_option;
+	unsigned char	res68[0x34];
+	unsigned int	cmu_reset_configuration;
+	unsigned int	cmu_reset_status;
+	unsigned int	cmu_reset_option;
+	unsigned char	res69[0x94];
+	unsigned int	cmu_aclkstop_coreblk_configuration;
+	unsigned int	cmu_aclkstop_coreblk_status;
+	unsigned int	cmu_aclkstop_coreblk_option;
+	unsigned char	res70[0x14];
+	unsigned int	cmu_sclkstop_coreblk_configuration;
+	unsigned int	cmu_sclkstop_coreblk_status;
+	unsigned int	cmu_sclkstop_coreblk_option;
+	unsigned char	res71[0x34];
+	unsigned int	cmu_reset_coreblk_configuration;
+	unsigned int	cmu_reset_coreblk_status;
+	unsigned int	cmu_reset_coreblk_option;
+	unsigned char	res621[0x14];
+	unsigned int	dram_freq_down_configuration;
+	unsigned int	dram_freq_down_status;
+	unsigned int	dram_freq_down_option;
+	unsigned char	res622[0x14];
+	unsigned int	ddrphy_dlloff_configuration;
+	unsigned int	ddrphy_dlloff_status;
+	unsigned int	ddrphy_dlloff_option;
+	unsigned char	res72[0x14];
+	unsigned int	ddrphy_dlllock_configuration;
+	unsigned int	ddrphy_dlllock_status;
+	unsigned int	ddrphy_dlllock_option;
+	unsigned char	res73[0x34];
+	unsigned int	apll_sysclk_configuration;
+	unsigned int	apll_sysclk_status;
+	unsigned int	apll_sysclk_option;
+	unsigned char	res74[0x18];
+	unsigned int	mpll_sysclk_status;
+	unsigned int	mpll_sysclk_option;
+	unsigned char	res75[0x14];
+	unsigned int	vpll_sysclk_configuration;
+	unsigned int	vpll_sysclk_status;
+	unsigned int	vpll_sysclk_option;
+	unsigned char	res76[0x14];
+	unsigned int	epll_sysclk_configuration;
+	unsigned int	epll_sysclk_status;
+	unsigned int	epll_sysclk_option;
+	unsigned char	res77[0x14];
+	unsigned int	bpll_sysclk_configuration;
+	unsigned int	bpll_sysclk_status;
+	unsigned int	bpll_sysclk_option;
+	unsigned char	res78[0x14];
+	unsigned int	cpll_sysclk_configuration;
+	unsigned int	cpll_sysclk_status;
+	unsigned int	cpll_sysclk_option;
+	unsigned char	res79[0x14];
+	unsigned int	dpll_sysclk_configuration;
+	unsigned int	dpll_sysclk_status;
+	unsigned int	dpll_sysclk_option;
+	unsigned char	res700[0x14];
+	unsigned int	ipll_sysclk_configuration;
+	unsigned int	ipll_sysclk_status;
+	unsigned int	ipll_sysclk_option;
+	unsigned char	res903[0x14];
+	unsigned int	kpll_sysclk_configuration;
+	unsigned int	kpll_sysclk_status;
+	unsigned int	kpll_sysclk_option;
+	unsigned char	res80[0x14];
+	unsigned int	mplluser_sysclk_configuration;
+	unsigned int	mplluser_sysclk_status;
+	unsigned int	mplluser_sysclk_option;
+	unsigned char	res81[0x54];
+	unsigned int	bplluser_sysclk_configuration;
+	unsigned int	bplluser_sysclk_status;
+	unsigned int	bplluser_sysclk_option;
+	unsigned char	res701[0x14];
+	unsigned int	rplluser_sysclk_configuration;
+	unsigned int	rplluser_sysclk_status;
+	unsigned int	rplluser_sysclk_option;
+	unsigned char	res702[0x14];
+	unsigned int	splluser_sysclk_configuration;
+	unsigned int	splluser_sysclk_status;
+	unsigned int	splluser_sysclk_option;
+	unsigned char	res82[0x34];
+	unsigned int	top_bus_configuration;
+	unsigned int	top_bus_status;
+	unsigned int	top_bus_option;
+	unsigned char	res83[0x14];
+	unsigned int	top_retention_configuration;
+	unsigned int	top_retention_status;
+	unsigned int	top_retention_option;
+	unsigned char	res84[0x14];
+	unsigned int	top_pwr_configuration;
+	unsigned int	top_pwr_status;
+	unsigned int	top_pwr_option;
+	unsigned char	res85[0x34];
+	unsigned int	top_bus_coreblk_configuration;
+	unsigned int	top_bus_coreblk_status;
+	unsigned int	top_bus_coreblk_option;
+	unsigned char	res86[0x14];
+	unsigned int	top_retention_coreblk_configuration;
+	unsigned int	top_retention_coreblk_status;
+	unsigned int	top_retention_coreblk_option;
+	unsigned char	res87[0x14];
+	unsigned int	top_pwr_coreblk_configuration;
+	unsigned int	top_pwr_coreblk_status;
+	unsigned int	top_pwr_coreblk_option;
+	unsigned char	res88[0x34];
+	unsigned int	logic_reset_configuration;
+	unsigned int	logic_reset_status;
+	unsigned int	logic_reset_option;
+	unsigned char	res89[0x14];
+	unsigned int	oscclk_gate_configuration;
+	unsigned int	oscclk_gate_status;
+	unsigned int	oscclk_gate_option;
+	unsigned char	res90[0x54];
+	unsigned int	logic_reset_coreblk_configuration;
+	unsigned int	logic_reset_coreblk_status;
+	unsigned int	logic_reset_coreblk_option;
+	unsigned char	res91[0x14];
+	unsigned int	oscclk_gate_coreblk_configuration;
+	unsigned int	oscclk_gate_coreblk_status;
+	unsigned int	oscclk_gate_coreblk_option;
+	unsigned char	res99[0x174];
+	unsigned int	intram_mem_configuration;
+	unsigned int	intram_mem_status;
+	unsigned int	intram_mem_option;
+	unsigned char	res100[0x14];
+	unsigned int	introm_mem_configuration;
+	unsigned int	introm_mem_status;
+	unsigned int	introm_mem_option;
+	unsigned char	res101[0xb4];
+	unsigned int	pad_retention_dram_configuration;
+	unsigned int	pad_retention_dram_status;
+	unsigned int	pad_retention_dram_option;
+	unsigned char	res106[0x14];
+	unsigned int	pad_retention_mau_configuration;
+	unsigned int	pad_retention_mau_status;
+	unsigned int	pad_retention_mau_option;
+	unsigned char	res107[0x14];
+	unsigned int	pad_retention_jtag_configuration;
+	unsigned int	pad_retention_jtag_status;
+	unsigned int	pad_retention_jtag_option;
+	unsigned char	res92[0x74];
+	unsigned int	pad_retention_dram_configuration_2;
+	unsigned int	pad_retention_dram_status_2;
+	unsigned int	pad_retention_dram_option_2;
+	unsigned char	res111[0x14];
+	unsigned int	pad_retention_uart_configuration;
+	unsigned int	pad_retention_uart_status;
+	unsigned int	pad_retention_uart_option;
+	unsigned char	res112[0x14];
+	unsigned int	pad_retention_mmca_configuration;
+	unsigned int	pad_retention_mmca_status;
+	unsigned int	pad_retention_mmca_option;
+	unsigned char	res113[0x14];
+	unsigned int	pad_retention_mmcb_configuration;
+	unsigned int	pad_retention_mmcb_status;
+	unsigned int	pad_retention_mmcb_option;
+	unsigned char	res93[0x14];
+	unsigned int	pad_retention_mmcc_configuration;
+	unsigned int	pad_retention_mmcc_status;
+	unsigned int	pad_retention_mmcc_option;
+	unsigned char	res94[0x14];
+	unsigned int	pad_retention_hsi_configuration;
+	unsigned int	pad_retention_hsi_status;
+	unsigned int	pad_retention_hsi_option;
+	unsigned char	res114[0x14];
+	unsigned int	pad_retention_ebia_configuration;
+	unsigned int	pad_retention_ebia_status;
+	unsigned int	pad_retention_ebia_option;
+	unsigned char	res115[0x14];
+	unsigned int	pad_retention_ebib_configuration;
+	unsigned int	pad_retention_ebib_status;
+	unsigned int	pad_retention_ebib_option;
+	unsigned char	res116[0x14];
+	unsigned int	pad_retention_spi_configuration;
+	unsigned int	pad_retention_spi_status;
+	unsigned int	pad_retention_spi_option;
+	unsigned char	res117[0x14];
+	unsigned int	pad_retention_dram_coreblk_configuration;
+	unsigned int	pad_retention_dram_coreblk_status;
+	unsigned int	pad_retention_dram_coreblk_option;
+	unsigned char	res118[0x14];
+	unsigned int	pad_isolation_configuration;
+	unsigned int	pad_isolation_status;
+	unsigned int	pad_isolation_option;
+	unsigned char	res119[0x74];
+	unsigned int	pad_isolation_coreblk_configuration;
+	unsigned int	pad_isolation_coreblk_status;
+	unsigned int	pad_isolation_coreblk_option;
+	unsigned char	res120[0x74];
+	unsigned int	pad_alv_sel_configuration;
+	unsigned int	pad_alv_sel_status;
+	unsigned int	pad_alv_sel_option0;
+	unsigned int	ps_hold_control;
+	unsigned char	res130[0xf0];
+	unsigned int	xusbxti_configuration;
+	unsigned int	xusbxti_status;
+	unsigned int	xusbxti_option;
+	unsigned char	res910[0x10];
+	unsigned int	xusbxti_duration3;
+	unsigned int	xxti_configuration;
+	unsigned int	xxti_status;
+	unsigned int	xxti_option;
+	unsigned char	res131[0x10];
+	unsigned int	xxti_duration3;
+	unsigned char	res132[0x1c0];
+	unsigned int	ext_regulator_configuration;
+	unsigned int	ext_regulator_status;
+	unsigned int	ext_regulator_option;
+	unsigned char	res133[0x10];
+	unsigned int	ext_regulator_duration3;
+	unsigned char	res134[0x1e0];
+	unsigned int	gpio_mode_configuration;
+	unsigned int	gpio_mode_status;
+	unsigned int	gpio_mode_option;
