imx6: ensure AHB clock is 132MHz in low freq boot mode
PATCH 1/2 imx6: ensure AHB clock is 132MHz in low freq boot mode
For low freq boot mode(ARM boot up with 396MHz), ROM will not set AHB clock to 132MHz, and the reset value of AHB divider is incorrect which will lead to wrong AHB rate, need to correct it. To enable low freq boot mode, need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL SabreSD board and i.MX6SL EVK board.
--- arch/arm/cpu/armv7/mx6/soc.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm/cpu/armv7/mx6/soc.c +20 -0
@@ -177,10 +177,30 @@ static void imx_set_wdog_powerdown(bool enable)writew (enable, &wdog2->wmcr); } +static void set_ahb_rate (u32 val) +{ +struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR ; +u32 reg, div; + + div =get_periph_clk () / val -1 ; + reg =readl (&mxc_ccm->cbcdr); + +writel ((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK )) | + (div <<MXC_CCM_CBCDR_AHB_PODF_OFFSET ), &mxc_ccm->cbcdr); +} +int arch_cpu_init (void ) {init_aips (); +/* +* When low freq boot is enabled, ROM will not set AHB +* freq, so we need to ensure AHB freq is 132MHz in such +* scenario. +*/ +if (mxc_get_clock (MXC_ARM_CLK ) ==396000000 ) +set_ahb_rate (132000000 ); +imx_set_wdog_powerdown (false);/* Disable PDE bit of WMCR register */ #ifdef CONFIG_APBH_DMA
Signature · 1 line
1.7.9.5
PATCH 2/2 imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2), it will cause warm reset fail, need to clear this MMDC_CHx_MASK field to make sure all the i.MX6 series SOCs reset function work. Otherwise, uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.
--- arch/arm/cpu/armv7/mx6/soc.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/cpu/armv7/mx6/soc.c +11 -0
@@ -189,10 +189,21 @@ static void set_ahb_rate(u32 val) (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr); } +static void clear_mmdc_ch_mask () +{ +struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR ; + +/* Clear MMDC channel mask */ +writel (0 , &mxc_ccm->ccdr); +} +int arch_cpu_init (void ) {init_aips (); +/* Need to clear MMDC_CHx_MASK to make warm reset work. */ +clear_mmdc_ch_mask (); +/* * When low freq boot is enabled, ROM will not set AHB * freq, so we need to ensure AHB freq is 132MHz in such
Signature · 1 line
1.7.9.5
PATCH 2/2 imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
Quoted 7 lines · Anson Huang
Boot ROM may mask
MMDC_CHx_MASKinCCM_CCDR(such as i.MX6SL TO1.2), it will cause warm reset fail, need to clear thisMMDC_CHx_MASKfield to make sure all the i.MX6 series SOCs reset function work. Otherwise, uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.Signed-off-by Anson Huang <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/2 imx6: ensure AHB clock is 132MHz in low freq boot mode
In reply to Anson HuangQuoted 10 lines · Anson Huang
For low freq boot mode(ARM boot up with 396MHz), ROM will not set AHB clock to 132MHz, and the reset value of AHB divider is incorrect which will lead to wrong AHB rate, need to correct it. To enable low freq boot mode, need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL SabreSD board and i.MX6SL EVK board.
Reviewed-by Fabio Estevam <[email protected]>Signed-off-by Anson Huang <[email protected]>---
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================