Skip to contentSkip to conversation

Randconfig build failure: screwed dependencies for phy-msm-usb.c

PATCH Superseded Russell King - ARM Linux 5 participants 10 messages Jan 17, 2014 – Feb 18, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

#ifdef CONFIG_PM_SLEEP
static int msm_otg_suspend(struct msm_otg *motg)
{
...
}

static int msm_otg_resume(struct msm_otg *motg) {
...
}
#endif
...
#ifdef CONFIG_PM_RUNTIME
...
static int msm_otg_runtime_suspend(struct device *dev)

{
        struct msm_otg *motg = dev_get_drvdata(dev);

        dev_dbg(dev, "OTG runtime suspend\n");
        return msm_otg_suspend(motg);
}

static int msm_otg_runtime_resume(struct device *dev)

{
        struct msm_otg *motg = dev_get_drvdata(dev);

        dev_dbg(dev, "OTG runtime resume\n");
        return msm_otg_resume(motg);
}

#endif

So, if runtime PM is enabled, but PM sleep isn't, this fails as above. If the msm_otg_* functions are required for runtime PM, they shouldn't be conditional on CONfIG_PM_SLEEP.

Signature · 3 lines
FTTC broadband for 0.8mile line: 5.8Mbps down 500kbps up.  Estimation
in database were 13.1 to 19Mbit for a good line, about 7.5+ for a bad.
Estimate before purchase was "up to 13.2Mbit".
#1 lore raw

PATCH 1/1 usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +26 -31
index 8546c8d..7c7384f 100644
@@ -159,32 +159,6 @@ put_3p3:
 	return rc;
 }
 
-#ifdef CONFIG_PM_SLEEP
-#define USB_PHY_SUSP_DIG_VOL  500000
-static int msm_hsusb_config_vddcx(int high)
-{
-	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
-	int min_vol;
-	int ret;
-
-	if (high)
-		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
-	else
-		min_vol = USB_PHY_SUSP_DIG_VOL;
-
-	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
-	if (ret) {
-		pr_err("%s: unable to set the voltage for regulator "
-			"HSUSB_VDDCX\n", __func__);
-		return ret;
-	}
-
-	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
-
-	return ret;
-}
-#endif
-
 static int msm_hsusb_ldo_set_mode(int on)
 {
 	int ret = 0;
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if defined(CONFIG_PM_SLEEP) || defined(CONFIG_PM_RUNTIME)
+
+#define USB_PHY_SUSP_DIG_VOL  500000
+static int msm_hsusb_config_vddcx(int high)
+{
+	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
+	int min_vol;
+	int ret;
+
+	if (high)
+		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
+	else
+		min_vol = USB_PHY_SUSP_DIG_VOL;
+
+	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
+	if (ret) {
+		pr_err("%s: unable to set the voltage for regulator "
+			"HSUSB_VDDCX\n", __func__);
+		return ret;
+	}
+
+	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
+
+	return ret;
+}
+
 static int msm_otg_suspend(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
@@ -1733,22 +1732,18 @@ static int msm_otg_pm_resume(struct device *dev)
 }
 #endif
 
-#ifdef CONFIG_PM
 static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
 	SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
 				msm_otg_runtime_idle)
 };
-#endif
 
 static struct platform_driver msm_otg_driver = {
 	.remove = msm_otg_remove,
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
-#ifdef CONFIG_PM
 		.pm = &msm_otg_dev_pm_ops,
-#endif
 	},
 };
 
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
#2 lore raw

Re: [PATCH] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Hi Josh,

On 01/17/2014 12:26 PM, Josh Cartwright wrote:

[...]

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 6 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if defined(CONFIG_PM_SLEEP) || defined(CONFIG_PM_RUNTIME)

Why not #ifdef CONFIG_PM here?

Regards,
Christopher

Signature · 3 lines
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by the Linux Foundation.
#3 lore raw

Re: [PATCH] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

In reply to Josh Cartwright
Quoted 23 lines · Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

[...]

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 6 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if defined(CONFIG_PM_SLEEP) || defined(CONFIG_PM_RUNTIME)

nit: you should just use CONFIG_PM here since that is what it's for.

c.f. kernel/power/Kconfig:

config PM

        def_bool y
        depends on PM_SLEEP || PM_RUNTIME

Kevin

#4 lore raw

PATCH v2 1/1 usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
v1->v2: Change conditional to simply CONFIG_PM (thanks ccov and khilman!)

