ARM: sun6i: Add support for the A31 I2C controller
Subsystems (4)
v2 cover ARM: sun6i: Add support for the A31 I2C controller
Hi everyone,
This patchset adds support the A31 i2c controller. This is mostly the same controller as the one found in the other Allwinner SoCs, except for the interrupts acking.
On the other SoCs using this driver, the interrupts are acked by clearing the INT_FLAG bit in the control register, while on the A31, the interrupt is acked by writing that bit into the control register.
The other difference is that the I2C IP is maintained in reset by a reset controller, so we're adding optionnal support for the reset framework in the driver to deassert the device from reset.
Thanks!
Maxime
Changes from v1:
- Handle EPROBE_DEFER from the reset framework
- Put the device back in reset at remove/failed probe
- Document the newly introduced compatible string
Maxime Ripard (5):
i2c: mv64xxx: Add reset deassert call
i2c: mv64xxx: Add support for the Allwinner A31 I2C driver
ARM: sun6i: Enable the I2C controllers
ARM: sun6i: Enable the I2C muxing options
ARM: sun6i: colombus: Enable the I2C controllers
.../devicetree/bindings/i2c/i2c-mv64xxx.txt | 8 ++- arch/arm/boot/dts/sun6i-a31-colombus.dts | 18 +++++++ arch/arm/boot/dts/sun6i-a31.dtsi | 61 ++++++++++++++++++++++ drivers/i2c/busses/Kconfig | 1 + drivers/i2c/busses/i2c-mv64xxx.c | 31 ++++++++++- 5 files changed, 115 insertions(+), 4 deletions(-)
Signature · 1 line
1.8.4.2
PATCH v2 1/5 i2c: mv64xxx: Add reset deassert call
The Allwinner A31 SoC using that IP has a reset controller maintaining it reset unless told otherwise.
Add some optional reset support to the driver.
--- .../devicetree/bindings/i2c/i2c-mv64xxx.txt | 1 + drivers/i2c/busses/Kconfig | 1 + drivers/i2c/busses/i2c-mv64xxx.c | 21 +++++++++++++++++++-- 3 files changed, 21 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +1 -0
@@ -12,6 +12,7 @@ Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz + - resets : phandle to the parent reset controller Examples:
drivers/i2c/busses/Kconfig +1 -0
@@ -528,6 +528,7 @@ config I2C_MPC config I2C_MV64XXX tristate "Marvell mv64xxx I2C Controller" depends on (MV64X60 || PLAT_ORION || ARCH_SUNXI) + select RESET_CONTROLLER help If you say yes to this option, support will be included for the built-in I2C interface on the Marvell 64xxx line of host bridges.
drivers/i2c/busses/i2c-mv64xxx.c +19 -2
@@ -17,6 +17,7 @@#include <linux/interrupt.h> #include <linux/mv643xx_i2c.h> #include <linux/platform_device.h> +#include <linux/reset.h> #include <linux/io.h> #include <linux/of.h> #include <linux/of_device.h>
@@ -149,6 +150,7 @@ struct mv64xxx_i2c_data {bool offload_enabled;/* 5us delay in order to avoid repeated start timing violation */ bool errata_delay; +struct reset_control *rstc; };static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {
@@ -763,6 +765,16 @@ mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data, } drv_data->irq =irq_of_parse_and_map (np,0 ); + drv_data->rstc =devm_reset_control_get (dev,NULL ); +if (IS_ERR (drv_data->rstc)) { +if (PTR_ERR (drv_data->rstc) == -EPROBE_DEFER ) { + rc = -EPROBE_DEFER ; + goto out; + } + }else { +reset_control_deassert (drv_data->rstc); + } +/* Its not yet defined how timeouts will be specified in device tree. * So hard code the value to 1 second. */
