t2080qds/ddr: update ddr parameters

- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s.
- Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are unrelated to DDR3/3L.

Signed-off-by Shengzhou Liu <[email protected]>

---
Against master branch of git://git.denx.de/u-boot-mpc85xx.git
v3: remain old RDIMM code without updating for now.
v2: throw an error in case of RDIMM.

 board/freescale/t2080qds/ddr.c | 11 ++-----
 board/freescale/t2080qds/ddr.h | 65 +++++++++++++++++-------------------------
 2 files changed, 28 insertions(+), 48 deletions(-)

board/freescale/t2080qds/ddr.c +2 -9

index 5db5d21..4a4d570 100644
@@ -24,7 +24,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
 	ulong ddr_freq;
 
-	if (ctrl_num > 2) {
+	if (ctrl_num > 1) {
 		printf("Not supported controller number %d\n", ctrl_num);
 		return;
 	}

@@ -40,8 +40,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 	else
 		pbsp = udimms[0];
 
-
-	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
 	 * freqency and n_banks specified in board_specific_parameters table.
 	 */
 	ddr_freq = get_ddr_freq(0) / 1000000;

@@ -49,9 +48,6 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 		if (pbsp->n_ranks == pdimm->n_ranks &&
 		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
 			if (ddr_freq <= pbsp->datarate_mhz_high) {
-				popts->cpo_override = pbsp->cpo;
-				popts->write_data_delay =
-					pbsp->write_data_delay;
 				popts->clk_adjust = pbsp->clk_adjust;
 				popts->wrlvl_start = pbsp->wrlvl_start;
 				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;

@@ -69,13 +65,10 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 		printf("for data rate %lu MT/s\n", ddr_freq);
 		printf("Trying to use the highest speed (%u) parameters\n",
 		       pbsp_highest->datarate_mhz_high);
-		popts->cpo_override = pbsp_highest->cpo;
-		popts->write_data_delay = pbsp_highest->write_data_delay;
 		popts->clk_adjust = pbsp_highest->clk_adjust;
 		popts->wrlvl_start = pbsp_highest->wrlvl_start;
 		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
 		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-		popts->twot_en = pbsp_highest->force_2t;
 	} else {
 		panic("DIMM is not supported by this board");
 	}

board/freescale/t2080qds/ddr.h +4 -18

index 964eaad..5828596 100644
@@ -14,9 +14,6 @@ struct board_specific_parameters {
 	u32 wrlvl_start;
 	u32 wrlvl_ctl_2;
 	u32 wrlvl_ctl_3;
-	u32 cpo;
-	u32 write_data_delay;
-	u32 force_2t;
 };
 
 /*

@@ -28,58 +25,48 @@ struct board_specific_parameters {
 static const struct board_specific_parameters udimm0[] = {
 	/*
 	 * memory controller 0
-	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
-	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl |
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |
 	 */
-	{2,  1350, 4, 4,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
-	{2,  1350, 0, 5,     7, 0x0709090b, 0x0c0c0d09,   0xff,    2,  0},
-	{2,  1666, 4, 4,     8, 0x080a0a0d, 0x0d10100b,   0xff,    2,  0},
-	{2,  1666, 0, 5,     7, 0x080a0a0c, 0x0d0d0e0a,   0xff,    2,  0},
-	{2,  1900, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
-	{2,  2140, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
-	{1,  1350, 0, 5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
-	{1,  1700, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
-	{1,  1800, 2, 5,     6, 0x06070709, 0x110a0b08,   0xff,    2,  0},
-	{1,  1866, 2, 4,     6, 0x06060708, 0x09090a07,   0xff,    2,  0},
-	{1,  1900, 2, 4,     6, 0x06060708, 0x09090a07,   0xff,    2,  0},
-	{1,  2000, 2, 4,     8, 0x090a0b0d, 0x0e0f110b,   0xff,    2,  0},
-	{1,  2133, 2, 4,     8, 0x090a0b0d, 0x0e0f110b,   0xff,    2,  0},
+	{2,  1500, 2, 5,     7, 0x0808090a, 0x0b0c0c0a},
+	{2,  1500, 2, 5,     6, 0x07070809, 0x0a0b0b09},