+	unsigned char	res135[0xf4];
+	unsigned int	gpio_mode_coreblk_configuration;
+	unsigned int	gpio_mode_coreblk_status;
+	unsigned int	gpio_mode_coreblk_option;
+	unsigned char	res136[0xd4];
+	unsigned int	gpio_mode_mau_configuration;
+	unsigned int	gpio_mode_mau_status;
+	unsigned int	gpio_mode_mau_option;
+	unsigned char	res137[0x14];
+	unsigned int	top_asb_reset_configuration;
+	unsigned int	top_asb_reset_status;
+	unsigned int	top_asb_reset_option;
+	unsigned char	res138[0x14];
+	unsigned int	top_asb_isolation_configuration;
+	unsigned int	top_asb_isolation_status;
+	unsigned int	top_asb_isolation_option;
+	unsigned char	res139[0x5d4];
+	unsigned int	gscl_configuration;
+	unsigned int	gscl_status;
+	unsigned int	gscl_option;
+	unsigned char	res140[0x14];
+	unsigned int	isp_configuration;
+	unsigned int	isp_status;
+	unsigned int	isp_option;
+	unsigned char	res141[0x34];
+	unsigned int	mfc_configuration;
+	unsigned int	mfc_status;
+	unsigned int	mfc_option;
+	unsigned char	res142[0x14];
+	unsigned int	g3d_configuration;
+	unsigned int	g3d_status;
+	unsigned int	g3d_option;
+	unsigned char	res143[0x34];
+	unsigned int	disp1_configuration;
+	unsigned int	disp1_status;
+	unsigned int	disp1_option;
+	unsigned char	res144[0x14];
+	unsigned int	mau_configuration;
+	unsigned int	mau_status;
+	unsigned int	mau_option;
+	unsigned char	res800[0x14];
+	unsigned int	g2d_configuration;
+	unsigned int	g2d_status;
+	unsigned int	g2d_option;
+	unsigned char	res801[0x14];
+	unsigned int	msc_configuration;
+	unsigned int	msc_status;
+	unsigned int	msc_option;
+	unsigned char	res802[0x14];
+	unsigned int	fsys_configuration;
+	unsigned int	fsys_status;
+	unsigned int	fsys_option;
+	unsigned char	res803[0x14];
+	unsigned int	fsys2_configuration;
+	unsigned int	fsys2_status;
+	unsigned int	fsys2_option;
+	unsigned char	res804[0x14];
+	unsigned int	psgen_configuration;
+	unsigned int	psgen_status;
+	unsigned int	psgen_option;
+	unsigned char	res805[0x14];
+	unsigned int	peric_configuration;
+	unsigned int	peric_status;
+	unsigned int	peric_option;
+	unsigned char	res806[0x14];
+	unsigned int	wcore_configuration;
+	unsigned int	wcore_status;
+	unsigned int	wcore_option;
+	unsigned char	res145[0x234];
+	unsigned int	cmu_clkstop_gscl_configuration;
+	unsigned int	cmu_clkstop_gscl_status;
+	unsigned int	cmu_clkstop_gscl_option;
+	unsigned char	res146[0x14];
+	unsigned int	cmu_clkstop_isp_configuration;
+	unsigned int	cmu_clkstop_isp_status;
+	unsigned int	cmu_clkstop_isp_option;
+	unsigned char	res147[0x34];
+	unsigned int	cmu_clkstop_mfc_configuration;
+	unsigned int	cmu_clkstop_mfc_status;
+	unsigned int	cmu_clkstop_mfc_option;
+	unsigned char	res148[0x14];
+	unsigned int	cmu_clkstop_g3d_configuration;
+	unsigned int	cmu_clkstop_g3d_status;
+	unsigned int	cmu_clkstop_g3d_option;
+	unsigned char	res149[0x34];
+	unsigned int	cmu_clkstop_disp1_configuration;
+	unsigned int	cmu_clkstop_disp1_status;
+	unsigned int	cmu_clkstop_disp1_option;
+	unsigned char	res150[0x14];
+	unsigned int	cmu_clkstop_mau_configuration;
+	unsigned int	cmu_clkstop_mau_status;
+	unsigned int	cmu_clkstop_mau_option;
+	unsigned char	res807[0x14];
+	unsigned int	cmu_clkstop_g2d_configuration;
+	unsigned int	cmu_clkstop_g2d_status;
+	unsigned int	cmu_clkstop_g2d_option;
+	unsigned char	res808[0x14];
+	unsigned int	cmu_clkstop_msc_configuration;
+	unsigned int	cmu_clkstop_msc_status;
+	unsigned int	cmu_clkstop_msc_option;
+	unsigned char	res809[0x14];
+	unsigned int	cmu_clkstop_fsys_configuration;
+	unsigned int	cmu_clkstop_fsys_status;
+	unsigned int	cmu_clkstop_fsys_option;
+	unsigned char	res810[0x14];
+	unsigned int	cmu_clkstop_fsys2_configuration;
+	unsigned int	cmu_clkstop_fsys2_status;
+	unsigned int	cmu_clkstop_fsys2_option;
+	unsigned char	res811[0x14];
+	unsigned int	cmu_clkstop_psgen_configuration;
+	unsigned int	cmu_clkstop_psgen_status;
+	unsigned int	cmu_clkstop_psgen_option;
+	unsigned char	res812[0x14];
+	unsigned int	cmu_clkstop_peric_configuration;
+	unsigned int	cmu_clkstop_peric_status;
+	unsigned int	cmu_clkstop_peric_option;
+	unsigned char	res813[0x14];
+	unsigned int	cmu_clkstop_wcore_configuration;
+	unsigned int	cmu_clkstop_wcore_status;
+	unsigned int	cmu_clkstop_wcore_option;
+	unsigned char	res151[0x14];
+	unsigned int	cmu_sysclk_toppwr_configuration;
+	unsigned int	cmu_sysclk_toppwr_status;
+	unsigned int	cmu_sysclk_toppwr_option;
+	unsigned char	res920[0x18];
+	unsigned int	cmu_sysclk_gscl_status;
+	unsigned int	cmu_sysclk_gscl_option;
+	unsigned char	res152[0x18];
+	unsigned int	cmu_sysclk_isp_status;
+	unsigned int	cmu_sysclk_isp_option;
+	unsigned char	res153[0x38];
+	unsigned int	cmu_sysclk_mfc_status;
+	unsigned int	cmu_sysclk_mfc_option;
+	unsigned char	res154[0x18];
+	unsigned int	cmu_sysclk_g3d_status;
+	unsigned int	cmu_sysclk_g3d_option;
+	unsigned char	res155[0x38];
+	unsigned int	cmu_sysclk_disp1_status;
+	unsigned int	cmu_sysclk_disp1_option;
+	unsigned char	res156[0x18];
+	unsigned int	cmu_sysclk_mau_status;
+	unsigned int	cmu_sysclk_mau_option;
+	unsigned char	res814[0x18];
+	unsigned int	cmu_sysclk_g2d_status;
+	unsigned int	cmu_sysclk_g2d_option;
+	unsigned char	res815[0x18];
+	unsigned int	cmu_sysclk_msc_status;
+	unsigned int	cmu_sysclk_msc_option;
+	unsigned char	res922[0x18];
+	unsigned int	cmu_sysclk_fsys_status;
+	unsigned int	cmu_sysclk_fsys_option;
+	unsigned char	res816[0x18];
+	unsigned int	cmu_sysclk_fsys2_status;
+	unsigned int	cmu_sysclk_fsys2_option;
+	unsigned char	res817[0x18];
+	unsigned int	cmu_sysclk_psgen_status;
+	unsigned int	cmu_sysclk_psgen_option;
+	unsigned char	res950[0x18];
+	unsigned int	cmu_sysclk_peric_status;
+	unsigned int	cmu_sysclk_peric_option;
+	unsigned char	res818[0x18];
+	unsigned int	cmu_sysclk_wcore_status;
+	unsigned int	cmu_sysclk_wcore_option;
+	unsigned char	res819[0x18];
+	unsigned int	cmu_sysclk_coreblk_toppwr_status;
+	unsigned int	cmu_sysclk_coreblk_toppwr_option;
+	unsigned char	res157[0x414];
+	unsigned int	cmu_reset_gscl_configuration;
+	unsigned int	cmu_reset_gscl_status;
+	unsigned int	cmu_reset_gscl_option;
+	unsigned char	res158[0x14];
+	unsigned int	cmu_reset_isp_configuration;
+	unsigned int	cmu_reset_isp_status;
+	unsigned int	cmu_reset_isp_option;
+	unsigned char	res159[0x34];
+	unsigned int	cmu_reset_mfc_configuration;
+	unsigned int	cmu_reset_mfc_status;
+	unsigned int	cmu_reset_mfc_option;
+	unsigned char	res160[0x14];
+	unsigned int	cmu_reset_g3d_configuration;
+	unsigned int	cmu_reset_g3d_status;
+	unsigned int	cmu_reset_g3d_option;
+	unsigned char	res161[0x34];
+	unsigned int	cmu_reset_disp1_configuration;
+	unsigned int	cmu_reset_disp1_status;
+	unsigned int	cmu_reset_disp1_option;
+	unsigned char	res162[0x14];
+	unsigned int	cmu_reset_mau_configuration;
+	unsigned int	cmu_reset_mau_status;
+	unsigned int	cmu_reset_mau_option;
+	unsigned char	res163[0x14];
+	unsigned int	version_info;
+	unsigned int	i2s_bypass;
+	unsigned int	kfc_swreset_mask_from_eagle;
+	unsigned char	res164[0xf4];
+	unsigned int	cmu_reset_g2d_configuration;
+	unsigned int	cmu_reset_g2d_status;
+	unsigned int	cmu_reset_g2d_option;
+	unsigned char	res165[0x14];
+	unsigned int	cmu_reset_msc_configuration;
+	unsigned int	cmu_reset_msc_status;
+	unsigned int	cmu_reset_msc_option;
+	unsigned char	res166[0x14];
+	unsigned int	cmu_reset_fsys_configuration;
+	unsigned int	cmu_reset_fsys_status;
+	unsigned int	cmu_reset_fsys_option;
+	unsigned char	res167[0x14];
+	unsigned int	cmu_reset_fsys2_configuration;
+	unsigned int	cmu_reset_fsys2_status;
+	unsigned int	cmu_reset_fsys2_option;
+	unsigned char	res168[0x14];
+	unsigned int	cmu_reset_psgen_configuration;
+	unsigned int	cmu_reset_psgen_status;
+	unsigned int	cmu_reset_psgen_option;
+	unsigned char	res169[0x14];
+	unsigned int	cmu_reset_peric_configuration;
+	unsigned int	cmu_reset_peric_status;
+	unsigned int	cmu_reset_peric_option;
+	unsigned char	res170[0x14];
+	unsigned int	cmu_reset_wcore_configuration;
+	unsigned int	cmu_reset_wcore_status;
+	unsigned int	cmu_reset_wcore_option;
+};
 #endif	/* __ASSEMBLY__ */
 