@@ -845,7 +857,7 @@ mv64xxx_i2c_probe(struct platform_device *pd) }if (drv_data->irq <0 ) { rc = -ENXIO ; - goto exit_clk; + goto exit_reset; } drv_data->adapter.dev.parent = &pd->dev;
@@ -865,7 +877,7 @@ mv64xxx_i2c_probe(struct platform_device *pd)dev_err (&drv_data->adapter.dev,"mv64xxx: Can't register intr handler irq%d: %d\n" , drv_data->irq, rc); - goto exit_clk; + goto exit_reset; }else if ((rc =i2c_add_numbered_adapter (&drv_data->adapter)) !=0 ) {dev_err (&drv_data->adapter.dev,"mv64xxx: Can't add i2c adapter, rc: %d\n" , -rc);
@@ -876,6 +888,9 @@ mv64xxx_i2c_probe(struct platform_device *pd) exit_free_irq:free_irq (drv_data->irq, drv_data); +exit_reset: +if (pd->dev.of_node && !IS_ERR (drv_data->rstc)) +reset_control_assert (drv_data->rstc); exit_clk:#if defined(CONFIG_HAVE_CLK )/* Not all platforms have a clk */
@@ -894,6 +909,8 @@ mv64xxx_i2c_remove(struct platform_device *dev)i2c_del_adapter (&drv_data->adapter);free_irq (drv_data->irq, drv_data); +if (dev->dev.of_node && !IS_ERR (drv_data->rstc)) +reset_control_assert (drv_data->rstc);#if defined(CONFIG_HAVE_CLK )/* Not all platforms have a clk */ if (!IS_ERR (drv_data->clk)) {
Signature · 1 line
1.8.4.2
PATCH v2 1/5 i2c: mv64xxx: Add reset deassert call
Hi Maxime,
Quoted 29 lines · Maxime Ripard
The Allwinner A31 SoC using that IP has a reset controller maintaining it reset unless told otherwise.
Add some optional reset support to the driver.
Signed-off-by Maxime Ripard <[email protected]>--- .../devicetree/bindings/i2c/i2c-mv64xxx.txt | 1 + drivers/i2c/busses/Kconfig | 1 + drivers/i2c/busses/i2c-mv64xxx.c | 21 +++++++++++++++++++-- 3 files changed, 21 insertions(+), 2 deletions(-)Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +1
-0@@ -12,6 +12,7 @@ Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz + - resets : phandle to the parent reset controller Examples:drivers/i2c/busses/Kconfig +0
-0
drivers/i2c/busses/Kconfig config I2C_MPC · line 531
Quoted 4 lines
drivers/i2c/busses/Kconfig +1
-0@@ -528,6 +528,7 @@ config I2C_MPC config I2C_MV64XXX tristate "Marvell mv64xxx I2C Controller" depends on (MV64X60 || PLAT_ORION || ARCH_SUNXI) + select RESET_CONTROLLER
This one could maybe just depend on ARCH_SUNXI with something like:
select RESET_CONTROLLER if ARCH_SUNXI
Quoted 24 lines
drivers/i2c/busses/Kconfig +0
-0help If you say yes to this option, support will be included for the built-in I2C interface on the Marvell 64xxx line of host bridges.drivers/i2c/busses/i2c-mv64xxx.c +2
-0@@ -17,6 +17,7 @@#include <linux/interrupt.h> #include <linux/mv643xx_i2c.h> #include <linux/platform_device.h> +#include <linux/reset.h> #include <linux/io.h> #include <linux/of.h> #include <linux/of_device.h> @@ -149,6 +150,7 @@ struct mv64xxx_i2c_data {bool offload_enabled;/* 5us delay in order to avoid repeated start timing violation */ bool errata_delay; +struct reset_control *rstc; };static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {
drivers/i2c/busses/i2c-mv64xxx.c mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data, · line 768
Quoted 4 lines
drivers/i2c/busses/i2c-mv64xxx.c +1
-0@@ -763,6 +765,16 @@ mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data, } drv_data->irq =irq_of_parse_and_map (np,0 ); + drv_data->rstc =devm_reset_control_get (dev,NULL );
Hum ok, you need RESET_CONTROLLER in all case to use it here. As most of the architecture also use RESET_CONTROLLER it is not a big deal to unable it then.
