Skip to contentSkip to conversation

Basic build fails

DISCUSSION Arun Kumar 3 participants 4 messages Sep 12, 2014 – Sep 13, 2014

lore
Share & tools
lore

Arun Kumar

author
#0 lore raw

Hi all,

I am new to the yocto project and was following the steps given in the quick start guide. I made a slight change as given in the superuser section.

I used the "fetchall" option to get all the packages first and then started the build, now when i use this command

"bitbake -k core-image-sato" i get the following error

/------------------------------------------------------------------------------------
ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 1784 didn't need to be rerun and 1 failed.
No currently running tasks (2729 of 5634)

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 WARNING message shown.
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /------------------------------------------------------------------------------------

any idea or hint where i might be going wrong?

#1 lore raw
Quoted 13 lines · Arun Kumar

Hi all,

I am new to the yocto project and was following the steps given in the quick start guide. I made a slight change as given in the superuser section.

I used the "fetchall" option to get all the packages first and then started the build, now when i use this command

"bitbake -k core-image-sato" i get the following error

/------------------------------------------------------------------------------------
ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 1784 didn't need to be rerun and 1 failed.
No currently running tasks (2729 of 5634)

Quoted 7 lines

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 WARNING message shown.
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /------------------------------------------------------------------------------------

any idea or hint where i might be going wrong?

You've trimmed the output at just the place where it was telling you what went wrong. Re-run bitbake gcc-cross, and paste the output of that.

Ross

author
#2 lore raw

Thanks for the reply ross, but the build noise is too much form me to put it in here. I will post the last few lines of which i can make some sense, but the rest is somewhat incomprehensible.

/-------------------------------------------------------------------------------

| make[1]: *** [s-attrtab] Killed
| make[1]: *** Waiting for unfinished jobs....
| make[1]: Leaving directory `/home/arun/Documents/Dev/yocto/tmp/work/x86_64-poky-linux/gcc-cross-i586/4.9.1-r0/gcc-4.9.1/build.x86_64-linux.i586-poky-linux/gcc'
| make: *** [all-gcc] Error 2
| ERROR: oe_runmake failed
| WARNING: exit code 1 from a shell command.
| ERROR: Function failed: do_compile (log file is located at /home/arun/Documents/Dev/yocto/build/../tmp/work/x86_64-poky-linux/gcc-cross-i586/4.9.1-r0/temp/log.do_compile.29857)

ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 2728 didn't need to be rerun and 1 failed.
No currently running tasks (307 of 5634)

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /-------------------------------------------------------------------------------------------------------

here is the pastebin link to the whole error http://pastebin.com/Y1JsA8dt
hope this helps

Quoted 27 lines · Ross
Quoted 13 lines · Arun Kumar

Hi all,

I am new to the yocto project and was following the steps given in the quick start guide. I made a slight change as given in the superuser section.

I used the "fetchall" option to get all the packages first and then started the build, now when i use this command

"bitbake -k core-image-sato" i get the following error

/------------------------------------------------------------------------------------
ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 1784 didn't need to be rerun and 1 failed.
No currently running tasks (2729 of 5634)

Quoted 7 lines

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 WARNING message shown.
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /------------------------------------------------------------------------------------

any idea or hint where i might be going wrong?

You've trimmed the output at just the place where it was telling you what went wrong. Re-run bitbake gcc-cross, and paste the output of that.

Ross

#3 lore raw
Quoted 4 lines · Arun Kumar

Thanks for the reply ross, but the build noise is too much form me to put it in here. I will post the last few lines of which i can make some sense, but the rest is somewhat incomprehensible.

/------------------------------------------------------------------------------- | make[1]: *** [s-attrtab] Killed

This is very suspicious - looks like your build may have been killed by running out of memory...

Quoted 10 lines
| make[1]: *** Waiting for unfinished jobs....
| make[1]: Leaving directory `/home/arun/Documents/Dev/yocto/tmp/work/x86_64-poky-linux/gcc-cross-i586/4.9.1-r0/gcc-4.9.1/build.x86_64-linux.i586-poky-linux/gcc'
| make: *** [all-gcc] Error 2
| ERROR: oe_runmake failed
| WARNING: exit code 1 from a shell command.
| ERROR: Function failed: do_compile (log file is located at /home/arun/Documents/Dev/yocto/build/../tmp/work/x86_64-poky-linux/gcc-cross-i586/4.9.1-r0/temp/log.do_compile.29857)

ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 2728 didn't need to be rerun and 1 failed.
No currently running tasks (307 of 5634)

Quoted 7 lines

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /-------------------------------------------------------------------------------------------------------

here is the pastebin link to the whole error http://pastebin.com/Y1JsA8dt
hope this helps

How much memory (RAM+SWAP) does your host build machine have?

Quoted 29 lines · Ross
Quoted 27 lines · Arun Kumar
Quoted 13 lines

Hi all,

I am new to the yocto project and was following the steps given in the quick start guide. I made a slight change as given in the superuser section.

I used the "fetchall" option to get all the packages first and then started the build, now when i use this command

"bitbake -k core-image-sato" i get the following error

/------------------------------------------------------------------------------------
ERROR: Task 595 (/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2729 tasks of which 1784 didn't need to be rerun and 1 failed.
No currently running tasks (2729 of 5634)

Quoted 7 lines

Summary: 1 task failed:
/home/arun/Documents/Dev/yocto/poky/meta/recipes-devtools/gcc/gcc-cross_4.9.bb, do_compile
Summary: There was 1 WARNING message shown.
Summary: There was 1 ERROR message shown, returning a non-zero exit code. /------------------------------------------------------------------------------------

any idea or hint where i might be going wrong?

You've trimmed the output at just the place where it was telling you what went wrong. Re-run bitbake gcc-cross, and paste the output of that.

Ross

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------