EXYNOS5420: Add SMDK5420 board support
Subsystems (2)
v13 cover EXYNOS5420: Add SMDK5420 board support
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Rajeshwari S Shinde (11):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
EXYNOS5420: Add power register structure.
EXYNOS5420: Add dmc and phy_control register structure
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support
arch/arm/cpu/armv7/exynos/clock.c | 279 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 ++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 60 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 ++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 764 ++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 +++++++- arch/arm/dts/exynos5.dtsi | 198 ++++++ arch/arm/dts/exynos5250.dtsi | 194 +----- arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 52 +- arch/arm/include/asm/arch-exynos/dmc.h | 177 ++++++ arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 408 ++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++ board/samsung/smdk5250/exynos5-dt.c | 350 +---------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 11 + board/samsung/smdk5420/smdk5420.c | 159 +++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 290 +++++++++ include/configs/exynos5250-dt.h | 284 +-------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 +++-- 34 files changed, 5187 insertions(+), 1314 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
Signature · 1 line
1.7.12.4
PATCH v13 1/11 EXYNOS5: Create a common board file
Create a common board.c file for all functions which are common across all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added check for the compilation of MAX77686 pmic.
Changes in V5:
- Moved board_eth_init and board_mmc_init in case of device tree support
Changes in V6:
- None.
Changes in V7:
- None
Changes in V8:
- None
Changes in V9:
- Reabsed on latest code.
Changes in V10:
- Corrected coding style nits.
Changes in V11:
-Rebased on latest u-boot-samsung tree
Changes in V12:
- None
Changes in V13:
- Rebased on latest u-boot-samsung tree
arch/arm/include/asm/arch-exynos/board.h | 17 ++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 409 +++++++++++++++++++++++++++++++ board/samsung/smdk5250/exynos5-dt.c | 350 +------------------------- board/samsung/smdk5250/smdk5250.c | 182 +------------- include/configs/exynos5250-dt.h | 2 + 6 files changed, 437 insertions(+), 527 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c
arch/arm/include/asm/arch-exynos/board.h new file +17 -0
@@ -0,0 +1,17 @@ +/* +* (C) Copyright 2013 Samsung Electronics +* Rajeshwari Shinde <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _EXYNOS_BOARD_H +#define _EXYNOS_BOARD_H + +/* +* Exynos baord specific changes for +* board_init +*/ +int exynos_init (void ); + +#endif /* EXYNOS_BOARD_H */
board/samsung/common/Makefile +4 -0
@@ -8,3 +8,7 @@ obj-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o obj-$(CONFIG_THOR_FUNCTION) += thor.o obj-$(CONFIG_CMD_USB_MASS_STORAGE) += ums.o + +ifndef CONFIG_SPL_BUILD +obj-$(CONFIG_BOARD_COMMON) += board.o +endif
board/samsung/common/board.c new file +409 -0
409 lines not on this page · raw message
board/samsung/smdk5250/exynos5-dt.c +2 -348
379 lines not on this page · raw message
board/samsung/smdk5250/smdk5250.c +3 -179
219 lines not on this page · raw message
include/configs/exynos5250-dt.h +2 -0
@@ -21,6 +21,8 @@#define CONFIG_ARCH_CPU_INIT #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_COMMON +#define CONFIG_ARCH_EARLY_INIT_R /* Enable fdt support for Exynos5250 */ #define CONFIG_OF_CONTROL
Signature · 1 line
1.7.12.4
PATCH v13 2/11 Exynos5420: Add base addresses for 5420
In reply to Rajeshwari S ShindeAdds base addresses of various IPs and controllers required for Exynos5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added base address for TZPC.
Changes in V5:
- None
Chnages in V6:
- Rebased on latest samsung mainline branch.
Changes in V7:
- Corrected the comments
Changes in V8:
- None
Changes in V9:
- None
Changes in V10:
- None
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/include/asm/arch-exynos/cpu.h | 49 +++++++++++++++++++++++++++++++++- 1 file changed, 48 insertions(+), 1 deletion(-)
arch/arm/include/asm/arch-exynos/cpu.h +48 -1
@@ -92,7 +92,7 @@#define EXYNOS4X12_USB_HOST_XHCI_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4X12_USB3PHY_BASE DEVICE_NOT_AVAILABLE -/* EXYNOS5 Common*/ +/* EXYNOS5 */ #define EXYNOS5_I2C_SPACING 0x10000#define EXYNOS5_AUDIOSS_BASE 0x03810000
@@ -130,6 +130,46 @@#define EXYNOS5_ADC_BASE DEVICE_NOT_AVAILABLE#define EXYNOS5_MODEM_BASE DEVICE_NOT_AVAILABLE +/* EXYNOS5420 */ +#define EXYNOS5420_AUDIOSS_BASE 0x03810000 +#define EXYNOS5420_GPIO_PART5_BASE 0x03860000 +#define EXYNOS5420_PRO_ID 0x10000000 +#define EXYNOS5420_CLOCK_BASE 0x10010000 +#define EXYNOS5420_POWER_BASE 0x10040000 +#define EXYNOS5420_SWRESET 0x10040400 +#define EXYNOS5420_SYSREG_BASE 0x10050000 +#define EXYNOS5420_TZPC_BASE 0x100E0000 +#define EXYNOS5420_WATCHDOG_BASE 0x101D0000 +#define EXYNOS5420_ACE_SFR_BASE 0x10830000 +#define EXYNOS5420_DMC_PHY_BASE 0x10C00000 +#define EXYNOS5420_DMC_CTRL_BASE 0x10C20000 +#define EXYNOS5420_DMC_TZASC0_BASE 0x10D40000 +#define EXYNOS5420_DMC_TZASC1_BASE 0x10D50000 +#define EXYNOS5420_USB_HOST_EHCI_BASE 0x12110000 +#define EXYNOS5420_MMC_BASE 0x12200000 +#define EXYNOS5420_SROMC_BASE 0x12250000 +#define EXYNOS5420_UART_BASE 0x12C00000 +#define EXYNOS5420_I2C_BASE 0x12C60000 +#define EXYNOS5420_I2C_8910_BASE 0x12E00000 +#define EXYNOS5420_SPI_BASE 0x12D20000 +#define EXYNOS5420_I2S_BASE 0x12D60000 +#define EXYNOS5420_PWMTIMER_BASE 0x12DD0000 +#define EXYNOS5420_SPI_ISP_BASE 0x131A0000 +#define EXYNOS5420_GPIO_PART2_BASE 0x13400000 +#define EXYNOS5420_GPIO_PART3_BASE 0x13410000 +#define EXYNOS5420_GPIO_PART4_BASE 0x14000000 +#define EXYNOS5420_GPIO_PART1_BASE 0x14010000 +#define EXYNOS5420_MIPI_DSIM_BASE 0x14500000 +#define EXYNOS5420_DP_BASE 0x145B0000 + +#define EXYNOS5420_USBPHY_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_USBOTG_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_FIMD_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_ADC_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_MODEM_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_USB3PHY_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_USB_HOST_XHCI_BASE DEVICE_NOT_AVAILABLE +#ifndef __ASSEMBLY__#include <asm/io.h> /* CPU detection macros */
@@ -163,6 +203,10 @@ static inline void s5p_set_cpu_id(void)/* Exynos5250 */ s5p_cpu_id =0x5250 ;break ; +case 0x420 : +/* Exynos5420 */ + s5p_cpu_id =0x5420 ; +break ; } }
@@ -190,6 +234,7 @@ static inline int __attribute__((no_instrument_function)) \ IS_EXYNOS_TYPE(exynos4210, 0x4210) IS_EXYNOS_TYPE(exynos4412, 0x4412) IS_EXYNOS_TYPE(exynos5250, 0x5250) +IS_EXYNOS_TYPE(exynos5420, 0x5420)#define SAMSUNG_BASE (device, base) \ static inline unsigned int __attribute__((no_instrument_function)) \
@@ -200,6 +245,8 @@ static inline unsigned int __attribute__((no_instrument_function)) \ return EXYNOS4X12_##base; \ return EXYNOS4_##base; \ } else if (cpu_is_exynos5()) { \ + if (proid_is_exynos5420()) \ + return EXYNOS5420_##base; \ return EXYNOS5_##base; \ } \ return 0; \
Signature · 1 line
1.7.12.4
PATCH v13 3/11 EXYNOS5420: Add power register structure.
In reply to Rajeshwari S ShindeAdd structure for power register for Exynos5420
---
Changes in V10:
- New patch
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++++++++ arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++++++++ 1 file changed, 837 insertions(+)
arch/arm/include/asm/arch-exynos/power.h +837 -0
@@ -831,6 +831,843 @@ struct exynos5_power {unsigned int cmu_reset_mau_option;unsigned char res163[0x24 ]; }; + +struct exynos5420_power { +unsigned int om_stat; +unsigned int lpi_mask0; +unsigned int lpi_mask1; +unsigned char res1[0x10 ]; +unsigned int rtc_clko_sel; +unsigned char res2[0x1e0 ]; +unsigned int central_seq_configuration; +unsigned int central_seq_status; +unsigned int central_seq_option; +unsigned char res3[0x14 ]; +unsigned int seq_transition0; +unsigned int seq_transition1; +unsigned int seq_transition2; +unsigned int seq_transition3; +unsigned int seq_transition4; +unsigned int seq_transition5; +unsigned int seq_transition6; +unsigned int seq_transition7; +unsigned int central_seq_coreblk_configuration; +unsigned int central_seq_coreblk_status; +unsigned int central_seq_coreblk_option; +unsigned char res4[0x14 ]; +unsigned int seq_coreblk_transition0; +unsigned int seq_coreblk_transition1; +unsigned int seq_coreblk_transition2; +unsigned int seq_coreblk_transition3; +unsigned int seq_coreblk_transition4; +unsigned int seq_coreblk_transition5; +unsigned int seq_coreblk_transition6; +unsigned int seq_coreblk_transition7; +unsigned char res5[0x180 ]; +unsigned int swreset; +unsigned int rst_stat; +unsigned int automatic_wdt_reset_disable; +unsigned int mask_wdt_reset_request; +unsigned int mask_wreset_request; +unsigned char res6[0xec ]; +unsigned int reset_sequencer_configuration; +unsigned int reset_sequencer_status; +unsigned int reset_sequencer_option; +unsigned char res7[0xf4 ]; +unsigned int wakeup_stat; +unsigned int eint_wakeup_mask; +unsigned int wakeup_mask; +unsigned int wakeup_interrupt; +unsigned char res8[0x10 ]; +unsigned int wakeup_stat_coreblk; +unsigned int eint_wakeup_mask_coreblk; +unsigned int wakeup_mask_coreblk; +unsigned int wakeup_interrupt_coreblk; +unsigned char res9[0xd0 ]; +unsigned int hdmi_phy_control; +unsigned int usbdev_phy_control; +unsigned int usbdev1_phy_control; +unsigned int usbhost_phy_control; +unsigned char res104[0x4 ]; +unsigned int mipi_phy0_control; +unsigned int mipi_phy1_control; +unsigned int mipi_phy2_control; +unsigned int adc_phy_control; +unsigned int mtcadc_phy_control; +unsigned int dptx_phy_control; +unsigned char res10[0xd4 ]; +unsigned int inform0; +unsigned int inform1; +unsigned int inform2; +unsigned int inform3; +unsigned int sysip_dat0; +unsigned int sysip_dat1; +unsigned int sysip_dat2; +unsigned int sysip_dat3; +unsigned char res11[0xe0 ]; +unsigned int pmu_spare0; +unsigned int pmu_spare1; +unsigned int pmu_spare2; +unsigned int pmu_spare3; +unsigned char res12[0x4 ]; +unsigned int cg_status0; +unsigned int cg_status1; +unsigned int cg_status2; +unsigned int cg_status3; +unsigned int cg_status4; +unsigned char res200[0x58 ]; +unsigned int irom_data_reg0; +unsigned int irom_data_reg1; +unsigned int irom_data_reg2; +unsigned int irom_data_reg3; +unsigned char res13[0x70 ]; +unsigned int pmu_debug; +unsigned char res14[0x5fc ]; +unsigned int arm_core0_sys_pwr_reg; +unsigned char res500[0xc ]; +unsigned int arm_core1_sys_pwr_reg; +unsigned char res501[0xc ]; +unsigned int arm_core2_sys_pwr_reg; +unsigned char res502[0xc ]; +unsigned int arm_core3_sys_pwr_reg; +unsigned char res503[0xc ]; +unsigned int kfc_core0_sys_pwr_reg; +unsigned