Skip to contentSkip to conversation

ASoC: CPU DAI samsung-i2s.0 not registered

DISCUSSION Matt Flax 3 participants 7 messages Aug 14, 2014

lore
Share & tools
lore

Matt Flax

author
#0 lore raw

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

    i2s0: i2s@03830000 {
        compatible = "samsung,i2s-v5";
        reg = <0x03830000 0x100>;
        dmas = <&pdma0 10
            &pdma0 9
            &pdma0 8>;
        dma-names = "tx", "rx", "tx-sec";
        clocks = <&clock_audss EXYNOS_I2S_BUS>,
            <&clock_audss EXYNOS_I2S_BUS>,
            <&clock_audss EXYNOS_SCLK_I2S>;
        clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
        samsung,supports-6ch;
        samsung,supports-rstclr;
        samsung,supports-secdai;
        samsung,idma-addr = <0x03000000>;
        pinctrl-names = "default";
        pinctrl-0 = <&i2s0_bus>;
    };

    implant: implant@0 {
            compatible = "bva,implant";
    };

    sound {
        compatible = "bva,implant-bva";

        samsung,i2s-controller = <&i2s0>;
        samsung,audio-codec = <&implant>;
    };
#1 lore raw

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 40 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

     i2s0: i2s@03830000 {
         compatible = "samsung,i2s-v5";
         reg = <0x03830000 0x100>;
         dmas = <&pdma0 10
             &pdma0 9
             &pdma0 8>;
         dma-names = "tx", "rx", "tx-sec";
         clocks = <&clock_audss EXYNOS_I2S_BUS>,
             <&clock_audss EXYNOS_I2S_BUS>,
             <&clock_audss EXYNOS_SCLK_I2S>;
         clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
         samsung,supports-6ch;
         samsung,supports-rstclr;
         samsung,supports-secdai;
         samsung,idma-addr = <0x03000000>;
         pinctrl-names = "default";
         pinctrl-0 = <&i2s0_bus>;
     };

     implant: implant@0 {
             compatible = "bva,implant";
     };

     sound {
         compatible = "bva,implant-bva";

         samsung,i2s-controller = <&i2s0>;
         samsung,audio-codec = <&implant>;
     };

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#2 lore raw

Thanks for the idea ... I have set this :

    i2s0: i2s@03830000 {
        status = "okay";
    };

and I get the same problem.

Is there anything else which is required to register the samsun-i2s.0 driver ? Can you tell me whether my codec/driver requires any code to register the i2s0 ?

I have the following in my driver :
static struct snd_soc_dai_link implant_dai = {
.name = "implant bva",
.stream_name = "IMPLANT",
.cpu_dai_name = "samsung-i2s.0",
.codec_dai_name = "implant-pcm",
.platform_name = "samsung-i2s.0",
.codec_name = "implant-codec",
};

thanks
Matt

Quoted 56 lines · Inha Song

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 36 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

      i2s0: i2s@03830000 {
          compatible = "samsung,i2s-v5";
          reg = <0x03830000 0x100>;
          dmas = <&pdma0 10
              &pdma0 9
              &pdma0 8>;
          dma-names = "tx", "rx", "tx-sec";
          clocks = <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_SCLK_I2S>;
          clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
          samsung,supports-6ch;
          samsung,supports-rstclr;
          samsung,supports-secdai;
          samsung,idma-addr = <0x03000000>;
          pinctrl-names = "default";
          pinctrl-0 = <&i2s0_bus>;
      };

      implant: implant@0 {
              compatible = "bva,implant";
      };

      sound {
          compatible = "bva,implant-bva";

          samsung,i2s-controller = <&i2s0>;
          samsung,audio-codec = <&implant>;
      };
Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#3 lore raw

Hi

Il 14/ago/2014 06:12 "Matt Flax" <[email protected]> ha scritto:

Quoted 9 lines

Thanks for the idea ... I have set this :

    i2s0: i2s@03830000 {
        status = "okay";
    };

and I get the same problem.

Is there anything else which is required to register the samsun-i2s.0

driver ?

Quoted 1 line

Can you tell me whether my codec/driver requires any code to register the

i2s0 ?

