Skip to contentSkip to conversation

arm: dts: Add support for Compulab sbc-t3530 with cm-t35

PATCH New Stefan Roese 2 participants 2 messages Feb 21, 2014 – Feb 23, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm: dts: Add support for Compulab sbc-t3530 with cm-t35

The cm-t3530 SOM is equipped with the OMAP3530 and does not boot with the cm-t3730 dts file as it used the omap36xx.dtsi. Add a separate dts/dtsi for this board to support it correctly.

I moved some common parts into omap3-cm-t3x30.dtsi. And removed the SDIO/WLAN support for now. As I don't know exactly how this should be done. Perhaps somebody else might jump in here...

Cc Igor Grinberg <[email protected]>
Cc Dmitry Lifshitz <[email protected]>
Cc Tony Lindgren <[email protected]>
---
 arch/arm/boot/dts/Makefile            |  1 +
 arch/arm/boot/dts/omap3-cm-t3530.dts  | 29 +++++++++++++++++++
 arch/arm/boot/dts/omap3-cm-t3730.dts  | 54 ++++-------------------------------
 arch/arm/boot/dts/omap3-cm-t3x30.dtsi | 44 ++++++++++++++++++++++++++++
 arch/arm/boot/dts/omap3-sbc-t3530.dts | 30 +++++++++++++++++++
 5 files changed, 110 insertions(+), 48 deletions(-)
 create mode 100644 arch/arm/boot/dts/omap3-cm-t3530.dts
 create mode 100644 arch/arm/boot/dts/omap3-sbc-t3530.dts
arch/arm/boot/dts/Makefile +1 -0
index 6d1e43d..6fd1b34 100644
@@ -200,6 +200,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
 	omap3-cm-t3730.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
arch/arm/boot/dts/omap3-cm-t3530.dts new file +29 -0
new file mode 100644
index 0000000..35a1fc2
@@ -0,0 +1,29 @@
+/*
+ * Support for CompuLab CM-T3530
+ */
+/dts-v1/;
+
+#include "omap34xx-hs.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3530";
+	compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&smsc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
arch/arm/boot/dts/omap3-cm-t3730.dts +6 -48

71 lines not on this page · raw message

arch/arm/boot/dts/omap3-cm-t3x30.dtsi +44 -0

56 lines not on this page · raw message

arch/arm/boot/dts/omap3-sbc-t3530.dts new file +30 -0
new file mode 100644
index 0000000..b548343
@@ -0,0 +1,30 @@
+/*
+ * Support for CompuLab SBC-T3530 with CM-T3530
+ */
+
+#include "omap3-cm-t3530.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3530 with CM-T3530";
+	compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&smsc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc2_pins>;
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
+			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
Signature · 1 line
1.8.5.5
#1 lore raw

PATCH 1/1 arm: dts: Add support for Compulab sbc-t3530 with cm-t35

Hi Stefan,

Have you seen the series sent by Dmitry on 12-Jan-2014? It is called "ARM: dts: sbc-t3x: add support for more boards", or you can check it out here:
http://www.spinics.net/lists/arm-kernel/msg300078.html

Quoted 246 lines · Stefan Roese

The cm-t3530 SOM is equipped with the OMAP3530 and does not boot with the cm-t3730 dts file as it used the omap36xx.dtsi. Add a separate dts/dtsi for this board to support it correctly.

I moved some common parts into omap3-cm-t3x30.dtsi. And removed the SDIO/WLAN support for now. As I don't know exactly how this should be done. Perhaps somebody else might jump in here...

Cc Igor Grinberg <[email protected]>
Cc Dmitry Lifshitz <[email protected]>
Cc Tony Lindgren <[email protected]>
---
 arch/arm/boot/dts/Makefile            |  1 +
 arch/arm/boot/dts/omap3-cm-t3530.dts  | 29 +++++++++++++++++++
 arch/arm/boot/dts/omap3-cm-t3730.dts  | 54 ++++-------------------------------
 arch/arm/boot/dts/omap3-cm-t3x30.dtsi | 44 ++++++++++++++++++++++++++++
 arch/arm/boot/dts/omap3-sbc-t3530.dts | 30 +++++++++++++++++++
 5 files changed, 110 insertions(+), 48 deletions(-)
 create mode 100644 arch/arm/boot/dts/omap3-cm-t3530.dts
 create mode 100644 arch/arm/boot/dts/omap3-sbc-t3530.dts
arch/arm/boot/dts/Makefile +1 -0
index 6d1e43d..6fd1b34 100644
@@ -200,6 +200,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
 	omap3-cm-t3730.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
arch/arm/boot/dts/omap3-cm-t3530.dts new file +29 -0
new file mode 100644
index 0000000..35a1fc2
@@ -0,0 +1,29 @@
+/*
+ * Support for CompuLab CM-T3530
+ */
+/dts-v1/;
+
+#include "omap34xx-hs.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3530";
+	compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&smsc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
arch/arm/boot/dts/omap3-cm-t3730.dts +6 -48
index 486f4d6..3e05b11 100644
@@ -32,39 +32,14 @@
 };
 
 &omap3_pmx_core {
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
-			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
-			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
-			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
-		>;
-	};
-
 	mmc2_pins: pinmux_mmc2_pins {
 		pinctrl-single,pins = <
-			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
-			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
-			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
-			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
-			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
-		>;
-	};
-
-	smsc1_pins: pinmux_smsc1_pins {
-		pinctrl-single,pins = <
-			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
-			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_clk.sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_cmd.sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_dat0.sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_dat1.sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_dat2.sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)    /* sdmmc2_dat3.sdmmc2_dat3 */
 		>;
 	};
 
@@ -76,13 +51,6 @@
 	};
 };
 
-&mmc1 {
-	vmmc-supply = <&vmmc1>;
-	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
@@ -92,13 +60,3 @@
 	bus-width = <4>;
 	cap-power-off-card;
 };
-
-&smsc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&smsc1_pins>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
-};
arch/arm/boot/dts/omap3-cm-t3x30.dtsi +44 -0
index 3a9f004..0eadd4a 100644
@@ -36,6 +36,33 @@
 	};
 };
 
+&omap3_pmx_core {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	smsc1_pins: pinmux_smsc1_pins {
+		pinctrl-single,pins = <
+			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
+			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>;
 
@@ -83,6 +110,23 @@
 	};
 };
 
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&smsc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
arch/arm/boot/dts/omap3-sbc-t3530.dts new file +30 -0
new file mode 100644
index 0000000..b548343
@@ -0,0 +1,30 @@
+/*
+ * Support for CompuLab SBC-T3530 with CM-T3530
+ */
+
+#include "omap3-cm-t3530.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3530 with CM-T3530";
+	compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&smsc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc2_pins>;
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
+			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
Signature · 2 lines
Regards,
Igor.