Quoted 42 lines
drivers/i2c/busses/i2c-mv64xxx.c +14
-2+if (IS_ERR (drv_data->rstc)) { +if (PTR_ERR (drv_data->rstc) == -EPROBE_DEFER ) { + rc = -EPROBE_DEFER ; + goto out; + } + }else { +reset_control_deassert (drv_data->rstc); + } +/* Its not yet defined how timeouts will be specified in device tree. * So hard code the value to 1 second. */ @@ -845,7 +857,7 @@ mv64xxx_i2c_probe(struct platform_device *pd) }if (drv_data->irq <0 ) { rc = -ENXIO ; - goto exit_clk; + goto exit_reset; } drv_data->adapter.dev.parent = &pd->dev;@@ -865,7 +877,7 @@ mv64xxx_i2c_probe(struct platform_device *pd)dev_err (&drv_data->adapter.dev,"mv64xxx: Can't register intr handler irq%d: %d\n" , drv_data->irq, rc); - goto exit_clk; + goto exit_reset; }else if ((rc =i2c_add_numbered_adapter (&drv_data->adapter)) !=0 ) {dev_err (&drv_data->adapter.dev,"mv64xxx: Can't add i2c adapter, rc: %d\n" , -rc);@@ -876,6 +888,9 @@ mv64xxx_i2c_probe(struct platform_device *pd) exit_free_irq:free_irq (drv_data->irq, drv_data); +exit_reset: +if (pd->dev.of_node && !IS_ERR (drv_data->rstc)) +reset_control_assert (drv_data->rstc); exit_clk:#if defined(CONFIG_HAVE_CLK )/* Not all platforms have a clk */
drivers/i2c/busses/i2c-mv64xxx.c mv64xxx_i2c_remove(struct platform_device *dev) · line 916
Quoted 8 lines
drivers/i2c/busses/i2c-mv64xxx.c +2
-0@@ -894,6 +909,8 @@ mv64xxx_i2c_remove(struct platform_device *dev)i2c_del_adapter (&drv_data->adapter);free_irq (drv_data->irq, drv_data); +if (dev->dev.of_node && !IS_ERR (drv_data->rstc)) +reset_control_assert (drv_data->rstc);#if defined(CONFIG_HAVE_CLK )/* Not all platforms have a clk */ if (!IS_ERR (drv_data->clk)) {
Everything else looks sensible, I also tested in on an Armada 370. You can add my
Gregory
Signature · 4 lines
Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com
PATCH v2 2/5 i2c: mv64xxx: Add support for the Allwinner A31 I2C driver
In reply to Maxime RipardThe Allwinner A31 I2C controller is almost identical to the one used in the other Allwinner SoCs, except for the fact that it needs to clear the interrupt by setting the INT_FLAGS bit in the control register, instead of clearing it.
--- Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt | 9 ++++++--- drivers/i2c/busses/i2c-mv64xxx.c | 10 ++++++++++ 2 files changed, 16 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +6 -3
@@ -4,15 +4,18 @@ Required properties : - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c" - or "marvell,mv78230-i2c" + - compatible : Should be "marvell,mv64xxx-i2c", "allwinner,sun4i-i2c", + "marvell,mv78230-i2c" or "allwinner,sun6i-a31-i2c" - interrupts : The interrupt number Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz - - resets : phandle to the parent reset controller + + - resets : phandle to the parent reset controller. Mandatory + whenever you're using the "allwinner,sun6i-a31-i2c" + compatible. Examples:
drivers/i2c/busses/i2c-mv64xxx.c +10 -0
@@ -151,6 +151,7 @@ struct mv64xxx_i2c_data {/* 5us delay in order to avoid repeated start timing violation */ bool errata_delay;struct reset_control *rstc; +bool irq_clear_inverted; };static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {
@@ -568,6 +569,11 @@ mv64xxx_i2c_intr(int irq, void *dev_id) status =readl (drv_data->reg_base + drv_data->reg_offsets.status);mv64xxx_i2c_fsm (drv_data, status);mv64xxx_i2c_do_action (drv_data); + +if (drv_data->irq_clear_inverted) +writel (drv_data->cntl_bits |MV64XXX_I2C_REG_CONTROL_IFLG , + drv_data->reg_base + drv_data->reg_offsets.control); + rc =IRQ_HANDLED ; }spin_unlock_irqrestore (&drv_data->lock, flags);
@@ -692,6 +698,7 @@ static const struct i2c_algorithm mv64xxx_i2c_algo = {*/ static const struct of_device_id mv64xxx_i2c_of_match_table[] = { { .compatible ="allwinner,sun4i-i2c" , .data = &mv64xxx_i2c_regs_sun4i}, + { .compatible ="allwinner,sun6i-a31-i2c" , .data = &mv64xxx_i2c_regs_sun4i}, { .compatible ="marvell,mv64xxx-i2c" , .data = &mv64xxx_i2c_regs_mv64xxx}, { .compatible ="marvell,mv78230-i2c" , .data = &mv64xxx_i2c_regs_mv64xxx}, {}
@@ -795,6 +802,9 @@ mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data, drv_data->errata_delay = true; } +if (of_device_is_compatible (np,"allwinner,sun6i-a31-i2c" )) + drv_data->irq_clear_inverted = true; + out:return rc;#endif
Signature · 1 line
1.8.4.2
PATCH v2 2/5 i2c: mv64xxx: Add support for the Allwinner A31 I2C driver
Hi Maxime,
Quoted 3 lines · Maxime Ripard
The Allwinner A31 I2C controller is almost identical to the one used in the other Allwinner SoCs, except for the fact that it needs to clear the interrupt by setting the
INT_FLAGSbit in the control register, instead of clearing it.
This patch doesn't apply on v3.14-rc4. Even by reducing the context the part on i2c-mv64xxx.txt failed to be applied. I removed this part and I reduced the context to one to be able to apply the part in the driver, it allowed me to test it on Armada 370, and then you can also add my:
Gregory
Quoted 76 lines
Signed-off-by Maxime Ripard <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt | 9 ++++++--- drivers/i2c/busses/i2c-mv64xxx.c | 10 ++++++++++ 2 files changed, 16 insertions(+), 3 deletions(-)Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +6
-3@@ -4,15 +4,18 @@ Required properties : - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c" - or "marvell,mv78230-i2c" + - compatible : Should be "marvell,mv64xxx-i2c", "allwinner,sun4i-i2c", + "marvell,mv78230-i2c" or "allwinner,sun6i-a31-i2c" - interrupts : The interrupt number Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz - - resets : phandle to the parent reset controller + + - resets : phandle to the parent reset controller. Mandatory + whenever you're using the "allwinner,sun6i-a31-i2c" + compatible. Examples:drivers/i2c/busses/i2c-mv64xxx.c +10