char res504[0xc ]; +unsigned int kfc_core1_sys_pwr_reg; +unsigned char res505[0xc ]; +unsigned int kfc_core2_sys_pwr_reg; +unsigned char res506[0xc ]; +unsigned int kfc_core3_sys_pwr_reg; +unsigned char res507[0x1c ]; +unsigned int isp_arm_sys_pwr_reg; +unsigned char res18[0xc ]; +unsigned int arm_common_sys_pwr_reg; +unsigned char res508[0xc ]; +unsigned int kfc_common_sys_pwr_reg; +unsigned char res19[0xc ]; +unsigned int arm_l2_sys_pwr_reg; +unsigned char res509[0xc ]; +unsigned int kfc_l2_sys_pwr_reg; +unsigned char res20[0xc ]; +unsigned int cmu_cpu_aclkstop_sys_pwr_reg; +unsigned int cmu_cpu_sclkstop_sys_pwr_reg; +unsigned char res510[0x8 ]; +unsigned int cmu_kfc_aclkstop_sys_pwr_reg; +unsigned char res511[0xc ]; +unsigned int cmu_aclkstop_sys_pwr_reg; +unsigned int cmu_sclkstop_sys_pwr_reg; +unsigned char res21[0x4 ]; +unsigned int cmu_reset_sys_pwr_reg; +unsigned char res22[0x10 ]; +unsigned int cmu_aclkstop_coreblk_sys_pwr_reg; +unsigned int cmu_sclkstop_coreblk_sys_pwr_reg; +unsigned char res23[0x4 ]; +unsigned int cmu_reset_coreblk_sys_pwr_reg; +unsigned int dram_freq_down_sys_pwr_reg; +unsigned int ddrphy_dlloff_sys_pwr_reg; +unsigned int ddrphy_dlllock_sys_pwr_reg; +unsigned char res25[0x4 ]; +unsigned int apll_sysclk_sys_pwr_reg; +unsigned int mpll_sysclk_sys_pwr_reg; +unsigned int vpll_sysclk_sys_pwr_reg; +unsigned int epll_sysclk_sys_pwr_reg; +unsigned int bpll_sysclk_sys_pwr_reg; +unsigned int cpll_sysclk_sys_pwr_reg; +unsigned int dpll_sysclk_sys_pwr_reg; +unsigned int ipll_sysclk_sys_pwr_reg; +unsigned int kpll_sysclk_sys_pwr_reg; +unsigned int mplluser_sysclk_sys_pwr_reg; +unsigned char res512[0x8 ]; +unsigned int bplluser_sysclk_sys_pwr_reg; +unsigned int rpll_sysclk_sys_pwr_reg; +unsigned int spll_sysclk_sys_pwr_reg; +unsigned char res26[0x4 ]; +unsigned int top_bus_sys_pwr_reg; +unsigned int top_retention_sys_pwr_reg; +unsigned int top_pwr_sys_pwr_reg; +unsigned char res29[0x4 ]; +unsigned int top_bus_coreblk_sys_pwr_reg; +unsigned int top_retention_coreblk_sys_pwr_reg; +unsigned int top_pwr_coreblk_sys_pwr_reg; +unsigned char res30[0x4 ]; +unsigned int logic_reset_sys_pwr_reg; +unsigned int oscclk_gate_sys_pwr_reg; +unsigned char res31[0x8 ]; +unsigned int logic_reset_coreblk_sys_pwr_reg; +unsigned int oscclk_gate_coreblk_sys_pwr_reg; +unsigned int intram_mem_sys_pwr_reg; +unsigned int introm_mem_sys_pwr_reg; +unsigned char res32[0x44 ]; +unsigned int pad_retention_mau_sys_pwr_reg; +unsigned int pad_retention_jtag_sys_pwr_reg; +unsigned char res36[0x4 ]; +unsigned int pad_retention_dram_sys_pwr_reg; +unsigned int pad_retention_uart_sys_pwr_reg; +unsigned int pad_retention_mmca_sys_pwr_reg; +unsigned int pad_retention_mmcb_sys_pwr_reg; +unsigned int pad_retention_mmcc_sys_pwr_reg; +unsigned int pad_retention_hsi_sys_pwr_reg; +unsigned int pad_retention_ebia_sys_pwr_reg; +unsigned int pad_retention_ebib_sys_pwr_reg; +unsigned int pad_retention_spi_sys_pwr_reg; +unsigned int pad_retention_dram_coreblk_sys_pwr_reg; +unsigned char res28[0x8 ]; +unsigned int pad_isolation_sys_pwr_reg; +unsigned char res37[0xc ]; +unsigned int pad_isolation_coreblk_sys_pwr_reg; +unsigned char res38[0xc ]; +unsigned int pad_alv_sel_sys_pwr_reg; +unsigned char res39[0x1c ]; +unsigned int xusbxti_sys_pwr_reg; +unsigned int xxti_sys_pwr_reg; +unsigned char res40[0x38 ]; +unsigned int ext_regulator_sys_pwr_reg; +unsigned char res41[0x3c ]; +unsigned int gpio_mode_sys_pwr_reg; +unsigned char res42[0x1c ]; +unsigned int gpio_mode_coreblk_sys_pwr_reg; +unsigned char res43[0x1c ]; +unsigned int gpio_mode_mau_sys_pwr_reg; +unsigned int top_asb_reset_sys_pwr_reg; +unsigned int top_asb_isolation_sys_pwr_reg; +unsigned char res44[0xb4 ]; +unsigned int gscl_sys_pwr_reg; +unsigned int isp_sys_pwr_reg; +unsigned int mfc_sys_pwr_reg; +unsigned int g3d_sys_pwr_reg; +unsigned int disp1_sys_pwr_reg; +unsigned int mau_sys_pwr_reg; +unsigned int g2d_sys_pwr_reg; +unsigned int msc_sys_pwr_reg; +unsigned int fsys_sys_pwr_reg; +unsigned int fsys2_sys_pwr_reg; +unsigned int psgen_sys_pwr_reg; +unsigned int peric_sys_pwr_reg; +unsigned int wcore_sys_pwr_reg; +unsigned char res46[0x4c ]; +unsigned int cmu_clkstop_gscl_sys_pwr_reg; +unsigned int cmu_clkstop_isp_sys_pwr_reg; +unsigned int cmu_clkstop_mfc_sys_pwr_reg; +unsigned int cmu_clkstop_g3d_sys_pwr_reg; +unsigned int cmu_clkstop_disp1_sys_pwr_reg; +unsigned int cmu_clkstop_mau_sys_pwr_reg; +unsigned int cmu_clkstop_g2d_sys_pwr_reg; +unsigned int cmu_clkstop_msc_sys_pwr_reg; +unsigned int cmu_clkstop_fsys_sys_pwr_reg; +unsigned int cmu_clkstop_fsys2_sys_pwr_reg; +unsigned int cmu_clkstop_psgen_sys_pwr_reg; +unsigned int cmu_clkstop_peric_sys_pwr_reg; +unsigned int cmu_clkstop_wcore_sys_pwr_reg; +unsigned char res48[0x8 ]; +unsigned int cmu_sysclk_toppwr_sys_pwr_reg; +unsigned int cmu_sysclk_gscl_sys_pwr_reg; +unsigned int cmu_sysclk_isp_sys_pwr_reg; +unsigned int cmu_sysclk_mfc_sys_pwr_reg; +unsigned int cmu_sysclk_g3d_sys_pwr_reg; +unsigned int cmu_sysclk_disp1_sys_pwr_reg; +unsigned int cmu_sysclk_mau_sys_pwr_reg; +unsigned int cmu_sysclk_g2d_sys_pwr_reg; +unsigned int cmu_sysclk_msc_sys_pwr_reg; +unsigned int cmu_sysclk_fsys_sys_pwr_reg; +unsigned int cmu_sysclk_fsys2_sys_pwr_reg; +unsigned int cmu_sysclk_psgen_sys_pwr_reg; +unsigned int cmu_sysclk_peric_sys_pwr_reg; +unsigned int cmu_sysclk_wcore_sys_pwr_reg; +unsigned int cmu_sysclk_coreblk_toppwr_sys_pwr_reg; +unsigned char res50[0x78 ]; +unsigned int cmu_reset_fsys2_sys_pwr_reg; +unsigned int cmu_reset_psgen_sys_pwr_reg; +unsigned int cmu_reset_peric_sys_pwr_reg; +unsigned int cmu_reset_wcore_sys_pwr_reg; +unsigned int cmu_reset_gscl_sys_pwr_reg; +unsigned int cmu_reset_isp_sys_pwr_reg; +unsigned int cmu_reset_mfc_sys_pwr_reg; +unsigned int cmu_reset_g3d_sys_pwr_reg; +unsigned int cmu_reset_disp1_sys_pwr_reg; +unsigned int cmu_reset_mau_sys_pwr_reg; +unsigned int cmu_reset_g2d_sys_pwr_reg; +unsigned int cmu_reset_msc_sys_pwr_reg; +unsigned int cmu_reset_fsys_sys_pwr_reg; +unsigned char res52[0xa5c ]; +unsigned int arm_core0_configuration; +unsigned int arm_core0_status; +unsigned int arm_core0_option; +unsigned char res53[0x14 ]; +unsigned int dis_irq_arm_core0_local_configuration; +unsigned int dis_irq_arm_core0_local_status; +unsigned int dis_irq_arm_core0_local_option; +unsigned char res54[0x14 ]; +unsigned int dis_irq_arm_core0_central_configuration; +unsigned int dis_irq_arm_core0_central_status; +unsigned int dis_irq_arm_core0_central_option; +unsigned char res55[0x34 ]; +unsigned int arm_core1_configuration; +unsigned int arm_core1_status; +unsigned int arm_core1_option; +unsigned char res56[0x14 ]; +unsigned int dis_irq_arm_core1_local_configuration; +unsigned int dis_irq_arm_core1_local_status; +unsigned int dis_irq_arm_core1_local_option; +unsigned char res57[0x14 ]; +unsigned int dis_irq_arm_core1_central_configuration; +unsigned int dis_irq_arm_core1_central_status; +unsigned int dis_irq_arm_core1_central_option; +unsigned char res600[0x34 ]; +unsigned int arm_core2_configuration; +unsigned int arm_core2_status; +unsigned int arm_core2_option; +unsigned char res601[0x14 ]; +unsigned int dis_irq_arm_core2_local_configuration; +unsigned int dis_irq_arm_core2_local_status; +unsigned int dis_irq_arm_core2_local_option; +unsigned char res602[0x14 ]; +unsigned int dis_irq_arm_core2_central_configuration; +unsigned int dis_irq_arm_core2_central_status; +unsigned int dis_irq_arm_core2_central_option; +unsigned char res603[0x34 ]; +unsigned int arm_core3_configuration; +unsigned int arm_core3_status; +unsigned int arm_core3_option; +unsigned char res900[0x14 ]; +unsigned int dis_irq_arm_core3_local_configuration; +unsigned int dis_irq_arm_core3_local_status; +unsigned int dis_irq_arm_core3_local_option; +unsigned char res901[0x14 ]; +unsigned int dis_irq_arm_core3_central_configuration; +unsigned int dis_irq_arm_core3_central_status; +unsigned int dis_irq_arm_core3_central_option; +unsigned char res604[0x34 ]; +unsigned int kfc_core0_configuration; +unsigned int kfc_core0_status; +unsigned int kfc_core0_option; +unsigned char res605[0x14 ]; +unsigned int dis_irq_kfc_core0_local_configuration; +unsigned int dis_irq_kfc_core0_local_status; +unsigned int dis_irq_kfc_core0_local_option; +unsigned char res606[0x14 ]; +unsigned int dis_irq_kfc_core0_central_configuration; +unsigned int dis_irq_kfc_core0_central_status; +unsigned int dis_irq_kfc_core0_central_option; +unsigned char res607[0x34 ]; +unsigned int kfc_core1_configuration; +unsigned int kfc_core1_status; +unsigned int kfc_core1_option; +unsigned char res608[0x14 ]; +unsigned int dis_irq_kfc_core1_local_configuration; +unsigned int dis_irq_kfc_core1_local_status; +unsigned int dis_irq_kfc_core1_local_option; +unsigned char res609[0x14 ]; +unsigned int dis_irq_kfc_core1_central_configuration; +unsigned int dis_irq_kfc_core1_central_status; +unsigned int dis_irq_kfc_core1_central_option; +unsigned char res610[0x34 ]; +unsigned int kfc_core2_configuration; +unsigned int kfc_core2_status; +unsigned int kfc_core2_option; +unsigned char res611[0x14 ]; +unsigned int dis_irq_kfc_core2_local_configuration; +unsigned int dis_irq_kfc_core2_local_status; +unsigned int dis_irq_kfc_core2_local_option; +unsigned char res612[0x14 ]; +unsigned int dis_irq_kfc_core2_central_configuration; +unsigned int dis_irq_kfc_core2_central_status; +unsigned int dis_irq_kfc_core2_central_option; +unsigned char res613[0x34 ]; +unsigned int kfc_core3_configuration; +unsigned int kfc_core3_status; +unsigned int kfc_core3_option; +unsigned char res614[0x14 ]; +unsigned int dis_irq_kfc_core3_local_configuration; +unsigned int dis_irq_kfc_core3_local_status; +unsigned int dis_irq_kfc_core3_local_option; +unsigned char res615[0x14 ]; +unsigned int dis_irq_kfc_core3_central_configuration; +unsigned int dis_irq_kfc_core3_central_status; +unsigned int dis_irq_kfc_core3_central_option; +unsigned char res61[0xb4 ]; +unsigned int isp_arm_configuration; +unsigned int isp_arm_status; +unsigned int isp_arm_option; +unsigned char res62[0x14 ]; +unsigned int dis_irq_isp_arm_local_configuration; +unsigned int dis_irq_isp_arm_local_status; +unsigned int dis_irq_isp_arm_local_option; +unsigned char res63[0x14 ]; +unsigned int dis_irq_isp_arm_central_configuration; +unsigned int dis_irq_isp_arm_central_status; +unsigned int dis_irq_isp_arm_central_option; +unsigned char res64[0x34 ]; +unsigned int arm_common_configuration; +unsigned int arm_common_status; +unsigned int arm_common_option; +unsigned char res616[0x74 ]; +unsigned int kfc_common_configuration; +unsigned int kfc_common_status; +unsigned int kfc_common_option; +unsigned char res65[0x74 ]; +unsigned int arm_l2_configuration; +unsigned int arm_l2_status; +unsigned int arm_l2_option; +unsigned char res617[0x74 ]; +unsigned int kfc_l2_configuration; +unsigned int kfc_l2_status; +unsigned int kfc_l2_option; +unsigned char res66[0x74 ]; +unsigned int cmu_cpu_aclkstop_configuration; +unsigned int cmu_cpu_aclkstop_status; +unsigned int cmu_cpu_aclkstop_option; +unsigned char res67[0x14 ]; +unsigned int cmu_cpu_sclkstop_configuration; +unsigned int cmu_cpu_sclkstop_status; +unsigned int cmu_cpu_sclkstop_option; +unsigned char res618[0x4 ]; +unsigned int cmu_kfc_aclkstop_configuration; +unsigned int cmu_kfc_aclkstop_status; +unsigned int cmu_kfc_aclkstop_option; +unsigned char res619[0xc4 ]; +unsigned int cmu_aclkstop_configuration; +unsigned int cmu_aclkstop_status; +unsigned int cmu_aclkstop_option; +unsigned char res620[0x14 ]; +unsigned int cmu_sclkstop_configuration; +unsigned int cmu_sclkstop_status; +unsigned int cmu_sclkstop_option; +unsigned char res68[0x34 ]; +unsigned int cmu_reset_configuration; +unsigned int cmu_reset_status; +unsigned int cmu_reset_option; +unsigned char res69[0x94 ]; +unsigned int cmu_aclkstop_coreblk_configuration; +unsigned int cmu_aclkstop_coreblk_status; +unsigned int cmu_aclkstop_coreblk_option; +unsigned char res70[0x14 ]; +unsigned int cmu_sclkstop_coreblk_configuration; +unsigned int cmu_sclkstop_coreblk_status; +unsigned int cmu_sclkstop_coreblk_option; +unsigned char res71[0x34 ]; +unsigned int cmu_reset_coreblk_configuration; +unsigned int cmu_reset_coreblk_status; +unsigned int cmu_reset_coreblk_option; +unsigned char res621[0x14 ]; +unsigned int dram_freq_down_configuration; +unsigned int dram_freq_down_status; +unsigned int dram_freq_down_option; +unsigned char res622[0x14 ]; +unsigned int ddrphy_dlloff_configuration; +unsigned int ddrphy_dlloff_status; +unsigned int ddrphy_dlloff_option; +unsigned char res72[0x14 ]; +unsigned int ddrphy_dlllock_configuration; +unsigned int ddrphy_dlllock_status; +unsigned int ddrphy_dlllock_option; +unsigned char res73[0x34 ]; +unsigned int apll_sysclk_configuration; +unsigned int apll_sysclk_status; +unsigned int apll_sysclk_option; +unsigned char res74[0x18 ]; +unsigned int mpll_sysclk_status; +unsigned int mpll_sysclk_option; +unsigned char res75[0x14 ]; +unsigned int vpll_sysclk_configuration; +unsigned int vpll_sysclk_status; +unsigned int vpll_sysclk_option; +unsigned char res76[0x14 ]; +unsigned int epll_sysclk_configuration; +unsigned int epll_sysclk_status; +unsigned int epll_sysclk_option; +unsigned char res77[0x14 ]; +unsigned int bpll_sysclk_configuration; +unsigned int bpll_sysclk_status; +unsigned int bpll_sysclk_option; +unsigned char res78[0x14 ]; +unsigned int cpll_sysclk_configuration; +unsigned int cpll_sysclk_status; +unsigned int cpll_sysclk_option; +unsigned char res79[0x14 ]; +unsigned int dpll_sysclk_configuration; +unsigned int dpll_sysclk_status; +unsigned int dpll_sysclk_option; +unsigned char res700[0x14 ]; +unsigned int ipll_sysclk_configuration; +unsigned int ipll_sysclk_status; +unsigned int ipll_sysclk_option; +unsigned char res903[0x14 ]; +unsigned int kpll_sysclk_configuration; +unsigned int kpll_sysclk_status; +unsigned int kpll_sysclk_option; +unsigned char res80[0x14 ]; +unsigned int mplluser_sysclk_configuration; +unsigned int mplluser_sysclk_status; +unsigned int mplluser_sysclk_option; +unsigned char res81[0x54 ]; +unsigned int bplluser_sysclk_configuration; +unsigned int bplluser_sysclk_status; +unsigned int bplluser_sysclk_option; +unsigned char res701[0x14 ]; +unsigned int rplluser_sysclk_configuration; +unsigned int rplluser_sysclk_status; +unsigned int rplluser_sysclk_option; +unsigned char res702[0x14 ]; +unsigned int splluser_sysclk_configuration; +unsigned int splluser_sysclk_status; +unsigned int splluser_sysclk_option; +unsigned char res82[0x34 ]; +unsigned int top_bus_configuration; +unsigned int top_bus_status; +unsigned int top_bus_option; +unsigned char res83[0x14 ]; +unsigned int top_retention_configuration; +unsigned int top_retention_status; +unsigned int top_retention_option; +unsigned char res84[0x14 ]; +unsigned int top_pwr_configuration; +unsigned int top_pwr_status; +unsigned int top_pwr_option; +unsigned char res85[0x34 ]; +unsigned int top_bus_coreblk_configuration; +unsigned int top_bus_coreblk_status; +unsigned int top_bus_coreblk_option; +unsigned char res86[0x14 ]; +unsigned int top_retention_coreblk_configuration; +unsigned int top_retention_coreblk_status; +unsigned int top_retention_coreblk_option; +unsigned char res87[0x14 ]; +unsigned int top_pwr_coreblk_configuration; +unsigned int top_pwr_coreblk_status; +unsigned int top_pwr_coreblk_option; +unsigned char res88[0x34 ]; +unsigned int logic_reset_configuration; +unsigned int logic_reset_status; +unsigned int logic_reset_option; +unsigned char res89[0x14 ]; +unsigned int oscclk_gate_configuration; +unsigned int oscclk_gate_status; +unsigned int oscclk_gate_option; +unsigned char res90[0x54 ]; +unsigned int logic_reset_coreblk_configuration; +unsigned int logic_reset_coreblk_status; +unsigned int logic_reset_coreblk_option; +unsigned char res91[0x14 ]; +unsigned int oscclk_gate_coreblk_configuration; +unsigned int oscclk_gate_coreblk_status; +unsigned int oscclk_gate_coreblk_option; +unsigned char res99[0x174 ]; +unsigned int intram_mem_configuration; +unsigned int intram_mem_status; +unsigned int intram_mem_option; +unsigned char res100[0x14 ]; +unsigned int introm_mem_configuration; +unsigned int introm_mem_status; +unsigned int introm_mem_option; +unsigned char res101[0xb4 ]; +unsigned int pad_retention_dram_configuration; +unsigned int pad_retention_dram_status; +unsigned int pad_retention_dram_option; +unsigned char res106[0x14 ]; +unsigned int pad_retention_mau_configuration; +unsigned int pad_retention_mau_status; +unsigned int pad_retention_mau_option; +unsigned char res107[0x14 ]; +unsigned int pad_retention_jtag_configuration; +unsigned int pad_retention_jtag_status; +unsigned int pad_retention_jtag_option; +unsigned char res92[0x74 ]; +unsigned int pad_retention_dram_configuration_2; +unsigned int pad_retention_dram_status_2; +unsigned int pad_retention_dram_option_2; +unsigned char res111[0x14 ]; +unsigned int pad_retention_uart_configuration; +unsigned int pad_retention_uart_status; +unsigned int pad_retention_uart_option; +unsigned char res112[0x14 ]; +unsigned int pad_retention_mmca_configuration; +unsigned int pad_retention_mmca_status; +unsigned int pad_retention_mmca_option; +unsigned char res113[0x14 ]; +unsigned int pad_retention_mmcb_configuration; +unsigned int pad_retention_mmcb_status; +unsigned int pad_retention_mmcb_option; +unsigned char res93[0x14 ]; +unsigned int pad_retention_mmcc_configuration; +unsigned int pad_retention_mmcc_status; +unsigned int pad_retention_mmcc_option; +unsigned char res94[0x14 ]; +unsigned int pad_retention_hsi_configuration; +unsigned int pad_retention_hsi_status; +unsigned int pad_retention_hsi_option; +unsigned char res114[0x14 ]; +unsigned int pad_retention_ebia_configuration; +unsigned int pad_retention_ebia_status; +unsigned int pad_retention_ebia_option; +unsigned char res115[0x14 ]; +unsigned int pad_retention_ebib_configuration; +unsigned int pad_retention_ebib_status; +unsigned int pad_retention_ebib_option; +unsigned char res116[0x14 ]; +unsigned int pad_retention_spi_configuration; +unsigned int pad_retention_spi_status; +unsigned int pad_retention_spi_option; +unsigned char res117[0x14 ]; +unsigned int pad_retention_dram_coreblk_configuration; +unsigned int pad_retention_dram_coreblk_status; +unsigned int pad_retention_dram_coreblk_option; +unsigned char res118[0x14 ]; +unsigned int pad_isolation_configuration; +unsigned int pad_isolation_status; +unsigned int pad_isolation_option; +unsigned char res119[0x74 ]; +unsigned int pad_isolation_coreblk_configuration; +unsigned int pad_isolation_coreblk_status; +unsigned int pad_isolation_coreblk_option; +unsigned char res120[0x74 ]; +unsigned int pad_alv_sel_configuration; +unsigned int pad_alv_sel_status; +unsigned int pad_alv_sel_option0; +unsigned int ps_hold_control; +unsigned char res130[0xf0 ]; +unsigned int xusbxti_configuration; +unsigned int xusbxti_status; +unsigned int xusbxti_option; +unsigned char res910[0x10 ]; +unsigned int xusbxti_duration3; +unsigned int xxti_configuration; +unsigned int xxti_status; +unsigned int xxti_option; +unsigned char res131[0x10 ]; +unsigned int xxti_duration3; +unsigned char res132[0x1c0 ]; +unsigned int ext_regulator_configuration; +unsigned int ext_regulator_status; +unsigned int ext_regulator_option; +unsigned char res133[0x10 ]; +unsigned int ext_regulator_duration3; +unsigned char res134[0x1e0 ]; +unsigned int gpio_mode_configuration; +unsigned int gpio_mode_status; +unsigned int gpio_mode_option; +unsigned char res135[0xf4 ]; +unsigned int gpio_mode_coreblk_configuration; +unsigned int gpio_mode_coreblk_status; +unsigned int gpio_mode_coreblk_option; +unsigned char res136[0xd4 ]; +unsigned int gpio_mode_mau_configuration; +unsigned int gpio_mode_mau_status; +unsigned int gpio_mode_mau_option; +unsigned char res137[0x14 ]; +unsigned int top_asb_reset_configuration; +unsigned int top_asb_reset_status; +unsigned int top_asb_reset_option; +unsigned char res138[0x14 ]; +unsigned int top_asb_isolation_configuration; +unsigned int top_asb_isolation_status; +unsigned int top_asb_isolation_option; +unsigned char res139[0x5d4 ]; +unsigned int gscl_configuration; +unsigned int gscl_status; +unsigned int gscl_option; +unsigned char res140[0x14 ]; +unsigned int isp_configuration; +unsigned int isp_status; +unsigned int isp_option; +unsigned char res141[0x34 ]; +unsigned int mfc_configuration; +unsigned int mfc_status; +unsigned int mfc_option; +unsigned char res142[0x14 ]; +unsigned int g3d_configuration; +unsigned int g3d_status; +unsigned int g3d_option; +unsigned char res143[0x34 ]; +unsigned int disp1_configuration; +unsigned int disp1_status; +unsigned int disp1_option; +unsigned char res144[0x14 ]; +unsigned int mau_configuration; +unsigned int mau_status; +unsigned int mau_option; +unsigned char res800[0x14 ]; +unsigned int g2d_configuration; +unsigned int g2d_status; +unsigned int g2d_option; +unsigned char res801[0x14 ]; +unsigned int msc_configuration; +unsigned int msc_status; +unsigned int msc_option; +unsigned char res802[0x14 ]; +unsigned int fsys_configuration; +unsigned int fsys_status; +unsigned int fsys_option; +unsigned char res803[0x14 ]; +unsigned int fsys2_configuration; +unsigned int fsys2_status; +unsigned int fsys2_option; +unsigned char res804[0x14 ]; +unsigned int psgen_configuration; +unsigned int psgen_status; +unsigned int psgen_option; +unsigned char res805[0x14 ]; +unsigned int peric_configuration; +unsigned int peric_status; +unsigned int peric_option; +unsigned char res806[0x14 ]; +unsigned int wcore_configuration; +unsigned int wcore_status; +unsigned int wcore_option; +unsigned char res145[0x234 ]; +unsigned int cmu_clkstop_gscl_configuration; +unsigned int cmu_clkstop_gscl_status; +unsigned int cmu_clkstop_gscl_option; +unsigned char res146[0x14 ]; +unsigned int cmu_clkstop_isp_configuration; +unsigned int cmu_clkstop_isp_status; +unsigned int cmu_clkstop_isp_option; +unsigned char res147[0x34 ]; +unsigned int cmu_clkstop_mfc_configuration; +unsigned int cmu_clkstop_mfc_status; +unsigned int cmu_clkstop_mfc_option; +unsigned char res148[0x14 ]; +unsigned int cmu_clkstop_g3d_configuration; +unsigned int cmu_clkstop_g3d_status; +unsigned int cmu_clkstop_g3d_option; +unsigned char res149[0x34 ]; +unsigned int cmu_clkstop_disp1_configuration; +unsigned int cmu_clkstop_disp1_status; +unsigned int cmu_clkstop_disp1_option; +unsigned char res150[0x14 ]; +unsigned int cmu_clkstop_mau_configuration; +unsigned int cmu_clkstop_mau_status; +unsigned int cmu_clkstop_mau_option; +unsigned char res807[0x14 ]; +unsigned int cmu_clkstop_g2d_configuration; +unsigned int cmu_clkstop_g2d_status; +unsigned int cmu_clkstop_g2d_option; +unsigned char res808[0x14 ]; +unsigned int cmu_clkstop_msc_configuration; +unsigned int cmu_clkstop_msc_status; +unsigned int cmu_clkstop_msc_option; +unsigned char res809[0x14 ]; +unsigned int cmu_clkstop_fsys_configuration; +unsigned int cmu_clkstop_fsys_status; +unsigned int cmu_clkstop_fsys_option; +unsigned char res810[0x14 ]; +unsigned int cmu_clkstop_fsys2_configuration; +unsigned int cmu_clkstop_fsys2_status; +unsigned int cmu_clkstop_fsys2_option; +unsigned char res811[0x14 ]; +unsigned int cmu_clkstop_psgen_configuration; +unsigned int cmu_clkstop_psgen_status; +unsigned int cmu_clkstop_psgen_option; +unsigned char res812[0x14 ]; +unsigned int cmu_clkstop_peric_configuration; +unsigned int cmu_clkstop_peric_status; +unsigned int cmu_clkstop_peric_option; +unsigned char res813[0x14 ]; +unsigned int cmu_clkstop_wcore_configuration; +unsigned int cmu_clkstop_wcore_status; +unsigned int cmu_clkstop_wcore_option; +unsigned char res151[0x14 ]; +unsigned int cmu_sysclk_toppwr_configuration; +unsigned int cmu_sysclk_toppwr_status; +unsigned int cmu_sysclk_toppwr_option; +unsigned char res920[0x18 ]; +unsigned int cmu_sysclk_gscl_status; +unsigned int cmu_sysclk_gscl_option; +unsigned char res152[0x18 ]; +unsigned int cmu_sysclk_isp_status; +unsigned int cmu_sysclk_isp_option; +unsigned char res153[0x38 ]; +unsigned int cmu_sysclk_mfc_status; +unsigned int cmu_sysclk_mfc_option; +unsigned char res154[0x18 ]; +unsigned int cmu_sysclk_g3d_status; +unsigned int cmu_sysclk_g3d_option; +unsigned char res155[0x38 ]; +unsigned int cmu_sysclk_disp1_status; +unsigned int cmu_sysclk_disp1_option; +unsigned char res156[0x18 ]; +unsigned int cmu_sysclk_mau_status; +unsigned int cmu_sysclk_mau_option; +unsigned char res814[0x18 ]; +unsigned int cmu_sysclk_g2d_status; +unsigned int cmu_sysclk_g2d_option; +unsigned char res815[0x18 ]; +unsigned int cmu_sysclk_msc_status; +unsigned int cmu_sysclk_msc_option; +unsigned char res922[0x18 ]; +unsigned int cmu_sysclk_fsys_status; +unsigned int cmu_sysclk_fsys_option; +unsigned char res816[0x18 ]; +unsigned int cmu_sysclk_fsys2_status; +unsigned int cmu_sysclk_fsys2_option; +unsigned char res817[0x18 ]; +unsigned int cmu_sysclk_psgen_status; +unsigned int cmu_sysclk_psgen_option; +unsigned char res950[0x18 ]; +unsigned int cmu_sysclk_peric_status; +unsigned int cmu_sysclk_peric_option; +unsigned char res818[0x18 ]; +unsigned int cmu_sysclk_wcore_status; +unsigned int cmu_sysclk_wcore_option; +unsigned char res819[0x18 ]; +unsigned int cmu_sysclk_coreblk_toppwr_status; +unsigned int cmu_sysclk_coreblk_toppwr_option; +unsigned char res157[0x414 ]; +unsigned int cmu_reset_gscl_configuration; +unsigned int cmu_reset_gscl_status; +unsigned int cmu_reset_gscl_option; +unsigned char res158[0x14 ]; +unsigned int cmu_reset_isp_configuration; +unsigned int cmu_reset_isp_status; +unsigned int cmu_reset_isp_option; +unsigned char res159[0x34 ]; +unsigned int cmu_reset_mfc_configuration; +unsigned int cmu_reset_mfc_status; +unsigned int cmu_reset_mfc_option; +unsigned char res160[0x14 ]; +unsigned int cmu_reset_g3d_configuration; +unsigned int cmu_reset_g3d_status; +unsigned int cmu_reset_g3d_option; +unsigned char res161[0x34 ]; +unsigned int cmu_reset_disp1_configuration; +unsigned int cmu_reset_disp1_status; +unsigned int cmu_reset_disp1_option; +unsigned char res162[0x14 ]; +unsigned int cmu_reset_mau_configuration; +unsigned int cmu_reset_mau_status; +unsigned int cmu_reset_mau_option; +unsigned char res163[0x14 ]; +unsigned int version_info; +unsigned int i2s_bypass; +unsigned int kfc_swreset_mask_from_eagle; +unsigned char res164[0xf4 ]; +unsigned int cmu_reset_g2d_configuration; +unsigned int cmu_reset_g2d_status; +unsigned int cmu_reset_g2d_option; +unsigned char res165[0x14 ]; +unsigned int cmu_reset_msc_configuration; +unsigned int cmu_reset_msc_status; +unsigned int cmu_reset_msc_option; +unsigned char res166[0x14 ]; +unsigned int cmu_reset_fsys_configuration; +unsigned int cmu_reset_fsys_status; +unsigned int cmu_reset_fsys_option; +unsigned char res167[0x14 ]; +unsigned int cmu_reset_fsys2_configuration; +unsigned int cmu_reset_fsys2_status; +unsigned int cmu_reset_fsys2_option; +unsigned char res168[0x14 ]; +unsigned int cmu_reset_psgen_configuration; +unsigned int cmu_reset_psgen_status; +unsigned int cmu_reset_psgen_option; +unsigned char res169[0x14 ]; +unsigned int cmu_reset_peric_configuration; +unsigned int cmu_reset_peric_status; +unsigned int cmu_reset_peric_option; +unsigned char res170[0x14 ]; +unsigned int cmu_reset_wcore_configuration; +unsigned int cmu_reset_wcore_status; +unsigned int cmu_reset_wcore_option; +};#endif /* __ASSEMBLY__ */ void set_mipi_phy_ctrl (unsigned int dev_index,unsigned int enable);
Signature · 1 line
1.7.12.4
PATCH v13 4/11 EXYNOS5420: Add dmc and phy_control register structure
In reply to Rajeshwari S ShindeAdd dmc and phy_control register structure for 5420.
---
Changes in V10:
- New patch
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/include/asm/arch-exynos/dmc.h | 167 +++++++++++++++++++++++++++++++++ 1 file changed, 167 insertions(+)
arch/arm/include/asm/arch-exynos/dmc.h +167 -0
@@ -205,6 +205,127 @@ struct exynos5_dmc {unsigned int pmcnt3_ppc_a; }; +struct exynos5420_dmc { +unsigned int concontrol; +unsigned int memcontrol; +unsigned int cgcontrol; +unsigned char res500[0x4 ]; +unsigned int directcmd; +unsigned int prechconfig0; +unsigned int phycontrol0; +unsigned int prechconfig1; +unsigned char res1[0x8 ]; +unsigned int pwrdnconfig; +unsigned int timingpzq; +unsigned int timingref; +unsigned int timingrow0; +unsigned int timingdata0; +unsigned int timingpower0; +unsigned int phystatus; +unsigned int etctiming; +unsigned int chipstatus; +unsigned char res3[0x8 ]; +unsigned int mrstatus; +unsigned char res4[0x8 ]; +unsigned int qoscontrol0; +unsigned char resr5[0x4 ]; +unsigned int qoscontrol1; +unsigned char res6[0x4 ]; +unsigned int qoscontrol2; +unsigned char res7[0x4 ]; +unsigned int qoscontrol3; +unsigned char res8[0x4 ]; +unsigned int qoscontrol4; +unsigned char res9[0x4 ]; +unsigned int qoscontrol5; +unsigned char res10[0x4 ]; +unsigned int qoscontrol6; +unsigned char res11[0x4 ]; +unsigned int qoscontrol7; +unsigned char res12[0x4 ]; +unsigned int qoscontrol8; +unsigned char res13[0x4 ]; +unsigned int qoscontrol9; +unsigned char res14[0x4 ]; +unsigned int qoscontrol10; +unsigned char res15[0x4 ]; +unsigned int qoscontrol11; +unsigned char res16[0x4 ]; +unsigned int qoscontrol12; +unsigned char res17[0x4 ]; +unsigned int qoscontrol13; +unsigned char res18[0x4 ]; +unsigned int qoscontrol14; +unsigned char res19[0x4 ]; +unsigned int qoscontrol15; +unsigned char res20[0x4 ]; +unsigned int timing_set_sw; +unsigned int timingrow1; +unsigned int timingdata1; +unsigned int timingpower1; +unsigned char res300[0x4 ]; +unsigned int wrtra_config; +unsigned int rdlvl_config; +unsigned char res21[0x4 ]; +unsigned int brbrsvcontrol; +unsigned int brbrsvconfig; +unsigned int brbqosconfig; +unsigned char res301[0x14 ]; +unsigned int wrlvl_config0; +unsigned int wrlvl_config1; +unsigned int wrlvl_status; +unsigned char res23[0x4 ]; +unsigned int ppcclockon; +unsigned int perevconfig0; +unsigned int perevconfig1; +unsigned int perevconfig2; +unsigned int perevconfig3; +unsigned char res24[0xc ]; +unsigned int control_io_rdata; +unsigned char res240[0xc ]; +unsigned int cacal_config0; +unsigned int cacal_config1; +unsigned int cacal_status; +unsigned char res302[0xa4 ]; +unsigned int bp_control0; +unsigned int bp_config0_r; +unsigned int bp_config0_w; +unsigned char res303[0x4 ]; +unsigned int bp_control1; +unsigned int bp_config1_r; +unsigned int bp_config1_w; +unsigned char res304[0x4 ]; +unsigned int bp_control2; +unsigned int bp_config2_r; +unsigned int bp_config2_w; +unsigned char res305[0x4 ]; +unsigned int bp_control3; +unsigned int bp_config3_r; +unsigned int bp_config3_w; +unsigned char res306[0xddb4 ]; +unsigned int pmnc_ppc; +unsigned char res25[0xc ]; +unsigned int cntens_ppc; +unsigned char res26[0xc ]; +unsigned int cntenc_ppc; +unsigned char res27[0xc ]; +unsigned int intens_ppc; +unsigned char res28[0xc ]; +unsigned int intenc_ppc; +unsigned char res29[0xc ]; +unsigned int flag_ppc; +unsigned char res30[0xac ]; +unsigned int ccnt_ppc; +unsigned char res31[0xc ]; +unsigned int pmcnt0_ppc; +unsigned char res32[0xc ]; +unsigned int pmcnt1_ppc; +unsigned char res33[0xc ]; +unsigned int pmcnt2_ppc; +unsigned char res34[0xc ]; +unsigned int pmcnt3_ppc; +}; +struct exynos5_phy_control {unsigned int phy_con0;unsigned int phy_con1;
@@ -252,6 +373,52 @@ struct exynos5_phy_control {unsigned int phy_con42; }; +struct exynos5420_phy_control { +unsigned int phy_con0; +unsigned int phy_con1; +unsigned int phy_con2; +unsigned int phy_con3; +unsigned int phy_con4; +unsigned int phy_con5; +unsigned int phy_con6; +unsigned char res2[0x4 ]; +unsigned int phy_con8; +unsigned char res5[0x4 ]; +unsigned int phy_con10; +unsigned int phy_con11; +unsigned int phy_con12; +unsigned int phy_con13; +unsigned int phy_con14; +unsigned int phy_con15; +unsigned int phy_con16; +unsigned char res4[0x4 ]; +unsigned int phy_con17; +unsigned int phy_con18; +unsigned int phy_con19; +unsigned int phy_con20; +unsigned int phy_con21; +unsigned int phy_con22; +unsigned int phy_con23; +unsigned int phy_con24; +unsigned int phy_con25; +unsigned int phy_con26; +unsigned int phy_con27; +unsigned int phy_con28; +unsigned int phy_con29; +unsigned int phy_con30; +unsigned int phy_con31; +unsigned int phy_con32; +unsigned int phy_con33; +unsigned int phy_con34; +unsigned char res6[0x8 ]; +unsigned int phy_con37; +unsigned char res7[0x4 ]; +unsigned int phy_con39; +unsigned int phy_con40; +unsigned int phy_con41; +unsigned int phy_con42; +}; +enum ddr_mode {DDR_MODE_DDR2 ,DDR_MODE_DDR3 ,
Signature · 1 line
1.7.12.4
PATCH v13 5/11 Exynos5420: Add clock initialization for 5420
In reply to Rajeshwari S ShindeThis patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic for exynos5420_set_spi_clk api.