 void set_mipi_phy_ctrl(unsigned int dev_index, unsigned int enable);
Signature · 1 line
1.7.12.4
#5 lore raw

PATCH v12 4/11 EXYNOS5420: Add dmc and phy_control register structure

In reply to Rajeshwari S Shinde

Add dmc and phy_control register structure for 5420.

---
Changes in V10:
- New patch
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/include/asm/arch-exynos/dmc.h | 167 +++++++++++++++++++++++++++++++++
 1 file changed, 167 insertions(+)
arch/arm/include/asm/arch-exynos/dmc.h +167 -0
index f65c676..32ad3ae 100644
@@ -205,6 +205,127 @@ struct exynos5_dmc {
 	unsigned int pmcnt3_ppc_a;
 };
 
+struct exynos5420_dmc {
+	unsigned int concontrol;
+	unsigned int memcontrol;
+	unsigned int cgcontrol;
+	unsigned char res500[0x4];
+	unsigned int directcmd;
+	unsigned int prechconfig0;
+	unsigned int phycontrol0;
+	unsigned int prechconfig1;
+	unsigned char res1[0x8];
+	unsigned int pwrdnconfig;
+	unsigned int timingpzq;
+	unsigned int timingref;
+	unsigned int timingrow0;
+	unsigned int timingdata0;
+	unsigned int timingpower0;
+	unsigned int phystatus;
+	unsigned int etctiming;
+	unsigned int chipstatus;
+	unsigned char res3[0x8];
+	unsigned int mrstatus;
+	unsigned char res4[0x8];
+	unsigned int qoscontrol0;
+	unsigned char resr5[0x4];
+	unsigned int qoscontrol1;
+	unsigned char res6[0x4];
+	unsigned int qoscontrol2;
+	unsigned char res7[0x4];
+	unsigned int qoscontrol3;
+	unsigned char res8[0x4];
+	unsigned int qoscontrol4;
+	unsigned char res9[0x4];
+	unsigned int qoscontrol5;
+	unsigned char res10[0x4];
+	unsigned int qoscontrol6;
+	unsigned char res11[0x4];
+	unsigned int qoscontrol7;
+	unsigned char res12[0x4];
+	unsigned int qoscontrol8;
+	unsigned char res13[0x4];
+	unsigned int qoscontrol9;
+	unsigned char res14[0x4];
+	unsigned int qoscontrol10;
+	unsigned char res15[0x4];
+	unsigned int qoscontrol11;
+	unsigned char res16[0x4];
+	unsigned int qoscontrol12;
+	unsigned char res17[0x4];
+	unsigned int qoscontrol13;
+	unsigned char res18[0x4];
+	unsigned int qoscontrol14;
+	unsigned char res19[0x4];
+	unsigned int qoscontrol15;
+	unsigned char res20[0x4];
+	unsigned int timing_set_sw;
+	unsigned int timingrow1;
+	unsigned int timingdata1;
+	unsigned int timingpower1;
+	unsigned char res300[0x4];
+	unsigned int wrtra_config;
+	unsigned int rdlvl_config;
+	unsigned char res21[0x4];
+	unsigned int brbrsvcontrol;
+	unsigned int brbrsvconfig;
+	unsigned int brbqosconfig;
+	unsigned char res301[0x14];
+	unsigned int wrlvl_config0;
+	unsigned int wrlvl_config1;
+	unsigned int wrlvl_status;
+	unsigned char res23[0x4];
+	unsigned int ppcclockon;
+	unsigned int perevconfig0;
+	unsigned int perevconfig1;
+	unsigned int perevconfig2;
+	unsigned int perevconfig3;
+	unsigned char res24[0xc];
+	unsigned int control_io_rdata;
+	unsigned char res240[0xc];
+	unsigned int cacal_config0;
+	unsigned int cacal_config1;
+	unsigned int cacal_status;
+	unsigned char res302[0xa4];
+	unsigned int bp_control0;
+	unsigned int bp_config0_r;
+	unsigned int bp_config0_w;
+	unsigned char res303[0x4];
+	unsigned int bp_control1;
+	unsigned int bp_config1_r;
+	unsigned int bp_config1_w;
+	unsigned char res304[0x4];
+	unsigned int bp_control2;
+	unsigned int bp_config2_r;
+	unsigned int bp_config2_w;
+	unsigned char res305[0x4];
+	unsigned int bp_control3;
+	unsigned int bp_config3_r;
+	unsigned int bp_config3_w;
+	unsigned char res306[0xddb4];
+	unsigned int pmnc_ppc;
+	unsigned char res25[0xc];
+	unsigned int cntens_ppc;
+	unsigned char res26[0xc];
+	unsigned int cntenc_ppc;
+	unsigned char res27[0xc];
+	unsigned int intens_ppc;
+	unsigned char res28[0xc];
+	unsigned int intenc_ppc;
+	unsigned char res29[0xc];
+	unsigned int flag_ppc;
+	unsigned char res30[0xac];
+	unsigned int ccnt_ppc;
+	unsigned char res31[0xc];
+	unsigned int pmcnt0_ppc;
+	unsigned char res32[0xc];
+	unsigned int pmcnt1_ppc;
+	unsigned char res33[0xc];
+	unsigned int pmcnt2_ppc;
+	unsigned char res34[0xc];
+	unsigned int pmcnt3_ppc;
+};
+
 struct exynos5_phy_control {
 	unsigned int phy_con0;
 	unsigned int phy_con1;
@@ -252,6 +373,52 @@ struct exynos5_phy_control {
 	unsigned int phy_con42;
 };
 
+struct exynos5420_phy_control {
+	unsigned int phy_con0;
+	unsigned int phy_con1;
+	unsigned int phy_con2;
+	unsigned int phy_con3;
+	unsigned int phy_con4;
+	unsigned int phy_con5;
+	unsigned int phy_con6;
+	unsigned char res2[0x4];
+	unsigned int phy_con8;
+	unsigned char res5[0x4];
+	unsigned int phy_con10;
+	unsigned int phy_con11;
+	unsigned int phy_con12;
+	unsigned int phy_con13;
+	unsigned int phy_con14;
+	unsigned int phy_con15;
+	unsigned int phy_con16;
+	unsigned char res4[0x4];
+	unsigned int phy_con17;
+	unsigned int phy_con18;
+	unsigned int phy_con19;
+	unsigned int phy_con20;
+	unsigned int phy_con21;
+	unsigned int phy_con22;
+	unsigned int phy_con23;
+	unsigned int phy_con24;
+	unsigned int phy_con25;
+	unsigned int phy_con26;
+	unsigned int phy_con27;
+	unsigned int phy_con28;
+	unsigned int phy_con29;
+	unsigned int phy_con30;
+	unsigned int phy_con31;
+	unsigned int phy_con32;
+	unsigned int phy_con33;
+	unsigned int phy_con34;
+	unsigned char res6[0x8];
+	unsigned int phy_con37;
+	unsigned char res7[0x4];
+	unsigned int phy_con39;
+	unsigned int phy_con40;
+	unsigned int phy_con41;
+	unsigned int phy_con42;
+};
+
 enum ddr_mode {
 	DDR_MODE_DDR2,
 	DDR_MODE_DDR3,
Signature · 1 line
1.7.12.4
#6 lore raw

PATCH v12 5/11 Exynos5420: Add clock initialization for 5420

In reply to Rajeshwari S Shinde

This patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic for exynos5420_set_spi_clk api.
Changes in V8:
- Chnages the if condition loop for pro_id and cpu_id.
Changes in V9:
- Used samsung_get_base to get base address of clock.
Changes in V10:
- Corrected the comments and few coding style nits.
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/cpu/armv7/exynos/clock.c              | 279 +++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 6 files changed, 1679 insertions(+), 202 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +264 -15
index 84a5047..5bde9d1 100644
@@ -96,7 +96,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 
 	freq = CONFIG_SYS_CLK_FREQ;
 
-	if (pllreg == EPLL) {
+	if (pllreg == EPLL || pllreg == RPLL) {
 		k = k & 0xffff;
 		/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */
 		fout = (m + k / PLL_DIV_65536) * (freq / (p * (1 << s)));
@@ -117,7 +117,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 			div = PLL_DIV_1024;
 		else if (proid_is_exynos4412())
 			div = PLL_DIV_65535;
-		else if (proid_is_exynos5250())
+		else if (proid_is_exynos5250() || proid_is_exynos5420())
 			div = PLL_DIV_65536;
 		else
 			return 0;
@@ -362,6 +362,43 @@ unsigned long clock_get_periph_rate(int peripheral)
 		return 0;
 }
 
+/* exynos5420: return pll clock frequency */
+static unsigned long exynos5420_get_pll_clk(int pllreg)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long r, k = 0;
+
+	switch (pllreg) {
+	case APLL:
+		r = readl(&clk->apll_con0);
+		break;
+	case MPLL:
+		r = readl(&clk->mpll_con0);
+		break;
+	case EPLL:
+		r = readl(&clk->epll_con0);
+		k = readl(&clk->epll_con1);
+		break;
+	case VPLL:
+		r = readl(&clk->vpll_con0);
+		k = readl(&clk->vpll_con1);
+		break;
+	case BPLL:
+		r = readl(&clk->bpll_con0);
+		break;
+	case RPLL:
+		r = readl(&clk->rpll_con0);
+		k = readl(&clk->rpll_con1);
+		break;
+	default:
+		printf("Unsupported PLL (%d)\n", pllreg);
+		return 0;
+	}
+
+	return exynos_get_pll_clk(pllreg, r, k);
+}
+
 /* exynos4: return ARM clock frequency */
 static unsigned long exynos4_get_arm_clk(void)
 {
@@ -485,6 +522,27 @@ static unsigned long exynos4x12_get_pwm_clk(void)
 	return pclk;
 }
 
