mmc: mmci: Improve DT support

index 771c60a..b0b81ac 100644
@@ -23,6 +23,7 @@
 #include <linux/mmc/pm.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
+#include <linux/mmc/slot-gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/clk.h>
 #include <linux/scatterlist.h>

@@ -1326,35 +1327,18 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	pm_runtime_put_autosuspend(mmc_dev(mmc));
 }
 
-static int mmci_get_ro(struct mmc_host *mmc)
-{
-	struct mmci_host *host = mmc_priv(mmc);
-
-	if (host->gpio_wp == -ENOSYS)
-		return -ENOSYS;
-
-	return gpio_get_value_cansleep(host->gpio_wp);
-}
-
 static int mmci_get_cd(struct mmc_host *mmc)
 {
 	struct mmci_host *host = mmc_priv(mmc);
 	struct mmci_platform_data *plat = host->plat;
-	unsigned int status;
+	unsigned int status = mmc_gpio_get_cd(mmc);
 
-	if (host->gpio_cd == -ENOSYS) {
+	if (status == -ENOSYS) {
 		if (!plat->status)
 			return 1; /* Assume always present */
 
 		status = plat->status(mmc_dev(host->mmc));
-	} else
-		status = !!gpio_get_value_cansleep(host->gpio_cd)
-			^ plat->cd_invert;
-
-	/*
-	 * Use positive logic throughout - status is zero for no card,
-	 * non-zero for card inserted.
-	 */
+	}
 	return status;
 }
 

@@ -1391,21 +1375,12 @@ static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
 	return ret;
 }
 
-static irqreturn_t mmci_cd_irq(int irq, void *dev_id)
-{
-	struct mmci_host *host = dev_id;
-
-	mmc_detect_change(host->mmc, msecs_to_jiffies(500));
-
-	return IRQ_HANDLED;
-}
-
 static struct mmc_host_ops mmci_ops = {
 	.request	= mmci_request,
 	.pre_req	= mmci_pre_request,
 	.post_req	= mmci_post_request,
 	.set_ios	= mmci_set_ios,
-	.get_ro		= mmci_get_ro,
+	.get_ro		= mmc_gpio_get_ro,
 	.get_cd		= mmci_get_cd,
 	.start_signal_voltage_switch = mmci_sig_volt_switch,
 };

@@ -1494,10 +1469,6 @@ static int mmci_probe(struct amba_device *dev,
 	host = mmc_priv(mmc);
 	host->mmc = mmc;
 
-	host->gpio_wp = -ENOSYS;
-	host->gpio_cd = -ENOSYS;
-	host->gpio_cd_irq = -1;
-
 	host->hw_designer = amba_manf(dev);
 	host->hw_revision = amba_rev(dev);
 	dev_dbg(mmc_dev(mmc), "designer ID = 0x%02x\n", host->hw_designer);

@@ -1568,6 +1539,9 @@ static int mmci_probe(struct amba_device *dev,
 
 	mmc->caps = plat->capabilities;
 	mmc->caps2 = plat->capabilities2;
+	if (!plat->cd_invert)
+		mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
+	mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
 
 	if (variant->busy_detect) {
 		mmci_ops.card_busy = mmci_card_busy;

@@ -1621,49 +1595,23 @@ static int mmci_probe(struct amba_device *dev,
 		goto err_gpio_cd;
 	}
 	if (gpio_is_valid(plat->gpio_cd)) {
-		ret = gpio_request(plat->gpio_cd, DRIVER_NAME " (cd)");
-		if (ret == 0)
-			ret = gpio_direction_input(plat->gpio_cd);
-		if (ret == 0)
-			host->gpio_cd = plat->gpio_cd;
-		else if (ret != -ENOSYS)
+		ret = mmc_gpio_request_cd(mmc, plat->gpio_cd, 0);
+		if (ret)
 			goto err_gpio_cd;
-
-		/*
-		 * A gpio pin that will detect cards when inserted and removed
-		 * will most likely want to trigger on the edges if it is
-		 * 0 when ejected and 1 when inserted (or mutatis mutandis
-		 * for the inverted case) so we request triggers on both
-		 * edges.
-		 */
-		ret = request_any_context_irq(gpio_to_irq(plat->gpio_cd),
-				mmci_cd_irq,
-				IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-				DRIVER_NAME " (cd)", host);
-		if (ret >= 0)
-			host->gpio_cd_irq = gpio_to_irq(plat->gpio_cd);
 	}
 	if (plat->gpio_wp == -EPROBE_DEFER) {
 		ret = -EPROBE_DEFER;
-		goto err_gpio_wp;
+		goto err_gpio_cd;
 	}
 	if (gpio_is_valid(plat->gpio_wp)) {
-		ret = gpio_request(plat->gpio_wp, DRIVER_NAME " (wp)");
-		if (ret == 0)
-			ret = gpio_direction_input(plat->gpio_wp);
-		if (ret == 0)
-			host->gpio_wp = plat->gpio_wp;
-		else if (ret != -ENOSYS)
-			goto err_gpio_wp;
+		ret = mmc_gpio_request_ro(mmc, plat->gpio_wp);
+		if (ret)
+			goto err_gpio_cd;
 	}
 
-	if ((host->plat->status || host->gpio_cd != -ENOSYS)
-	    && host->gpio_cd_irq < 0)
-		mmc->caps |= MMC_CAP_NEEDS_POLL;
-
 	ret = request_irq(dev->irq[0], mmci_irq, IRQF_SHARED, DRIVER_NAME " (cmd)", host);
 	if (ret)
-		goto unmap;
+		goto err_gpio_cd;
 
 	if (!dev->irq[1])
 		host->singleirq = true;

@@ -1695,14 +1643,6 @@ static int mmci_probe(struct amba_device *dev,
 
  irq0_free:
 	free_irq(dev->irq[0], host);
- unmap:
-	if (host->gpio_wp != -ENOSYS)
-		gpio_free(host->gpio_wp);
- err_gpio_wp:
-	if (host->gpio_cd_irq >= 0)
-		free_irq(host->gpio_cd_irq, host);
-	if (host->gpio_cd != -ENOSYS)
-		gpio_free(host->gpio_cd);
  err_gpio_cd:
 	iounmap(host->base);
  clk_disable:

@@ -1741,13 +1681,6 @@ static int mmci_remove(struct amba_device *dev)
 		if (!host->singleirq)
 			free_irq(dev->irq[1], host);
 
-		if (host->gpio_wp != -ENOSYS)
-			gpio_free(host->gpio_wp);
-		if (host->gpio_cd_irq >= 0)
-			free_irq(host->gpio_cd_irq, host);
-		if (host->gpio_cd != -ENOSYS)
-			gpio_free(host->gpio_cd);
-
 		iounmap(host->base);
 		clk_disable_unprepare(host->clk);
 

index 58b1b88..8fc5814 100644
@@ -176,9 +176,6 @@ struct mmci_host {
 	struct mmc_data		*data;
 	struct mmc_host		*mmc;
 	struct clk		*clk;
-	int			gpio_cd;
-	int			gpio_wp;
-	int			gpio_cd_irq;
 	bool			singleirq;
 
 	spinlock_t		lock;

index b0b81ac..d6f20ba 100644
@@ -13,6 +13,7 @@
 #include <linux/init.h>
 #include <linux/ioport.h>
 #include <linux/device.h>
+#include <linux/io.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>

@@ -1456,15 +1457,13 @@ static int mmci_probe(struct amba_device *dev,
 	if (np)
 		mmci_dt_populate_generic_pdata(np, plat);
 
-	ret = amba_request_regions(dev, DRIVER_NAME);
-	if (ret)
-		goto out;
+	if (!devm_request_mem_region(&dev->dev, dev->res.start,
+				resource_size(&dev->res), DRIVER_NAME))
+		return -ENOMEM;
 
 	mmc = mmc_alloc_host(sizeof(struct mmci_host), &dev->dev);
-	if (!mmc) {
-		ret = -ENOMEM;
-		goto rel_regions;
-	}
+	if (!mmc)
+		return -ENOMEM;
 
 	host = mmc_priv(mmc);
 	host->mmc = mmc;

@@ -1500,8 +1499,10 @@ static int mmci_probe(struct amba_device *dev,
 		dev_dbg(mmc_dev(mmc), "eventual mclk rate: %u Hz\n",
 			host->mclk);
 	}
+
 	host->phybase = dev->res.start;
-	host->base = ioremap(dev->res.start, resource_size(&dev->res));
+	host->base = devm_ioremap(&dev->dev, host->phybase,
+				resource_size(&dev->res));
 	if (!host->base) {
 		ret = -ENOMEM;
 		goto clk_disable;

@@ -1592,34 +1593,35 @@ static int mmci_probe(struct amba_device *dev,
 
 	if (plat->gpio_cd == -EPROBE_DEFER) {
 		ret = -EPROBE_DEFER;
-		goto err_gpio_cd;
+		goto clk_disable;
 	}
 	if (gpio_is_valid(plat->gpio_cd)) {
 		ret = mmc_gpio_request_cd(mmc, plat->gpio_cd, 0);
 		if (ret)
-			goto err_gpio_cd;
+			goto clk_disable;
 	}
 	if (plat->gpio_wp == -EPROBE_DEFER) {
 		ret = -EPROBE_DEFER;
-		goto err_gpio_cd;
+		goto clk_disable;
 	}
 	if (gpio_is_valid(plat->gpio_wp)) {
 		ret = mmc_gpio_request_ro(mmc, plat->gpio_wp);
 		if (ret)
-			goto err_gpio_cd;
+			goto clk_disable;
 	}
 
-	ret = request_irq(dev->irq[0], mmci_irq, IRQF_SHARED, DRIVER_NAME " (cmd)", host);
+	ret = devm_request_irq(&dev->dev, dev->irq[0], mmci_irq, IRQF_SHARED,
+			DRIVER_NAME " (cmd)", host);
 	if (ret)
-		goto err_gpio_cd;
+		goto clk_disable;
 
 	if (!dev->irq[1])
 		host->singleirq = true;
 	else {
-		ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED,
-				  DRIVER_NAME " (pio)", host);
+		ret = devm_request_irq(&dev->dev, dev->irq[1], mmci_pio_irq,
+				IRQF_SHARED, DRIVER_NAME " (pio)", host);
 		if (ret)
-			goto irq0_free;
+			goto clk_disable;
 	}
 
 	writel(MCI_IRQENABLE, host->base + MMCIMASK0);

@@ -1641,17 +1643,10 @@ static int mmci_probe(struct amba_device *dev,
 
 	return 0;
 
- irq0_free:
-	free_irq(dev->irq[0], host);
- err_gpio_cd:
-	iounmap(host->base);
  clk_disable:
 	clk_disable_unprepare(host->clk);
  host_free:
 	mmc_free_host(mmc);
- rel_regions:
-	amba_release_regions(dev);
- out:
 	return ret;
 }
 

@@ -1677,16 +1672,8 @@ static int mmci_remove(struct amba_device *dev)
 		writel(0, host->base + MMCIDATACTRL);
 
 		mmci_dma_release(host);
-		free_irq(dev->irq[0], host);
-		if (!host->singleirq)
-			free_irq(dev->irq[1], host);
-
-		iounmap(host->base);
 		clk_disable_unprepare(host->clk);
-
 		mmc_free_host(mmc);
-
-		amba_release_regions(dev);
 	}
 
 	return 0;

index d6f20ba..c99ec88 100644
@@ -1392,6 +1392,17 @@ static void mmci_dt_populate_generic_pdata(struct device_node *np,
 {
 	int bus_width = 0;
 
+	if (of_get_property(np, "st,sig-dir-dat0", NULL))
+		pdata->sigdir |= MCI_ST_DATA0DIREN;
+	if (of_get_property(np, "st,sig-dir-dat2", NULL))
+		pdata->sigdir |= MCI_ST_DATA2DIREN;
+	if (of_get_property(np, "st,sig-dir-dat31", NULL))
+		pdata->sigdir |= MCI_ST_DATA31DIREN;
+	if (of_get_property(np, "st,sig-dir-dat74", NULL))
+		pdata->sigdir |= MCI_ST_DATA74DIREN;
+	if (of_get_property(np, "st,sig-dir-cmd", NULL))
+		pdata->sigdir |= MCI_ST_CMDDIREN;
+
 	pdata->gpio_wp = of_get_named_gpio(np, "wp-gpios", 0);
 	pdata->gpio_cd = of_get_named_gpio(np, "cd-gpios", 0);
 

index c99ec88..3663bc15 100644
@@ -1402,6 +1402,8 @@ static void mmci_dt_populate_generic_pdata(struct device_node *np,
 		pdata->sigdir |= MCI_ST_DATA74DIREN;
 	if (of_get_property(np, "st,sig-dir-cmd", NULL))
 		pdata->sigdir |= MCI_ST_CMDDIREN;
+	if (of_get_property(np, "st,sig-pin-fbclk", NULL))
+		pdata->sigdir |= MCI_ST_FBCLKEN;
 
 	pdata->gpio_wp = of_get_named_gpio(np, "wp-gpios", 0);
 	pdata->gpio_cd = of_get_named_gpio(np, "cd-gpios", 0);

index 3663bc15..892921d 100644
@@ -1386,12 +1386,9 @@ static struct mmc_host_ops mmci_ops = {
 	.start_signal_voltage_switch = mmci_sig_volt_switch,
 };
 
-#ifdef CONFIG_OF
 static void mmci_dt_populate_generic_pdata(struct device_node *np,
 					struct mmci_platform_data *pdata)
 {
-	int bus_width = 0;
-
 	if (of_get_property(np, "st,sig-dir-dat0", NULL))
 		pdata->sigdir |= MCI_ST_DATA0DIREN;
 	if (of_get_property(np, "st,sig-dir-dat2", NULL))

@@ -1404,46 +1401,22 @@ static void mmci_dt_populate_generic_pdata(struct device_node *np,
 		pdata->sigdir |= MCI_ST_CMDDIREN;
 	if (of_get_property(np, "st,sig-pin-fbclk", NULL))
 		pdata->sigdir |= MCI_ST_FBCLKEN;
+}
 
-	pdata->gpio_wp = of_get_named_gpio(np, "wp-gpios", 0);
-	pdata->gpio_cd = of_get_named_gpio(np, "cd-gpios", 0);
-
-	if (of_get_property(np, "cd-inverted", NULL))
-		pdata->cd_invert = true;
-	else
-		pdata->cd_invert = false;
+static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)
+{
+	int ret = mmc_of_parse(mmc);
 
-	of_property_read_u32(np, "max-frequency", &pdata->f_max);
-	if (!pdata->f_max)
-		pr_warn("%s has no 'max-frequency' property\n", np->full_name);
+	if (ret)
+		return ret;
 
 	if (of_get_property(np, "mmc-cap-mmc-highspeed", NULL))
-		pdata->capabilities |= MMC_CAP_MMC_HIGHSPEED;
+		mmc->caps |= MMC_CAP_MMC_HIGHSPEED;
 	if (of_get_property(np, "mmc-cap-sd-highspeed", NULL))
-		pdata->capabilities |= MMC_CAP_SD_HIGHSPEED;
+		mmc->caps |= MMC_CAP_SD_HIGHSPEED;
 
-	of_property_read_u32(np, "bus-width", &bus_width);
-	switch (bus_width) {
-	case 0 :
-		/* No bus-width supplied. */
-		break;
-	case 4 :
-		pdata->capabilities |= MMC_CAP_4_BIT_DATA;
-		break;
-	case 8 :
-		pdata->capabilities |= MMC_CAP_8_BIT_DATA;
-		break;
-	default :
-		pr_warn("%s: Unsupported bus width\n", np->full_name);
-	}
-}
-#else
-static void mmci_dt_populate_generic_pdata(struct device_node *np,
-					struct mmci_platform_data *pdata)
-{
-	return;
+	return 0;
 }
-#endif
 
 static int mmci_probe(struct amba_device *dev,
 	const struct amba_id *id)

@@ -1478,6 +1451,10 @@ static int mmci_probe(struct amba_device *dev,
 	if (!mmc)
 		return -ENOMEM;
 
+	ret = mmci_of_parse(np, mmc);
+	if (ret)
+		goto host_free;
+
 	host = mmc_priv(mmc);
 	host->mmc = mmc;
 

@@ -1531,14 +1508,15 @@ static int mmci_probe(struct amba_device *dev,
 	else
 		mmc->f_min = DIV_ROUND_UP(host->mclk, 512);
 	/*
-	 * If the platform data supplies a maximum operating
-	 * frequency, this takes precedence. Else, we fall back
-	 * to using the module parameter, which has a (low)
-	 * default value in case it is not specified. Either
-	 * value must not exceed the clock rate into the block,
-	 * of course.
+	 * If no maximum operating frequency is supplied, fall back to use
+	 * the module parameter, which has a (low) default value in case it
+	 * is not specified. Either value must not exceed the clock rate into
+	 * the block, of course. Also note that DT takes precedence over
+	 * platform data.
 	 */
-	if (plat->f_max)
+	if (mmc->f_max)
+		mmc->f_max = min(host->mclk, mmc->f_max);
+	else if (plat->f_max)
 		mmc->f_max = min(host->mclk, plat->f_max);
 	else
 		mmc->f_max = min(host->mclk, fmax);

@@ -1551,11 +1529,14 @@ static int mmci_probe(struct amba_device *dev,
 	else if (plat->ocr_mask)
 		dev_warn(mmc_dev(mmc), "Platform OCR mask is ignored\n");
 
-	mmc->caps = plat->capabilities;
-	mmc->caps2 = plat->capabilities2;
-	if (!plat->cd_invert)
-		mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
-	mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
+	/* DT takes precedence over platform data. */
+	mmc->caps = np ? mmc->caps : plat->capabilities;
+	mmc->caps2 = np ? mmc->caps2 : plat->capabilities2;
+	if (!np) {
+		if (!plat->cd_invert)
+			mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
+		mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
+	}
 
 	if (variant->busy_detect) {
 		mmci_ops.card_busy = mmci_card_busy;

@@ -1567,7 +1548,7 @@ static int mmci_probe(struct amba_device *dev,
 	mmc->ops = &mmci_ops;
 
 	/* We support these PM capabilities. */
-	mmc->pm_caps = MMC_PM_KEEP_POWER;
+	mmc->pm_caps |= MMC_PM_KEEP_POWER;
 
 	/*
 	 * We can do SGIO

@@ -1604,20 +1585,13 @@ static int mmci_probe(struct amba_device *dev,
 	writel(0, host->base + MMCIMASK1);
 	writel(0xfff, host->base + MMCICLEAR);
 
-	if (plat->gpio_cd == -EPROBE_DEFER) {
-		ret = -EPROBE_DEFER;
-		goto clk_disable;
-	}
-	if (gpio_is_valid(plat->gpio_cd)) {
+	/* If DT, cd/wp gpios must be supplied through it. */
+	if (!np && gpio_is_valid(plat->gpio_cd)) {
 		ret = mmc_gpio_request_cd(mmc, plat->gpio_cd, 0);
 		if (ret)
 			goto clk_disable;
 	}
-	if (plat->gpio_wp == -EPROBE_DEFER) {
-		ret = -EPROBE_DEFER;
-		goto clk_disable;
-	}
-	if (gpio_is_valid(plat->gpio_wp)) {
+	if (!np && gpio_is_valid(plat->gpio_wp)) {
 		ret = mmc_gpio_request_ro(mmc, plat->gpio_wp);
 		if (ret)
 			goto clk_disable;

index 892921d..8db90fd 100644
@@ -1538,6 +1538,9 @@ static int mmci_probe(struct amba_device *dev,
 		mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
 	}
 
+	/* We support these capabilities. */
+	mmc->caps |= MMC_CAP_CMD23;
+
 	if (variant->busy_detect) {
 		mmci_ops.card_busy = mmci_card_busy;
 		mmci_write_datactrlreg(host, MCI_ST_DPSM_BUSYMODE);

