I need some help with BATMAN configuration
Hi everyone,
My name is Lucy Coya, I´m a telecommunications engineer and I need some help with my BATMAN configuration. I´m using batman-adv-2014-2.0 and batctl-2014-2.0 I´m trying to use BATMAN protocol in a very very simple routing scenario at first to study the protocol. I have:
-Two Laptops using two wireless interfaces each (wlan0 in AP mode and wlan1 in Ad Hoc mode).
I meshed the two wireless interfaces in ad hoc mode according to the wiki steps and it worked fine,so I can ping the interfaces. Now I´m trying to make that two clients connected to the AP interfaces can ping each other through the mesh network. I tried creating a bridge between wlan0 and wlan1 as the wiki says but no ping :-(. I don´t know what to do so any help would be awesome!!! Thanks Sorry if my English is bad :-)
Lucy
50 Aniversario de la Cujae. Inaugurada por Fidel el 2 de diciembre de 1964 http://cujae.edu.cu
I am in a similar boat. I can ping the local interfaces but not the
remote ones.
Please CC me on your email with Lucy.
‹David.
Quoted 25 lines · ext Lucy Coya
Hi everyone,
My name is Lucy Coya, I´m a telecommunications engineer and I need some help with my BATMAN configuration. I´m using batman-adv-2014-2.0 and batctl-2014-2.0
I´m trying to use BATMAN protocol in a very very simple routing scenario at first to study the protocol. I have:
-Two Laptops using two wireless interfaces each (wlan0 in AP mode and wlan1 in Ad Hoc mode).I meshed the two wireless interfaces in ad hoc mode according to the wiki steps and it worked fine,so I can ping the interfaces. Now I´m trying to make that two clients connected to the AP interfaces can ping each other through the mesh network. I tried creating a bridge between wlan0 and wlan1 as the wiki says but no ping :-(. I don´t know what to do so any help would be awesome!!! Thanks
Sorry if my English is bad :-)Lucy
50 Aniversario de la Cujae. Inaugurada por Fidel el 2 de diciembre de 1964 http://cujae.edu.cu
Quoted 9 lines · Lucy Coya
Hi everyone,
My name is Lucy Coya, I´m a telecommunications engineer and I need some help with my BATMAN configuration. I´m using batman-adv-2014-2.0 and batctl-2014-2.0
I´m trying to use BATMAN protocol in a very very simple routing scenario at first to study the protocol. I have:
-Two Laptops using two wireless interfaces each (wlan0 in AP mode and wlan1 in Ad Hoc mode).
Quoted 5 lines
I meshed the two wireless interfaces in ad hoc mode according to the wiki steps and it worked fine,so I can ping the interfaces. Now I´m trying to make that two clients connected to the AP interfaces can ping each other through the mesh network. I tried creating a bridge between wlan0 and wlan1 as the wiki says but no ping :-(. I don´t know what to
you should bridge wlan0 (the AP interface) with bat0 and add wlan1 (adhoc) to bat0 with "batctl if add"
in ascii art that'd be:
br-lan
\ wlan0
\ bat0
\ wlan1
in bash commands that'd be
# add adhoc interface to bat0 batctl if add wlan1
# remove addresses from slave interfaces ip addr flush dev wlan0 ip addr flush dev wlan1 ip addr flush dev bat0
# bridge ap interface with bat0 brctl addif br-lan wlan0 brctl addif br-lan bat0
# add the ip address to the bridge ip addr add dev br-lan 2001:db8::1/64
cheers!
gui
Quoted 11 lines
do so any help would be awesome!!! Thanks
Sorry if my English is bad :-)Lucy
50 Aniversario de la Cujae. Inaugurada por Fidel el 2 de diciembre de 1964 http://cujae.edu.cu