+/* exynos5420: return pwm clock frequency */
+static unsigned long exynos5420_get_pwm_clk(void)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long pclk, sclk;
+	unsigned int ratio;
+
+	/*
+	 * CLK_DIV_PERIC0
+	 * PWM_RATIO [31:28]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> 28) & 0xf;
+	sclk = get_pll_clk(MPLL);
+
+	pclk = sclk / (ratio + 1);
+
+	return pclk;
+}
+
 /* exynos4: return uart clock frequency */
 static unsigned long exynos4_get_uart_clk(int dev_index)
 {
@@ -624,6 +682,53 @@ static unsigned long exynos5_get_uart_clk(int dev_index)
 	return uclk;
 }
 
+/* exynos5420: return uart clock frequency */
+static unsigned long exynos5420_get_uart_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel;
+	unsigned int ratio;
+
+	/*
+	 * CLK_SRC_PERIC0
+	 * UART0_SEL [6:4]
+	 * UART1_SEL [10:8]
+	 * UART2_SEL [14:12]
+	 * UART3_SEL [18:16]
+	 * generalised calculation as follows
+	 * sel = (sel >> ((dev_index * 4) + 4)) & mask;
+	 */
+	sel = readl(&clk->src_peric0);
+	sel = (sel >> ((dev_index * 4) + 4)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else if (sel == 0x7)
+		sclk = get_pll_clk(RPLL);
+	else
+		return 0;
+
+	/*
+	 * CLK_DIV_PERIC0
+	 * UART0_RATIO [11:8]
+	 * UART1_RATIO [15:12]
+	 * UART2_RATIO [19:16]
+	 * UART3_RATIO [23:20]
+	 * generalised calculation as follows
+	 * ratio = (ratio >> ((dev_index * 4) + 8)) & mask;
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> ((dev_index * 4) + 8)) & 0xf;
+
+	uclk = sclk / (ratio + 1);
+
+	return uclk;
+}
+
 static unsigned long exynos4_get_mmc_clk(int dev_index)
 {
 	struct exynos4_clock *clk =
@@ -718,6 +823,47 @@ static unsigned long exynos5_get_mmc_clk(int dev_index)
 	return uclk;
 }
 
+static unsigned long exynos5420_get_mmc_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel, ratio;
+
+	/*
+	 * CLK_SRC_FSYS
+	 * MMC0_SEL [10:8]
+	 * MMC1_SEL [14:12]
+	 * MMC2_SEL [18:16]
+	 * generalised calculation as follows
+	 * sel = (sel >> ((dev_index * 4) + 8)) & mask
+	 */
+	sel = readl(&clk->src_fsys);
+	sel = (sel >> ((dev_index * 4) + 8)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else
+		return 0;
+
+	/*
+	 * CLK_DIV_FSYS1
+	 * MMC0_RATIO [9:0]
+	 * MMC1_RATIO [19:10]
+	 * MMC2_RATIO [29:20]
+	 * generalised calculation as follows
+	 * ratio = (ratio >> (dev_index * 10)) & mask
+	 */
+	ratio = readl(&clk->div_fsys1);
+	ratio = (ratio >> (dev_index * 10)) & 0x3ff;
+
+	uclk = (sclk / (ratio + 1));
+
+	return uclk;
+}
+
 /* exynos4: set the mmc clock */
 static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
 {
@@ -804,6 +950,29 @@ static void exynos5_set_mmc_clk(int dev_index, unsigned int div)
 	writel(val, addr);
 }
 
+/* exynos5: set the mmc clock */
+static void exynos5420_set_mmc_clk(int dev_index, unsigned int div)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned int addr;
+	unsigned int val, shift;
+
+	/*
+	 * CLK_DIV_FSYS1
+	 * MMC0_RATIO [9:0]
+	 * MMC1_RATIO [19:10]
+	 * MMC2_RATIO [29:20]
+	 */
+	addr = (unsigned int)&clk->div_fsys1;
+	shift = dev_index * 10;
+
+	val = readl(addr);
+	val &= ~(0x3ff << shift);
+	val |= (div & 0x3ff) << shift;
+	writel(val, addr);
+}
+
 /* get_lcd_clk: return lcd clock frequency */
 static unsigned long exynos4_get_lcd_clk(void)
 {
@@ -1324,6 +1493,71 @@ static int exynos5_set_spi_clk(enum periph_id periph_id,
 	return 0;
 }
 
+static int exynos5420_set_spi_clk(enum periph_id periph_id,
+					unsigned int rate)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	int main;
+	unsigned int fine;
+	unsigned shift, pre_shift;
+	unsigned div_mask = 0xf, pre_div_mask = 0xff;
+	u32 *reg;
+	u32 *pre_reg;
+
+	main = clock_calc_best_scalar(4, 8, 400000000, rate, &fine);
+	if (main < 0) {
+		debug("%s: Cannot set clock rate for periph %d",
+		      __func__, periph_id);
+		return -1;
+	}
+	main = main - 1;
+	fine = fine - 1;
+
+	switch (periph_id) {
+	case PERIPH_ID_SPI0:
+		reg = &clk->div_peric1;
+		shift = 20;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 8;
+		break;
+	case PERIPH_ID_SPI1:
+		reg = &clk->div_peric1;
+		shift = 24;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 16;
+		break;
+	case PERIPH_ID_SPI2:
+		reg = &clk->div_peric1;
+		shift = 28;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 24;
+		break;
+	case PERIPH_ID_SPI3:
+		reg = &clk->div_isp1;
+		shift = 16;
+		pre_reg = &clk->div_isp1;
+		pre_shift = 0;
+		break;
+	case PERIPH_ID_SPI4:
+		reg = &clk->div_isp1;
+		shift = 20;
+		pre_reg = &clk->div_isp1;
+		pre_shift = 8;
+		break;
+	default:
+		debug("%s: Unsupported peripheral ID %d\n", __func__,
+		      periph_id);
+		return -1;
+	}
+
+	clrsetbits_le32(reg, div_mask << shift, (main & div_mask) << shift);
+	clrsetbits_le32(pre_reg, pre_div_mask << pre_shift,
+			(fine & pre_div_mask) << pre_shift);
+
+	return 0;
+}
+
 static unsigned long exynos4_get_i2c_clk(void)
 {
 	struct exynos4_clock *clk =
@@ -1341,9 +1575,11 @@ static unsigned long exynos4_get_i2c_clk(void)
 
 unsigned long get_pll_clk(int pllreg)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pll_clk(pllreg);
 		return exynos5_get_pll_clk(pllreg);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pll_clk(pllreg);
 		return exynos4_get_pll_clk(pllreg);
@@ -1375,9 +1611,11 @@ unsigned long get_i2c_clk(void)
 
 unsigned long get_pwm_clk(void)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pwm_clk();
 		return clock_get_periph_rate(PERIPH_ID_PWM0);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pwm_clk();
 		return exynos4_get_pwm_clk();
@@ -1386,9 +1624,11 @@ unsigned long get_pwm_clk(void)
 
 unsigned long get_uart_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_uart_clk(dev_index);
 		return exynos5_get_uart_clk(dev_index);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_uart_clk(dev_index);
 		return exynos4_get_uart_clk(dev_index);
@@ -1397,17 +1637,23 @@ unsigned long get_uart_clk(int dev_index)
 
 unsigned long get_mmc_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_mmc_clk(dev_index);
 		return exynos5_get_mmc_clk(dev_index);
-	else
+	} else {
 		return exynos4_get_mmc_clk(dev_index);
+	}
 }
 
 void set_mmc_clk(int dev_index, unsigned int div)
 {
-	if (cpu_is_exynos5())
-		exynos5_set_mmc_clk(dev_index, div);
-	else {
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			exynos5420_set_mmc_clk(dev_index, div);
+		else
+			exynos5_set_mmc_clk(dev_index, div);
+	} else {
 		if (proid_is_exynos4412())
 			exynos4x12_set_mmc_clk(dev_index, div);
 		else
@@ -1439,10 +1685,13 @@ void set_mipi_clk(void)
 
 int set_spi_clk(int periph_id, unsigned int rate)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_set_spi_clk(periph_id, rate);
 		return exynos5_set_spi_clk(periph_id, rate);
-	else
+	} else {
 		return 0;
+	}
 }
 
 int set_i2s_clk_prescaler(unsigned int src_frq, unsigned int dst_frq,
arch/arm/cpu/armv7/exynos/clock_init.h +17 -0
index c28ff3a..a875d0b 100644
@@ -10,7 +10,11 @@
 #define __EXYNOS_CLOCK_INIT_H
 
 enum {
+#ifdef CONFIG_EXYNOS5420
+	MEM_TIMINGS_MSR_COUNT	= 5,
+#else
 	MEM_TIMINGS_MSR_COUNT	= 4,
+#endif
 };
 
 /* These are the ratio's for configuring ARM clock */
@@ -59,6 +63,18 @@ struct mem_timings {
 	unsigned bpll_mdiv;
 	unsigned bpll_pdiv;
 	unsigned bpll_sdiv;
+	unsigned kpll_mdiv;
+	unsigned kpll_pdiv;
+	unsigned kpll_sdiv;
+	unsigned dpll_mdiv;
+	unsigned dpll_pdiv;
+	unsigned dpll_sdiv;
+	unsigned ipll_mdiv;
+	unsigned ipll_pdiv;
+	unsigned ipll_sdiv;
+	unsigned spll_mdiv;
+	unsigned spll_pdiv;
+	unsigned spll_sdiv;
 	unsigned pclk_cdrex_ratio;
 	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
 
@@ -115,6 +131,7 @@ struct mem_timings {
 	uint8_t send_zq_init;		/* 1 to send this command */
 	unsigned impedance;		/* drive strength impedeance */
 	uint8_t gate_leveling_enable;	/* check gate leveling is enabled */
+	uint8_t read_leveling_enable;	/* check h/w read leveling is enabled */
 };
 
 /**
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +338 -14

390 lines not on this page · raw message

arch/arm/cpu/armv7/exynos/exynos5_setup.h +565 -173

854 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/clk.h +1 -0
index 1d6fa93..cdeef32 100644
@@ -14,6 +14,7 @@
 #define HPLL	3
 #define VPLL	4
 #define BPLL	5
+#define RPLL	6
 
 enum pll_src_bit {
 	EXYNOS_SRC_MPLL = 6,
arch/arm/include/asm/arch-exynos/clock.h +494 -0

500 lines not on this page · raw message

Signature · 1 line
1.7.12.4
#7 lore raw

PATCH v12 6/11 Exynos5420: Add DDR3 initialization for 5420

In reply to Rajeshwari S Shinde

This patch intends to add DDR3 initialization code for Exynos5420.