166 lines not on this page · raw message

index 32cc0d8..7c7b0ad 100644
@@ -8,12 +8,7 @@
 #define __BOARD_MOP500_H
 
 #include <linux/platform_data/asoc-ux500-msp.h>
-#include <linux/amba/mmci.h>
 
-extern struct mmci_platform_data mop500_sdi0_data;
-extern struct mmci_platform_data mop500_sdi1_data;
-extern struct mmci_platform_data mop500_sdi2_data;
-extern struct mmci_platform_data mop500_sdi4_data;
 extern struct msp_i2s_platform_data msp0_platform_data;
 extern struct msp_i2s_platform_data msp1_platform_data;
 extern struct msp_i2s_platform_data msp2_platform_data;

index 8820f60..fa308f0 100644
@@ -146,10 +146,6 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	/* Requires call-back bindings. */
 	OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
 	/* Requires DMA bindings. */
-	OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0",  &mop500_sdi0_data),
-	OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1",  &mop500_sdi1_data),
-	OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2",  &mop500_sdi2_data),
-	OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4",  &mop500_sdi4_data),
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
 		       "ux500-msp-i2s.0", &msp0_platform_data),
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,

index 8db90fd..4a3f582 100644
@@ -1287,7 +1287,7 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		 * indicating signal direction for the signals in
 		 * the SD/MMC bus and feedback-clock usage.
 		 */
-		pwr |= host->plat->sigdir;
+		pwr |= host->pwr_reg_add;
 
 		if (ios->bus_width == MMC_BUS_WIDTH_4)
 			pwr &= ~MCI_ST_DATA74DIREN;

@@ -1386,29 +1386,26 @@ static struct mmc_host_ops mmci_ops = {
 	.start_signal_voltage_switch = mmci_sig_volt_switch,
 };
 
-static void mmci_dt_populate_generic_pdata(struct device_node *np,
-					struct mmci_platform_data *pdata)
+static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)
 {
+	struct mmci_host *host = mmc_priv(mmc);
+	int ret = mmc_of_parse(mmc);
+
+	if (ret)
+		return ret;
+
 	if (of_get_property(np, "st,sig-dir-dat0", NULL))
-		pdata->sigdir |= MCI_ST_DATA0DIREN;
+		host->pwr_reg_add |= MCI_ST_DATA0DIREN;
 	if (of_get_property(np, "st,sig-dir-dat2", NULL))
-		pdata->sigdir |= MCI_ST_DATA2DIREN;
+		host->pwr_reg_add |= MCI_ST_DATA2DIREN;
 	if (of_get_property(np, "st,sig-dir-dat31", NULL))
-		pdata->sigdir |= MCI_ST_DATA31DIREN;
+		host->pwr_reg_add |= MCI_ST_DATA31DIREN;
 	if (of_get_property(np, "st,sig-dir-dat74", NULL))
-		pdata->sigdir |= MCI_ST_DATA74DIREN;
+		host->pwr_reg_add |= MCI_ST_DATA74DIREN;
 	if (of_get_property(np, "st,sig-dir-cmd", NULL))
-		pdata->sigdir |= MCI_ST_CMDDIREN;
+		host->pwr_reg_add |= MCI_ST_CMDDIREN;
 	if (of_get_property(np, "st,sig-pin-fbclk", NULL))
-		pdata->sigdir |= MCI_ST_FBCLKEN;
-}
-
-static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)
-{
-	int ret = mmc_of_parse(mmc);
-
-	if (ret)
-		return ret;
+		host->pwr_reg_add |= MCI_ST_FBCLKEN;
 
 	if (of_get_property(np, "mmc-cap-mmc-highspeed", NULL))
 		mmc->caps |= MMC_CAP_MMC_HIGHSPEED;

@@ -1440,9 +1437,6 @@ static int mmci_probe(struct amba_device *dev,
 			return -ENOMEM;
 	}
 
-	if (np)
-		mmci_dt_populate_generic_pdata(np, plat);
-
 	if (!devm_request_mem_region(&dev->dev, dev->res.start,
 				resource_size(&dev->res), DRIVER_NAME))
 		return -ENOMEM;

index 8fc5814..347d942 100644
@@ -13,6 +13,16 @@
 #define MCI_PWR_ON		0x03
 #define MCI_OD			(1 << 6)
 #define MCI_ROD			(1 << 7)
+/*
+ * The ST Micro version does not have ROD and reuse the voltage registers for
+ * direction settings.
+ */
+#define MCI_ST_DATA2DIREN	(1 << 2)
+#define MCI_ST_CMDDIREN		(1 << 3)
+#define MCI_ST_DATA0DIREN	(1 << 4)
+#define MCI_ST_DATA31DIREN	(1 << 5)
+#define MCI_ST_FBCLKEN		(1 << 7)
+#define MCI_ST_DATA74DIREN	(1 << 8)
 