-0@@ -151,6 +151,7 @@ struct mv64xxx_i2c_data {/* 5us delay in order to avoid repeated start timing violation */ bool errata_delay;struct reset_control *rstc; +bool irq_clear_inverted; };static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {@@ -568,6 +569,11 @@ mv64xxx_i2c_intr(int irq, void *dev_id) status =readl (drv_data->reg_base + drv_data->reg_offsets.status);mv64xxx_i2c_fsm (drv_data, status);mv64xxx_i2c_do_action (drv_data); + +if (drv_data->irq_clear_inverted) +writel (drv_data->cntl_bits |MV64XXX_I2C_REG_CONTROL_IFLG , + drv_data->reg_base + drv_data->reg_offsets.control); + rc =IRQ_HANDLED ; }spin_unlock_irqrestore (&drv_data->lock, flags);@@ -692,6 +698,7 @@ static const struct i2c_algorithm mv64xxx_i2c_algo = {*/ static const struct of_device_id mv64xxx_i2c_of_match_table[] = { { .compatible ="allwinner,sun4i-i2c" , .data = &mv64xxx_i2c_regs_sun4i}, + { .compatible ="allwinner,sun6i-a31-i2c" , .data = &mv64xxx_i2c_regs_sun4i}, { .compatible ="marvell,mv64xxx-i2c" , .data = &mv64xxx_i2c_regs_mv64xxx}, { .compatible ="marvell,mv78230-i2c" , .data = &mv64xxx_i2c_regs_mv64xxx}, {}@@ -795,6 +802,9 @@ mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data, drv_data->errata_delay = true; } +if (of_device_is_compatible (np,"allwinner,sun6i-a31-i2c" )) + drv_data->irq_clear_inverted = true; + out:return rc;#endif
Signature · 4 lines
Gregory Clement, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com
PATCH v2 3/5 ARM: sun6i: Enable the I2C controllers
In reply to Maxime RipardThe A31 has 4 I2C controllers that are the same than the one in the other Allwinner SoCs, except for the fact that they are asserted in reset by the reset unit.
Add these i2c controllers to the DTSI.
--- arch/arm/boot/dts/sun6i-a31.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+)
arch/arm/boot/dts/sun6i-a31.dtsi +40 -0
@@ -312,6 +312,46 @@ status = "disabled"; }; + i2c0: i2c at 01c2ac00 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <0 6 4>; + clocks = <&apb2_gates 0>; + clock-frequency = <100000>; + resets = <&apb2_rst 0>; + status = "disabled"; + }; + + i2c1: i2c at 01c2b000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <0 7 4>; + clocks = <&apb2_gates 1>; + clock-frequency = <100000>; + resets = <&apb2_rst 1>; + status = "disabled"; + }; + + i2c2: i2c at 01c2b400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <0 8 4>; + clocks = <&apb2_gates 2>; + clock-frequency = <100000>; + resets = <&apb2_rst 2>; + status = "disabled"; + }; + + i2c3: i2c at 01c2b800 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = <0 9 4>; + clocks = <&apb2_gates 3>; + clock-frequency = <100000>; + resets = <&apb2_rst 3>; + status = "disabled"; + }; + gic: interrupt-controller at 01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>,
Signature · 1 line
1.8.4.2
PATCH v2 4/5 ARM: sun6i: Enable the I2C muxing options
In reply to Maxime RipardThe i2c controllers have a few muxing options on the A31. Enable the ones found in the A31 Colombus board.
--- arch/arm/boot/dts/sun6i-a31.dtsi | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm/boot/dts/sun6i-a31.dtsi +21 -0
@@ -210,6 +210,27 @@ allwinner,drive = <0>; allwinner,pull = <0>; }; + + i2c0_pins_a: i2c0 at 0 { + allwinner,pins = "PH14", "PH15"; + allwinner,function = "i2c0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c1_pins_a: i2c1 at 0 { + allwinner,pins = "PH16", "PH17"; + allwinner,function = "i2c1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c2_pins_a: i2c2 at 0 { + allwinner,pins = "PH18", "PH19"; + allwinner,function = "i2c2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; ahb1_rst: reset at 01c202c0 {
Signature · 1 line
1.8.4.2
PATCH v2 5/5 ARM: sun6i: colombus: Enable the I2C controllers
In reply to Maxime RipardThe A31 Colombus board has 3 I2C controllers that should be usable. However, the first one is not working for some reason on the hardware I have been able to test it on, while it should really be the same controller. Enable the i2c1 and i2c2 busses, and mark i2c0 as in failure in the DT.