---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None
Changes in V9:
- Used samsung_get base to get the dmc base address
Changes in V10:
- Changed to new 5420 dmc and power resgister structure.
- Changed the input parameters for dmc common functions due to changes in the dmc register structure.
Changes in V11:
- None
Changes in V12:
- Changed const void* to uint32_t *

 arch/arm/cpu/armv7/exynos/dmc_common.c    |  60 ++--
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 +++++++++++++++++++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h |  26 +-
 arch/arm/include/asm/arch-exynos/cpu.h    |   7 +-
 arch/arm/include/asm/arch-exynos/dmc.h    |  10 +
 5 files changed, 484 insertions(+), 58 deletions(-)
arch/arm/cpu/armv7/exynos/dmc_common.c +26 -34
index 53cfe6e..cca925e 100644
@@ -1,5 +1,5 @@
 /*
- * Mem setup common file for different types of DDR present on SMDK5250 boards.
+ * Mem setup common file for different types of DDR present on Exynos boards.
  *
  * Copyright (C) 2012 Samsung Electronics
  *
@@ -15,9 +15,9 @@
 
 #define ZQ_INIT_TIMEOUT	10000
 
-int dmc_config_zq(struct mem_timings *mem,
-		  struct exynos5_phy_control *phy0_ctrl,
-		  struct exynos5_phy_control *phy1_ctrl)
+int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16,
+			uint32_t *phy1_con16, uint32_t *phy0_con17,
+			uint32_t *phy1_con17)
 {
 	unsigned long val = 0;
 	int i;
@@ -31,19 +31,19 @@ int dmc_config_zq(struct mem_timings *mem,
 	val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
 	val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
 	val |= ZQ_CLK_DIV_EN;
-	writel(val, &phy0_ctrl->phy_con16);
-	writel(val, &phy1_ctrl->phy_con16);
+	writel(val, phy0_con16);
+	writel(val, phy1_con16);
 
 	/* Disable termination */
 	if (mem->zq_mode_noterm)
 		val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
-	writel(val, &phy0_ctrl->phy_con16);
-	writel(val, &phy1_ctrl->phy_con16);
+	writel(val, phy0_con16);
+	writel(val, phy1_con16);
 
 	/* ZQ_MANUAL_START: Enable */
 	val |= ZQ_MANUAL_STR;
-	writel(val, &phy0_ctrl->phy_con16);
-	writel(val, &phy1_ctrl->phy_con16);
+	writel(val, phy0_con16);
+	writel(val, phy1_con16);
 
 	/* ZQ_MANUAL_START: Disable */
 	val &= ~ZQ_MANUAL_STR;
@@ -53,47 +53,47 @@ int dmc_config_zq(struct mem_timings *mem,
 	 * we are looping for the ZQ_init to complete.
 	 */
 	i = ZQ_INIT_TIMEOUT;
-	while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+	while ((readl(phy0_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
 		sdelay(100);
 		i--;
 	}
 	if (!i)
 		return -1;
-	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, phy0_con16);
 
 	i = ZQ_INIT_TIMEOUT;
-	while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+	while ((readl(phy1_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
 		sdelay(100);
 		i--;
 	}
 	if (!i)
 		return -1;
-	writel(val, &phy1_ctrl->phy_con16);
+	writel(val, phy1_con16);
 
 	return 0;
 }
 
-void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
+void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode mode)
 {
 	unsigned long val;
 
 	if (mode == DDR_MODE_DDR3) {
 		val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
-		writel(val, &dmc->phycontrol0);
+		writel(val, phycontrol0);
 	}
 
 	/* Update DLL Information: Force DLL Resyncronization */
-	val = readl(&dmc->phycontrol0);
+	val = readl(phycontrol0);
 	val |= FP_RSYNC;
-	writel(val, &dmc->phycontrol0);
+	writel(val, phycontrol0);
 
 	/* Reset Force DLL Resyncronization */
-	val = readl(&dmc->phycontrol0);
+	val = readl(phycontrol0);
 	val &= ~FP_RSYNC;
-	writel(val, &dmc->phycontrol0);
+	writel(val, phycontrol0);
 }
 
-void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
+void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd)
 {
 	int channel, chip;
 
@@ -107,7 +107,7 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
 			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
 
 			/* Sending NOP command */
-			writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
+			writel(DIRECT_CMD_NOP | mask, directcmd);
 
 			/*
 			 * TODO(alim.akhtar at samsung.com): Do we need these
@@ -119,14 +119,14 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
 			/* Sending EMRS/MRS commands */
 			for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
 				writel(mem->direct_cmd_msr[i] | mask,
-				       &dmc->directcmd);
+				       directcmd);
 				sdelay(0x10000);
 			}
 
 			if (mem->send_zq_init) {
 				/* Sending ZQINIT command */
 				writel(DIRECT_CMD_ZQINIT | mask,
-				       &dmc->directcmd);
+				       directcmd);
 
 				sdelay(10000);
 			}
@@ -134,7 +134,7 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
 	}
 }
 
-void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
+void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd)
 {
 	int channel, chip;
 
@@ -146,20 +146,12 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
 			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
 
 			/* PALL (all banks precharge) CMD */
-			writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
+			writel(DIRECT_CMD_PALL | mask, directcmd);
 			sdelay(0x10000);
 		}
 	}
 }
 
-void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
-{
-	writel(mem->memconfig, &dmc->memconfig0);
-	writel(mem->memconfig, &dmc->memconfig1);
-	writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
-	writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
-}
-
 void mem_ctrl_init(int reset)
 {
 	struct spl_machine_param *param = spl_get_machine_params();
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +429 -10

498 lines not on this page · raw message

arch/arm/cpu/armv7/exynos/exynos5_setup.h +14 -12
index c8d6515..53b0ace 100644
@@ -696,6 +696,7 @@
 #define CLK_DIV_CPERI1_VAL	NOT_AVAILABLE
 
 #else
+#define PAD_RETENTION_DRAM_COREBLK_VAL	0x10000000
 
 /* APLL_CON1 */
 #define APLL_CON1_VAL	(0x0020F300)
@@ -907,37 +908,38 @@ void lpddr3_mem_ctrl_init(void);
  * Configure ZQ I/O interface
  *
  * @param mem		Memory timings for this memory type.
- * @param phy0_ctrl	Pointer to struct containing PHY0 control reg
- * @param phy1_ctrl	Pointer to struct containing PHY1 control reg
+ * @param phy0_con16	Register address for dmc_phy0->phy_con16
+ * @param phy1_con16	Register address for dmc_phy1->phy_con16
+ * @param phy0_con17	Register address for dmc_phy0->phy_con17
+ * @param phy1_con17	Register address for dmc_phy1->phy_con17
  * @return 0 if ok, -1 on error
  */
-int dmc_config_zq(struct mem_timings *mem,
-		  struct exynos5_phy_control *phy0_ctrl,
-		  struct exynos5_phy_control *phy1_ctrl);
-
+int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16,
+			uint32_t *phy1_con16, uint32_t *phy0_con17,
+			uint32_t *phy1_con17);
 /*
  * Send NOP and MRS/EMRS Direct commands
  *
  * @param mem		Memory timings for this memory type.
- * @param dmc		Pointer to struct of DMC registers
+ * @param directcmd	Register address for dmc_phy->directcmd
  */
-void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
+void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd);
 
 /*
  * Send PALL Direct commands
  *
  * @param mem		Memory timings for this memory type.
- * @param dmc		Pointer to struct of DMC registers
+ * @param directcmd	Register address for dmc_phy->directcmd
  */
-void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
+void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd);
 
 /*
  * Reset the DLL. This function is common between DDR3 and LPDDR2.
  * However, the reset value is different. So we are passing a flag
  * ddr_mode to distinguish between LPDDR2 and DDR3.
  *
- * @param exynos5_dmc	Pointer to struct of DMC registers
+ * @param phycontrol0	Register address for dmc_phy->phycontrol0
  * @param ddr_mode	Type of DDR memory
  */
-void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
+void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode);
 #endif
arch/arm/include/asm/arch-exynos/cpu.h +5 -2
index 2b44210..573f755 100644
@@ -53,6 +53,7 @@
 #define EXYNOS4_AUDIOSS_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4_USB_HOST_XHCI_BASE	DEVICE_NOT_AVAILABLE
 #define EXYNOS4_USB3PHY_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS4_DMC_TZASC_BASE		DEVICE_NOT_AVAILABLE
 
 /* EXYNOS4X12 */
 #define EXYNOS4X12_GPIO_PART3_BASE	0x03860000
@@ -91,6 +92,7 @@
 #define EXYNOS4X12_AUDIOSS_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_USB_HOST_XHCI_BASE	DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_USB3PHY_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_DMC_TZASC_BASE	DEVICE_NOT_AVAILABLE
 
 /* EXYNOS5 */
 #define EXYNOS5_I2C_SPACING		0x10000
@@ -129,6 +131,7 @@
 
 #define EXYNOS5_ADC_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS5_MODEM_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5_DMC_TZASC_BASE		DEVICE_NOT_AVAILABLE
 
