Skip to contentSkip to conversation

Getting USB devices to work on BeagleBoard xM

DISCUSSION Jeremy Cole-Baker 3 participants 5 messages Apr 15, 2014 – Apr 22, 2014

lore
Share & tools
lore
#0 lore raw

Hi,

I've managed to build a couple of different recipes for my BeagleBoard (BeagleBoard xM Rev C), and also had a go at customising it. I think I've tried core-image-minimal and core-image-basic.

The build works OK, and I can set up my micro SD card and get it to boot. I see lots of messages about loading drivers during boot, and I can log in to linux.

However, the USB devices don't seem to be working. The built in USB-Ethernet isn't there, and when I plug in a USB stick nothing happens - nothing in /dev/ and no messages in the system log.

I don't know whether this is something I missed in the build, or some configuration I need to do. I also don't know whether it is specific to the Beagle or a general problem. Unfortunately I am new to Kernel builds and device drivers.

Here's what I've looked into:

The boot-up messages indicate that the USB drivers are loaded, e.g.:

<snip>
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
...
usbcore: registered new interface driver smsc75xx
usbcore: registered new interface driver smsc95xx
...etc

(I think smsc95xx is the USB-Ethernet chip on the beagle board xM).

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap: OMAP-EHCI Host Controller driver
ehci-omap 48064800.ehci: EHCI Host Controller
ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1 ehci-omap 48064800.ehci: irq 93, io mem 0x48064800 ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usbcore: registered new interface driver usb-storage musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -6
mousedev: PS/2 mouse device common for all mice
...Etc

There's a modprobe error which occurs a couple of times:

udevd[71]: starting version 175
modprobe: chdir(3.10.11-yocto-standard): No such file or directory

I also saw errors from the ethernet subsystem (?), along the lines of "eth0: device not found" and "usb0: device not found". This occurred during boot and also when I used "ifup eth0". I'm actually seeing a different error now: "ifconfig: SIOCGIFFLAGS: No such device". In either case, I think it's because something to do with the actual USB hardware is missing or not configured.

"lsmod" shows no modules loaded, i.e.:

root@beagleboard:~#lsmod
Module Size Used by
root@beagleboard:~#

Does this mean that the various device drivers, etc, above are built in to the kernel?

Any suggestions for how to diagnose / fix this problem? Anybody else have experience with the BeagleBoard xM? I'm a bit lost.

Thanks!

Signature · 4 lines
Riverhead Technology
Jeremy Cole-Baker
Ph. (+64) 27 673 0129
www.rhtech.co.nz
#1 lore raw

No USB devices on BeagleBoard xM!

Hi, I still can't figure out how to get the USB hardware working on my BeagelBoard xM.

I've managed to build a couple of different recipes for my BeagleBoard (BeagleBoard xM Rev C), and also had a go at customising it. I think I've tried core-image-minimal and core-image-basic.

The build works OK, and I can set up my micro SD card and get it to boot. I see lots of messages about loading drivers during boot, and I can log in to linux.

However, the USB devices don't seem to be working. The built in USB-Ethernet isn't there, and when I plug in a USB stick nothing happens - nothing in /dev/ and no messages in the system log.

I don't know whether this is something I missed in the build, or some configuration I need to do. I also don't know whether it is specific to the Beagle or a general problem. Unfortunately I am new to Kernel builds and device drivers.

Here's what I've looked into:

The boot-up messages indicate that the USB drivers are loaded, e.g.:

<snip>
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
...
usbcore: registered new interface driver smsc75xx
usbcore: registered new interface driver smsc95xx
...etc

(I think smsc95xx is the USB-Ethernet chip on the beagle board xM).

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap: OMAP-EHCI Host Controller driver
ehci-omap 48064800.ehci: EHCI Host Controller
ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1 ehci-omap 48064800.ehci: irq 93, io mem 0x48064800 ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usbcore: registered new interface driver usb-storage musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -6
mousedev: PS/2 mouse device common for all mice
...Etc

There's a modprobe error which occurs a couple of times:

udevd[71]: starting version 175
modprobe: chdir(3.10.11-yocto-standard): No such file or directory

I also saw errors from the ethernet subsystem (?), along the lines of "eth0: device not found" and "usb0: device not found". This occurred during boot and also when I used "ifup eth0". I'm actually seeing a different error now: "ifconfig: SIOCGIFFLAGS: No such device". In either case, I think it's because something to do with the actual USB hardware is missing or not configured.

"lsmod" shows no modules loaded, i.e.:

root@beagleboard:~# lsmod
Module Size Used by
root@beagleboard:~#

Does this mean that the various device drivers, etc, above are built in to the kernel?

Any suggestions for how to diagnose / fix this problem? Anybody else have experience with the BeagleBoard xM? I'm a bit lost.

Thanks!

Jeremy Cole-Baker

#2 lore raw

Re: No USB devices on BeagleBoard xM!

Quoted 49 lines · Jeremy Cole-Baker

Hi, I still can't figure out how to get the USB hardware working on my BeagelBoard xM.

I've managed to build a couple of different recipes for my BeagleBoard (BeagleBoard xM Rev C), and also had a go at customising it. I think I've tried core-image-minimal and core-image-basic.

The build works OK, and I can set up my micro SD card and get it to boot. I see lots of messages about loading drivers during boot, and I can log in to linux.

However, the USB devices don't seem to be working. The built in USB-Ethernet isn't there, and when I plug in a USB stick nothing happens - nothing in /dev/ and no messages in the system log.

I don't know whether this is something I missed in the build, or some configuration I need to do. I also don't know whether it is specific to the Beagle or a general problem. Unfortunately I am new to Kernel builds and device drivers.

Here's what I've looked into:

The boot-up messages indicate that the USB drivers are loaded, e.g.:

<snip>
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
...
usbcore: registered new interface driver smsc75xx
usbcore: registered new interface driver smsc95xx
...etc

(I think smsc95xx is the USB-Ethernet chip on the beagle board xM).

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap: OMAP-EHCI Host Controller driver
ehci-omap 48064800.ehci: EHCI Host Controller
ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1 ehci-omap 48064800.ehci: irq 93, io mem 0x48064800 ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usbcore: registered new interface driver usb-storage musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -6
mousedev: PS/2 mouse device common for all mice
...Etc

Quoted 4 lines

There's a modprobe error which occurs a couple of times:

udevd[71]: starting version 175
modprobe: chdir(3.10.11-yocto-standard): No such file or directory

Doesn't seem like you have modules installed in your rootfs ^^^

If you build core-image-minimal, you then need to extract the modules from a tarball you got in the deplot area...

Quoted 28 lines

I also saw errors from the ethernet subsystem (?), along the lines of "eth0: device not found" and "usb0: device not found". This occurred during boot and also when I used "ifup eth0". I'm actually seeing a different error now: "ifconfig: SIOCGIFFLAGS: No such device". In either case, I think it's because something to do with the actual USB hardware is missing or not configured.

"lsmod" shows no modules loaded, i.e.:

root@beagleboard:~# lsmod
Module Size Used by
root@beagleboard:~#

Does this mean that the various device drivers, etc, above are built in to the kernel?

Any suggestions for how to diagnose / fix this problem? Anybody else have experience with the BeagleBoard xM? I'm a bit lost.

Thanks!

Jeremy Cole-Baker

Signature · 4 lines
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
#3 lore raw

Re: No USB devices on BeagleBoard xM!

Hi, thanks for your reply.

I did have a modules file from the build, which I installed on my root fs as follows:

tar x -C _root/ -f modules–3.10.11+git0+363bd856c8_702040ac7c-r0-beagleboard-20140415194907.tgz

(_root is a link to the correct partition on the flash card). The file contained a number of directories and files which were installed under /lib/modules/3.10.11-yocto-standard/. I have verified that these were copied correctly.

Could I be missing one or more modules, because I haven't selected some option in the build somewhere?

Is there any way to find out what module it is trying to load (i.e. when it says "no such file or directory")?

Quoted 90 lines · Denys Dmytriyenko
Quoted 49 lines · Jeremy Cole-Baker

Hi, I still can't figure out how to get the USB hardware working on my BeagelBoard xM.

I've managed to build a couple of different recipes for my BeagleBoard (BeagleBoard xM Rev C), and also had a go at customising it. I think I've tried core-image-minimal and core-image-basic.

The build works OK, and I can set up my micro SD card and get it to boot. I see lots of messages about loading drivers during boot, and I can log in to linux.

However, the USB devices don't seem to be working. The built in USB-Ethernet isn't there, and when I plug in a USB stick nothing happens - nothing in /dev/ and no messages in the system log.

I don't know whether this is something I missed in the build, or some configuration I need to do. I also don't know whether it is specific to the Beagle or a general problem. Unfortunately I am new to Kernel builds and device drivers.

Here's what I've looked into:

The boot-up messages indicate that the USB drivers are loaded, e.g.:

<snip>
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
...
usbcore: registered new interface driver smsc75xx
usbcore: registered new interface driver smsc95xx
...etc

(I think smsc95xx is the USB-Ethernet chip on the beagle board xM).

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap: OMAP-EHCI Host Controller driver
ehci-omap 48064800.ehci: EHCI Host Controller
ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1 ehci-omap 48064800.ehci: irq 93, io mem 0x48064800 ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usbcore: registered new interface driver usb-storage musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -6
mousedev: PS/2 mouse device common for all mice
...Etc

Quoted 4 lines

There's a modprobe error which occurs a couple of times:

udevd[71]: starting version 175
modprobe: chdir(3.10.11-yocto-standard): No such file or directory

Doesn't seem like you have modules installed in your rootfs ^^^

If you build core-image-minimal, you then need to extract the modules from a tarball you got in the deplot area...

Quoted 28 lines

I also saw errors from the ethernet subsystem (?), along the lines of "eth0: device not found" and "usb0: device not found". This occurred during boot and also when I used "ifup eth0". I'm actually seeing a different error now: "ifconfig: SIOCGIFFLAGS: No such device". In either case, I think it's because something to do with the actual USB hardware is missing or not configured.

"lsmod" shows no modules loaded, i.e.:

root@beagleboard:~# lsmod
Module Size Used by
root@beagleboard:~#

Does this mean that the various device drivers, etc, above are built in to the kernel?

Any suggestions for how to diagnose / fix this problem? Anybody else have experience with the BeagleBoard xM? I'm a bit lost.

Thanks!

Jeremy Cole-Baker

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Signature · 1 line
Jeremy Cole-Baker