Quoted 11 lines

I have the following in my driver :
static struct snd_soc_dai_link implant_dai = {
.name = "implant bva",
.stream_name = "IMPLANT",
.cpu_dai_name = "samsung-i2s.0",
.codec_dai_name = "implant-pcm",
.platform_name = "samsung-i2s.0",
.codec_name = "implant-codec",
};

Quoted 3 lines

thanks
Matt

What version of the kernel are you using?

Michael

Quoted 66 lines · Inha Song
Quoted 54 lines

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 36 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

      i2s0: i2s@03830000 {
          compatible = "samsung,i2s-v5";
          reg = <0x03830000 0x100>;
          dmas = <&pdma0 10
              &pdma0 9
              &pdma0 8>;
          dma-names = "tx", "rx", "tx-sec";
          clocks = <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_SCLK_I2S>;
          clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
          samsung,supports-6ch;
          samsung,supports-rstclr;
          samsung,supports-secdai;
          samsung,idma-addr = <0x03000000>;
          pinctrl-names = "default";
          pinctrl-0 = <&i2s0_bus>;
      };

      implant: implant@0 {
              compatible = "bva,implant";
      };

      sound {
          compatible = "bva,implant-bva";

          samsung,i2s-controller = <&i2s0>;
          samsung,audio-codec = <&implant>;
      };
Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#4 lore raw

Hi Michael,

I managed to get it to load the driver now with this strange device tree related hack I found in the smdk_wm8994 driver ...
http://mailman.alsa-project.org/pipermail/alsa-devel/2014-August/080030.html

But I got a new riddle there as well ... not sure how to register my codec now ...

My kernel version is :
Linux version 3.14.0 (flatmax@highAcuity) (gcc version 4.8.2 (GCC) ) #1 SMP PREEMPT Thu Aug 14 15:47:07 EST 2014

Quoted 99 lines · Michael Trimarchi

Hi

Il 14/ago/2014 06:12 "Matt Flax" <[email protected]> ha scritto:

Quoted 8 lines

Thanks for the idea ... I have set this :

     i2s0: i2s@03830000 {
         status = "okay";
     };

and I get the same problem.

Is there anything else which is required to register the samsun-i2s.0

driver ?

Quoted 1 line

Can you tell me whether my codec/driver requires any code to register the

i2s0 ?

Quoted 10 lines

I have the following in my driver :
static struct snd_soc_dai_link implant_dai = {
.name = "implant bva",
.stream_name = "IMPLANT",
.cpu_dai_name = "samsung-i2s.0",
.codec_dai_name = "implant-pcm",
.platform_name = "samsung-i2s.0",
.codec_name = "implant-codec",
};

Quoted 3 lines

thanks
Matt

What version of the kernel are you using?

Michael

Quoted 58 lines · Inha Song
Quoted 48 lines

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 36 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

       i2s0: i2s@03830000 {
           compatible = "samsung,i2s-v5";
           reg = <0x03830000 0x100>;
           dmas = <&pdma0 10
               &pdma0 9
               &pdma0 8>;
           dma-names = "tx", "rx", "tx-sec";
           clocks = <&clock_audss EXYNOS_I2S_BUS>,
               <&clock_audss EXYNOS_I2S_BUS>,
               <&clock_audss EXYNOS_SCLK_I2S>;
           clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
           samsung,supports-6ch;
           samsung,supports-rstclr;
           samsung,supports-secdai;
           samsung,idma-addr = <0x03000000>;
           pinctrl-names = "default";
           pinctrl-0 = <&i2s0_bus>;
       };

       implant: implant@0 {
               compatible = "bva,implant";
       };

       sound {
           compatible = "bva,implant-bva";

           samsung,i2s-controller = <&i2s0>;
           samsung,audio-codec = <&implant>;
       };
Quoted 8 lines
Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#5 lore raw
In reply to Matt Flax

I think I have gotten around this problem using the code in the samsung/smdk_wm8994.c probe function :
implant_dai.cpu_dai_name = NULL;
implant_dai.cpu_of_node = of_parse_phandle(np,

"samsung,i2s-controller", 0);
        implant_dai.platform_name = NULL;
        implant_dai.platform_of_node = implant_dai.cpu_of_node;

Now having problems with the codec registration :
.codec_name = "implant-codec",

ASoC: CODEC implant-codec not registered

I am looking for the magic here ...

Any ideas ?