 /* EXYNOS5420 */
 #define EXYNOS5420_AUDIOSS_BASE		0x03810000
@@ -143,8 +146,7 @@
 #define EXYNOS5420_ACE_SFR_BASE		0x10830000
 #define EXYNOS5420_DMC_PHY_BASE		0x10C00000
 #define EXYNOS5420_DMC_CTRL_BASE	0x10C20000
-#define EXYNOS5420_DMC_TZASC0_BASE	0x10D40000
-#define EXYNOS5420_DMC_TZASC1_BASE	0x10D50000
+#define EXYNOS5420_DMC_TZASC_BASE	0x10D40000
 #define EXYNOS5420_USB_HOST_EHCI_BASE	0x12110000
 #define EXYNOS5420_MMC_BASE		0x12200000
 #define EXYNOS5420_SROMC_BASE		0x12250000
@@ -284,6 +286,7 @@ SAMSUNG_BASE(spi_isp, SPI_ISP_BASE)
 SAMSUNG_BASE(tzpc, TZPC_BASE)
 SAMSUNG_BASE(dmc_ctrl, DMC_CTRL_BASE)
 SAMSUNG_BASE(dmc_phy, DMC_PHY_BASE)
+SAMSUNG_BASE(dmc_tzasc, DMC_TZASC_BASE)
 SAMSUNG_BASE(audio_ass, AUDIOSS_BASE)
 #endif
 
arch/arm/include/asm/arch-exynos/dmc.h +10 -0
index 32ad3ae..d78536d 100644
@@ -419,6 +419,15 @@ struct exynos5420_phy_control {
 	unsigned int phy_con42;
 };
 
+struct exynos5420_tzasc {
+	unsigned char res1[0xf00];
+	unsigned int membaseconfig0;
+	unsigned int membaseconfig1;
+	unsigned char res2[0x8];
+	unsigned int memconfig0;
+	unsigned int memconfig1;
+};
+
 enum ddr_mode {
 	DDR_MODE_DDR2,
 	DDR_MODE_DDR3,
@@ -453,6 +462,7 @@ enum mem_manuf {
 #define PHY_CON0_T_WRRDCMD_SHIFT	17
 #define PHY_CON0_T_WRRDCMD_MASK		(0x7 << PHY_CON0_T_WRRDCMD_SHIFT)
 #define PHY_CON0_CTRL_DDR_MODE_SHIFT	11
+#define PHY_CON0_CTRL_DDR_MODE_MASK	0x3
 
 /* PHY_CON1 register fields */
 #define PHY_CON1_RDLVL_RDDATA_ADJ_SHIFT	0
Signature · 1 line
1.7.12.4
#8 lore raw

PATCH v12 6/11 Exynos5420: Add DDR3 initialization for 5420

Quoted 4 lines · Rajeshwari S Shinde

This patch intends to add DDR3 initialization code for Exynos5420.

Quoted 32 lines

---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None
Changes in V9:
- Used samsung_get base to get the dmc base address
Changes in V10:
- Changed to new 5420 dmc and power resgister structure.
- Changed the input parameters for dmc common functions due to changes in the dmc register structure.
Changes in V11:
- None
Changes in V12:
- Changed const void* to uint32_t *

 arch/arm/cpu/armv7/exynos/dmc_common.c    |  60 ++--
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 +++++++++++++++++++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h |  26 +-
 arch/arm/include/asm/arch-exynos/cpu.h    |   7 +-
 arch/arm/include/asm/arch-exynos/dmc.h    |  10 +
 5 files changed, 484 insertions(+), 58 deletions(-)
#9 lore raw

PATCH v12 7/11 Exynos5420: Add support for 5420 in pinmux and gpio

In reply to Rajeshwari S Shinde

Adds code in pinmux and gpio framework to support Exynos5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added correct calculation of gpio based addresses.
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the coding style nits.
Chnages in V8:
- Corrected the coding style nits pointed by Minkyu Kang.
Changes in V9:
- None
Changes in V10:
- None
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/cpu/armv7/exynos/pinmux.c        | 260 +++++++++++++++++++++++++++++-
 arch/arm/include/asm/arch-exynos/gpio.h   | 143 ++++++++++++++--
 arch/arm/include/asm/arch-exynos/periph.h |   3 +
 3 files changed, 390 insertions(+), 16 deletions(-)
arch/arm/cpu/armv7/exynos/pinmux.c +258 -2
index 74cc700..904177a 100644
@@ -46,6 +46,42 @@ static void exynos5_uart_config(int peripheral)
 	}
 }
 
+static void exynos5420_uart_config(int peripheral)
+{
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+	struct s5p_gpio_bank *bank;
+	int i, start, count;
+
+	switch (peripheral) {
+	case PERIPH_ID_UART0:
+		bank = &gpio1->a0;
+		start = 0;
+		count = 4;
+		break;
+	case PERIPH_ID_UART1:
+		bank = &gpio1->a0;
+		start = 4;
+		count = 4;
+		break;
+	case PERIPH_ID_UART2:
+		bank = &gpio1->a1;
+		start = 0;
+		count = 4;
+		break;
+	case PERIPH_ID_UART3:
+		bank = &gpio1->a1;
+		start = 4;
+		count = 2;
+		break;
+	}
+
+	for (i = start; i < start + count; i++) {
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
+		s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+	}
+}
+
 static int exynos5_mmc_config(int peripheral, int flags)
 {
 	struct exynos5_gpio_part1 *gpio1 =
@@ -101,6 +137,75 @@ static int exynos5_mmc_config(int peripheral, int flags)
 	return 0;
 }
 
+static int exynos5420_mmc_config(int peripheral, int flags)
+{
+	struct exynos5420_gpio_part3 *gpio3 =
+		(struct exynos5420_gpio_part3 *)samsung_get_base_gpio_part3();
+	struct s5p_gpio_bank *bank = NULL, *bank_ext = NULL;
+	int i, start;
+
+	switch (peripheral) {
+	case PERIPH_ID_SDMMC0:
+		bank = &gpio3->c0;
+		bank_ext = &gpio3->c3;
+		start = 0;
+		break;
+	case PERIPH_ID_SDMMC1:
+		bank = &gpio3->c1;
+		bank_ext = &gpio3->d1;
+		start = 4;
+		break;
+	case PERIPH_ID_SDMMC2:
+		bank = &gpio3->c2;
+		bank_ext = NULL;
+		start = 0;
+		break;
+	default:
+		start = 0;
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return -1;
+	}
+
+	if ((flags & PINMUX_FLAG_8BIT_MODE) && !bank_ext) {
+		debug("SDMMC device %d does not support 8bit mode",
+		      peripheral);
+		return -1;
+	}
+
+	if (flags & PINMUX_FLAG_8BIT_MODE) {
+		for (i = start; i <= (start + 3); i++) {
+			s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x2));
+			s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_UP);
+			s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X);
+		}
+	}
+
+	for (i = 0; i < 3; i++) {
+		/*
+		 * MMC0 is intended to be used for eMMC. The
+		 * card detect pin is used as a VDDEN signal to
+		 * power on the eMMC. The 5420 iROM makes
+		 * this same assumption.
+		 */
+		if ((peripheral == PERIPH_ID_SDMMC0) && (i == 2)) {
+			s5p_gpio_set_value(bank, i, 1);
+			s5p_gpio_cfg_pin(bank, i, GPIO_OUTPUT);
+		} else {
+			s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+		}
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
+		s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
+	}
+
+	for (i = 3; i <= 6; i++) {
+		s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_UP);
+		s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
+	}
+
+	return 0;
+}
+
 static void exynos5_sromc_config(int flags)
 {
 	struct exynos5_gpio_part1 *gpio1 =
@@ -216,6 +321,59 @@ static void exynos5_i2c_config(int peripheral, int flags)
 	}
 }
 
+static void exynos5420_i2c_config(int peripheral)
+{
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+
+	switch (peripheral) {
+	case PERIPH_ID_I2C0:
+		s5p_gpio_cfg_pin(&gpio1->b3, 0, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 1, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C1:
+		s5p_gpio_cfg_pin(&gpio1->b3, 2, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 3, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C2:
+		s5p_gpio_cfg_pin(&gpio1->a0, 6, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a0, 7, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C3:
+		s5p_gpio_cfg_pin(&gpio1->a1, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a1, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C4:
+		s5p_gpio_cfg_pin(&gpio1->a2, 0, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a2, 1, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C5:
+		s5p_gpio_cfg_pin(&gpio1->a2, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a2, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C6:
+		s5p_gpio_cfg_pin(&gpio1->b1, 3, GPIO_FUNC(0x4));
+		s5p_gpio_cfg_pin(&gpio1->b1, 4, GPIO_FUNC(0x4));
+		break;
+	case PERIPH_ID_I2C7:
+		s5p_gpio_cfg_pin(&gpio1->b2, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->b2, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C8:
+		s5p_gpio_cfg_pin(&gpio1->b3, 4, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 5, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C9:
+		s5p_gpio_cfg_pin(&gpio1->b3, 6, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 7, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C10:
+		s5p_gpio_cfg_pin(&gpio1->b4, 0, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b4, 1, GPIO_FUNC(0x2));
+		break;
+	}
+}
+
 static void exynos5_i2s_config(int peripheral)
 {
 	int i;
@@ -279,6 +437,58 @@ void exynos5_spi_config(int peripheral)
 	}
 }
 
+void exynos5420_spi_config(int peripheral)
+{
+	int cfg, pin, i;
+	struct s5p_gpio_bank *bank = NULL;
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+	struct exynos5420_gpio_part4 *gpio4 =
+		(struct exynos5420_gpio_part4 *)samsung_get_base_gpio_part4();
+
+	switch (peripheral) {
+	case PERIPH_ID_SPI0:
+		bank = &gpio1->a2;
+		cfg = GPIO_FUNC(0x2);
+		pin = 0;
+		break;
+	case PERIPH_ID_SPI1:
+		bank = &gpio1->a2;
+		cfg = GPIO_FUNC(0x2);
+		pin = 4;
+		break;
+	case PERIPH_ID_SPI2:
+		bank = &gpio1->b1;
+		cfg = GPIO_FUNC(0x5);
+		pin = 1;
+		break;
+	case PERIPH_ID_SPI3:
+		bank = &gpio4->f1;
+		cfg = GPIO_FUNC(0x2);
+		pin = 0;
+		break;
+	case PERIPH_ID_SPI4:
+		cfg = 0;
+		pin = 0;
+		break;
+	default:
+		cfg = 0;
+		pin = 0;
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return;
+	}
+
+	if (peripheral != PERIPH_ID_SPI4) {
+		for (i = pin; i < pin + 4; i++)
+			s5p_gpio_cfg_pin(bank, i, cfg);
+	} else {
+		for (i = 0; i < 2; i++) {
+			s5p_gpio_cfg_pin(&gpio4->f0, i + 2, GPIO_FUNC(0x4));
+			s5p_gpio_cfg_pin(&gpio4->e0, i + 4, GPIO_FUNC(0x4));
+		}
+	}
+}
+
 static int exynos5_pinmux_config(int peripheral, int flags)
 {
 	switch (peripheral) {
@@ -325,6 +535,48 @@ static int exynos5_pinmux_config(int peripheral, int flags)
 	return 0;
 }
 
