Skip to contentSkip to conversation

No network at startup using core-image-minimal

DISCUSSION Dr. Markus Eich 2 participants 5 messages Aug 8, 2014 – Aug 12, 2014

lore
Share & tools
lore
#0 lore raw

Dear all,

I am setting up my Odroid XU with yocto using the core-image-minimal receipe. Almost done and I am able to boot the system and log in via screen (UART), but..

The network is not present at start-up. When I do lsmod I just see "Not tainted" and no modules are loaded.

The module I need to load is the smsc95xx module. When I tried to load the driver with "modpobe" it could not find the driver (although it is in /lib/modules/3.4.98-custom/kernel/drivers/net/usb) I had to manually add it to /lib/modules/3.4.98-custom/modules.dep (which was empty after the bitbake process in rootfs)

So I added "kernel/drivers/net/usb/smsc95xx.ko: " to modules.dep.

Then I could load it with modprobe. In order to load it at startup

I created a /etc/modules with the content "smsc95xx". Now my question:

Is there an easier (bitbake) way to make the modules load at startup without editing configs on the target device? Am I missing something? Does core-image-minimal not include network?

Cheers,

Markus

Signature · 35 lines
Dr.-Ing. Markus Eich

 Senior Researcher
 Marine Inspection Robotics
 Space Robotics
 
 Besuchsadresse der Nebengeschäftstelle:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 5
 28359 Bremen, Germany
 
 Postadresse der Hauptgeschäftsstelle Standort Bremen:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 1
 28359 Bremen, Germany

 Tel.:     +49 421 178 45-4105
 Zentrale: +49 421 178 45-0
 Fax:      +49 421 178 45-4150 (Faxe bitte namentlich kennzeichnen)
 E-Mail:   [email protected]

 Weitere Informationen: http://www.dfki.de/robotik
 -----------------------------------------------------------------------
 Deutsches Forschungszentrum fuer Kuenstliche Intelligenz GmbH
 Firmensitz: Trippstadter Straße 122, D-67663 Kaiserslautern
 Geschaeftsfuehrung: Prof. Dr. Dr. h.c. mult. Wolfgang Wahlster
 (Vorsitzender) Dr. Walter Olthoff
 Vorsitzender des Aufsichtsrats: Prof. Dr. h.c. Hans A. Aukes
 Amtsgericht Kaiserslautern, HRB 2313
 Sitz der Gesellschaft: Kaiserslautern (HRB 2313)
 USt-Id.Nr.:    DE 148646973
 Steuernummer:  19/673/0060/3
 -----------------------------------------------------------------------
#1 lore raw

Hi Markus,

Please try core-image-base instead of core-image-minimal. That should provide you with the necessary network support.

Best regards,
Rudi

Quoted 74 lines · Dr. Markus Eich

Dear all,

I am setting up my Odroid XU with yocto using the core-image-minimal receipe. Almost done and I am able to boot the system and log in via screen (UART), but..

The network is not present at start-up. When I do lsmod I just see "Not tainted" and no modules are loaded.

The module I need to load is the smsc95xx module. When I tried to load the driver with "modpobe" it could not find the driver (although it is in /lib/modules/3.4.98-custom/kernel/drivers/net/usb)
I had to manually add it to /lib/modules/3.4.98-custom/modules.dep (which was empty after the bitbake process in rootfs)

So I added "kernel/drivers/net/usb/smsc95xx.ko: " to modules.dep.

Then I could load it with modprobe. In order to load it at startup

I created a /etc/modules with the content "smsc95xx". Now my question:

Is there an easier (bitbake) way to make the modules load at startup without editing configs on the target device? Am I missing something? Does core-image-minimal not include network?

Cheers,

Markus

--
Dr.-Ing. Markus Eich

Senior Researcher
Marine Inspection Robotics
Space Robotics
Besuchsadresse der Nebengeschäftstelle:
DFKI GmbH
Robotics Innovation Center Robert-Hooke-Straße 5
28359 Bremen, Germany
Postadresse der Hauptgeschäftsstelle Standort Bremen:
DFKI GmbH
Robotics Innovation Center Robert-Hooke-Straße 1
28359 Bremen, Germany

Tel.: +49 421 178 45-4105
Zentrale: +49 421 178 45-0
Fax: +49 421 178 45-4150 (Faxe bitte namentlich kennzeichnen)
E-Mail: [email protected]