 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +26 -31
index 8546c8d..5b169a7 100644
@@ -159,32 +159,6 @@ put_3p3:
 	return rc;
 }
 
-#ifdef CONFIG_PM_SLEEP
-#define USB_PHY_SUSP_DIG_VOL  500000
-static int msm_hsusb_config_vddcx(int high)
-{
-	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
-	int min_vol;
-	int ret;
-
-	if (high)
-		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
-	else
-		min_vol = USB_PHY_SUSP_DIG_VOL;
-
-	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
-	if (ret) {
-		pr_err("%s: unable to set the voltage for regulator "
-			"HSUSB_VDDCX\n", __func__);
-		return ret;
-	}
-
-	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
-
-	return ret;
-}
-#endif
-
 static int msm_hsusb_ldo_set_mode(int on)
 {
 	int ret = 0;
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if CONFIG_PM
+
+#define USB_PHY_SUSP_DIG_VOL  500000
+static int msm_hsusb_config_vddcx(int high)
+{
+	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
+	int min_vol;
+	int ret;
+
+	if (high)
+		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
+	else
+		min_vol = USB_PHY_SUSP_DIG_VOL;
+
+	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
+	if (ret) {
+		pr_err("%s: unable to set the voltage for regulator "
+			"HSUSB_VDDCX\n", __func__);
+		return ret;
+	}
+
+	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
+
+	return ret;
+}
+
 static int msm_otg_suspend(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
@@ -1733,22 +1732,18 @@ static int msm_otg_pm_resume(struct device *dev)
 }
 #endif
 
-#ifdef CONFIG_PM
 static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
 	SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
 				msm_otg_runtime_idle)
 };
-#endif
 
 static struct platform_driver msm_otg_driver = {
 	.remove = msm_otg_remove,
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
-#ifdef CONFIG_PM
 		.pm = &msm_otg_dev_pm_ops,
-#endif
 	},
 };
 
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
#5 lore raw

Re: [PATCH v2] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Quoted 33 lines · Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
v1->v2: Change conditional to simply CONFIG_PM (thanks ccov and khilman!)

 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +0 -0
index 8546c8d..5b169a7 100644

[..]

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 6 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if CONFIG_PM

*sigh*. This, of course, should have been #ifdef CONFIG_PM. Fixed v3 below.

Thanks,

Josh

-- 8< --
Subject: [PATCH v3] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +26 -31
index 8546c8d..d204f74 100644
@@ -159,32 +159,6 @@ put_3p3:
 	return rc;
 }
 
-#ifdef CONFIG_PM_SLEEP
-#define USB_PHY_SUSP_DIG_VOL  500000
-static int msm_hsusb_config_vddcx(int high)
-{
-	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
-	int min_vol;
-	int ret;
-
-	if (high)
-		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
-	else
-		min_vol = USB_PHY_SUSP_DIG_VOL;
-
-	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
-	if (ret) {
-		pr_err("%s: unable to set the voltage for regulator "
-			"HSUSB_VDDCX\n", __func__);
-		return ret;
-	}
-
-	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
-
-	return ret;
-}
-#endif
-
 static int msm_hsusb_ldo_set_mode(int on)
 {
 	int ret = 0;
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
+
+#define USB_PHY_SUSP_DIG_VOL  500000
+static int msm_hsusb_config_vddcx(int high)
+{
+	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
+	int min_vol;
+	int ret;
+
+	if (high)
+		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
+	else
+		min_vol = USB_PHY_SUSP_DIG_VOL;
+
+	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
+	if (ret) {
+		pr_err("%s: unable to set the voltage for regulator "
+			"HSUSB_VDDCX\n", __func__);
+		return ret;
+	}
+
+	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
+
+	return ret;
+}
+
 static int msm_otg_suspend(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
@@ -1733,22 +1732,18 @@ static int msm_otg_pm_resume(struct device *dev)
 }
 #endif
 
-#ifdef CONFIG_PM
 static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
 	SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
 				msm_otg_runtime_idle)
 };
-#endif
 
 static struct platform_driver msm_otg_driver = {
 	.remove = msm_otg_remove,
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
-#ifdef CONFIG_PM
 		.pm = &msm_otg_dev_pm_ops,
-#endif
 	},
 };
 
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
#6 lore raw

Re: [PATCH v2] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Quoted 39 lines · Josh Cartwright
Quoted 33 lines · Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
v1->v2: Change conditional to simply CONFIG_PM (thanks ccov and khilman!)

 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +0 -0
index 8546c8d..5b169a7 100644

[..]