+static int exynos5420_pinmux_config(int peripheral, int flags)
+{
+	switch (peripheral) {
+	case PERIPH_ID_UART0:
+	case PERIPH_ID_UART1:
+	case PERIPH_ID_UART2:
+	case PERIPH_ID_UART3:
+		exynos5420_uart_config(peripheral);
+		break;
+	case PERIPH_ID_SDMMC0:
+	case PERIPH_ID_SDMMC1:
+	case PERIPH_ID_SDMMC2:
+	case PERIPH_ID_SDMMC3:
+		return exynos5420_mmc_config(peripheral, flags);
+	case PERIPH_ID_SPI0:
+	case PERIPH_ID_SPI1:
+	case PERIPH_ID_SPI2:
+	case PERIPH_ID_SPI3:
+	case PERIPH_ID_SPI4:
+		exynos5420_spi_config(peripheral);
+		break;
+	case PERIPH_ID_I2C0:
+	case PERIPH_ID_I2C1:
+	case PERIPH_ID_I2C2:
+	case PERIPH_ID_I2C3:
+	case PERIPH_ID_I2C4:
+	case PERIPH_ID_I2C5:
+	case PERIPH_ID_I2C6:
+	case PERIPH_ID_I2C7:
+	case PERIPH_ID_I2C8:
+	case PERIPH_ID_I2C9:
+	case PERIPH_ID_I2C10:
+		exynos5420_i2c_config(peripheral);
+		break;
+	default:
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return -1;
+	}
+
+	return 0;
+}
+
 static void exynos4_i2c_config(int peripheral, int flags)
 {
 	struct exynos4_gpio_part1 *gpio1 =
@@ -475,13 +727,17 @@ static int exynos4_pinmux_config(int peripheral, int flags)
 int exynos_pinmux_config(int peripheral, int flags)
 {
 	if (cpu_is_exynos5()) {
-		return exynos5_pinmux_config(peripheral, flags);
+		if (proid_is_exynos5420())
+			return exynos5420_pinmux_config(peripheral, flags);
+		else if (proid_is_exynos5250())
+			return exynos5_pinmux_config(peripheral, flags);
 	} else if (cpu_is_exynos4()) {
 		return exynos4_pinmux_config(peripheral, flags);
 	} else {
 		debug("pinmux functionality not supported\n");
-		return -1;
 	}
+
+	return -1;
 }
 
 #ifdef CONFIG_OF_CONTROL
arch/arm/include/asm/arch-exynos/gpio.h +129 -14

164 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/periph.h +3 -0
index 64bd8b7..30c7f18 100644
@@ -34,6 +34,9 @@ enum periph_id {
 	PERIPH_ID_SDMMC1,
 	PERIPH_ID_SDMMC2,
 	PERIPH_ID_SDMMC3,
+	PERIPH_ID_I2C8 = 87,
+	PERIPH_ID_I2C9,
+	PERIPH_ID_I2C10 = 203,
 	PERIPH_ID_I2S0 = 98,
 	PERIPH_ID_I2S1 = 99,
 
Signature · 1 line
1.7.12.4
#10 lore raw

PATCH v12 8/11 Exynos5420: Add base patch for SMDK5420

In reply to Rajeshwari S Shinde

Adding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functions board_eth_init and board_mmc_init as they were moved to common/board.c
Changes in V6:
- None
Changes in V7:
- added CONFIG_EXYNOS_SPL to build 5420 and 5250
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None

 board/samsung/common/board.c          |   2 +
 board/samsung/smdk5420/Makefile       |  11 +++
 board/samsung/smdk5420/smdk5420.c     | 159 ++++++++++++++++++++++++++++++++++
 board/samsung/smdk5420/smdk5420_spl.c |  52 +++++++++++
 boards.cfg                            |   1 +
 include/configs/arndale.h             |   1 +
 include/configs/exynos5250-dt.h       |   1 +
 tools/Makefile                        |   3 +-
 8 files changed, 229 insertions(+), 1 deletion(-)
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
board/samsung/common/board.c +2 -0
index 95df346..a5cb568 100644
@@ -146,6 +146,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)
 	return local.cros_ec_dev;
 }
 
+#ifdef CONFIG_CROS_EC
 static int board_init_cros_ec_devices(const void *blob)
 {
 	local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev);
@@ -154,6 +155,7 @@ static int board_init_cros_ec_devices(const void *blob)
 
 	return 0;
 }
+#endif
 
 #if defined(CONFIG_POWER)
 #ifdef CONFIG_POWER_MAX77686
board/samsung/smdk5420/Makefile new file +11 -0
new file mode 100644
index 0000000..c2f8886
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2013 Samsung Electronics
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	+= smdk5420_spl.o
+
+ifndef CONFIG_SPL_BUILD
+obj-y	+= smdk5420.o
+endif
board/samsung/smdk5420/smdk5420.c new file +159 -0

159 lines not on this page · raw message

board/samsung/smdk5420/smdk5420_spl.c new file +52 -0

52 lines not on this page · raw message

boards.cfg +1 -0
index 2128996..c7376b3 100644
@@ -276,6 +276,7 @@ Active  arm         armv7          exynos      samsung         arndale
 Active  arm         armv7          exynos      samsung         origen              origen                               -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            smdk5250                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            snow                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
+Active  arm         armv7          exynos      samsung         smdk5420            smdk5420                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
 Active  arm         armv7          exynos      samsung         smdkv310            smdkv310                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         trats               trats                                -                                                                                                                                 Lukasz Majewski <[email protected]>
 Active  arm         armv7          exynos      samsung         trats2              trats2                               -                                                                                                                                 Piotr Wilczek <[email protected]>
include/configs/arndale.h +1 -0
index f0b9f94..f431d20 100644
@@ -117,6 +117,7 @@
 #define CONFIG_USB_STORAGE
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
include/configs/exynos5250-dt.h +1 -0
index c625524..51b2623 100644
@@ -155,6 +155,7 @@
 #define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
tools/Makefile +2 -1
index 14d94e3..d4bc84d 100644
@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
 BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX)
+BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX)
 BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o
 OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o
 OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o
 OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o
-OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o
+OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o
 OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o
 OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o
 OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
Signature · 1 line
1.7.12.4
#11 lore raw

PATCH v12 9/11 DTS: Add dts support for SMDK5420

In reply to Rajeshwari S Shinde

This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common to both 5420 and 5250.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added /include/ "exynos5420.dtsi
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the license.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None

 arch/arm/dts/exynos5.dtsi                 | 198 ++++++++++++++++++++++++++++++
 arch/arm/dts/exynos5250.dtsi              | 194 +----------------------------
 arch/arm/dts/exynos5420.dtsi              |  70 +++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++++++++++++++++++++++
 4 files changed, 441 insertions(+), 190 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
arch/arm/dts/exynos5.dtsi new file +198 -0
new file mode 100644
index 0000000..f8c8741
@@ -0,0 +1,198 @@
+/*
+ * Copyright (c) 2013 The Chromium OS Authors
+ * SAMSUNG EXYNOS5 SoC device tree source
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "samsung,exynos5";
+
+	sromc at 12250000 {
+		compatible = "samsung,exynos-sromc";
+		reg = <0x12250000 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c at 12c60000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C60000 0x100>;
+		interrupts = <0 56 0>;
+	};
+
+	i2c at 12c70000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C70000 0x100>;
+		interrupts = <0 57 0>;
+	};
+
+	i2c at 12c80000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C80000 0x100>;
+		interrupts = <0 58 0>;
+	};
+
+	i2c at 12c90000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C90000 0x100>;
+		interrupts = <0 59 0>;
+	};
+
+	spi at 12d20000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d20000 0x30>;
+		interrupts = <0 68 0>;
+	};
+
+	spi at 12d30000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d30000 0x30>;
+		interrupts = <0 69 0>;
+	};
+
+	spi at 12d40000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d40000 0x30>;
+		clock-frequency = <50000000>;
+		interrupts = <0 70 0>;
+        };
+
+	spi at 131a0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x131a0000 0x30>;
+		interrupts = <0 129 0>;
+	};
+
+	spi at 131b0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x131b0000 0x30>;
+		interrupts = <0 130 0>;
+	};
+
+	ehci at 12110000 {
+		compatible = "samsung,exynos-ehci";
+		reg = <0x12110000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		phy {
+			compatible = "samsung,exynos-usb-phy";
+			reg = <0x12130000 0x100>;
+		};
+	};
+
+	tmu at 10060000 {
+		compatible = "samsung,exynos-tmu";
+		reg = <0x10060000 0x10000>;
+	};
+
+	fimd at 14400000 {
+		compatible = "samsung,exynos-fimd";
+		reg = <0x14400000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	dp at 145b0000 {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145b0000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	xhci0: xhci at 12000000 {
+		compatible = "samsung,exynos5250-xhci";
+		reg = <0x12000000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		phy {
+			compatible = "samsung,exynos5250-usb3-phy";
+			reg = <0x12100000 0x100>;
+		};
+	};
+
+	mmc at 12200000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+	};
+
+	mmc at 12210000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12210000 0x1000>;
+		interrupts = <0 76 0>;
+	};
+
+	mmc at 12220000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12220000 0x1000>;
+		interrupts = <0 77 0>;
+	};
+
+	mmc at 12230000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12230000 0x1000>;
+		interrupts = <0 78 0>;
+	};
+
+	serial at 12C00000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C00000 0x100>;
+		interrupts = <0 51 0>;
+		id = <0>;
+	};
+
+	serial at 12C10000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C10000 0x100>;
+		interrupts = <0 52 0>;
+		id = <1>;
+	};
+
+	serial at 12C20000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C20000 0x100>;
+		interrupts = <0 53 0>;
+		id = <2>;
+	};
+
+	serial at 12C30000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C30000 0x100>;
+		interrupts = <0 54 0>;
+		id = <3>;
+	};
+
+	gpio: gpio {
+	};
+};
arch/arm/dts/exynos5250.dtsi +4 -190