 #define MMCICLOCK		0x004
 #define MCI_CLK_ENABLE		(1 << 8)

@@ -183,6 +193,7 @@ struct mmci_host {
 	unsigned int		mclk;
 	unsigned int		cclk;
 	u32			pwr_reg;
+	u32			pwr_reg_add;
 	u32			clk_reg;
 	u32			datactrl_reg;
 	u32			busy_status;

index 32a89cf..0d3ff95 100644
@@ -6,19 +6,6 @@
 
 #include <linux/mmc/host.h>
 
-
-/*
- * These defines is places here due to access is needed from machine
- * configuration files. The ST Micro version does not have ROD and
- * reuse the voltage registers for direction settings.
- */
-#define MCI_ST_DATA2DIREN	(1 << 2)
-#define MCI_ST_CMDDIREN		(1 << 3)
-#define MCI_ST_DATA0DIREN	(1 << 4)
-#define MCI_ST_DATA31DIREN	(1 << 5)
-#define MCI_ST_FBCLKEN		(1 << 7)
-#define MCI_ST_DATA74DIREN	(1 << 8)
-
 /* Just some dummy forwarding */
 struct dma_chan;
 

@@ -45,8 +32,6 @@ struct dma_chan;
  * @capabilities: the capabilities of the block as implemented in
  * this platform, signify anything MMC_CAP_* from mmc/host.h
  * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h
- * @sigdir: a bit field indicating for what bits in the MMC bus the host
- * should enable signal direction indication.
  * @dma_filter: function used to select an appropriate RX and TX
  * DMA channel to be used for DMA, if and only if you're deploying the
  * generic DMA engine

@@ -69,7 +54,6 @@ struct mmci_platform_data {
 	bool	cd_invert;
 	unsigned long capabilities;
 	unsigned long capabilities2;
-	u32 sigdir;
 	bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
 	void *dma_rx_param;
 	void *dma_tx_param;

index 4a3f582..601e816 100644
@@ -1524,8 +1524,6 @@ static int mmci_probe(struct amba_device *dev,
 		dev_warn(mmc_dev(mmc), "Platform OCR mask is ignored\n");
 
 	/* DT takes precedence over platform data. */
-	mmc->caps = np ? mmc->caps : plat->capabilities;
-	mmc->caps2 = np ? mmc->caps2 : plat->capabilities2;
 	if (!np) {
 		if (!plat->cd_invert)
 			mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;

index 0d3ff95..b992fc9 100644
@@ -29,9 +29,6 @@ struct dma_chan;
  * @gpio_wp: read this GPIO pin to see if the card is write protected
  * @gpio_cd: read this GPIO pin to detect card insertion
  * @cd_invert: true if the gpio_cd pin value is active low
- * @capabilities: the capabilities of the block as implemented in
- * this platform, signify anything MMC_CAP_* from mmc/host.h
- * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h
  * @dma_filter: function used to select an appropriate RX and TX
  * DMA channel to be used for DMA, if and only if you're deploying the
  * generic DMA engine

@@ -52,8 +49,6 @@ struct mmci_platform_data {
 	int	gpio_wp;
 	int	gpio_cd;
 	bool	cd_invert;
-	unsigned long capabilities;
-	unsigned long capabilities2;
 	bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
 	void *dma_rx_param;
 	void *dma_tx_param;

index 601e816..5cb5a81 100644
@@ -366,7 +366,6 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
 #ifdef CONFIG_DMA_ENGINE
 static void mmci_dma_setup(struct mmci_host *host)
 {
-	struct mmci_platform_data *plat = host->plat;
 	const char *rxname, *txname;
 	dma_cap_mask_t mask;
 

@@ -380,25 +379,6 @@ static void mmci_dma_setup(struct mmci_host *host)
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
 