Quoted 4 lines
drivers/usb/phy/phy-msm-usb.c +0 -0
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
Quoted 5 lines

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 2 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
-#ifdef CONFIG_PM_SLEEP
+#if CONFIG_PM

*sigh*. This, of course, should have been #ifdef CONFIG_PM. Fixed v3 below.

sorry, please git send-email it properly.

Signature · 8 lines
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140218/3f152bfa/attachment.sig>
#7 lore raw

Re: [PATCH v2] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Quoted 40 lines · Felipe Balbi
Quoted 39 lines · Josh Cartwright
Quoted 33 lines · Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
v1->v2: Change conditional to simply CONFIG_PM (thanks ccov and khilman!)

 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +0 -0
index 8546c8d..5b169a7 100644

[..]

Quoted 4 lines
drivers/usb/phy/phy-msm-usb.c +0 -0
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
Quoted 7 lines
Quoted 5 lines

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 2 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
-#ifdef CONFIG_PM_SLEEP
+#if CONFIG_PM

*sigh*. This, of course, should have been #ifdef CONFIG_PM. Fixed v3 below.

sorry, please git send-email it properly.

No problem, will do. FWIW, it's applicable with git am --scissors.

Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
#8 lore raw

Re: [PATCH v2] usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

Quoted 47 lines · Josh Cartwright
Quoted 46 lines · Felipe Balbi
Quoted 44 lines · Josh Cartwright
Quoted 33 lines · Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
v1->v2: Change conditional to simply CONFIG_PM (thanks ccov and khilman!)

 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +0 -0
index 8546c8d..5b169a7 100644

[..]

drivers/usb/phy/phy-msm-usb.c static int msm_otg_reset(struct usb_phy *phy) · line 417

Quoted 6 lines
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#if CONFIG_PM

*sigh*. This, of course, should have been #ifdef CONFIG_PM. Fixed v3 below.

Quoted 3 lines
Quoted 1 line

sorry, please git send-email it properly.

No problem, will do. FWIW, it's applicable with git am --scissors.

ahaa, I didn't know about that option. Thanks :-)

Signature · 8 lines
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140218/78fd0eaf/attachment.sig>
#9 lore raw

PATCH RESEND v3 1/1 usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP

In reply to Josh Cartwright

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common msm_otg_{suspend,resume} routines, however these routines are only being built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also depends on msm_hsusb_config_vddcx(), which is only built when CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend' drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

---
 drivers/usb/phy/phy-msm-usb.c | 57 ++++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/usb/phy/phy-msm-usb.c +26 -31
index 64c9d14e..5b37b81 100644
@@ -159,32 +159,6 @@ put_3p3:
 	return rc;
 }
 
-#ifdef CONFIG_PM_SLEEP
-#define USB_PHY_SUSP_DIG_VOL  500000
-static int msm_hsusb_config_vddcx(int high)
-{
-	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
-	int min_vol;
-	int ret;
-
-	if (high)
-		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
-	else
-		min_vol = USB_PHY_SUSP_DIG_VOL;
-
-	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
-	if (ret) {
-		pr_err("%s: unable to set the voltage for regulator "
-			"HSUSB_VDDCX\n", __func__);
-		return ret;
-	}
-
-	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
-
-	return ret;
-}
-#endif
-
 static int msm_hsusb_ldo_set_mode(int on)
 {
 	int ret = 0;
@@ -440,7 +414,32 @@ static int msm_otg_reset(struct usb_phy *phy)
 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)
 
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
+
+#define USB_PHY_SUSP_DIG_VOL  500000
+static int msm_hsusb_config_vddcx(int high)
+{
+	int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
+	int min_vol;
+	int ret;
+
+	if (high)
+		min_vol = USB_PHY_VDD_DIG_VOL_MIN;
+	else
+		min_vol = USB_PHY_SUSP_DIG_VOL;
+
+	ret = regulator_set_voltage(hsusb_vddcx, min_vol, max_vol);
+	if (ret) {
+		pr_err("%s: unable to set the voltage for regulator "
+			"HSUSB_VDDCX\n", __func__);
+		return ret;
+	}
+
+	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
+
+	return ret;
+}
+
 static int msm_otg_suspend(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
@@ -1734,22 +1733,18 @@ static int msm_otg_pm_resume(struct device *dev)
 }
 #endif
 
-#ifdef CONFIG_PM
 static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
 	SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
 				msm_otg_runtime_idle)
 };
-#endif
 
 static struct platform_driver msm_otg_driver = {
 	.remove = msm_otg_remove,
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
-#ifdef CONFIG_PM
 		.pm = &msm_otg_dev_pm_ops,
-#endif
 	},
 };
 
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation