0/7] Remove mach-kirkwood
Subsystems (7)
PATCH v3 1/1 0/7] Remove mach-kirkwood
This is mostly a resend of these patches, removing mach-kirkwood. Not all maintainers picked up there patches, which has resulted in some dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that Jason Cooper will submit them for inclusion in an RC. Subsystem maintainers do not need to do anything.
The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new, since what it is removing was added during v3.16-rcX. It follows the pattern of all the other patches.
Andrew Lunn (7):
cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
ata: Remove ARCH_KIRKWOOD dependency
thermal: Remove ARCH_KIRKWOOD dependency
leds: Remove ARCH_KIRKWOOD dependency
rtc: Remove ARCH_KIRKWOOD dependency
watchdog: Remove ARCH_KIRKWOOD dependency
cpufreq: Remove ARCH_KIRKWOOD dependency
drivers/ata/Kconfig | 2 +- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpuidle/Kconfig.arm | 2 +- drivers/leds/Kconfig | 4 ++-- drivers/rtc/Kconfig | 2 +- drivers/thermal/Kconfig | 2 +- drivers/watchdog/Kconfig | 2 +- 7 files changed, 8 insertions(+), 8 deletions(-)
--
2.1.0
PATCH v3 1/1 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. Use MACH_KIRKWOOD, which is set when kirkwood is built as part of mach-mvebu.
--- drivers/cpuidle/Kconfig.arm | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpuidle/Kconfig.arm +1 -1
@@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE config ARM_KIRKWOOD_CPUIDLE bool "CPU Idle Driver for Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD help This adds the CPU Idle driver for Marvell Kirkwood SoCs.
Signature · 1 line
2.1.0
PATCH v3 1/1 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
Quoted 8 lines · Andrew Lunn
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. Use
MACH_KIRKWOOD, which is set when kirkwood is built as part of mach-mvebu.Signed-off-by Andrew Lunn <[email protected]>Cc Daniel Lezcano <[email protected]>Cc Rafael J. Wysocki <[email protected]>Cc linux-pm at vger.kernel.org
Quoted 18 lines
--- drivers/cpuidle/Kconfig.arm | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/cpuidle/Kconfig.arm +1
-1@@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE config ARM_KIRKWOOD_CPUIDLE bool "CPU Idle Driver for Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD help This adds the CPU Idle driver for Marvell Kirkwood SoCs.
Signature · 5 lines
<http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog
PATCH v3 1/1 2/7] ata: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. ARCH_MVEBU is sufficient.
--- drivers/ata/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ata/Kconfig +1 -1
@@ -299,7 +299,7 @@ config SATA_HIGHBANK config SATA_MV tristate "Marvell SATA support" - depends on PCI || ARCH_DOVE || ARCH_KIRKWOOD || ARCH_MV78XX0 || \ + depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \ ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST select GENERIC_PHY help
Signature · 1 line
2.1.0
PATCH v3 1/1 2/7] ata: Remove ARCH_KIRKWOOD dependency
Quoted 6 lines · Andrew Lunn
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBUis sufficient.Signed-off-by Andrew Lunn <[email protected]>Cc Tejun Heo <[email protected]>Cc linux-ide at vger.kernel.org
Thanks.
Signature · 1 line
tejun
PATCH v3 1/1 3/7] thermal: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as part of ARCH_MVEBU.
--- drivers/thermal/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/thermal/Kconfig +1 -1
@@ -143,7 +143,7 @@ config RCAR_THERMAL config KIRKWOOD_THERMAL tristate "Temperature sensor on Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD depends on OF help Support for the Kirkwood thermal sensor driver into the Linux thermal
Signature · 1 line
2.1.0
PATCH v3 1/1 3/7] thermal: Remove ARCH_KIRKWOOD dependency
Andrew,
Quoted 16 lines · Andrew Lunn
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. Depend on
MACH_KIRKWOOD, which will be set when kirkwood is built as part ofARCH_MVEBU.Signed-off-by Andrew Lunn <[email protected]>Cc Zhang Rui <[email protected]>Cc linux-pm at vger.kernel.org--- drivers/thermal/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/thermal/Kconfig +0
-0
drivers/thermal/Kconfig config RCAR_THERMAL · line 146
Quoted 5 lines
drivers/thermal/Kconfig +1
-1@@ -143,7 +143,7 @@ config RCAR_THERMAL config KIRKWOOD_THERMAL tristate "Temperature sensor on Marvell Kirkwood SoCs" - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD
I have no objections with this change. So, wrt thermal:
Quoted 10 lines
drivers/thermal/Kconfig +0
-1depends on OF help Support for the Kirkwood thermal sensor driver into the Linux thermal --2.1.0
--
To unsubscribe from this list: send the line "unsubscribe linux-pm" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
Eduardo Bezerra Valentin
PATCH v3 1/1 4/7] leds: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. Use MACH_KIRKWOOD which will be set when kirkwood is built as part of mach-mvebu.
