ath9k_hw: toggle weak signal detection in AP mode on older chipsets
PATCH 1/2 ath9k_hw: toggle weak signal detection in AP mode on older chipsets
The commit 80b4205b "ath9k: Fix OFDM weak signal detection for AP mode" prevented weak signal detection changes from taking effect in AP mode on all chipsets, claiming it is "not allowed".
The main reason for not disabling weak signal detection in AP mode is that typically beacon RSSI is used to track whether it is needed to boost range, and this is unavailable in AP mode for obvious reasons.
The problem with not disabling weak signal detection is that older chipsets are very sensitive to high PHY error counts. When faced with heavy noise, this can lead to an excessive amount of "Failed to stop TX DMA" errors in the field.
--- drivers/net/wireless/ath/ath9k/ani.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/net/wireless/ath/ath9k/ani.c +10 -8
@@ -176,16 +176,18 @@ static void ath9k_hw_set_ofdm_nil(struct ath_hw *ah, u8 immunityLevel,if (ah->opmode ==NL80211_IFTYPE_STATION &&BEACON_RSSI (ah) <=ATH9K_ANI_RSSI_THR_HIGH ) weak_sig = true; -/* -* OFDM Weak signal detection is always enabled for AP mode. +* Newer chipsets are better at dealing with high PHY error counts - +* keep weak signal detection enabled when no RSSI threshold is +* available to determine if it is needed (mode != STA) */ -if (ah->opmode !=NL80211_IFTYPE_AP && - aniState->ofdmWeakSigDetect != weak_sig) { -ath9k_hw_ani_control (ah, -ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , - entry_ofdm->ofdm_weak_signal_on); - } +else if (AR_SREV_9300_20_OR_LATER (ah) && + ah->opmode !=NL80211_IFTYPE_STATION ) + weak_sig = true; + +if (aniState->ofdmWeakSigDetect != weak_sig) +ath9k_hw_ani_control (ah,ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , + weak_sig);if (aniState->ofdmNoiseImmunityLevel >=ATH9K_ANI_OFDM_DEF_LEVEL ) { ah->config.ofdm_trig_high =ATH9K_ANI_OFDM_TRIG_HIGH ;
Signature · 1 line
1.8.3.4 (Apple Git-47)
PATCH 2/2 ath9k_hw: tweak noise immunity thresholds for older chipsets
Older chipsets are more sensitive to high PHY error counts, and the current noise immunity thresholds were based on tests run at QCA with newer chipsets.
This patch brings back the values from the old ANI implementation for old chipsets, and it also disables weak signal detection on an earlier noise immunity level, to improve overall radio stability on affected devices.
--- drivers/net/wireless/ath/ath9k/ani.c | 23 +++++++++++++++++++---- drivers/net/wireless/ath/ath9k/ani.h | 4 ++++ 2 files changed, 23 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath9k/ani.c +19 -4
@@ -185,10 +185,18 @@ static void ath9k_hw_set_ofdm_nil(struct ath_hw *ah, u8 immunityLevel, ah->opmode != NL80211_IFTYPE_STATION) weak_sig = true; +/* Older chipsets are more sensitive to high PHY error counts */ + else if (!AR_SREV_9300_20_OR_LATER(ah) && + aniState->ofdmNoiseImmunityLevel >= 8) + weak_sig = false; +if (aniState->ofdmWeakSigDetect != weak_sig)ath9k_hw_ani_control (ah,ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , weak_sig); +if (!AR_SREV_9300_20_OR_LATER (ah)) +return ; +if (aniState->ofdmNoiseImmunityLevel >=ATH9K_ANI_OFDM_DEF_LEVEL ) { ah->config.ofdm_trig_high =ATH9K_ANI_OFDM_TRIG_HIGH ; ah->config.ofdm_trig_low =ATH9K_ANI_OFDM_TRIG_LOW_ABOVE_INI ;
@@ -485,10 +493,17 @@ void ath9k_hw_ani_init(struct ath_hw *ah)ath_dbg (common,ANI ,"Initialize ANI\n" ); - ah->config.ofdm_trig_high =ATH9K_ANI_OFDM_TRIG_HIGH ; - ah->config.ofdm_trig_low =ATH9K_ANI_OFDM_TRIG_LOW ; - ah->config.cck_trig_high =ATH9K_ANI_CCK_TRIG_HIGH ; - ah->config.cck_trig_low =ATH9K_ANI_CCK_TRIG_LOW ; +if (AR_SREV_9300_20_OR_LATER (ah)) { + ah->config.ofdm_trig_high =ATH9K_ANI_OFDM_TRIG_HIGH ; + ah->config.ofdm_trig_low =ATH9K_ANI_OFDM_TRIG_LOW ; + ah->config.cck_trig_high =ATH9K_ANI_CCK_TRIG_HIGH ; + ah->config.cck_trig_low =ATH9K_ANI_CCK_TRIG_LOW ; + }else { + ah->config.ofdm_trig_high =ATH9K_ANI_OFDM_TRIG_HIGH_OLD ; + ah->config.ofdm_trig_low =ATH9K_ANI_OFDM_TRIG_LOW_OLD ; + ah->config.cck_trig_high =ATH9K_ANI_CCK_TRIG_HIGH_OLD ; + ah->config.cck_trig_low =ATH9K_ANI_CCK_TRIG_LOW_OLD ; + } ani->spurImmunityLevel =ATH9K_ANI_SPUR_IMMUNE_LVL ; ani->firstepLevel =ATH9K_ANI_FIRSTEP_LVL ;