Matt

Quoted 85 lines · Matt Flax

Thanks for the idea ... I have set this :

    i2s0: i2s@03830000 {
        status = "okay";
    };

and I get the same problem.

Is there anything else which is required to register the samsun-i2s.0 driver ? Can you tell me whether my codec/driver requires any code to register the i2s0 ?

I have the following in my driver :
static struct snd_soc_dai_link implant_dai = {
.name = "implant bva",
.stream_name = "IMPLANT",
.cpu_dai_name = "samsung-i2s.0",
.codec_dai_name = "implant-pcm",
.platform_name = "samsung-i2s.0",
.codec_name = "implant-codec",
};

thanks
Matt

Quoted 48 lines · Inha Song

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 36 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

      i2s0: i2s@03830000 {
          compatible = "samsung,i2s-v5";
          reg = <0x03830000 0x100>;
          dmas = <&pdma0 10
              &pdma0 9
              &pdma0 8>;
          dma-names = "tx", "rx", "tx-sec";
          clocks = <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_SCLK_I2S>;
          clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
          samsung,supports-6ch;
          samsung,supports-rstclr;
          samsung,supports-secdai;
          samsung,idma-addr = <0x03000000>;
          pinctrl-names = "default";
          pinctrl-0 = <&i2s0_bus>;
      };

      implant: implant@0 {
              compatible = "bva,implant";
      };

      sound {
          compatible = "bva,implant-bva";

          samsung,i2s-controller = <&i2s0>;
          samsung,audio-codec = <&implant>;
      };
Quoted 8 lines
Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#6 lore raw
Quoted 10 lines · Matt Flax

I think I have gotten around this problem using the code in the samsung/smdk_wm8994.c probe function :
implant_dai.cpu_dai_name = NULL;
implant_dai.cpu_of_node = of_parse_phandle(np,

"samsung,i2s-controller", 0);
        implant_dai.platform_name = NULL;
        implant_dai.platform_of_node = implant_dai.cpu_of_node;

Now having problems with the codec registration :
.codec_name = "implant-codec",

Quoted 7 lines

ASoC: CODEC implant-codec not registered

I am looking for the magic here ...

Any ideas ?

I solved this problem using the following code :
implant_dai.codec_name = NULL; implant_dai.codec_of_node = of_parse_phandle(np,
"samsung,audio-codec", 0);

Quoted 93 lines

Matt

Quoted 81 lines · Matt Flax

Thanks for the idea ... I have set this :

    i2s0: i2s@03830000 {
        status = "okay";
    };

and I get the same problem.

Is there anything else which is required to register the samsun-i2s.0 driver ? Can you tell me whether my codec/driver requires any code to register the i2s0 ?

I have the following in my driver :
static struct snd_soc_dai_link implant_dai = {
.name = "implant bva",
.stream_name = "IMPLANT",
.cpu_dai_name = "samsung-i2s.0",
.codec_dai_name = "implant-pcm",
.platform_name = "samsung-i2s.0",
.codec_name = "implant-codec",
};

thanks
Matt

Quoted 48 lines · Inha Song

Hi,

Did you set to i2s0 status?

-> status = "okay";

Best regards,
Inha Song.

Quoted 36 lines · On Thu, 14 Aug 2014 12:19:26 +1000 Matt Flax <[email protected]> wrote:

Hi there,

Any ideas why this problem is coming up when I try to load a driver ?

Here is the device tree :

      i2s0: i2s@03830000 {
          compatible = "samsung,i2s-v5";
          reg = <0x03830000 0x100>;
          dmas = <&pdma0 10
              &pdma0 9
              &pdma0 8>;
          dma-names = "tx", "rx", "tx-sec";
          clocks = <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_I2S_BUS>,
              <&clock_audss EXYNOS_SCLK_I2S>;
          clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
          samsung,supports-6ch;
          samsung,supports-rstclr;
          samsung,supports-secdai;
          samsung,idma-addr = <0x03000000>;
          pinctrl-names = "default";
          pinctrl-0 = <&i2s0_bus>;
      };

      implant: implant@0 {
              compatible = "bva,implant";
      };

      sound {
          compatible = "bva,implant-bva";

          samsung,i2s-controller = <&i2s0>;
          samsung,audio-codec = <&implant>;
      };
Quoted 8 lines
Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Quoted 4 lines

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel