mmc: dw_mmc: remove unused member variable.

PATCH In review Jaehoon Chung 2 participants 3 messages Feb 3, 2014 – Feb 7, 2014

Subsystems (2)

MMC, SD and SDIO Synopsys DesignWare MMC/SD/SDIO driver

lore

Share & tools

lore

Jaehoon Chung

author maintainer

2014-02-03 11:15 UTC #0 lore raw

PATCH v3 4/8 mmc: dw_mmc: remove unused member variable.

Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer.

Signed-off-by Jaehoon Chung <[email protected]>

---
Changelog V3:
- None
Changelog V2:
- None

 drivers/mmc/host/dw_mmc.c  |   33 +++------------------------------
 include/linux/mmc/dw_mmc.h |   14 --------------
 2 files changed, 3 insertions(+), 44 deletions(-)

drivers/mmc/host/dw_mmc.c +3 ~~-30~~

index e7357b8..551dade 100644
@@ -850,8 +850,6 @@ static void __dw_mci_start_request(struct dw_mci *host,
 	u32 cmdflags;
 
 	mrq = slot->mrq;
-	if (host->pdata->select_slot)
-		host->pdata->select_slot(slot->id);
 
 	host->cur_slot = slot;
 	host->mrq = mrq;

@@ -985,17 +983,11 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	switch (ios->power_mode) {
 	case MMC_POWER_UP:
 		set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
-		/* Power up slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, mmc->ocr_avail);
 		regs = mci_readl(slot->host, PWREN);
 		regs |= (1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);
 		break;
 	case MMC_POWER_OFF:
-		/* Power down slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, 0);
 		regs = mci_readl(slot->host, PWREN);
 		regs &= ~(1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);

@@ -1009,13 +1001,10 @@ static int dw_mci_get_ro(struct mmc_host *mmc)
 {
 	int read_only;
 	struct dw_mci_slot *slot = mmc_priv(mmc);
-	struct dw_mci_board *brd = slot->host->pdata;
 
 	/* Use platform get_ro function, else try on board write protect */
 	if (slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
 		read_only = 0;
-	else if (brd->get_ro)
-		read_only = brd->get_ro(slot->id);
 	else if (gpio_is_valid(slot->wp_gpio))
 		read_only = gpio_get_value(slot->wp_gpio);
 	else

@@ -1039,8 +1028,6 @@ static int dw_mci_get_cd(struct mmc_host *mmc)
 	/* Use platform get_cd function, else try onboard card detect */
 	if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
 		present = 1;
-	else if (brd->get_cd)
-		present = !brd->get_cd(slot->id);
 	else if (!IS_ERR_VALUE(gpio_cd))
 		present = gpio_cd;
 	else

@@ -2138,17 +2125,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 		mmc->f_max = freq[1];
 	}
 
-	if (host->pdata->get_ocr)
-		mmc->ocr_avail = host->pdata->get_ocr(id);
-	else
-		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-
-	/*
-	 * Start with slot power disabled, it will be enabled when a card
-	 * is detected.
-	 */
-	if (host->pdata->setpower)
-		host->pdata->setpower(id, 0);
+	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	if (host->pdata->caps)
 		mmc->caps = host->pdata->caps;

@@ -2217,10 +2194,6 @@ err_setup_bus:
 
 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
 {
-	/* Shutdown detect IRQ */
-	if (slot->host->pdata->exit)
-		slot->host->pdata->exit(id);
-
 	/* Debugfs stuff is cleaned up by mmc core */
 	mmc_remove_host(slot->mmc);
 	slot->host->slot[id] = NULL;

@@ -2395,9 +2368,9 @@ int dw_mci_probe(struct dw_mci *host)
 		}
 	}
 
-	if (!host->pdata->select_slot && host->pdata->num_slots > 1) {
+	if (host->pdata->num_slots > 1) {
 		dev_err(host->dev,
-			"Platform data must supply select_slot function\n");
+			"Platform data must supply num_slots.\n");
 		return -ENODEV;
 	}

include/linux/mmc/dw_mmc.h +0 ~~-14~~

index 6ce7d2c..babaea9 100644
@@ -248,20 +248,6 @@ struct dw_mci_board {
 	/* delay in mS before detecting cards after interrupt */
 	u32 detect_delay_ms;
 
-	int (*init)(u32 slot_id, irq_handler_t , void *);
-	int (*get_ro)(u32 slot_id);
-	int (*get_cd)(u32 slot_id);
-	int (*get_ocr)(u32 slot_id);
-	int (*get_bus_wd)(u32 slot_id);
-	/*
-	 * Enable power to selected slot and set voltage to desired level.
-	 * Voltage levels are specified using MMC_VDD_xxx defines defined
-	 * in linux/mmc/host.h file.
-	 */
-	void (*setpower)(u32 slot_id, u32 volt);
-	void (*exit)(u32 slot_id);
-	void (*select_slot)(u32 slot_id);
-
 	struct dw_mci_dma_ops *dma_ops;
 	struct dma_pdata *data;
 	struct block_settings *blk_settings;

Signature · 1 line

1.7.9.5

Seungwon Jeon

2014-02-06 11:23 UTC #1 lore raw

Quoted 4 lines · Jaehoon Chung

Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer.