Changes in V8:
- Chnages the if condition loop for pro_id and cpu_id.
Changes in V9:
- Used samsung_get_base to get base address of clock.
Changes in V10:
- Corrected the comments and few coding style nits.
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/cpu/armv7/exynos/clock.c | 279 +++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ 6 files changed, 1679 insertions(+), 202 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +264 -15
@@ -96,7 +96,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k) freq =CONFIG_SYS_CLK_FREQ ; -if (pllreg ==EPLL ) { +if (pllreg ==EPLL || pllreg ==RPLL ) { k = k &0xffff ;/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */ fout = (m + k /PLL_DIV_65536 ) * (freq / (p * (1 << s)));
@@ -117,7 +117,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k) div =PLL_DIV_1024 ; else if (proid_is_exynos4412()) div =PLL_DIV_65535 ; - else if (proid_is_exynos5250()) + else if (proid_is_exynos5250() || proid_is_exynos5420()) div =PLL_DIV_65536 ; else return 0;
@@ -362,6 +362,43 @@ unsigned long clock_get_periph_rate(int peripheral)return 0 ; } +/* exynos5420: return pll clock frequency */ +static unsigned long exynos5420_get_pll_clk (int pllreg) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long r, k =0 ; + +switch (pllreg) { +case APLL : + r =readl (&clk->apll_con0); +break ; +case MPLL : + r =readl (&clk->mpll_con0); +break ; +case EPLL : + r =readl (&clk->epll_con0); + k =readl (&clk->epll_con1); +break ; +case VPLL : + r =readl (&clk->vpll_con0); + k =readl (&clk->vpll_con1); +break ; +case BPLL : + r =readl (&clk->bpll_con0); +break ; +case RPLL : + r =readl (&clk->rpll_con0); + k =readl (&clk->rpll_con1); +break ; +default : +printf ("Unsupported PLL (%d)\n" , pllreg); +return 0 ; + } + +return exynos_get_pll_clk (pllreg, r, k); +} +/* exynos4: return ARM clock frequency */ static unsigned long exynos4_get_arm_clk (void ) {
@@ -485,6 +522,27 @@ static unsigned long exynos4x12_get_pwm_clk(void)return pclk; } +/* exynos5420: return pwm clock frequency */ +static unsigned long exynos5420_get_pwm_clk (void ) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long pclk, sclk; +unsigned int ratio; + +/* +* CLK_DIV_PERIC0 +* PWM_RATIO [31:28] +*/ + ratio =readl (&clk->div_peric0); + ratio = (ratio >>28 ) &0xf ; + sclk =get_pll_clk (MPLL ); + + pclk = sclk / (ratio +1 ); + +return pclk; +} +/* exynos4: return uart clock frequency */ static unsigned long exynos4_get_uart_clk (int dev_index) {
@@ -624,6 +682,53 @@ static unsigned long exynos5_get_uart_clk(int dev_index)return uclk; } +/* exynos5420: return uart clock frequency */ +static unsigned long exynos5420_get_uart_clk (int dev_index) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long uclk, sclk; +unsigned int sel; +unsigned int ratio; + +/* +* CLK_SRC_PERIC0 +* UART0_SEL [6:4] +* UART1_SEL [10:8] +* UART2_SEL [14:12] +* UART3_SEL [18:16] +* generalised calculation as follows +* sel = (sel >> ((dev_index * 4) + 4)) & mask; +*/ + sel =readl (&clk->src_peric0); + sel = (sel >> ((dev_index *4 ) +4 )) &0x7 ; + +if (sel ==0x3 ) + sclk =get_pll_clk (MPLL ); +else if (sel ==0x6 ) + sclk =get_pll_clk (EPLL ); +else if (sel ==0x7 ) + sclk =get_pll_clk (RPLL ); +else +return 0 ; + +/* +* CLK_DIV_PERIC0 +* UART0_RATIO [11:8] +* UART1_RATIO [15:12] +* UART2_RATIO [19:16] +* UART3_RATIO [23:20] +* generalised calculation as follows +* ratio = (ratio >> ((dev_index * 4) + 8)) & mask; +*/ + ratio =readl (&clk->div_peric0); + ratio = (ratio >> ((dev_index *4 ) +8 )) &0xf ; + + uclk = sclk / (ratio +1 ); + +return uclk; +} +static unsigned long exynos4_get_mmc_clk (int dev_index) { struct exynos4_clock *clk =
@@ -718,6 +823,47 @@ static unsigned long exynos5_get_mmc_clk(int dev_index)return uclk; } +static unsigned long exynos5420_get_mmc_clk (int dev_index) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long uclk, sclk; +unsigned int sel, ratio; + +/* +* CLK_SRC_FSYS +* MMC0_SEL [10:8] +* MMC1_SEL [14:12] +* MMC2_SEL [18:16] +* generalised calculation as follows +* sel = (sel >> ((dev_index * 4) + 8)) & mask +*/ + sel =readl (&clk->src_fsys); + sel = (sel >> ((dev_index *4 ) +8 )) &0x7 ; + +if (sel ==0x3 ) + sclk =get_pll_clk (MPLL ); +else if (sel ==0x6 ) + sclk =get_pll_clk (EPLL ); +else +return 0 ; + +/* +* CLK_DIV_FSYS1 +* MMC0_RATIO [9:0] +* MMC1_RATIO [19:10] +* MMC2_RATIO [29:20] +* generalised calculation as follows +* ratio = (ratio >> (dev_index * 10)) & mask +*/ + ratio =readl (&clk->div_fsys1); + ratio = (ratio >> (dev_index *10 )) &0x3ff ; + + uclk = (sclk / (ratio +1 )); + +return uclk; +} +/* exynos4: set the mmc clock */ static void exynos4_set_mmc_clk (int dev_index,unsigned int div) {
@@ -804,6 +950,29 @@ static void exynos5_set_mmc_clk(int dev_index, unsigned int div)writel (val, addr); } +/* exynos5: set the mmc clock */ +static void exynos5420_set_mmc_clk (int dev_index,unsigned int div) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned int addr; +unsigned int val, shift; + +/* +* CLK_DIV_FSYS1 +* MMC0_RATIO [9:0] +* MMC1_RATIO [19:10] +* MMC2_RATIO [29:20] +*/ + addr = (unsigned int )&clk->div_fsys1; + shift = dev_index *10 ; + + val =readl (addr); + val &= ~(0x3ff << shift); + val |= (div &0x3ff ) << shift; +writel (val, addr); +} +/* get_lcd_clk: return lcd clock frequency */ static unsigned long exynos4_get_lcd_clk (void ) {
@@ -1324,6 +1493,71 @@ static int exynos5_set_spi_clk(enum periph_id periph_id,return 0 ; } +static int exynos5420_set_spi_clk (enum periph_id periph_id, +unsigned int rate) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +int main; +unsigned int fine; +unsigned shift, pre_shift; +unsigned div_mask =0xf , pre_div_mask =0xff ; +u32 *reg; +u32 *pre_reg; + + main =clock_calc_best_scalar (4 ,8 ,400000000 , rate, &fine); +if (main <0 ) { +debug ("%s: Cannot set clock rate for periph %d" , + __func__, periph_id); +return -1 ; + } + main = main -1 ; + fine = fine -1 ; + +switch (periph_id) { +case PERIPH_ID_SPI0 : + reg = &clk->div_peric1; + shift =20 ; + pre_reg = &clk->div_peric4; + pre_shift =8 ; +break ; +case PERIPH_ID_SPI1 : + reg = &clk->div_peric1; + shift =24 ; + pre_reg = &clk->div_peric4; + pre_shift =16 ; +break ; +case PERIPH_ID_SPI2 : + reg = &clk->div_peric1; + shift =28 ; + pre_reg = &clk->div_peric4; + pre_shift =24 ; +break ; +case PERIPH_ID_SPI3 : + reg = &clk->div_isp1; + shift =16 ; + pre_reg = &clk->div_isp1; + pre_shift =0 ; +break ; +case PERIPH_ID_SPI4 : + reg = &clk->div_isp1; + shift =20 ; + pre_reg = &clk->div_isp1; + pre_shift =8 ; +break ; +default : +debug ("%s: Unsupported peripheral ID %d\n" , __func__, + periph_id); +return -1 ; + } + +clrsetbits_le32 (reg, div_mask << shift, (main & div_mask) << shift); +clrsetbits_le32 (pre_reg, pre_div_mask << pre_shift, + (fine & pre_div_mask) << pre_shift); + +return 0 ; +} +static unsigned long exynos4_get_i2c_clk (void ) { struct exynos4_clock *clk =
@@ -1341,9 +1575,11 @@ static unsigned long exynos4_get_i2c_clk(void)unsigned long get_pll_clk (int pllreg) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_pll_clk (pllreg);return exynos5_get_pll_clk (pllreg); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_pll_clk (pllreg);return exynos4_get_pll_clk (pllreg);
@@ -1375,9 +1611,11 @@ unsigned long get_i2c_clk(void)unsigned long get_pwm_clk (void ) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_pwm_clk ();return clock_get_periph_rate (PERIPH_ID_PWM0 ); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_pwm_clk ();return exynos4_get_pwm_clk ();
@@ -1386,9 +1624,11 @@ unsigned long get_pwm_clk(void)unsigned long get_uart_clk (int dev_index) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_uart_clk (dev_index);return exynos5_get_uart_clk (dev_index); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_uart_clk (dev_index);return exynos4_get_uart_clk (dev_index);
@@ -1397,17 +1637,23 @@ unsigned long get_uart_clk(int dev_index)unsigned long get_mmc_clk (int dev_index) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_mmc_clk (dev_index);return exynos5_get_mmc_clk (dev_index); -else + }else {return exynos4_get_mmc_clk (dev_index); + } }void set_mmc_clk (int dev_index,unsigned int div) { -if (cpu_is_exynos5 ()) -exynos5_set_mmc_clk (dev_index, div); -else { +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +exynos5420_set_mmc_clk (dev_index, div); +else +exynos5_set_mmc_clk (dev_index, div); + }else {if (proid_is_exynos4412 ())exynos4x12_set_mmc_clk (dev_index, div);else
@@ -1439,10 +1685,13 @@ void set_mipi_clk(void)int set_spi_clk (int periph_id,unsigned int rate) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_set_spi_clk (periph_id, rate);return exynos5_set_spi_clk (periph_id, rate); -else + }else {return 0 ; + } } int set_i2s_clk_prescaler(unsigned int src_frq, unsigned int dst_frq,
arch/arm/cpu/armv7/exynos/clock_init.h +17 -0
@@ -10,7 +10,11 @@#define __EXYNOS_CLOCK_INIT_Henum { +#ifdef CONFIG_EXYNOS5420 +MEM_TIMINGS_MSR_COUNT =5 , +#else MEM_TIMINGS_MSR_COUNT =4 , +#endif };/* These are the ratio's for configuring ARM clock */
@@ -59,6 +63,18 @@ struct mem_timings {unsigned bpll_mdiv;unsigned bpll_pdiv;unsigned bpll_sdiv; +unsigned kpll_mdiv; +unsigned kpll_pdiv; +unsigned kpll_sdiv; +unsigned dpll_mdiv; +unsigned dpll_pdiv; +unsigned dpll_sdiv; +unsigned ipll_mdiv; +unsigned ipll_pdiv; +unsigned ipll_sdiv; +unsigned spll_mdiv; +unsigned spll_pdiv; +unsigned spll_sdiv;unsigned pclk_cdrex_ratio;unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT ];
@@ -115,6 +131,7 @@ struct mem_timings {uint8_t send_zq_init;/* 1 to send this command */ unsigned impedance;/* drive strength impedeance */ uint8_t gate_leveling_enable;/* check gate leveling is enabled */ +uint8_t read_leveling_enable;/* check h/w read leveling is enabled */ };/**
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +338 -14
390 lines not on this page · raw message
arch/arm/cpu/armv7/exynos/exynos5_setup.h +565 -173
854 lines not on this page · raw message
arch/arm/include/asm/arch-exynos/clk.h +1 -0
@@ -14,6 +14,7 @@#define HPLL 3#define VPLL 4#define BPLL 5 +#define RPLL 6enum pll_src_bit {EXYNOS_SRC_MPLL =6 ,
arch/arm/include/asm/arch-exynos/clock.h +494 -0
500 lines not on this page · raw message
Signature · 1 line
1.7.12.4
PATCH v13 6/11 Exynos5420: Add DDR3 initialization for 5420
In reply to Rajeshwari S ShindeThis patch intends to add DDR3 initialization code for Exynos5420.
---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None
Changes in V9:
- Used samsung_get base to get the dmc base address
Changes in V10:
- Changed to new 5420 dmc and power resgister structure.
- Changed the input parameters for dmc common functions due to changes in the dmc register structure.
