Skip to contentSkip to conversation

turbostat, servers do not support uncore power register

PATCH Applied Prarit Bhargava 3 participants 4 messages Dec 20, 2013 – Jan 19, 2014 Turbostat utility

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 turbostat, servers do not support uncore power register

Quoted 1 line

From the Intel Software Developer's Manual section 14.7.4,

"For server platforms, PP1 domain is not supported, but its PP0 domain supports the MSR_PP0_PERF_STATUS interface."

When I run 'turbostat ls' I see the following error:

/dev/cpu/0/msr offset 0x641 read failed

because the server doesn't support the MSR_PP1_ENERGY_STATUS register (0x641). This patch implements a get_msr_nowarn() which suppresses the above warning and then sets !RAPL_GFX.

Cc Len Brown <[email protected]>
Cc "Rafael J. Wysocki" <[email protected]>
Cc Josh Triplett <[email protected]>
Cc Kristen Carlson Accardi <[email protected]>
---
 tools/power/x86/turbostat/turbostat.c |   23 ++++++++++++++++++-----
 1 file changed, 18 insertions(+), 5 deletions(-)
tools/power/x86/turbostat/turbostat.c +18 -5
index 9d77f13..ff505c2 100644
@@ -219,7 +219,7 @@ int cpu_migrate(int cpu)
 		return 0;
 }
 
-int get_msr(int cpu, off_t offset, unsigned long long *msr)
+int _get_msr(int cpu, off_t offset, unsigned long long *msr, int warn)
 {
 	ssize_t retval;
 	char pathname[32];
@@ -234,13 +234,25 @@ int get_msr(int cpu, off_t offset, unsigned long long *msr)
 	close(fd);
 
 	if (retval != sizeof *msr) {
-		fprintf(stderr, "%s offset 0x%zx read failed\n", pathname, offset);
+		if (warn)
+			fprintf(stderr, "%s offset 0x%zx read failed\n",
+				pathname, offset);
 		return -1;
 	}
 
 	return 0;
 }
 
+int get_msr(int cpu, off_t offset, unsigned long long *msr)
+{
+	return _get_msr(cpu, offset, msr, 1);
+}
+
+int get_msr_nowarn(int cpu, off_t offset, unsigned long long *msr)
+{
+	return _get_msr(cpu, offset, msr, 0);
+}
+
 void print_header(void)
 {
 	if (show_pkg)
@@ -953,9 +965,10 @@ int get_counters(struct thread_data *t, struct core_data *c, struct pkg_data *p)
 		p->energy_dram = msr & 0xFFFFFFFF;
 	}
 	if (do_rapl & RAPL_GFX) {
-		if (get_msr(cpu, MSR_PP1_ENERGY_STATUS, &msr))
-			return -16;
-		p->energy_gfx = msr & 0xFFFFFFFF;
+		if (get_msr_nowarn(cpu, MSR_PP1_ENERGY_STATUS, &msr))
+			do_rapl &= ~RAPL_GFX; /* unsupported on servers */
+		else
+			p->energy_gfx = msr & 0xFFFFFFFF;
 	}
 	if (do_rapl & RAPL_PKG_PERF_STATUS) {
 		if (get_msr(cpu, MSR_PKG_PERF_STATUS, &msr))
Signature · 1 line
1.7.9.3
#1 lore raw
Quoted 13 lines · Prarit Bhargava

From the Intel Software Developer's Manual section 14.7.4,

"For server platforms, PP1 domain is not supported, but its PP0 domain supports the MSR_PP0_PERF_STATUS interface."

When I run 'turbostat ls' I see the following error:

/dev/cpu/0/msr offset 0x641 read failed

because the server doesn't support the MSR_PP1_ENERGY_STATUS register (0x641). This patch implements a get_msr_nowarn() which suppresses the above warning and then sets !RAPL_GFX.

Quoted 5 lines
Cc Len Brown <[email protected]>
Cc "Rafael J. Wysocki" <[email protected]>
Cc Josh Triplett <[email protected]>
Cc Kristen Carlson Accardi <[email protected]>

Queued up for 3.14, thanks!

Quoted 59 lines
---
 tools/power/x86/turbostat/turbostat.c |   23 ++++++++++++++++++-----
 1 file changed, 18 insertions(+), 5 deletions(-)
tools/power/x86/turbostat/turbostat.c +18 -5
index 9d77f13..ff505c2 100644
@@ -219,7 +219,7 @@ int cpu_migrate(int cpu)
 		return 0;
 }
 
-int get_msr(int cpu, off_t offset, unsigned long long *msr)
+int _get_msr(int cpu, off_t offset, unsigned long long *msr, int warn)
 {
 	ssize_t retval;
 	char pathname[32];
@@ -234,13 +234,25 @@ int get_msr(int cpu, off_t offset, unsigned long long *msr)
 	close(fd);
 
 	if (retval != sizeof *msr) {
-		fprintf(stderr, "%s offset 0x%zx read failed\n", pathname, offset);
+		if (warn)
+			fprintf(stderr, "%s offset 0x%zx read failed\n",
+				pathname, offset);
 		return -1;
 	}
 
 	return 0;
 }
 
+int get_msr(int cpu, off_t offset, unsigned long long *msr)
+{
+	return _get_msr(cpu, offset, msr, 1);
+}
+
+int get_msr_nowarn(int cpu, off_t offset, unsigned long long *msr)
+{
+	return _get_msr(cpu, offset, msr, 0);
+}
+
 void print_header(void)
 {
 	if (show_pkg)
@@ -953,9 +965,10 @@ int get_counters(struct thread_data *t, struct core_data *c, struct pkg_data *p)
 		p->energy_dram = msr & 0xFFFFFFFF;
 	}
 	if (do_rapl & RAPL_GFX) {
-		if (get_msr(cpu, MSR_PP1_ENERGY_STATUS, &msr))
-			return -16;
-		p->energy_gfx = msr & 0xFFFFFFFF;
+		if (get_msr_nowarn(cpu, MSR_PP1_ENERGY_STATUS, &msr))
+			do_rapl &= ~RAPL_GFX; /* unsupported on servers */
+		else
+			p->energy_gfx = msr & 0xFFFFFFFF;
 	}
 	if (do_rapl & RAPL_PKG_PERF_STATUS) {
 		if (get_msr(cpu, MSR_PKG_PERF_STATUS, &msr))
Signature · 2 lines
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.
maintainer
#2 lore raw
In reply to Prarit Bhargava
Quoted 8 lines · Prarit Bhargava

From the Intel Software Developer's Manual section 14.7.4,

"For server platforms, PP1 domain is not supported, but its PP0 domain supports the MSR_PP0_PERF_STATUS interface."

When I run 'turbostat ls' I see the following error:

/dev/cpu/0/msr offset 0x641 read failed

Let me know if you see this when running turbostat v3.6 or later. you can find that version in the linux-next tree.

thanks,
Len Brown, Intel Open Source Technology Center

#3 lore raw
Quoted 6 lines · Len Brown
Quoted 5 lines · Prarit Bhargava

From the Intel Software Developer's Manual section 14.7.4,

"For server platforms, PP1 domain is not supported, but its PP0 domain supports the MSR_PP0_PERF_STATUS interface."

Quoted 7 lines
Quoted 3 lines

When I run 'turbostat ls' I see the following error:

/dev/cpu/0/msr offset 0x641 read failed

Let me know if you see this when running turbostat v3.6 or later. you can find that version in the linux-next tree.

Len, looks like v3.6 works -- I'll do some additional testing to confirm but AFAICT it does work on the affected systems.

P.

Quoted 2 lines

thanks,
Len Brown, Intel Open Source Technology Center