Above unnecessary line?

Looks good to me.
But just one thing is...
We may need to consider alternative for setpower soon.

Thanks,
Seungwon Jeon

Quoted 138 lines

Signed-off-by Jaehoon Chung <[email protected]>

---
Changelog V3:
- None
Changelog V2:
- None

 drivers/mmc/host/dw_mmc.c  |   33 +++------------------------------
 include/linux/mmc/dw_mmc.h |   14 --------------
 2 files changed, 3 insertions(+), 44 deletions(-)

drivers/mmc/host/dw_mmc.c +3 ~~-30~~

index e7357b8..551dade 100644
@@ -850,8 +850,6 @@ static void __dw_mci_start_request(struct dw_mci *host,
 	u32 cmdflags;
 
 	mrq = slot->mrq;
-	if (host->pdata->select_slot)
-		host->pdata->select_slot(slot->id);
 
 	host->cur_slot = slot;
 	host->mrq = mrq;

@@ -985,17 +983,11 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	switch (ios->power_mode) {
 	case MMC_POWER_UP:
 		set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
-		/* Power up slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, mmc->ocr_avail);
 		regs = mci_readl(slot->host, PWREN);
 		regs |= (1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);
 		break;
 	case MMC_POWER_OFF:
-		/* Power down slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, 0);
 		regs = mci_readl(slot->host, PWREN);
 		regs &= ~(1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);

@@ -1009,13 +1001,10 @@ static int dw_mci_get_ro(struct mmc_host *mmc)
 {
 	int read_only;
 	struct dw_mci_slot *slot = mmc_priv(mmc);
-	struct dw_mci_board *brd = slot->host->pdata;
 
 	/* Use platform get_ro function, else try on board write protect */
 	if (slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
 		read_only = 0;
-	else if (brd->get_ro)
-		read_only = brd->get_ro(slot->id);
 	else if (gpio_is_valid(slot->wp_gpio))
 		read_only = gpio_get_value(slot->wp_gpio);
 	else

@@ -1039,8 +1028,6 @@ static int dw_mci_get_cd(struct mmc_host *mmc)
 	/* Use platform get_cd function, else try onboard card detect */
 	if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
 		present = 1;
-	else if (brd->get_cd)
-		present = !brd->get_cd(slot->id);
 	else if (!IS_ERR_VALUE(gpio_cd))
 		present = gpio_cd;
 	else

@@ -2138,17 +2125,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 		mmc->f_max = freq[1];
 	}
 
-	if (host->pdata->get_ocr)
-		mmc->ocr_avail = host->pdata->get_ocr(id);
-	else
-		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-
-	/*
-	 * Start with slot power disabled, it will be enabled when a card
-	 * is detected.
-	 */
-	if (host->pdata->setpower)
-		host->pdata->setpower(id, 0);
+	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	if (host->pdata->caps)
 		mmc->caps = host->pdata->caps;

@@ -2217,10 +2194,6 @@ err_setup_bus:
 
 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
 {
-	/* Shutdown detect IRQ */
-	if (slot->host->pdata->exit)
-		slot->host->pdata->exit(id);
-
 	/* Debugfs stuff is cleaned up by mmc core */
 	mmc_remove_host(slot->mmc);
 	slot->host->slot[id] = NULL;

@@ -2395,9 +2368,9 @@ int dw_mci_probe(struct dw_mci *host)
 		}
 	}
 
-	if (!host->pdata->select_slot && host->pdata->num_slots > 1) {
+	if (host->pdata->num_slots > 1) {
 		dev_err(host->dev,
-			"Platform data must supply select_slot function\n");
+			"Platform data must supply num_slots.\n");
 		return -ENODEV;
 	}

include/linux/mmc/dw_mmc.h +0 ~~-15~~

index 6ce7d2c..babaea9 100644
@@ -248,20 +248,6 @@ struct dw_mci_board {
 	/* delay in mS before detecting cards after interrupt */
 	u32 detect_delay_ms;
 
-	int (*init)(u32 slot_id, irq_handler_t , void *);
-	int (*get_ro)(u32 slot_id);
-	int (*get_cd)(u32 slot_id);
-	int (*get_ocr)(u32 slot_id);
-	int (*get_bus_wd)(u32 slot_id);
-	/*
-	 * Enable power to selected slot and set voltage to desired level.
-	 * Voltage levels are specified using MMC_VDD_xxx defines defined
-	 * in linux/mmc/host.h file.
-	 */
-	void (*setpower)(u32 slot_id, u32 volt);
-	void (*exit)(u32 slot_id);
-	void (*select_slot)(u32 slot_id);
-
 	struct dw_mci_dma_ops *dma_ops;
 	struct dma_pdata *data;
 	struct block_settings *blk_settings;
--

1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Jaehoon Chung

author maintainer

2014-02-07 02:44 UTC #2 lore raw

Quoted 6 lines · Seungwon Jeon

Quoted 4 lines · Jaehoon Chung
Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer.
Above unnecessary line?