Changes in V11:
- None
Changes in V12:
- Changed const void* to uint32_t *
Changes in V13:
- None
arch/arm/cpu/armv7/exynos/dmc_common.c | 60 ++-- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 +++++++++++++++++++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 26 +- arch/arm/include/asm/arch-exynos/cpu.h | 7 +- arch/arm/include/asm/arch-exynos/dmc.h | 10 + 5 files changed, 484 insertions(+), 58 deletions(-)
arch/arm/cpu/armv7/exynos/dmc_common.c +26 -34
@@ -1,5 +1,5 @@/* -* Mem setup common file for different types of DDR present on SMDK5250 boards. +* Mem setup common file for different types of DDR present on Exynos boards. * * Copyright (C) 2012 Samsung Electronics *
@@ -15,9 +15,9 @@#define ZQ_INIT_TIMEOUT 10000 -int dmc_config_zq (struct mem_timings *mem, -struct exynos5_phy_control *phy0_ctrl, -struct exynos5_phy_control *phy1_ctrl) +int dmc_config_zq (struct mem_timings *mem,uint32_t *phy0_con16, +uint32_t *phy1_con16,uint32_t *phy0_con17, +uint32_t *phy1_con17) {unsigned long val =0 ;int i;
@@ -31,19 +31,19 @@ int dmc_config_zq(struct mem_timings *mem, val |= mem->zq_mode_dds <<PHY_CON16_ZQ_MODE_DDS_SHIFT ; val |= mem->zq_mode_term <<PHY_CON16_ZQ_MODE_TERM_SHIFT ; val |=ZQ_CLK_DIV_EN ; -writel (val, &phy0_ctrl->phy_con16); -writel (val, &phy1_ctrl->phy_con16); +writel (val, phy0_con16); +writel (val, phy1_con16);/* Disable termination */ if (mem->zq_mode_noterm) val |=PHY_CON16_ZQ_MODE_NOTERM_MASK ; -writel (val, &phy0_ctrl->phy_con16); -writel (val, &phy1_ctrl->phy_con16); +writel (val, phy0_con16); +writel (val, phy1_con16);/* ZQ_MANUAL_START: Enable */ val |=ZQ_MANUAL_STR ; -writel (val, &phy0_ctrl->phy_con16); -writel (val, &phy1_ctrl->phy_con16); +writel (val, phy0_con16); +writel (val, phy1_con16);/* ZQ_MANUAL_START: Disable */ val &= ~ZQ_MANUAL_STR ;
@@ -53,47 +53,47 @@ int dmc_config_zq(struct mem_timings *mem,* we are looping for the ZQ_init to complete. */ i =ZQ_INIT_TIMEOUT ; -while ((readl (&phy0_ctrl->phy_con17) &ZQ_DONE ) !=ZQ_DONE && i >0 ) { +while ((readl (phy0_con17) &ZQ_DONE ) !=ZQ_DONE && i >0 ) {sdelay (100 ); i--; }if (!i)return -1 ; -writel (val, &phy0_ctrl->phy_con16); +writel (val, phy0_con16); i =ZQ_INIT_TIMEOUT ; -while ((readl (&phy1_ctrl->phy_con17) &ZQ_DONE ) !=ZQ_DONE && i >0 ) { +while ((readl (phy1_con17) &ZQ_DONE ) !=ZQ_DONE && i >0 ) {sdelay (100 ); i--; }if (!i)return -1 ; -writel (val, &phy1_ctrl->phy_con16); +writel (val, phy1_con16);return 0 ; } -void update_reset_dll (struct exynos5_dmc *dmc,enum ddr_mode mode) +void update_reset_dll (uint32_t *phycontrol0,enum ddr_mode mode) {unsigned long val;if (mode ==DDR_MODE_DDR3 ) { val =MEM_TERM_EN |PHY_TERM_EN |DMC_CTRL_SHGATE ; -writel (val, &dmc->phycontrol0); +writel (val, phycontrol0); }/* Update DLL Information: Force DLL Resyncronization */ - val =readl (&dmc->phycontrol0); + val =readl (phycontrol0); val |=FP_RSYNC ; -writel (val, &dmc->phycontrol0); +writel (val, phycontrol0);/* Reset Force DLL Resyncronization */ - val =readl (&dmc->phycontrol0); + val =readl (phycontrol0); val &= ~FP_RSYNC ; -writel (val, &dmc->phycontrol0); +writel (val, phycontrol0); } -void dmc_config_mrs (struct mem_timings *mem,struct exynos5_dmc *dmc) +void dmc_config_mrs (struct mem_timings *mem,uint32_t *directcmd) {int channel, chip;
@@ -107,7 +107,7 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc) mask |= chip <<DIRECT_CMD_CHIP_SHIFT ;/* Sending NOP command */ -writel (DIRECT_CMD_NOP | mask, &dmc->directcmd); +writel (DIRECT_CMD_NOP | mask, directcmd);/* * TODO(alim.akhtar at samsung.com): Do we need these
@@ -119,14 +119,14 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)/* Sending EMRS/MRS commands */ for (i =0 ; i <MEM_TIMINGS_MSR_COUNT ; i++) {writel (mem->direct_cmd_msr[i] | mask, - &dmc->directcmd); + directcmd);sdelay (0x10000 ); }if (mem->send_zq_init) {/* Sending ZQINIT command */ writel (DIRECT_CMD_ZQINIT | mask, - &dmc->directcmd); + directcmd);sdelay (10000 ); }
@@ -134,7 +134,7 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc) } } -void dmc_config_prech (struct mem_timings *mem,struct exynos5_dmc *dmc) +void dmc_config_prech (struct mem_timings *mem,uint32_t *directcmd) {int channel, chip;
@@ -146,20 +146,12 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc) mask |= chip <<DIRECT_CMD_CHIP_SHIFT ;/* PALL (all banks precharge) CMD */ -writel (DIRECT_CMD_PALL | mask, &dmc->directcmd); +writel (DIRECT_CMD_PALL | mask, directcmd);sdelay (0x10000 ); } } } -void dmc_config_memory (struct mem_timings *mem,struct exynos5_dmc *dmc) -{ -writel (mem->memconfig, &dmc->memconfig0); -writel (mem->memconfig, &dmc->memconfig1); -writel (DMC_MEMBASECONFIG0_VAL , &dmc->membaseconfig0); -writel (DMC_MEMBASECONFIG1_VAL , &dmc->membaseconfig1); -} -void mem_ctrl_init (int reset) {struct spl_machine_param *param =spl_get_machine_params ();
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +429 -10
498 lines not on this page · raw message
arch/arm/cpu/armv7/exynos/exynos5_setup.h +14 -12
@@ -696,6 +696,7 @@#define CLK_DIV_CPERI1_VAL NOT_AVAILABLE#else +#define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000/* APLL_CON1 */ #define APLL_CON1_VAL (0x0020F300)
@@ -907,37 +908,38 @@ void lpddr3_mem_ctrl_init(void);* Configure ZQ I/O interface * * @param mem Memory timings for this memory type. -* @param phy0_ctrl Pointer to struct containing PHY0 control reg -* @param phy1_ctrl Pointer to struct containing PHY1 control reg +* @param phy0_con16 Register address for dmc_phy0->phy_con16 +* @param phy1_con16 Register address for dmc_phy1->phy_con16 +* @param phy0_con17 Register address for dmc_phy0->phy_con17 +* @param phy1_con17 Register address for dmc_phy1->phy_con17 * @return 0 if ok, -1 on error */ -int dmc_config_zq (struct mem_timings *mem, -struct exynos5_phy_control *phy0_ctrl, -struct exynos5_phy_control *phy1_ctrl); - +int dmc_config_zq (struct mem_timings *mem,uint32_t *phy0_con16, +uint32_t *phy1_con16,uint32_t *phy0_con17, +uint32_t *phy1_con17);/* * Send NOP and MRS/EMRS Direct commands * * @param mem Memory timings for this memory type. -* @param dmc Pointer to struct of DMC registers +* @param directcmd Register address for dmc_phy->directcmd */ -void dmc_config_mrs (struct mem_timings *mem,struct exynos5_dmc *dmc); +void dmc_config_mrs (struct mem_timings *mem,uint32_t *directcmd);/* * Send PALL Direct commands * * @param mem Memory timings for this memory type. -* @param dmc Pointer to struct of DMC registers +* @param directcmd Register address for dmc_phy->directcmd */ -void dmc_config_prech (struct mem_timings *mem,struct exynos5_dmc *dmc); +void dmc_config_prech (struct mem_timings *mem,uint32_t *directcmd);/* * Reset the DLL. This function is common between DDR3 and LPDDR2. * However, the reset value is different. So we are passing a flag * ddr_mode to distinguish between LPDDR2 and DDR3. * -* @param exynos5_dmc Pointer to struct of DMC registers +* @param phycontrol0 Register address for dmc_phy->phycontrol0 * @param ddr_mode Type of DDR memory */ -void update_reset_dll (struct exynos5_dmc *,enum ddr_mode ); +void update_reset_dll (uint32_t *phycontrol0,enum ddr_mode );#endif
arch/arm/include/asm/arch-exynos/cpu.h +5 -2
@@ -53,6 +53,7 @@#define EXYNOS4_AUDIOSS_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4_USB_HOST_XHCI_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4_USB3PHY_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS4_DMC_TZASC_BASE DEVICE_NOT_AVAILABLE/* EXYNOS4X12 */ #define EXYNOS4X12_GPIO_PART3_BASE 0x03860000
@@ -91,6 +92,7 @@#define EXYNOS4X12_AUDIOSS_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4X12_USB_HOST_XHCI_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4X12_USB3PHY_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS4X12_DMC_TZASC_BASE DEVICE_NOT_AVAILABLE/* EXYNOS5 */ #define EXYNOS5_I2C_SPACING 0x10000
@@ -129,6 +131,7 @@#define EXYNOS5_ADC_BASE DEVICE_NOT_AVAILABLE#define EXYNOS5_MODEM_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5_DMC_TZASC_BASE DEVICE_NOT_AVAILABLE/* EXYNOS5420 */ #define EXYNOS5420_AUDIOSS_BASE 0x03810000
@@ -143,8 +146,7 @@#define EXYNOS5420_ACE_SFR_BASE 0x10830000#define EXYNOS5420_DMC_PHY_BASE 0x10C00000#define EXYNOS5420_DMC_CTRL_BASE 0x10C20000 -#define EXYNOS5420_DMC_TZASC0_BASE 0x10D40000 -#define EXYNOS5420_DMC_TZASC1_BASE 0x10D50000 +#define EXYNOS5420_DMC_TZASC_BASE 0x10D40000#define EXYNOS5420_USB_HOST_EHCI_BASE 0x12110000#define EXYNOS5420_MMC_BASE 0x12200000#define EXYNOS5420_SROMC_BASE 0x12250000
@@ -284,6 +286,7 @@ SAMSUNG_BASE(spi_isp, SPI_ISP_BASE) SAMSUNG_BASE(tzpc, TZPC_BASE) SAMSUNG_BASE(dmc_ctrl, DMC_CTRL_BASE) SAMSUNG_BASE(dmc_phy, DMC_PHY_BASE) +SAMSUNG_BASE(dmc_tzasc, DMC_TZASC_BASE) SAMSUNG_BASE(audio_ass, AUDIOSS_BASE)#endif
arch/arm/include/asm/arch-exynos/dmc.h +10 -0
@@ -419,6 +419,15 @@ struct exynos5420_phy_control {unsigned int phy_con42; }; +struct exynos5420_tzasc { +unsigned char res1[0xf00 ]; +unsigned int membaseconfig0; +unsigned int membaseconfig1; +unsigned char res2[0x8 ]; +unsigned int memconfig0; +unsigned int memconfig1; +}; +enum ddr_mode {DDR_MODE_DDR2 ,DDR_MODE_DDR3 ,
@@ -453,6 +462,7 @@ enum mem_manuf {#define PHY_CON0_T_WRRDCMD_SHIFT 17#define PHY_CON0_T_WRRDCMD_MASK (0x7 << PHY_CON0_T_WRRDCMD_SHIFT)#define PHY_CON0_CTRL_DDR_MODE_SHIFT 11 +#define PHY_CON0_CTRL_DDR_MODE_MASK 0x3/* PHY_CON1 register fields */ #define PHY_CON1_RDLVL_RDDATA_ADJ_SHIFT 0
Signature · 1 line
1.7.12.4
PATCH v13 7/11 Exynos5420: Add support for 5420 in pinmux and gpio
In reply to Rajeshwari S ShindeAdds code in pinmux and gpio framework to support Exynos5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added correct calculation of gpio based addresses.
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the coding style nits.
Chnages in V8:
- Corrected the coding style nits pointed by Minkyu Kang.