--- drivers/leds/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/leds/Kconfig +2 -2
@@ -410,7 +410,7 @@ config LEDS_MC13783 config LEDS_NS2 tristate "LED support for Network Space v2 GPIO LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD default y help This option enable support for the dual-GPIO LED found on the
@@ -420,7 +420,7 @@ config LEDS_NS2 config LEDS_NETXBIG tristate "LED support for Big Network series LEDs" depends on LEDS_CLASS - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD + depends on MACH_KIRKWOOD default y help This option enable support for LEDs found on the LaCie 2Big
Signature · 1 line
2.1.0
PATCH v3 1/1 5/7] rtc: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. ARCH_MVEBU is sufficient.
--- drivers/rtc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/rtc/Kconfig +1 -1
@@ -1198,7 +1198,7 @@ config RTC_DRV_TX4939 config RTC_DRV_MV tristate "Marvell SoC RTC" - depends on ARCH_KIRKWOOD || ARCH_DOVE || ARCH_MVEBU + depends on ARCH_DOVE || ARCH_MVEBU help If you say yes here you will get support for the in-chip RTC that can be found in some of Marvell's SoC devices, such as
Signature · 1 line
2.1.0
PATCH v3 1/1 6/7] watchdog: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. ARCH_MVEBU is sufficient.
--- drivers/watchdog/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/watchdog/Kconfig +1 -1
@@ -301,7 +301,7 @@ config DAVINCI_WATCHDOG config ORION_WATCHDOG tristate "Orion watchdog" - depends on ARCH_ORION5X || ARCH_KIRKWOOD || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU + depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU select WATCHDOG_CORE help Say Y here if to include support for the watchdog timer
Signature · 1 line
2.1.0
PATCH v3 1/1 7/7] cpufreq: Remove ARCH_KIRKWOOD dependency
In reply to Andrew Lunnmach-kirkwood has been removed, now that kirkwood lives in mach-mvebu. ARCH_MVEBU is sufficient.
--- drivers/cpufreq/Kconfig.arm | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpufreq/Kconfig.arm +1 -1
@@ -119,7 +119,7 @@ config ARM_INTEGRATOR If in doubt, say Y. config ARM_KIRKWOOD_CPUFREQ - def_bool ARCH_KIRKWOOD || MACH_KIRKWOOD + def_bool MACH_KIRKWOOD help This adds the CPUFreq driver for Marvell Kirkwood SoCs.
Signature · 1 line
2.1.0
Viresh Kumar
maintainerPATCH v3 1/1 7/7] cpufreq: Remove ARCH_KIRKWOOD dependency
Quoted 15 lines · Andrew Lunn
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBUis sufficient.Signed-off-by Andrew Lunn <[email protected]>Cc "Rafael J. Wysocki" <[email protected]>Cc Viresh Kumar <[email protected]>--- drivers/cpufreq/Kconfig.arm | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/cpufreq/Kconfig.arm +0
-0
drivers/cpufreq/Kconfig.arm config ARM_INTEGRATOR · line 125
Quoted 8 lines
drivers/cpufreq/Kconfig.arm +1
-1@@ -119,7 +119,7 @@ config ARM_INTEGRATOR If in doubt, say Y. config ARM_KIRKWOOD_CPUFREQ - def_bool ARCH_KIRKWOOD || MACH_KIRKWOOD + def_bool MACH_KIRKWOOD help This adds the CPUFreq driver for Marvell Kirkwood SoCs.
PATCH v3 1/1 0/7] Remove mach-kirkwood
In reply to Andrew LunnQuoted 12 lines · Andrew Lunn
This is mostly a resend of these patches, removing mach-kirkwood. Not all maintainers picked up there patches, which has resulted in some dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that Jason Cooper will submit them for inclusion in an RC. Subsystem maintainers do not need to do anything.
The last patch "cpufreq: Remove
ARCH_KIRKWOODdependency" is new, since what it is removing was added during v3.16-rcX. It follows the pattern of all the other patches.