--- arch/arm/boot/dts/sun6i-a31-colombus.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm/boot/dts/sun6i-a31-colombus.dts +18 -0
@@ -28,5 +28,23 @@ pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + + i2c0: i2c at 01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "fail"; + }; + + i2c1: i2c at 01c2b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + }; + + i2c2: i2c at 01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; }; };
Signature · 1 line
1.8.4.2
v2 cover ARM: sun6i: Add support for the A31 I2C controller
In reply to Maxime RipardHi Wolfram,
Quoted 6 lines · Maxime Ripard
Hi everyone,
This patchset adds support the A31 i2c controller. This is mostly the same controller as the one found in the other Allwinner SoCs, except for the interrupts acking.
Quoted 7 lines
On the other SoCs using this driver, the interrupts are acked by clearing the
INT_FLAGbit in the control register, while on the A31, the interrupt is acked by writing that bit into the control register.The other difference is that the I2C IP is maintained in reset by a reset controller, so we're adding optionnal support for the reset framework in the driver to deassert the device from reset.
Do you have any comments on this?
Thanks,
Maxime
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140127/4998546e/attachment-0001.sig>
v2 cover ARM: sun6i: Add support for the A31 I2C controller
Quoted 13 lines · Maxime Ripard
Hi Wolfram,
Quoted 10 lines · Maxime Ripard
Hi everyone,
This patchset adds support the A31 i2c controller. This is mostly the same controller as the one found in the other Allwinner SoCs, except for the interrupts acking.
On the other SoCs using this driver, the interrupts are acked by clearing the
INT_FLAGbit in the control register, while on the A31, the interrupt is acked by writing that bit into the control register.
Quoted 5 lines
Quoted 3 lines
The other difference is that the I2C IP is maintained in reset by a reset controller, so we're adding optionnal support for the reset framework in the driver to deassert the device from reset.
Do you have any comments on this?
Ping?
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140206/34c79c1b/attachment.sig>
v2 cover ARM: sun6i: Add support for the A31 I2C controller
In reply to Maxime RipardHi Wolfram,
Quoted 6 lines · Maxime Ripard
Hi everyone,
This patchset adds support the A31 i2c controller. This is mostly the same controller as the one found in the other Allwinner SoCs, except for the interrupts acking.
Quoted 7 lines
On the other SoCs using this driver, the interrupts are acked by clearing the
INT_FLAGbit in the control register, while on the A31, the interrupt is acked by writing that bit into the control register.The other difference is that the I2C IP is maintained in reset by a reset controller, so we're adding optionnal support for the reset framework in the driver to deassert the device from reset.
It's been over a month now, and no sign of life from you on this patch so far... Should I just take this patchset through my tree? :)
Thanks,
Maxime
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140217/cee08417/attachment.sig>
v2 cover ARM: sun6i: Add support for the A31 I2C controller
Quoted 3 lines
It's been over a month now, and no sign of life from you on this patch so far... Should I just take this patchset through my tree? :)
Nope.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140217/d3ebaef5/attachment.sig>
v2 cover ARM: sun6i: Add support for the A31 I2C controller
Quoted 5 lines · Wolfram Sang
Quoted 3 lines
It's been over a month now, and no sign of life from you on this patch so far... Should I just take this patchset through my tree? :)
Nope.
Then please review those 40 lines of code.
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140217/2a276873/attachment.sig>
v2 cover ARM: sun6i: Add support for the A31 I2C controller
Quoted 8 lines · Maxime Ripard
Quoted 5 lines · Wolfram Sang
Quoted 3 lines
It's been over a month now, and no sign of life from you on this patch so far... Should I just take this patchset through my tree? :)
Nope.
Then please review those 40 lines of code.
They are due when they are due. If you want to speed it up, you are very welcome to review patches on the i2c mailing list.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140217/3c19f1d4/attachment-0001.sig>