Remove it.

Quoted 4 lines

Looks good to me.
But just one thing is...
We may need to consider alternative for setpower soon.

If we need to consider it, the related code should be located into SoC driver's file

Best Regards,
Jaehoon Chung

Quoted 144 lines

Thanks,
Seungwon Jeon

Quoted 138 lines

Signed-off-by Jaehoon Chung <[email protected]>

---
Changelog V3:
- None
Changelog V2:
- None

 drivers/mmc/host/dw_mmc.c  |   33 +++------------------------------
 include/linux/mmc/dw_mmc.h |   14 --------------
 2 files changed, 3 insertions(+), 44 deletions(-)

drivers/mmc/host/dw_mmc.c +3 ~~-30~~

index e7357b8..551dade 100644
@@ -850,8 +850,6 @@ static void __dw_mci_start_request(struct dw_mci *host,
 	u32 cmdflags;
 
 	mrq = slot->mrq;
-	if (host->pdata->select_slot)
-		host->pdata->select_slot(slot->id);
 
 	host->cur_slot = slot;
 	host->mrq = mrq;

@@ -985,17 +983,11 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	switch (ios->power_mode) {
 	case MMC_POWER_UP:
 		set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
-		/* Power up slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, mmc->ocr_avail);
 		regs = mci_readl(slot->host, PWREN);
 		regs |= (1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);
 		break;
 	case MMC_POWER_OFF:
-		/* Power down slot */
-		if (slot->host->pdata->setpower)
-			slot->host->pdata->setpower(slot->id, 0);
 		regs = mci_readl(slot->host, PWREN);
 		regs &= ~(1 << slot->id);
 		mci_writel(slot->host, PWREN, regs);

@@ -1009,13 +1001,10 @@ static int dw_mci_get_ro(struct mmc_host *mmc)
 {
 	int read_only;
 	struct dw_mci_slot *slot = mmc_priv(mmc);
-	struct dw_mci_board *brd = slot->host->pdata;
 
 	/* Use platform get_ro function, else try on board write protect */
 	if (slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
 		read_only = 0;
-	else if (brd->get_ro)
-		read_only = brd->get_ro(slot->id);
 	else if (gpio_is_valid(slot->wp_gpio))
 		read_only = gpio_get_value(slot->wp_gpio);
 	else

@@ -1039,8 +1028,6 @@ static int dw_mci_get_cd(struct mmc_host *mmc)
 	/* Use platform get_cd function, else try onboard card detect */
 	if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
 		present = 1;
-	else if (brd->get_cd)
-		present = !brd->get_cd(slot->id);
 	else if (!IS_ERR_VALUE(gpio_cd))
 		present = gpio_cd;
 	else

@@ -2138,17 +2125,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 		mmc->f_max = freq[1];
 	}
 
-	if (host->pdata->get_ocr)
-		mmc->ocr_avail = host->pdata->get_ocr(id);
-	else
-		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-
-	/*
-	 * Start with slot power disabled, it will be enabled when a card
-	 * is detected.
-	 */
-	if (host->pdata->setpower)
-		host->pdata->setpower(id, 0);
+	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	if (host->pdata->caps)
 		mmc->caps = host->pdata->caps;

@@ -2217,10 +2194,6 @@ err_setup_bus:
 
 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
 {
-	/* Shutdown detect IRQ */
-	if (slot->host->pdata->exit)
-		slot->host->pdata->exit(id);
-
 	/* Debugfs stuff is cleaned up by mmc core */
 	mmc_remove_host(slot->mmc);
 	slot->host->slot[id] = NULL;

@@ -2395,9 +2368,9 @@ int dw_mci_probe(struct dw_mci *host)
 		}
 	}
 
-	if (!host->pdata->select_slot && host->pdata->num_slots > 1) {
+	if (host->pdata->num_slots > 1) {
 		dev_err(host->dev,
-			"Platform data must supply select_slot function\n");
+			"Platform data must supply num_slots.\n");
 		return -ENODEV;
 	}

include/linux/mmc/dw_mmc.h +0 ~~-15~~

index 6ce7d2c..babaea9 100644
@@ -248,20 +248,6 @@ struct dw_mci_board {
 	/* delay in mS before detecting cards after interrupt */
 	u32 detect_delay_ms;
 
-	int (*init)(u32 slot_id, irq_handler_t , void *);
-	int (*get_ro)(u32 slot_id);
-	int (*get_cd)(u32 slot_id);
-	int (*get_ocr)(u32 slot_id);
-	int (*get_bus_wd)(u32 slot_id);
-	/*
-	 * Enable power to selected slot and set voltage to desired level.
-	 * Voltage levels are specified using MMC_VDD_xxx defines defined
-	 * in linux/mmc/host.h file.
-	 */
-	void (*setpower)(u32 slot_id, u32 volt);
-	void (*exit)(u32 slot_id);
-	void (*select_slot)(u32 slot_id);
-
 	struct dw_mci_dma_ops *dma_ops;
 	struct dma_pdata *data;
 	struct block_settings *blk_settings;
--

1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html