configs/freescale_imx6dlsabresd: add defconfig for iMX6DL SabreSD

new file mode 100644
index 0000000..4177e16
@@ -0,0 +1,27 @@
+# architecture
+BR2_arm=y
+BR2_cortex_a9=y
+
+# system
+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0"
+
+# kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_GIT=y
+BR2_LINUX_KERNEL_CUSTOM_REPO_URL="git://git.freescale.com/imx/linux-2.6-imx.git"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="rel_imx_3.10.17_1.0.0_ga"
+BR2_LINUX_KERNEL_DEFCONFIG="imx_v7"
+BR2_LINUX_KERNEL_UIMAGE_LOADADDR="0x10008000"
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx6dl-sabresd"
+
+# filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+
+# bootloader
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BOARDNAME="mx6dlsabresd"
+BR2_TARGET_UBOOT_FORMAT_IMX=y
+BR2_TARGET_UBOOT_CUSTOM_GIT=y
+BR2_TARGET_UBOOT_CUSTOM_REPO_URL="git://git.freescale.com/imx/uboot-imx.git"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="rel_imx_3.10.17_1.0.0_ga"

new file mode 100755
index 0000000..f82f7b3
@@ -0,0 +1,95 @@
+#!/bin/sh
+
+set -u
+set -e
+
+PROGNAME=$(basename $0)
+
+usage()
+{
+    echo "Create an SD card that boots on an i.MX6DL SABRESD board."
+    echo "It is supposed to work also for the i.MX6Q SABRESD board, but"
+    echo "it this is not tested."
+    echo
+    echo "Note: all data on the the card will be completely deleted!"
+    echo "Use with care!"
+    echo "Superuser permissions may be required to write to the device."
+    echo
+    echo "Usage: ${PROGNAME} <sd_block_device>"
+    echo "Arguments:"
+    echo "  <sd_block_device>     The device to be written to"
+    echo
+    echo "Example: ${PROGNAME} /dev/mmcblk0"
+    echo
+}
+
+if [ $# -ne 1 ]; then
+    usage
+    exit 1
+fi
+
+if [ $(id -u) -ne 0 ]; then
+    echo "${PROGNAME} must be run as root"
+    exit 1
+fi
+
+DEV=${1}
+
+# The partition name prefix depends on the device name:
+# - /dev/sde -> /dev/sde1
+# - /dev/mmcblk0 -> /dev/mmcblk0p1
+if echo ${DEV}|grep -q mmcblk ; then
+    PART="p"
+else
+    PART=""
+fi
+
+PART1=${DEV}${PART}1
+PART2=${DEV}${PART}2
+
+# Unmount the partitions if mounted
+umount ${PART1} || true
+umount ${PART2} || true
+
+# First, clear the card
+dd if=/dev/zero of=${DEV} bs=1M count=2
+
+sync
+
+# Partition the card.
+# SD layout for i.MX6 boot:
+# - Bootloader at offset 1024
+# - FAT partition starting at 1MB offset, containing uImage and *.dtb
+# - ext2/3 partition formatted as ext2 or ext3, containing the root filesystem.
+sfdisk ${DEV} <<EOF
+32,480,b
+512,,L
+EOF
+
+sync
+
+# Copy the bootloader@offset 1024
+dd if=output/images/u-boot.imx of=${DEV} obs=512 seek=2
+
+# Prepare a temp dir for mounting partitions
+TMPDIR=$(mktemp -d)
+
+# FAT partition: kernel and DTBs
+mkfs.vfat ${PART1}
+mount ${PART1} ${TMPDIR}
+cp output/images/uImage ${TMPDIR}/
+cp output/images/*.dtb  ${TMPDIR}/
+sync
+umount ${TMPDIR}
+
+# ext2 partition: root filesystem
+mkfs.ext2 ${PART2}
+mount ${PART2} ${TMPDIR}
+tar -C ${TMPDIR}/ -xf output/images/rootfs.tar
+sync
+umount ${TMPDIR}
+
+# Cleanup
+rmdir ${TMPDIR}
+sync
+echo Done

67 lines not on this page · raw message