Weitere Informationen: http://www.dfki.de/robotik
-----------------------------------------------------------------------
Deutsches Forschungszentrum fuer Kuenstliche Intelligenz GmbH
Firmensitz: Trippstadter Straße 122, D-67663 Kaiserslautern
Geschaeftsfuehrung: Prof. Dr. Dr. h.c. mult. Wolfgang Wahlster (Vorsitzender) Dr. Walter Olthoff
Vorsitzender des Aufsichtsrats: Prof. Dr. h.c. Hans A. Aukes Amtsgericht Kaiserslautern, HRB 2313
Sitz der Gesellschaft: Kaiserslautern (HRB 2313)
USt-Id.Nr.: DE 148646973
Steuernummer: 19/673/0060/3
-----------------------------------------------------------------------

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

#2 lore raw

Hi Rudolf,

same result with the core-image-base.

It seems that depmod is not run before building the image/modules in the deploy folder. I have a custom kernel recipes. How can I make bitbake to run depmod -a on the rootfs?

My recipes inherits kernel

and requires

recipes-kernel/linux/linux-yocto.inc

Cheers,

Markus

Quoted 85 lines · Rudolf Streif

Hi Markus,

Please try core-image-base instead of core-image-minimal. That should provide you with the necessary network support.

Best regards,
Rudi

On Aug 8, 2014 6:46 AM, "Dr. Markus Eich" <[email protected] <mailto:[email protected]>> wrote:

Dear all,

I am setting up my Odroid XU with yocto using the core-image-minimal receipe. Almost done and I am able to boot the system and log in via screen (UART), but..

The network is not present at start-up. When I do lsmod I just see "Not tainted" and no modules are loaded.

The module I need to load is the smsc95xx module. When I tried to load the driver with "modpobe" it could not find the driver (although it is in /lib/modules/3.4.98-custom/kernel/drivers/net/usb) I had to manually add it to /lib/modules/3.4.98-custom/modules.dep (which was empty after the bitbake process in rootfs)

So I added "kernel/drivers/net/usb/smsc95xx.ko: " to modules.dep.

Then I could load it with modprobe. In order to load it at startup

I created a /etc/modules with the content "smsc95xx". Now my question:

Is there an easier (bitbake) way to make the modules load at startup without editing configs on the target device? Am I missing something? Does core-image-minimal not include network?

Cheers,

Markus

--
Dr.-Ing. Markus Eich

Senior Researcher
Marine Inspection Robotics
Space Robotics
Besuchsadresse der Nebengeschäftstelle:
DFKI GmbH
Robotics Innovation Center Robert-Hooke-Straße 5
28359 Bremen, Germany
Postadresse der Hauptgeschäftsstelle Standort Bremen:
DFKI GmbH
Robotics Innovation Center Robert-Hooke-Straße 1
28359 Bremen, Germany

Tel.: +49 421 178 45-4105 <tel:%2B49%20421%20178%2045-4105>
Zentrale: +49 421 178 45-0 <tel:%2B49%20421%20178%2045-0>
Fax: +49 421 178 45-4150 <tel:%2B49%20421%20178%2045-4150> (Faxe
bitte namentlich kennzeichnen)
E-Mail: [email protected] <mailto:[email protected]>

Weitere Informationen: http://www.dfki.de/robotik
-----------------------------------------------------------------------
Deutsches Forschungszentrum fuer Kuenstliche Intelligenz GmbH
Firmensitz: Trippstadter Straße 122, D-67663 Kaiserslautern
Geschaeftsfuehrung: Prof. Dr. Dr. h.c. mult. Wolfgang Wahlster (Vorsitzender) Dr. Walter Olthoff
Vorsitzender des Aufsichtsrats: Prof. Dr. h.c. Hans A. Aukes Amtsgericht Kaiserslautern, HRB 2313
Sitz der Gesellschaft: Kaiserslautern (HRB 2313)
USt-Id.Nr.: DE 148646973
Steuernummer: 19/673/0060/3
-----------------------------------------------------------------------

--
_______________________________________________
yocto mailing list
[email protected] <mailto:[email protected]>
https://lists.yoctoproject.org/listinfo/yocto

Signature · 35 lines
Dr.-Ing. Markus Eich

 Senior Researcher
 Marine Inspection Robotics
 Space Robotics
 
 Besuchsadresse der Nebengeschäftstelle:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 5
 28359 Bremen, Germany
 
 Postadresse der Hauptgeschäftsstelle Standort Bremen:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 1
 28359 Bremen, Germany

 Tel.:     +49 421 178 45-4105
 Zentrale: +49 421 178 45-0
 Fax:      +49 421 178 45-4150 (Faxe bitte namentlich kennzeichnen)
 E-Mail:   [email protected]

 Weitere Informationen: http://www.dfki.de/robotik
 -----------------------------------------------------------------------
 Deutsches Forschungszentrum fuer Kuenstliche Intelligenz GmbH
 Firmensitz: Trippstadter Straße 122, D-67663 Kaiserslautern
 Geschaeftsfuehrung: Prof. Dr. Dr. h.c. mult. Wolfgang Wahlster
 (Vorsitzender) Dr. Walter Olthoff
 Vorsitzender des Aufsichtsrats: Prof. Dr. h.c. Hans A. Aukes
 Amtsgericht Kaiserslautern, HRB 2313
 Sitz der Gesellschaft: Kaiserslautern (HRB 2313)
 USt-Id.Nr.:    DE 148646973
 Steuernummer:  19/673/0060/3
 -----------------------------------------------------------------------
#3 lore raw

Hi Markus,

Quoted 6 lines

same result with the core-image-base.

It seems that depmod is not run before building the image/modules in the deploy folder. I have a custom kernel recipes. How can I make bitbake to run depmod -a on the rootfs?

Quoted 7 lines

My recipes inherits kernel

and requires

recipes-kernel/linux/linux-yocto.inc

Ok, in this case you want to use

module_autoload_<modname> = "modname1 modname2 modname3"

in your kernel recipe (or distro or machine configuration which is actually preferable). For example

module_autoload_smsc95xx = "smsc95xx"

The module-split class should pick it up and add the module to /etc/modules-load.d/modname.conf.

Cheers,

Rudi

#4 lore raw

Thank you for the info.

Solved it the following way:

I added

IMAGE_INSTALL += "kernel_modules" to my local.conf.

Now SMSC95xx (plus some other modules, like joydrive) are autoloaded on boot.

Cheers,

Markus

Am 12.08.2014 um 18:56 schrieb Rudolf Streif:

Quoted 23 lines

Hi Markus,

same result with the core-image-base.

It seems that depmod is not run before building the image/modules in the deploy folder. I have a custom kernel recipes. How can I make bitbake to run depmod -a on the rootfs?

My recipes inherits kernel

and requires

recipes-kernel/linux/linux-yocto.inc

Ok, in this case you want to use

module_autoload_<modname> = "modname1 modname2 modname3"
in your kernel recipe (or distro or machine configuration which is actually preferable). For example module_autoload_smsc95xx = "smsc95xx"
The module-split class should pick it up and add the module to /etc/modules-load.d/modname.conf. Cheers,
Rudi

Signature · 35 lines
Dr.-Ing. Markus Eich

 Senior Researcher
 Marine Inspection Robotics
 Space Robotics
  
 Besuchsadresse der Nebengeschäftstelle:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 5
 28359 Bremen, Germany
 
 Postadresse der Hauptgeschäftsstelle Standort Bremen:
 DFKI GmbH
 Robotics Innovation Center
 Robert-Hooke-Straße 1
 28359 Bremen, Germany

 Tel.:     +49 421 178 45-4105
 Zentrale: +49 421 178 45-0
 Fax:      +49 421 178 45-4150 (Faxe bitte namentlich kennzeichnen)
 E-Mail:   [email protected]

 Weitere Informationen: http://www.dfki.de/robotik
 -----------------------------------------------------------------------
 Deutsches Forschungszentrum fuer Kuenstliche Intelligenz GmbH
 Firmensitz: Trippstadter Straße 122, D-67663 Kaiserslautern
 Geschaeftsfuehrung: Prof. Dr. Dr. h.c. mult. Wolfgang Wahlster
 (Vorsitzender) Dr. Walter Olthoff
 Vorsitzender des Aufsichtsrats: Prof. Dr. h.c. Hans A. Aukes
 Amtsgericht Kaiserslautern, HRB 2313
 Sitz der Gesellschaft: Kaiserslautern (HRB 2313)
 USt-Id.Nr.:    DE 148646973
 Steuernummer:  19/673/0060/3
 -----------------------------------------------------------------------