Changes in V9:
- None
Changes in V10:
- None
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/cpu/armv7/exynos/pinmux.c | 260 +++++++++++++++++++++++++++++- arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++++++++++++-- arch/arm/include/asm/arch-exynos/periph.h | 3 + 3 files changed, 390 insertions(+), 16 deletions(-)
arch/arm/cpu/armv7/exynos/pinmux.c +258 -2
@@ -46,6 +46,42 @@ static void exynos5_uart_config(int peripheral) } } +static void exynos5420_uart_config (int peripheral) +{ +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); +struct s5p_gpio_bank *bank; +int i, start, count; + +switch (peripheral) { +case PERIPH_ID_UART0 : + bank = &gpio1->a0; + start =0 ; + count =4 ; +break ; +case PERIPH_ID_UART1 : + bank = &gpio1->a0; + start =4 ; + count =4 ; +break ; +case PERIPH_ID_UART2 : + bank = &gpio1->a1; + start =0 ; + count =4 ; +break ; +case PERIPH_ID_UART3 : + bank = &gpio1->a1; + start =4 ; + count =2 ; +break ; + } + +for (i = start; i < start + count; i++) { +s5p_gpio_set_pull (bank, i,GPIO_PULL_NONE ); +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); + } +} +static int exynos5_mmc_config (int peripheral,int flags) { struct exynos5_gpio_part1 *gpio1 =
@@ -101,6 +137,75 @@ static int exynos5_mmc_config(int peripheral, int flags)return 0 ; } +static int exynos5420_mmc_config (int peripheral,int flags) +{ +struct exynos5420_gpio_part3 *gpio3 = + (struct exynos5420_gpio_part3 *)samsung_get_base_gpio_part3 (); +struct s5p_gpio_bank *bank =NULL , *bank_ext =NULL ; +int i, start; + +switch (peripheral) { +case PERIPH_ID_SDMMC0 : + bank = &gpio3->c0; + bank_ext = &gpio3->c3; + start =0 ; +break ; +case PERIPH_ID_SDMMC1 : + bank = &gpio3->c1; + bank_ext = &gpio3->d1; + start =4 ; +break ; +case PERIPH_ID_SDMMC2 : + bank = &gpio3->c2; + bank_ext =NULL ; + start =0 ; +break ; +default : + start =0 ; +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return -1 ; + } + +if ((flags &PINMUX_FLAG_8BIT_MODE ) && !bank_ext) { +debug ("SDMMC device %d does not support 8bit mode" , + peripheral); +return -1 ; + } + +if (flags &PINMUX_FLAG_8BIT_MODE ) { +for (i = start; i <= (start +3 ); i++) { +s5p_gpio_cfg_pin (bank_ext, i,GPIO_FUNC (0x2 )); +s5p_gpio_set_pull (bank_ext, i,GPIO_PULL_UP ); +s5p_gpio_set_drv (bank_ext, i,GPIO_DRV_4X ); + } + } + +for (i =0 ; i <3 ; i++) { +/* +* MMC0 is intended to be used for eMMC. The +* card detect pin is used as a VDDEN signal to +* power on the eMMC. The 5420 iROM makes +* this same assumption. +*/ +if ((peripheral ==PERIPH_ID_SDMMC0 ) && (i ==2 )) { +s5p_gpio_set_value (bank, i,1 ); +s5p_gpio_cfg_pin (bank, i,GPIO_OUTPUT ); + }else { +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); + } +s5p_gpio_set_pull (bank, i,GPIO_PULL_NONE ); +s5p_gpio_set_drv (bank, i,GPIO_DRV_4X ); + } + +for (i =3 ; i <=6 ; i++) { +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); +s5p_gpio_set_pull (bank, i,GPIO_PULL_UP ); +s5p_gpio_set_drv (bank, i,GPIO_DRV_4X ); + } + +return 0 ; +} +static void exynos5_sromc_config (int flags) { struct exynos5_gpio_part1 *gpio1 =
@@ -216,6 +321,59 @@ static void exynos5_i2c_config(int peripheral, int flags) } } +static void exynos5420_i2c_config (int peripheral) +{ +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); + +switch (peripheral) { +case PERIPH_ID_I2C0 : +s5p_gpio_cfg_pin (&gpio1->b3,0 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,1 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C1 : +s5p_gpio_cfg_pin (&gpio1->b3,2 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,3 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C2 : +s5p_gpio_cfg_pin (&gpio1->a0,6 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a0,7 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C3 : +s5p_gpio_cfg_pin (&gpio1->a1,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a1,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C4 : +s5p_gpio_cfg_pin (&gpio1->a2,0 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a2,1 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C5 : +s5p_gpio_cfg_pin (&gpio1->a2,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a2,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C6 : +s5p_gpio_cfg_pin (&gpio1->b1,3 ,GPIO_FUNC (0x4 )); +s5p_gpio_cfg_pin (&gpio1->b1,4 ,GPIO_FUNC (0x4 )); +break ; +case PERIPH_ID_I2C7 : +s5p_gpio_cfg_pin (&gpio1->b2,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->b2,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C8 : +s5p_gpio_cfg_pin (&gpio1->b3,4 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,5 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C9 : +s5p_gpio_cfg_pin (&gpio1->b3,6 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,7 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C10 : +s5p_gpio_cfg_pin (&gpio1->b4,0 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b4,1 ,GPIO_FUNC (0x2 )); +break ; + } +} +static void exynos5_i2s_config (int peripheral) {int i;
@@ -279,6 +437,58 @@ void exynos5_spi_config(int peripheral) } } +void exynos5420_spi_config (int peripheral) +{ +int cfg, pin, i; +struct s5p_gpio_bank *bank =NULL ; +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); +struct exynos5420_gpio_part4 *gpio4 = + (struct exynos5420_gpio_part4 *)samsung_get_base_gpio_part4 (); + +switch (peripheral) { +case PERIPH_ID_SPI0 : + bank = &gpio1->a2; + cfg =GPIO_FUNC (0x2 ); + pin =0 ; +break ; +case PERIPH_ID_SPI1 : + bank = &gpio1->a2; + cfg =GPIO_FUNC (0x2 ); + pin =4 ; +break ; +case PERIPH_ID_SPI2 : + bank = &gpio1->b1; + cfg =GPIO_FUNC (0x5 ); + pin =1 ; +break ; +case PERIPH_ID_SPI3 : + bank = &gpio4->f1; + cfg =GPIO_FUNC (0x2 ); + pin =0 ; +break ; +case PERIPH_ID_SPI4 : + cfg =0 ; + pin =0 ; +break ; +default : + cfg =0 ; + pin =0 ; +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return ; + } + +if (peripheral !=PERIPH_ID_SPI4 ) { +for (i = pin; i < pin +4 ; i++) +s5p_gpio_cfg_pin (bank, i, cfg); + }else { +for (i =0 ; i <2 ; i++) { +s5p_gpio_cfg_pin (&gpio4->f0, i +2 ,GPIO_FUNC (0x4 )); +s5p_gpio_cfg_pin (&gpio4->e0, i +4 ,GPIO_FUNC (0x4 )); + } + } +} +static int exynos5_pinmux_config (int peripheral,int flags) {switch (peripheral) {
@@ -325,6 +535,48 @@ static int exynos5_pinmux_config(int peripheral, int flags)return 0 ; } +static int exynos5420_pinmux_config (int peripheral,int flags) +{ +switch (peripheral) { +case PERIPH_ID_UART0 : +case PERIPH_ID_UART1 : +case PERIPH_ID_UART2 : +case PERIPH_ID_UART3 : +exynos5420_uart_config (peripheral); +break ; +case PERIPH_ID_SDMMC0 : +case PERIPH_ID_SDMMC1 : +case PERIPH_ID_SDMMC2 : +case PERIPH_ID_SDMMC3 : +return exynos5420_mmc_config (peripheral, flags); +case PERIPH_ID_SPI0 : +case PERIPH_ID_SPI1 : +case PERIPH_ID_SPI2 : +case PERIPH_ID_SPI3 : +case PERIPH_ID_SPI4 : +exynos5420_spi_config (peripheral); +break ; +case PERIPH_ID_I2C0 : +case PERIPH_ID_I2C1 : +case PERIPH_ID_I2C2 : +case PERIPH_ID_I2C3 : +case PERIPH_ID_I2C4 : +case PERIPH_ID_I2C5 : +case PERIPH_ID_I2C6 : +case PERIPH_ID_I2C7 : +case PERIPH_ID_I2C8 : +case PERIPH_ID_I2C9 : +case PERIPH_ID_I2C10 : +exynos5420_i2c_config (peripheral); +break ; +default : +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return -1 ; + } + +return 0 ; +} +static void exynos4_i2c_config (int peripheral,int flags) { struct exynos4_gpio_part1 *gpio1 =
@@ -475,13 +727,17 @@ static int exynos4_pinmux_config(int peripheral, int flags)int exynos_pinmux_config (int peripheral,int flags) {if (cpu_is_exynos5 ()) { -return exynos5_pinmux_config (peripheral, flags); +if (proid_is_exynos5420 ()) +return exynos5420_pinmux_config (peripheral, flags); +else if (proid_is_exynos5250 ()) +return exynos5_pinmux_config (peripheral, flags); }else if (cpu_is_exynos4 ()) {return exynos4_pinmux_config (peripheral, flags); }else {debug ("pinmux functionality not supported\n" ); -return -1 ; } + +return -1 ; }#ifdef CONFIG_OF_CONTROL
arch/arm/include/asm/arch-exynos/gpio.h +129 -14
164 lines not on this page · raw message
arch/arm/include/asm/arch-exynos/periph.h +3 -0
@@ -34,6 +34,9 @@ enum periph_id {PERIPH_ID_SDMMC1 ,PERIPH_ID_SDMMC2 ,PERIPH_ID_SDMMC3 , +PERIPH_ID_I2C8 =87 , +PERIPH_ID_I2C9 , +PERIPH_ID_I2C10 =203 ,PERIPH_ID_I2S0 =98 , PERIPH_ID_I2S1 = 99,
Signature · 1 line
1.7.12.4
PATCH v13 8/11 Exynos5420: Add base patch for SMDK5420
In reply to Rajeshwari S ShindeAdding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functions board_eth_init and board_mmc_init as they were moved to common/board.c
Changes in V6:
- None
Changes in V7:
- added CONFIG_EXYNOS_SPL to build 5420 and 5250
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
board/samsung/common/board.c | 2 + board/samsung/smdk5420/Makefile | 11 +++ board/samsung/smdk5420/smdk5420.c | 159 ++++++++++++++++++++++++++++++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 +++++++++++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5250-dt.h | 1 + tools/Makefile | 3 +- 8 files changed, 229 insertions(+), 1 deletion(-) create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
board/samsung/common/board.c +2 -0
@@ -146,6 +146,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)return local.cros_ec_dev; } +#ifdef CONFIG_CROS_EC static int board_init_cros_ec_devices (const void *blob) { local.cros_ec_err =cros_ec_init (blob, &local.cros_ec_dev);
@@ -154,6 +155,7 @@ static int board_init_cros_ec_devices(const void *blob) return 0; } +#endif #if defined(CONFIG_POWER )#ifdef CONFIG_POWER_MAX77686
board/samsung/smdk5420/Makefile new file +11 -0
@@ -0,0 +1,11 @@ +# +# Copyright (C) 2013 Samsung Electronics +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += smdk5420_spl.o + +ifndef CONFIG_SPL_BUILD +obj-y += smdk5420.o +endif
board/samsung/smdk5420/smdk5420.c new file +159 -0
159 lines not on this page · raw message
board/samsung/smdk5420/smdk5420_spl.c new file +52 -0
52 lines not on this page · raw message
boards.cfg +1 -0
@@ -276,6 +276,7 @@ Active arm armv7 exynos samsung arndale Active arm armv7 exynos samsung origen origen - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 smdk5250 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 snow - Rajeshwari Shinde <[email protected]> +Active arm armv7 exynos samsung smdk5420 smdk5420 - Rajeshwari Shinde <[email protected]> Active arm armv7 exynos samsung smdkv310 smdkv310 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung trats trats - Lukasz Majewski <[email protected]> Active arm armv7 exynos samsung trats2 trats2 - Piotr Wilczek <[email protected]>
include/configs/arndale.h +1 -0
@@ -117,6 +117,7 @@#define CONFIG_USB_STORAGE /* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030
include/configs/exynos5250-dt.h +1 -0
@@ -155,6 +155,7 @@#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20/* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030
tools/Makefile +2 -1
@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX) BIN_FILES-y += mkenvimage$(SFX) BIN_FILES-y += mkimage$(SFX) BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX) +BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX) BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX) BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX) BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o -OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o +OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
Signature · 1 line
1.7.12.4
PATCH v13 9/11 DTS: Add dts support for SMDK5420
In reply to Rajeshwari S ShindeThis patch adds dts support for SMDK5420.exynos5.dtsi created is a common file which has the nodes common to both 5420 and 5250.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added /include/ "exynos5420.dtsi
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the license.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- None
arch/arm/dts/exynos5.dtsi | 198 ++++++++++++++++++++++++++++++ arch/arm/dts/exynos5250.dtsi | 194 +---------------------------- arch/arm/dts/exynos5420.dtsi | 70 +++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++++++++++++++++++++++ 4 files changed, 441 insertions(+), 190 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
arch/arm/dts/exynos5.dtsi new file +198 -0
@@ -0,0 +1,198 @@ +/* + * Copyright (c) 2013 The Chromium OS Authors + * SAMSUNG EXYNOS5 SoC device tree source + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "samsung,exynos5"; + + sromc at 12250000 { + compatible = "samsung,exynos-sromc"; + reg = <0x12250000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c at 12c60000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C60000 0x100>; + interrupts = <0 56 0>; + }; + + i2c at 12c70000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C70000 0x100>; + interrupts = <0 57 0>; + }; + + i2c at 12c80000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C80000 0x100>; + interrupts = <0 58 0>; + }; + + i2c at 12c90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C90000 0x100>; + interrupts = <0 59 0>; + }; + + spi at 12d20000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d20000 0x30>; + interrupts = <0 68 0>; + }; + + spi at 12d30000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d30000 0x30>; + interrupts = <0 69 0>; + }; + + spi at 12d40000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d40000 0x30>; + clock-frequency = <50000000>; + interrupts = <0 70 0>; + }; + + spi at 131a0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x131a0000 0x30>; + interrupts = <0 129 0>; + }; + + spi at 131b0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x131b0000 0x30>; + interrupts = <0 130 0>; + }; + + ehci at 12110000 { + compatible = "samsung,exynos-ehci"; + reg = <0x12110000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + + phy { + compatible = "samsung,exynos-usb-phy"; + reg = <0x12130000 0x100>; + }; + }; + + tmu at 10060000 { + compatible = "samsung,exynos-tmu"; + reg = <0x10060000 0x10000>; + }; + + fimd at 14400000 { + compatible = "samsung,exynos-fimd"; + reg = <0x14400000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + dp at 145b0000 { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + xhci0: xhci at 12000000 { + compatible = "samsung,exynos5250-xhci"; + reg = <0x12000000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + + phy { + compatible = "samsung,exynos5250-usb3-phy"; + reg = <0x12100000 0x100>; + }; + }; + + mmc at 12200000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + }; + + mmc at 12210000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12210000 0x1000>; + interrupts = <0 76 0>; + }; + + mmc at 12220000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12220000 0x1000>; + interrupts = <0 77 0>; + }; + + mmc at 12230000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12230000 0x1000>; + interrupts = <0 78 0>; + }; + + serial at 12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + id = <0>; + }; + + serial at 12C10000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C10000 0x100>; + interrupts = <0 52 0>; + id = <1>; + }; + + serial at 12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C20000 0x100>; + interrupts = <0 53 0>; + id = <2>; + }; + + serial at 12C30000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C30000 0x100>; + interrupts = <0 54 0>; + id = <3>; + }; + + gpio: gpio { + }; +};
arch/arm/dts/exynos5250.dtsi +4 -190
213 lines not on this page · raw message
arch/arm/dts/exynos5420.dtsi new file +70 -0
70 lines not on this page · raw message
board/samsung/dts/exynos5420-smdk5420.dts new file +169 -0
169 lines not on this page · raw message
Signature · 1 line
1.7.12.4
PATCH v13 10/11 Config: Add initial config for SMDK5420
In reply to Rajeshwari S ShindeAdding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- Rebased on latest code.