Quoted 8 lines
Andrew Lunn (7):
cpuidle: kirkwood: RemoveARCH_KIRKWOODdependency
ata: RemoveARCH_KIRKWOODdependency
thermal: RemoveARCH_KIRKWOODdependency
leds: RemoveARCH_KIRKWOODdependency
rtc: RemoveARCH_KIRKWOODdependency
watchdog: RemoveARCH_KIRKWOODdependency
cpufreq: RemoveARCH_KIRKWOODdependency
I have no problems with these changes, but what exactly am I supposed to do?
Rafael
PATCH v3 1/1 0/7] Remove mach-kirkwood
Quoted 22 lines · Rafael J. Wysocki
Quoted 12 lines · Andrew Lunn
This is mostly a resend of these patches, removing mach-kirkwood. Not all maintainers picked up there patches, which has resulted in some dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that Jason Cooper will submit them for inclusion in an RC. Subsystem maintainers do not need to do anything.
The last patch "cpufreq: Remove
ARCH_KIRKWOODdependency" is new, since what it is removing was added during v3.16-rcX. It follows the pattern of all the other patches.Quoted 8 lines
Andrew Lunn (7):
cpuidle: kirkwood: RemoveARCH_KIRKWOODdependency
ata: RemoveARCH_KIRKWOODdependency
thermal: RemoveARCH_KIRKWOODdependency
leds: RemoveARCH_KIRKWOODdependency
rtc: RemoveARCH_KIRKWOODdependency
watchdog: RemoveARCH_KIRKWOODdependency
cpufreq: RemoveARCH_KIRKWOODdependency
Quoted 1 line
I have no problems with these changes, but what exactly am I supposed to do?
Jason will submit the whole series. So an Acked-by: would be nice.
Andrew
PATCH v3 1/1 0/7] Remove mach-kirkwood
Quoted 23 lines · Andrew Lunn
Quoted 22 lines · Rafael J. Wysocki
Quoted 20 lines · Andrew Lunn
This is mostly a resend of these patches, removing mach-kirkwood. Not all maintainers picked up there patches, which has resulted in some dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that Jason Cooper will submit them for inclusion in an RC. Subsystem maintainers do not need to do anything.
The last patch "cpufreq: Remove
ARCH_KIRKWOODdependency" is new, since what it is removing was added during v3.16-rcX. It follows the pattern of all the other patches.Andrew Lunn (7):
cpuidle: kirkwood: RemoveARCH_KIRKWOODdependency
ata: RemoveARCH_KIRKWOODdependency
thermal: RemoveARCH_KIRKWOODdependency
leds: RemoveARCH_KIRKWOODdependency
rtc: RemoveARCH_KIRKWOODdependency
watchdog: RemoveARCH_KIRKWOODdependency
cpufreq: RemoveARCH_KIRKWOODdependency
Quoted 3 lines
Quoted 1 line
I have no problems with these changes, but what exactly am I supposed to do?
Jason will submit the whole series. So an Acked-by: would be nice.
OK, so please regard the cpuidle and cpufreq patches as ACKed.
Rafael
PATCH v3 1/1 0/7] Remove mach-kirkwood
In reply to Andrew LunnAndrew,
Quoted 21 lines · Andrew Lunn
This is mostly a resend of these patches, removing mach-kirkwood. Not all maintainers picked up there patches, which has resulted in some dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that Jason Cooper will submit them for inclusion in an RC. Subsystem maintainers do not need to do anything.
The last patch "cpufreq: Remove
ARCH_KIRKWOODdependency" is new, since what it is removing was added during v3.16-rcX. It follows the pattern of all the other patches.Andrew Lunn (7):
cpuidle: kirkwood: RemoveARCH_KIRKWOODdependency
ata: RemoveARCH_KIRKWOODdependency
thermal: RemoveARCH_KIRKWOODdependency
leds: RemoveARCH_KIRKWOODdependency
rtc: RemoveARCH_KIRKWOODdependency
watchdog: RemoveARCH_KIRKWOODdependency
cpufreq: RemoveARCH_KIRKWOODdependency
Quoted 8 lines
drivers/ata/Kconfig | 2 +- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpuidle/Kconfig.arm | 2 +- drivers/leds/Kconfig | 4 ++-- drivers/rtc/Kconfig | 2 +- drivers/thermal/Kconfig | 2 +- drivers/watchdog/Kconfig | 2 +- 7 files changed, 8 insertions(+), 8 deletions(-)
Applied to mvebu/fixes for v3.17 with all the various Acks. Also, please don't add the extra ']' in the Subject lines, 'git am' threw a gasket on that so I had to manually edit before applying. Not a big deal, just an fyi.
thx,
Jason.