213 lines not on this page · raw message

arch/arm/dts/exynos5420.dtsi new file +70 -0

70 lines not on this page · raw message

board/samsung/dts/exynos5420-smdk5420.dts new file +169 -0

169 lines not on this page · raw message

Signature · 1 line
1.7.12.4
#12 lore raw

PATCH v12 10/11 Config: Add initial config for SMDK5420

In reply to Rajeshwari S Shinde

Adding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None

 include/configs/exynos5-dt.h    | 289 ++++++++++++++++++++++++++++++++++++++++
 include/configs/exynos5250-dt.h | 286 +--------------------------------------
 include/configs/smdk5420.h      |  50 +++++++
 3 files changed, 346 insertions(+), 279 deletions(-)
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h
include/configs/exynos5-dt.h new file +289 -0
new file mode 100644
index 0000000..4ca883d
@@ -0,0 +1,289 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG			/* in a SAMSUNG core */
+#define CONFIG_S5P			/* S5P Family */
+#define CONFIG_EXYNOS5			/* which is in a Exynos5 Family */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_COMMON
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_EXYNOS_SPL
+
+/* Enable fdt support for Exynos5250 */
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* Allow tracing to be enabled */
+#define CONFIG_TRACE
+#define CONFIG_CMD_TRACE
+#define CONFIG_TRACE_BUFFER_SIZE	(16 << 20)
+#define CONFIG_TRACE_EARLY_SIZE		(8 << 20)
+#define CONFIG_TRACE_EARLY
+#define CONFIG_TRACE_EARLY_ADDR		0x50000000
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_CACHELINE_SIZE	64
+
+/* Enable ACE acceleration for SHA1 and SHA256 */
+#define CONFIG_EXYNOS_ACE_SHA
+#define CONFIG_SHA_HW_ACCEL
+
+/* input clock of PLL: SMDK5250 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+#define S5P_CHECK_LPA			0xABAD0000
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET			0x800
+#define INFORM1_OFFSET			0x804
+#define INFORM2_OFFSET			0x808
+#define INFORM3_OFFSET			0x80c
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (4 << 20))
+
+/* select serial console configuration */
+#define CONFIG_BAUDRATE			115200
+#define EXYNOS5_DEFAULT_UART_OFFSET	0x010000
+#define CONFIG_SILENT_CONSOLE
+
+/* Enable keyboard */
+#define CONFIG_CROS_EC		/* CROS_EC protocol */
+#define CONFIG_CROS_EC_SPI		/* Support CROS_EC over SPI */
+#define CONFIG_CROS_EC_I2C		/* Support CROS_EC over I2C */
+#define CONFIG_CROS_EC_KEYB	/* CROS_EC keyboard input */
+#define CONFIG_CMD_CROS_EC
+#define CONFIG_KEYBOARD
+
+/* Console configuration */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define EXYNOS_DEVICE_SETTINGS \
+		"stdin=serial,cros-ec-keyb\0" \
+		"stdout=serial,lcd\0" \
+		"stderr=serial,lcd\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	EXYNOS_DEVICE_SETTINGS
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_SDHCI
+#define CONFIG_S5P_SDHCI
+#define CONFIG_DWMMC
+#define CONFIG_EXYNOS_DWMMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/* PWM */
+#define CONFIG_PWM
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_HASH
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+/* Thermal Management Unit */
+#define CONFIG_EXYNOS_TMU
+#define CONFIG_CMD_DTT
+#define CONFIG_TMU_CMD_DTT
+
+/* TPM */
+#define CONFIG_TPM
+#define CONFIG_CMD_TPM
+#define CONFIG_TPM_TIS_I2C
+#define CONFIG_TPM_TIS_I2C_BUS_NUMBER	3
+#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
+
+/* MMC SPL */
+#define CONFIG_SPL
+#define COPY_BL2_FNPTR_ADDR	0x02020030
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+/* specific .lds file */
+#define CONFIG_SPL_LDSCRIPT	"board/samsung/common/exynos-uboot-spl.lds"
+#define CONFIG_SPL_MAX_FOOTPRINT	(14 * 1024)
+
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_RD_LVL
+
+#define CONFIG_NR_DRAM_BANKS	8
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
+
+#define CONFIG_SYS_MONITOR_BASE	0x00000000
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_SYS_MMC_ENV_DEV		0
+
+#define CONFIG_SECURE_BL1_ONLY
+
+/* Secure FW size configuration */
+#ifdef CONFIG_SECURE_BL1_ONLY
+#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
+#else
+#define CONFIG_SEC_FW_SIZE 0
+#endif
+
+/* Configuration of BL1, BL2, ENV Blocks on mmc */
+#define CONFIG_RES_BLOCK_SIZE	(512)
+#define CONFIG_BL1_SIZE	(16 << 10) /*16 K reserved for BL1*/
+#define CONFIG_BL2_SIZE	(512UL << 10UL) /* 512 KB */
+#define CONFIG_ENV_SIZE	(16 << 10) /* 16 KB */
+
+#define CONFIG_BL1_OFFSET	(CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
+#define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
+#define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
+
+#define CONFIG_SPI_BOOTING
+#define EXYNOS_COPY_SPI_FNPTR_ADDR	0x02020058
+#define SPI_FLASH_UBOOT_POS	(CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_PART
+#define CONFIG_PARTITION_UUIDS
+
+/* I2C */
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_HARD_I2C
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_SPEED	100000		/* 100 Kbps */
+#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SLAVE    0x0
+#define CONFIG_I2C_EDID
+
+/* SPI */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+#define CONFIG_ENV_SPI_BASE	0x12D30000
+
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_EXYNOS_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SPI_FLASH_GIGADEVICE
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		50000000
+#define EXYNOS5_SPI_NUM_CONTROLLERS	5
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MODE	SPI_MODE_0
+#define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
+#define CONFIG_ENV_SPI_BUS	1
+#define CONFIG_ENV_SPI_MAX_HZ	50000000
+#endif
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+
+/* Ethernet Controllor Driver */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_BASE		0x5000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_ENV_SROM_BANK		1
+#endif /*CONFIG_CMD_NET*/
+
+/* Enable PXE Support */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PXE
+#define CONFIG_MENU
+#endif
+
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+
+/* SHA hashing */
+#define CONFIG_CMD_HASH
+#define CONFIG_HASH_VERIFY
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+
+/* Enable Time Command */
+#define CONFIG_CMD_TIME
+
+#define CONFIG_CMD_BOOTZ
+
+#endif	/* __CONFIG_H */
include/configs/exynos5250-dt.h +7 -279

334 lines not on this page · raw message

include/configs/smdk5420.h new file +50 -0

50 lines not on this page · raw message

Signature · 1 line
1.7.12.4
#13 lore raw

PATCH v12 11/11 SPL: EXYNOS: Prepare for variable size SPL support

In reply to Rajeshwari S Shinde

When variable size SPL is used, the BL1 expects the SPL to be encapsulated differently: instead of putting the checksum at a fixed offset in the SPL blob, prepend the blob with a header including the size and the checksum.

The enhancements include
- adding a command line option, '--vs' to indicate the need for the variable size encapsulation
- padding the fixed size encapsulated blob with 0xff instead of random memory contents
- do not silently truncate the input file, report error instead
- no need to explicitly closing files/freeing memory, this all happens on exit; removing cleanups it makes code clearer
- profuse commenting
- modify Makefile to allow enabling the new feature per board

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None.
Changes in V7:
- None.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- None
Changes in V11:
- Rebased on latest code.
Changes in V12:
- None

 include/configs/smdk5420.h |   6 ++
 spl/Makefile               |   7 +-
 tools/mkexynosspl.c        | 167 +++++++++++++++++++++++++++++++++------------
 3 files changed, 136 insertions(+), 44 deletions(-)
include/configs/smdk5420.h +6 -0
index 9eab7d6..447f8e5 100644
@@ -19,6 +19,8 @@
 
 #define CONFIG_ARCH_DEVICE_TREE		exynos5420
 
+#define CONFIG_VAR_SIZE_SPL
+
 #define CONFIG_SYS_SDRAM_BASE		0x20000000
 #define CONFIG_SYS_TEXT_BASE		0x23E00000
 
@@ -31,7 +33,11 @@
 /* select serial console configuration */
 #define CONFIG_SERIAL3			/* use SERIAL 3 */
 
+#ifdef CONFIG_VAR_SIZE_SPL
+#define CONFIG_SPL_TEXT_BASE		0x02024410
+#else
 #define CONFIG_SPL_TEXT_BASE	0x02024400
+#endif
 
 #define CONFIG_BOOTCOMMAND	"mmc read 20007000 451 2000; bootm 20007000"
 
spl/Makefile +6 -1
index 2a787af..0caa982 100644
@@ -166,8 +166,13 @@ endif
 all:	$(ALL-y)
 
 ifdef CONFIG_SAMSUNG
+ifdef CONFIG_VAR_SIZE_SPL
+VAR_SIZE_PARAM = --vs
+else
+VAR_SIZE_PARAM =
+endif
 $(obj)$(BOARD)-spl.bin: $(obj)u-boot-spl.bin
-	$(OBJTREE)/tools/mk$(BOARD)spl $< $@
+	$(OBJTREE)/tools/mk$(BOARD)spl $(VAR_SIZE_PARAM) $< $@
 endif
 
 $(obj)$(SPL_BIN).bin:	$(obj)$(SPL_BIN)
tools/mkexynosspl.c +124 -43

217 lines not on this page · raw message

Signature · 1 line
1.7.12.4