Changes in V11:
- None
Changes in V12:
- None
Changes in V13:
- Rebased on latest code.
include/configs/exynos5-dt.h | 290 ++++++++++++++++++++++++++++++++++++++++ include/configs/exynos5250-dt.h | 287 +-------------------------------------- include/configs/smdk5420.h | 50 +++++++ 3 files changed, 347 insertions(+), 280 deletions(-) create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
include/configs/exynos5-dt.h new file +290 -0
@@ -0,0 +1,290 @@ +/* +* Copyright (C) 2013 Samsung Electronics +* +* Configuration settings for the SAMSUNG EXYNOS5 board. +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_SAMSUNG /* in a SAMSUNG core */ +#define CONFIG_S5P /* S5P Family */ +#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */ + +#include <asm/arch/cpu.h> /* get chip and board defs */ + +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_COMMON +#define CONFIG_ARCH_EARLY_INIT_R +#define CONFIG_EXYNOS_SPL + +/* Enable fdt support for Exynos5250 */ +#define CONFIG_OF_CONTROL +#define CONFIG_OF_SEPARATE + +/* Allow tracing to be enabled */ +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x50000000 + +/* Keep L2 Cache Disabled */ +#define CONFIG_SYS_DCACHE_OFF +#define CONFIG_SYS_CACHELINE_SIZE 64 + +/* Enable ACE acceleration for SHA1 and SHA256 */ +#define CONFIG_EXYNOS_ACE_SHA +#define CONFIG_SHA_HW_ACCEL + +/* input clock of PLL: SMDK5250 has 24MHz input clock */ +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +/* Power Down Modes */ +#define S5P_CHECK_SLEEP 0x00000BAD +#define S5P_CHECK_DIDLE 0xBAD00000 +#define S5P_CHECK_LPA 0xABAD0000 + +/* Offset for inform registers */ +#define INFORM0_OFFSET 0x800 +#define INFORM1_OFFSET 0x804 +#define INFORM2_OFFSET 0x808 +#define INFORM3_OFFSET 0x80c + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20)) + +/* select serial console configuration */ +#define CONFIG_BAUDRATE 115200 +#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 +#define CONFIG_SILENT_CONSOLE + +/* Enable keyboard */ +#define CONFIG_CROS_EC /* CROS_EC protocol */ +#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */ +#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ +#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */ +#define CONFIG_CMD_CROS_EC +#define CONFIG_KEYBOARD + +/* Console configuration */ +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define EXYNOS_DEVICE_SETTINGS \ + "stdin=serial,cros-ec-keyb\0" \ + "stdout=serial,lcd\0" \ + "stderr=serial,lcd\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXYNOS_DEVICE_SETTINGS + +/* SD/MMC configuration */ +#define CONFIG_GENERIC_MMC +#define CONFIG_MMC +#define CONFIG_SDHCI +#define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC +#define CONFIG_SUPPORT_EMMC_BOOT + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* PWM */ +#define CONFIG_PWM + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command definition*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_NET +#define CONFIG_CMD_HASH + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +/* Thermal Management Unit */ +#define CONFIG_EXYNOS_TMU +#define CONFIG_CMD_DTT +#define CONFIG_TMU_CMD_DTT + +/* TPM */ +#define CONFIG_TPM +#define CONFIG_CMD_TPM +#define CONFIG_TPM_TIS_I2C +#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3 +#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20 + +/* MMC SPL */ +#define CONFIG_SPL +#define COPY_BL2_FNPTR_ADDR 0x02020030 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT + +/* specific .lds file */ +#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds" +#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024) + + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE 384/* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) + +#define CONFIG_RD_LVL + +#define CONFIG_NR_DRAM_BANKS 8 +#define SDRAM_BANK_SIZE (256UL << 20UL)/* 256 MB */ +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) +#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS + +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_SECURE_BL1_ONLY + +/* Secure FW size configuration */ +#ifdef CONFIG_SECURE_BL1_ONLY +#define CONFIG_SEC_FW_SIZE (8 << 10)/* 8KB */ +#else +#define CONFIG_SEC_FW_SIZE 0 +#endif + +/* Configuration of BL1, BL2, ENV Blocks on mmc */ +#define CONFIG_RES_BLOCK_SIZE (512) +#define CONFIG_BL1_SIZE (16 << 10)/*16 K reserved for BL1*/ +#define CONFIG_BL2_SIZE (512UL << 10UL)/* 512 KB */ +#define CONFIG_ENV_SIZE (16 << 10)/* 16 KB */ + +#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) +#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) +#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE) + +/* U-boot copy size from boot Media to DRAM.*/ +#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) +#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) + +#define CONFIG_SPI_BOOTING +#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 +#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) + +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS + +/* I2C */ +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000/* 100 Kbps */ +#define CONFIG_SYS_I2C_S3C24X0 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0 +#define CONFIG_I2C_EDID + +/* SPI */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SPI_FLASH +#define CONFIG_ENV_SPI_BASE 0x12D30000 + +#ifdef CONFIG_SPI_FLASH +#define CONFIG_EXYNOS_SPI +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_GIGADEVICE +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define EXYNOS5_SPI_NUM_CONTROLLERS 5 +#define CONFIG_OF_SPI +#endif + +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE +#define CONFIG_ENV_SPI_BUS 1 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 +#endif + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C + +/* Ethernet Controllor Driver */ +#ifdef CONFIG_CMD_NET +#define CONFIG_SMC911X +#define CONFIG_SMC911X_BASE 0x5000000 +#define CONFIG_SMC911X_16_BIT +#define CONFIG_ENV_SROM_BANK 1 +#endif /*CONFIG_CMD_NET*/ + +/* Enable PXE Support */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PXE +#define CONFIG_MENU +#endif + +/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT + +/* SHA hashing */ +#define CONFIG_CMD_HASH +#define CONFIG_HASH_VERIFY +#define CONFIG_SHA1 +#define CONFIG_SHA256 + +/* Enable Time Command */ +#define CONFIG_CMD_TIME + +#define CONFIG_CMD_BOOTZ + +#endif /* __CONFIG_H */
include/configs/exynos5250-dt.h +7 -280
335 lines not on this page · raw message
include/configs/smdk5420.h new file +50 -0
50 lines not on this page · raw message
Signature · 1 line
1.7.12.4
PATCH v13 11/11 SPL: EXYNOS: Prepare for variable size SPL support
In reply to Rajeshwari S ShindeWhen variable size SPL is used, the BL1 expects the SPL to be encapsulated differently: instead of putting the checksum at a fixed offset in the SPL blob, prepend the blob with a header including the size and the checksum.
The enhancements include
- adding a command line option, '--vs' to indicate the need for the variable size encapsulation
- padding the fixed size encapsulated blob with 0xff instead of random memory contents
- do not silently truncate the input file, report error instead
- no need to explicitly closing files/freeing memory, this all happens on exit; removing cleanups it makes code clearer
- profuse commenting
- modify Makefile to allow enabling the new feature per board
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None.
Changes in V7:
- None.
Changes in V8:
- None
Changes in V9:
- Rebased on latest code.
Changes in V10:
- None
Changes in V11:
- Rebased on latest code.
Changes in V12:
- None
Changes in V13:
- None
include/configs/smdk5420.h | 6 ++ spl/Makefile | 7 +- tools/mkexynosspl.c | 167 +++++++++++++++++++++++++++++++++------------ 3 files changed, 136 insertions(+), 44 deletions(-)
include/configs/smdk5420.h +6 -0
@@ -19,6 +19,8 @@#define CONFIG_ARCH_DEVICE_TREE exynos5420 +#define CONFIG_VAR_SIZE_SPL +#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_TEXT_BASE 0x23E00000
@@ -31,7 +33,11 @@/* select serial console configuration */ #define CONFIG_SERIAL3 /* use SERIAL 3 */ +#ifdef CONFIG_VAR_SIZE_SPL +#define CONFIG_SPL_TEXT_BASE 0x02024410 +#else #define CONFIG_SPL_TEXT_BASE 0x02024400 +#endif #define CONFIG_BOOTCOMMAND "mmc read 20007000 451 2000; bootm 20007000"
spl/Makefile +6 -1
@@ -166,8 +166,13 @@ endif all: $(ALL-y) ifdef CONFIG_SAMSUNG +ifdef CONFIG_VAR_SIZE_SPL +VAR_SIZE_PARAM = --vs +else +VAR_SIZE_PARAM = +endif $(obj)$(BOARD)-spl.bin: $(obj)u-boot-spl.bin - $(OBJTREE)/tools/mk$(BOARD)spl $< $@ + $(OBJTREE)/tools/mk$(BOARD)spl $(VAR_SIZE_PARAM) $< $@ endif $(obj)$(SPL_BIN).bin: $(obj)$(SPL_BIN)
tools/mkexynosspl.c +124 -43
217 lines not on this page · raw message
Signature · 1 line
1.7.12.4
v13 cover EXYNOS5420: Add SMDK5420 board support
In reply to Rajeshwari S ShindeQuoted 53 lines · Rajeshwari S Shinde
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Rajeshwari S Shinde (11):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
EXYNOS5420: Add power register structure.
EXYNOS5420: Add dmc andphy_controlregister structure
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL supportarch/arm/cpu/armv7/exynos/clock.c | 279 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 ++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 60 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 ++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 764 ++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 +++++++- arch/arm/dts/exynos5.dtsi | 198 ++++++ arch/arm/dts/exynos5250.dtsi | 194 +----- arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 52 +- arch/arm/include/asm/arch-exynos/dmc.h | 177 ++++++ arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 408 ++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++ board/samsung/smdk5250/exynos5-dt.c | 350 +---------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 11 + board/samsung/smdk5420/smdk5420.c | 159 +++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 290 +++++++++ include/configs/exynos5250-dt.h | 284 +-------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 +++-- 34 files changed, 5187 insertions(+), 1314 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi
Quoted 9 lines
create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
applied to u-boot-samsung.
Thanks,
Minkyu Kang.
v13 cover EXYNOS5420: Add SMDK5420 board support
Him
Quoted 64 lines · Minkyu Kang
Quoted 53 lines · Rajeshwari S Shinde
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Rajeshwari S Shinde (11):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
EXYNOS5420: Add power register structure.
EXYNOS5420: Add dmc andphy_controlregister structure
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL supportarch/arm/cpu/armv7/exynos/clock.c | 279 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 ++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 60 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 439 ++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 764 ++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 +++++++- arch/arm/dts/exynos5.dtsi | 198 ++++++ arch/arm/dts/exynos5250.dtsi | 194 +----- arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 52 +- arch/arm/include/asm/arch-exynos/dmc.h | 177 ++++++ arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + arch/arm/include/asm/arch-exynos/power.h | 837 +++++++++++++++++++++++++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 408 ++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++ board/samsung/smdk5250/exynos5-dt.c | 350 +---------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 11 + board/samsung/smdk5420/smdk5420.c | 159 +++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 290 +++++++++ include/configs/exynos5250-dt.h | 284 +-------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 +++-- 34 files changed, 5187 insertions(+), 1314 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsiQuoted 9 lines
create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
Quoted 1 line
applied to u-boot-samsung.
Congrats on getting this in!
Regards,
Simon