drivers/net/wireless/ath/ath9k/ani.h +4 -0
@@ -22,12 +22,16 @@/* units are errors per second */ #define ATH9K_ANI_OFDM_TRIG_HIGH 3500#define ATH9K_ANI_OFDM_TRIG_HIGH_BELOW_INI 1000 +#define ATH9K_ANI_OFDM_TRIG_HIGH_OLD 500#define ATH9K_ANI_OFDM_TRIG_LOW 400#define ATH9K_ANI_OFDM_TRIG_LOW_ABOVE_INI 900 +#define ATH9K_ANI_OFDM_TRIG_LOW_OLD 200#define ATH9K_ANI_CCK_TRIG_HIGH 600 +#define ATH9K_ANI_CCK_TRIG_HIGH_OLD 200#define ATH9K_ANI_CCK_TRIG_LOW 300 +#define ATH9K_ANI_CCK_TRIG_LOW_OLD 100#define ATH9K_ANI_SPUR_IMMUNE_LVL 3#define ATH9K_ANI_FIRSTEP_LVL 2
Signature · 1 line
1.8.3.4 (Apple Git-47)
Re: [PATCH 2/2] ath9k_hw: tweak noise immunity thresholds for older chipsets
Quoted 8 lines · Felix Fietkau
Older chipsets are more sensitive to high PHY error counts, and the current noise immunity thresholds were based on tests run at QCA with newer chipsets.
This patch brings back the values from the old ANI implementation for old chipsets, and it also disables weak signal detection on an earlier noise immunity level, to improve overall radio stability on affected devices.
Which devices ?
Since the old values were used in the old ANI implementation, I am not sure how just retrofitting them into the new ANI algorithm can improve things...
Sujith
Re: [PATCH 2/2] ath9k_hw: tweak noise immunity thresholds for older chipsets
Quoted 11 lines · Sujith Manoharan
Quoted 8 lines · Felix Fietkau
Older chipsets are more sensitive to high PHY error counts, and the current noise immunity thresholds were based on tests run at QCA with newer chipsets.
This patch brings back the values from the old ANI implementation for old chipsets, and it also disables weak signal detection on an earlier noise immunity level, to improve overall radio stability on affected devices.
Which devices ?
Reproduced on AR913x, suspected on AR928x, probably other affected devices as well.
Quoted 2 lines
Since the old values were used in the old ANI implementation, I am not sure how just retrofitting them into the new ANI algorithm can improve things...
Semantically, the values are compatible. The algorithm is similar enough that this works just fine. The patch has gone through some testing that showed a visible stability improvement.
- Felix
drivers/net/wireless/ath/ath9k/ani.c static void ath9k_hw_set_ofdm_nil(struct ath_hw *ah, u8 immunityLevel, · line 190
Quoted 13 lines · Felix Fietkau
drivers/net/wireless/ath/ath9k/ani.c +7
-6-if (ah->opmode !=NL80211_IFTYPE_AP && - aniState->ofdmWeakSigDetect != weak_sig) { -ath9k_hw_ani_control (ah, -ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , - entry_ofdm->ofdm_weak_signal_on); - } +else if (AR_SREV_9300_20_OR_LATER (ah) && + ah->opmode !=NL80211_IFTYPE_STATION ) + weak_sig = true; + +if (aniState->ofdmWeakSigDetect != weak_sig) +ath9k_hw_ani_control (ah,ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , + weak_sig);
Any reason why this has been changed to disregard the WS-DET parameter from ofdm_level_table[] ?
Sujith
Quoted 17 lines · Sujith Manoharan
drivers/net/wireless/ath/ath9k/ani.c static void ath9k_hw_set_ofdm_nil(struct ath_hw *ah, u8 immunityLevel, · line 190
Quoted 13 lines · Felix Fietkau
drivers/net/wireless/ath/ath9k/ani.c +7
-6-if (ah->opmode !=NL80211_IFTYPE_AP && - aniState->ofdmWeakSigDetect != weak_sig) { -ath9k_hw_ani_control (ah, -ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , - entry_ofdm->ofdm_weak_signal_on); - } +else if (AR_SREV_9300_20_OR_LATER (ah) && + ah->opmode !=NL80211_IFTYPE_STATION ) + weak_sig = true; + +if (aniState->ofdmWeakSigDetect != weak_sig) +ath9k_hw_ani_control (ah,ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION , + weak_sig);Any reason why this has been changed to disregard the WS-DET parameter from ofdm_level_table[] ?
It doesn't disregard it - weak_sig is initialized to the value of that parameter. Comparing aniState->ofdmWeakSigDetect against weak_sig, but then passing entry_ofdm->ofdm_weak_signal_on is buggy.
- Felix