-	if (plat && plat->dma_filter) {
-		if (!host->dma_rx_channel && plat->dma_rx_param) {
-			host->dma_rx_channel = dma_request_channel(mask,
-							   plat->dma_filter,
-							   plat->dma_rx_param);
-			/* E.g if no DMA hardware is present */
-			if (!host->dma_rx_channel)
-				dev_err(mmc_dev(host->mmc), "no RX DMA channel\n");
-		}
-
-		if (!host->dma_tx_channel && plat->dma_tx_param) {
-			host->dma_tx_channel = dma_request_channel(mask,
-							   plat->dma_filter,
-							   plat->dma_tx_param);
-			if (!host->dma_tx_channel)
-				dev_warn(mmc_dev(host->mmc), "no TX DMA channel\n");
-		}
-	}
-
 	/*
 	 * If only an RX channel is specified, the driver will
 	 * attempt to use it bidirectionally, however if it is

@@ -446,11 +426,9 @@ static void mmci_dma_setup(struct mmci_host *host)
  */
 static inline void mmci_dma_release(struct mmci_host *host)
 {
-	struct mmci_platform_data *plat = host->plat;
-
 	if (host->dma_rx_channel)
 		dma_release_channel(host->dma_rx_channel);
-	if (host->dma_tx_channel && plat->dma_tx_param)
+	if (host->dma_tx_channel)
 		dma_release_channel(host->dma_tx_channel);
 	host->dma_rx_channel = host->dma_tx_channel = NULL;
 }

index b992fc9..bf339ff 100644
@@ -6,9 +6,6 @@
 
 #include <linux/mmc/host.h>
 
-/* Just some dummy forwarding */
-struct dma_chan;
-
 /**
  * struct mmci_platform_data - platform configuration for the MMCI
  * (also known as PL180) block.

@@ -29,17 +26,6 @@ struct dma_chan;
  * @gpio_wp: read this GPIO pin to see if the card is write protected
  * @gpio_cd: read this GPIO pin to detect card insertion
  * @cd_invert: true if the gpio_cd pin value is active low
- * @dma_filter: function used to select an appropriate RX and TX
- * DMA channel to be used for DMA, if and only if you're deploying the
- * generic DMA engine
- * @dma_rx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate RX channel. If
- * there is a bidirectional RX+TX channel, then just specify
- * this and leave dma_tx_param set to NULL
- * @dma_tx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate TX channel. If this
- * is NULL the driver will attempt to use the RX channel as a
- * bidirectional channel
  */
 struct mmci_platform_data {
 	unsigned int f_max;

@@ -49,9 +35,6 @@ struct mmci_platform_data {
 	int	gpio_wp;
 	int	gpio_cd;
 	bool	cd_invert;
-	bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
-	void *dma_rx_param;
-	void *dma_tx_param;
 };
 
 #endif

index 5cb5a81..3e4bfec 100644
@@ -1483,13 +1483,10 @@ static int mmci_probe(struct amba_device *dev,
 	 * If no maximum operating frequency is supplied, fall back to use
 	 * the module parameter, which has a (low) default value in case it
 	 * is not specified. Either value must not exceed the clock rate into
-	 * the block, of course. Also note that DT takes precedence over
-	 * platform data.
+	 * the block, of course.
 	 */
 	if (mmc->f_max)
 		mmc->f_max = min(host->mclk, mmc->f_max);
-	else if (plat->f_max)
-		mmc->f_max = min(host->mclk, plat->f_max);
 	else
 		mmc->f_max = min(host->mclk, fmax);
 	dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);

index bf339ff..8c98113 100644
@@ -9,9 +9,6 @@
 /**
  * struct mmci_platform_data - platform configuration for the MMCI
  * (also known as PL180) block.
- * @f_max: the maximum operational frequency for this host in this
- * platform configuration. When this is specified it takes precedence
- * over the module parameter for the same frequency.
  * @ocr_mask: available voltages on the 4 pins from the block, this
  * is ignored if a regulator is used, see the MMC_VDD_* masks in
  * mmc/host.h

@@ -28,7 +25,6 @@
  * @cd_invert: true if the gpio_cd pin value is active low
  */
 struct mmci_platform_data {
-	unsigned int f_max;
 	unsigned int ocr_mask;
 	int (*ios_handler)(struct device *, struct mmc_ios *);
 	unsigned int (*status)(struct device *);