Skip to contentSkip to conversation

mpc8315e-rdb is probably a poor choice as powerpc example...

DISCUSSION Bob Cochran 3 participants 6 messages Aug 14, 2014

lore
Share & tools
lore
#0 lore raw

As most of you know, the mpc8315e-rdb is the powerpc reference platform in meta-yocto-bsp. This is old technology and not a good representative of QorIQ.

I suggest something from the P or T family be used. The P1010RDB is probably a good choice, but others may prefer an SMP machine.

I'm willing to help to make it happen.

Bob

#1 lore raw
Quoted 3 lines · Bob Cochran

As most of you know, the mpc8315e-rdb is the powerpc reference platform in meta-yocto-bsp. This is old technology and not a good representative of QorIQ.

We've been working with FSL to find a suitable replacement for some time, and the discussions were happening in the sprint, but stalled for the summer months.

Quoted 3 lines

I suggest something from the P or T family be used. The P1010RDB is probably a good choice, but others may prefer an SMP machine.

The choice is equally about the machine and about the ability to purchase the target at a reasonable price. We don't use hard to find, or expensive boards.

So if you do have specific suggestions, and purchase information, send it along and it can be rolled into the ongoing discussions.

Bruce

Quoted 10 lines

I'm willing to help to make it happen.

Bob

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Signature · 2 lines
"Thou shalt not follow the NULL pointer, for chaos and madness await
thee at its end"
#2 lore raw
Quoted 9 lines · Bruce Ashfield
Quoted 3 lines · Bob Cochran

As most of you know, the mpc8315e-rdb is the powerpc reference platform in meta-yocto-bsp. This is old technology and not a good representative of QorIQ.

We've been working with FSL to find a suitable replacement for some time, and the discussions were happening in the sprint, but stalled for the summer months.

Quoted 1 line
Quoted 8 lines
Quoted 2 lines

I suggest something from the P or T family be used. The P1010RDB is probably a good choice, but others may prefer an SMP machine.

The choice is equally about the machine and about the ability to purchase the target at a reasonable price. We don't use hard to find, or expensive boards.

So if you do have specific suggestions, and purchase information, send it along and it can be rolled into the ongoing discussions.

Thank you for the reply Bruce. I suggested the P1010RDB because we have one of these (older rev), and we have found few problems working periodically with Poky & related master branches over the past couple of years. We also test the mainline kernel on it - typically with success.
In other words, it's basically been stable.

It's $545 @ Digikey: http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&keywords=P1010RDB

It's a nice system based on e500v2 with 3 GE ports, SATA, USB, FLASH, and SD card support ( note - it does have a funky address mux / switch on board that limits the use of all peripherals at the same time).

The downside is it's starting to get a little old, so Freescale may prefer to point to a T series QorIQ. I just think it will be important to stay away from a DPAA-based device, due to the complexity and my perception that some of the related code isn't yet in the public domain & may not get there for some time.

And as I stated before, an SMP processor may be a better choice along with showing a hypervisor. It all depends on what's important to Yocto, Freescale, and their customers.

Bob

Quoted 16 lines

Bruce

Quoted 10 lines

I'm willing to help to make it happen.

Bob

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

#3 lore raw
Quoted 24 lines · Bob Cochran
Quoted 14 lines · Bruce Ashfield
Quoted 3 lines · Bob Cochran

As most of you know, the mpc8315e-rdb is the powerpc reference platform in meta-yocto-bsp. This is old technology and not a good representative of QorIQ.

We've been working with FSL to find a suitable replacement for some time, and
the discussions were happening in the sprint, but stalled for the summer months.

Quoted 3 lines

I suggest something from the P or T family be used. The P1010RDB is probably a good choice, but others may prefer an SMP machine.

Quoted 8 lines

The choice is equally about the machine and about the ability to purchase the
target at a reasonable price. We don't use hard to find, or expensive boards.

So if you do have specific suggestions, and purchase information, send it along
and it can be rolled into the ongoing discussions.

Quoted 8 lines

Thank you for the reply Bruce. I suggested the P1010RDB because we have one of these (older rev), and we have found few problems working periodically with Poky & related master branches over the past couple of years. We also test the mainline kernel on it - typically with success.
In other words, it's basically been stable.

It's $545 @ Digikey:
http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&keywords=P1010RDB

ouch. personally, i think that's too pricey for one of the yocto
reference boards. it should be affordable by *hobbyists*, which suggests a price of at most $200, if not less. $545 is simply too expensive.

rday

Signature · 7 lines
========================================================================
Robert P. J. Day                                 Ottawa, Ontario, CANADA
                        http://crashcourse.ca

Twitter:                                       http://twitter.com/rpjday
LinkedIn:                               http://ca.linkedin.com/in/rpjday
========================================================================
#4 lore raw
Quoted 32 lines · Robert P. J. Day
Quoted 30 lines · Bob Cochran
Quoted 14 lines · Bruce Ashfield
Quoted 3 lines · Bob Cochran

As most of you know, the mpc8315e-rdb is the powerpc reference platform in meta-yocto-bsp. This is old technology and not a good representative of QorIQ.

We've been working with FSL to find a suitable replacement for some time, and
the discussions were happening in the sprint, but stalled for the summer months.

Quoted 3 lines

I suggest something from the P or T family be used. The P1010RDB is probably a good choice, but others may prefer an SMP machine.

Quoted 8 lines

The choice is equally about the machine and about the ability to purchase the
target at a reasonable price. We don't use hard to find, or expensive boards.

So if you do have specific suggestions, and purchase information, send it along
and it can be rolled into the ongoing discussions.

Thank you for the reply Bruce. I suggested the P1010RDB because we have one of these (older rev), and we have found few problems working periodically with Poky & related master branches over the past couple of years. We also test the mainline kernel on it - typically with success.
In other words, it's basically been stable.

Quoted 7 lines
Quoted 2 lines

It's $545 @ Digikey:
http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&keywords=P1010RDB

ouch. personally, i think that's too pricey for one of the yocto
reference boards. it should be affordable by *hobbyists*, which suggests a price of at most $200, if not less. $545 is simply too expensive.

Agreed!

However, the currently used mpc8315e-rdb is $515 at Digikey: http://www.digikey.com/product-detail/en/MPC8315E-RDBA/MPC8315E-RDBA-ND/2186258

Basically same price

Quoted 3 lines

rday

#5 lore raw
Quoted 2 lines · Bob Cochran
Quoted 1 line · Robert P. J. Day

On Thu, 14 Aug 2014, Bob Cochran wrote:

... snip ...

Quoted 18 lines
Quoted 9 lines
Quoted 9 lines

Thank you for the reply Bruce. I suggested the P1010RDB because we have one
of these (older rev), and we have found few problems working periodically with
Poky & related master branches over the past couple of years. We also test
the mainline kernel on it - typically with success.
In other words, it's basically been stable.

Quoted 7 lines
Quoted 2 lines

It's $545 @ Digikey:
http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&keywords=P1010RDB

ouch. personally, i think that's too pricey for one of the yocto
reference boards. it should be affordable by *hobbyists*, which suggests a price of at most $200, if not less. $545 is simply too expensive.

Quoted 6 lines

Agreed!

However, the currently used mpc8315e-rdb is $515 at Digikey:
http://www.digikey.com/product-detail/en/MPC8315E-RDBA/MPC8315E-RDBA-ND/2186258

Basically same price

ouch again. i didn't know that as i don't have much interest in PPC
boards. i'm still convinced that every yocto reference board should be "affordable". it need not be fully-featured, it need only represent a proof of concept in the sense of building a simple, bootable image. are there no decent PPC dev kits in that price range? none?

rday

Signature · 7 lines
========================================================================
Robert P. J. Day                                 Ottawa, Ontario, CANADA
                        http://crashcourse.ca

Twitter:                                       http://twitter.com/rpjday
LinkedIn:                               http://ca.linkedin.com/in/rpjday
========================================================================