ARM: dts: r8a7791-koelsch: Add DVFS parameters into cpu0 node for r8a7791
Subsystems (2)
PATCH 5/7 ARM: dts: r8a7791-koelsch: Add DVFS parameters into cpu0 node for r8a7791
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP table. Due to the lack of proper OPP definition, use an arbitrary safe value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this value since the clock transition latency is not the only parameter that will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage since DVS is not supported in R-CAR Gen2.
- clocks
phandle to the CPU clock source. This clock source is used for all the 2 CortexA15 located inside the same cluster.
--- arch/arm/boot/dts/r8a7791.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/boot/dts/r8a7791.dtsi +11 -0
@@ -45,6 +45,17 @@ compatible = "arm,cortex-a15"; reg = <0>; clock-frequency = <1500000000>; + voltage-tolerance = <1>; /* 1% */ + clocks = <&cpg_clocks R8A7791_CLK_Z>; + clock-latency = <300000>; /* 300 us */ + + /* kHz - uV - OPPs unknown yet */ + operating-points = <1500000 1000000>, + <1312500 1000000>, + <1125000 1000000>, + < 937500 1000000>, + < 750000 1000000>, + < 375000 1000000>; }; cpu1: cpu@1 {
Signature · 1 line
1.7.9.5
Quoted 19 lines · Gaku Inami
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP table. Due to the lack of proper OPP definition, use an arbitrary safe value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this value since the clock transition latency is not the only parameter that will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage since DVS is not supported in R-CAR Gen2.
- clocks
phandle to the CPU clock source. This clock source is used for all the 2 CortexA15 located inside the same cluster.
Quoted 4 lines
Signed-off-by Gaku Inami <[email protected]>--- arch/arm/boot/dts/r8a7791.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
You're not touching the Koelsch code in this patch, why mention the board
name in the subject?
WBR, Sergei
Hi Sergei
Thank you for your comment.
Quoted 7 lines
Quoted 4 lines
Signed-off-by Gaku Inami <[email protected]>--- arch/arm/boot/dts/r8a7791.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)You're not touching the Koelsch code in this patch, why mention the board
name in the subject?
The description of subject was not appropriate.
I will fix it.