ARM: tegra: define Jetson TK1 regulators
Subsystems (2)
PATCH 1/1 ARM: tegra: define Jetson TK1 regulators
From: Stephen Warren <[email protected]>
These are mostly identical to the Venice2 regulator definitions, since the board designs are very similar. Differences are:
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This change should likely be propagated to Venice2 for completeness, although it will have no practical effect there since various other regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason is because it's used to driver the UART level-shifter; without this, I see a brief period of UART corruption during cold boots.I suspect this change needs to be propagated to Venice2, and we simply haven't noticed the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.
--- arch/arm/boot/dts/tegra124-jetson-tk1.dts | 230 ++++++++++++++++++++++++++++++ 1 file changed, 230 insertions(+)
arch/arm/boot/dts/tegra124-jetson-tk1.dts +230 -0
@@ -1426,6 +1426,155 @@ bias-high-impedance; }; }; + + regulators { + vsup-sd2-supply = <&vdd_5v0_sys>; + vsup-sd3-supply = <&vdd_5v0_sys>; + vsup-sd4-supply = <&vdd_5v0_sys>; + vsup-sd5-supply = <&vdd_5v0_sys>; + vin-ldo0-supply = <&vdd_1v35_lp0>; + vin-ldo1-6-supply = <&vdd_3v3_run>; + vin-ldo2-5-7-supply = <&vddio_1v8>; + vin-ldo3-4-supply = <&vdd_3v3_sys>; + vin-ldo9-10-supply = <&vdd_5v0_sys>; + vin-ldo11-supply = <&vdd_3v3_run>; + + sd0 { + regulator-name = "+VDD_CPU_AP"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-always-on; + regulator-boot-on; + ams,external-control = <2>; + }; + + sd1 { + regulator-name = "+VDD_CORE"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-min-microamp = <2500000>; + regulator-max-microamp = <2500000>; + regulator-always-on; + regulator-boot-on; + ams,external-control = <1>; + }; + + vdd_1v35_lp0: sd2 { + regulator-name = "+1.35V_LP0(sd2)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + sd3 { + regulator-name = "+1.35V_LP0(sd3)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + sd4 { + regulator-name = "+1.05V_RUN"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + vddio_1v8: sd5 { + regulator-name = "+1.8V_VDDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + sd6 { + regulator-name = "+VDD_GPU_AP"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1200000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo0 { + regulator-name = "+1.05V_RUN_AVDD"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-boot-on; + regulator-always-on; + ams,external-control = <1>; + }; + + ldo1 { + regulator-name = "+1.8V_RUN_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2 { + regulator-name = "+1.2V_GEN_AVDD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3 { + regulator-name = "+1.05V_LP0_VDD_RTC"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + ams,enable-tracking; + }; + + ldo4 { + regulator-name = "+2.8V_RUN_CAM"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo5 { + regulator-name = "+1.2V_RUN_CAM_FRONT"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vddio_sdmmc3: ldo6 { + regulator-name = "+VDDIO_SDMMC3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7 { + regulator-name = "+1.05V_RUN_CAM_REAR"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo9 { + regulator-name = "+3.3V_RUN_TOUCH"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo10 { + regulator-name = "+2.8V_RUN_CAM_AF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo11 { + regulator-name = "+1.8V_RUN_VPP_FUSE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; }; };
@@ -1462,6 +1611,7 @@ cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>; }; /* eMMC */
@@ -1525,6 +1675,72 @@ #address-cells = <1>; #size-cells = <0>; + vdd_mux: regulator at 0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "+VDD_MUX"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_5v0_sys: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "+5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_sys: regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "+3.3V_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_run: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "+3.3V_RUN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + }; + + vdd_3v3_hdmi: regulator at 4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_usb1_vbus: regulator at 7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "+USB0_VBUS_SW"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + vdd_usb3_vbus: regulator at 8 { compatible = "regulator-fixed"; reg = <8>;
@@ -1534,6 +1750,20 @@ gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; enable-active-high; gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_3v3_lp0: regulator at 10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "+3.3V_LP0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; }; };
Signature · 1 line
1.8.1.5
Stephen Warren
AppliedPATCH 1/1 ARM: tegra: define Jetson TK1 regulators
Quoted 5 lines · Stephen Warren
From: Stephen Warren <[email protected]>
These are mostly identical to the Venice2 regulator definitions, since the board designs are very similar. Differences are:
Quoted 12 lines
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This change should likely be propagated to Venice2 for completeness, although it will have no practical effect there since various other regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason is because it's used to driver the UART level-shifter; without this, I see a brief period of UART corruption during cold boots.I suspect this change needs to be propagated to Venice2, and we simply haven't noticed the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.
I have applied this to Tegra's for-3.16/dt branch.
PATCH 1/1 ARM: tegra: define Jetson TK1 regulators
In reply to Stephen WarrenQuoted 184 lines · Stephen Warren
From: Stephen Warren <[email protected]>
These are mostly identical to the Venice2 regulator definitions, since the board designs are very similar. Differences are:
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This change should likely be propagated to Venice2 for completeness, although it will have no practical effect there since various other regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason is because it's used to driver the UART level-shifter; without this, I see a brief period of UART corruption during cold boots.I suspect this change needs to be propagated to Venice2, and we simply haven't noticed the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.Signed-off-by Stephen Warren <[email protected]>--- arch/arm/boot/dts/tegra124-jetson-tk1.dts | 230 ++++++++++++++++++++++++++++++ 1 file changed, 230 insertions(+)arch/arm/boot/dts/tegra124-jetson-tk1.dts +149
-0@@ -1426,6 +1426,155 @@ bias-high-impedance; }; }; + + regulators { + vsup-sd2-supply = <&vdd_5v0_sys>; + vsup-sd3-supply = <&vdd_5v0_sys>; + vsup-sd4-supply = <&vdd_5v0_sys>; + vsup-sd5-supply = <&vdd_5v0_sys>; + vin-ldo0-supply = <&vdd_1v35_lp0>; + vin-ldo1-6-supply = <&vdd_3v3_run>; + vin-ldo2-5-7-supply = <&vddio_1v8>; + vin-ldo3-4-supply = <&vdd_3v3_sys>; + vin-ldo9-10-supply = <&vdd_5v0_sys>; + vin-ldo11-supply = <&vdd_3v3_run>; + + sd0 { + regulator-name = "+VDD_CPU_AP"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-always-on; + regulator-boot-on; + ams,external-control = <2>; + }; + + sd1 { + regulator-name = "+VDD_CORE"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-min-microamp = <2500000>; + regulator-max-microamp = <2500000>; + regulator-always-on; + regulator-boot-on; + ams,external-control = <1>; + }; + + vdd_1v35_lp0: sd2 { + regulator-name = "+1.35V_LP0(sd2)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + sd3 { + regulator-name = "+1.35V_LP0(sd3)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + sd4 { + regulator-name = "+1.05V_RUN"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + vddio_1v8: sd5 { + regulator-name = "+1.8V_VDDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + sd6 { + regulator-name = "+VDD_GPU_AP"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1200000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo0 { + regulator-name = "+1.05V_RUN_AVDD"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-boot-on; + regulator-always-on; + ams,external-control = <1>; + }; + + ldo1 { + regulator-name = "+1.8V_RUN_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2 { + regulator-name = "+1.2V_GEN_AVDD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3 { + regulator-name = "+1.05V_LP0_VDD_RTC"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + ams,enable-tracking; + }; + + ldo4 { + regulator-name = "+2.8V_RUN_CAM"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo5 { + regulator-name = "+1.2V_RUN_CAM_FRONT"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vddio_sdmmc3: ldo6 { + regulator-name = "+VDDIO_SDMMC3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7 { + regulator-name = "+1.05V_RUN_CAM_REAR"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo9 { + regulator-name = "+3.3V_RUN_TOUCH"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo10 { + regulator-name = "+2.8V_RUN_CAM_AF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo11 { + regulator-name = "+1.8V_RUN_VPP_FUSE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; }; };
arch/arm/boot/dts/tegra124-jetson-tk1.dts line 1614
Quoted 4 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts +1
-0@@ -1462,6 +1611,7 @@ cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>;
I don't have schematics for this board, but I suspect you mean vqmmc-supply here, per the discussion in the Venice2 VQMMC thread.
Quoted 104 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts +80
-1}; /* eMMC */@@ -1525,6 +1675,72 @@ #address-cells = <1>; #size-cells = <0>; + vdd_mux: regulator at 0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "+VDD_MUX"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_5v0_sys: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "+5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_sys: regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "+3.3V_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_run: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "+3.3V_RUN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + }; + + vdd_3v3_hdmi: regulator at 4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_usb1_vbus: regulator at 7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "+USB0_VBUS_SW"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + vdd_usb3_vbus: regulator at 8 { compatible = "regulator-fixed"; reg = <8>;@@ -1534,6 +1750,20 @@ gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; enable-active-high; gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_3v3_lp0: regulator at 10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "+3.3V_LP0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; }; }; --1.8.1.5
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH 1/1 ARM: tegra: define Jetson TK1 regulators
Quoted 9 lines · Andrew Bresticker
Quoted 9 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts +6
-0+ ldo11 { + regulator-name = "+1.8V_RUN_VPP_FUSE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; }; };
Quoted 9 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts line 1614
Quoted 5 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts +1
-0@@ -1462,6 +1611,7 @@ cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>;I don't have schematics for this board, but I suspect you mean vqmmc-supply here, per the discussion in the Venice2 VQMMC thread.
Schematics can be found at https://developer.nvidia.com/jetson-tk1-support
Cheers,
Peter.
PATCH 1/1 ARM: tegra: define Jetson TK1 regulators
In reply to Andrew BrestickerQuoted 19 lines · Andrew Bresticker
Quoted 17 lines · Stephen Warren
These are mostly identical to the Venice2 regulator definitions, since the board designs are very similar. Differences are:
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This change should likely be propagated to Venice2 for completeness, although it will have no practical effect there since various other regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason is because it's used to driver the UART level-shifter; without this, I see a brief period of UART corruption during cold boots.I suspect this change needs to be propagated to Venice2, and we simply haven't noticed the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.arch/arm/boot/dts/tegra124-jetson-tk1.dts +0
-0
Quoted 8 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts line 1614
Quoted 5 lines
arch/arm/boot/dts/tegra124-jetson-tk1.dts +1
-0@@ -1462,6 +1611,7 @@ cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>;I don't have schematics for this board, but I suspect you mean vqmmc-supply here, per the discussion in the Venice2 VQMMC thread.
This portion of the schematics is essentially identical to Venice2, and you're correct; this should be vqmmc not vmmc. I'll send a patch.