Remove the support for the RSI EWS board
PATCH 1/1 Remove the support for the RSI EWS board
The platform is end of life/support and should not clutter the mach-at91 directory with non-DT files. It is therefore removed.
Signed-off-by Josef Holzmayr <[email protected]>
--- arch/arm/mach-at91/Kconfig.non_dt | 6 - arch/arm/mach-at91/Makefile | 1 - arch/arm/mach-at91/board-rsi-ews.c | 232 ------------------------------------- 3 files changed, 239 deletions(-) delete mode 100644 arch/arm/mach-at91/board-rsi-ews.c
arch/arm/mach-at91/Kconfig.non_dt +0 -6
@@ -132,12 +132,6 @@ config MACH_ECO920 bool "eco920" help Select this if you are using the eco920 board - -config MACH_RSI_EWS - bool "RSI Embedded Webserver" - depends on ARCH_AT91RM9200 - help - Select this if you are using RSIs EWS board. endif # ----------------------------------------------------------
arch/arm/mach-at91/Makefile +0 -1
@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o obj-$(CONFIG_MACH_ECO920) += board-eco920.o -obj-$(CONFIG_MACH_RSI_EWS) += board-rsi-ews.o # AT91SAM9260 board-specific support obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
arch/arm/mach-at91/board-rsi-ews.c deleted +0 -232
232 lines not on this page · raw message
Signature · 16 lines
2.1.0 -- _____________________________________________________________ R-S-I Elektrotechnik GmbH & Co. KG Woelkestrasse 11 D-85301 Schweitenkirchen Fon: +49 8444 9204-0 Fax: +49 8444 9204-50 www.rsi-elektrotechnik.de _____________________________________________________________ Amtsgericht Ingolstadt - GmbH: HRB 191328 - KG: HRA 170363 Gesch?ftsf?hrer: Dr.-Ing. Michael Sorg, Dipl.-Ing. Franz Sorg USt-IdNr.: DE 128592548
PATCH 1/1 Remove the support for the RSI EWS board
On 19/09/2014 13:02, Josef Holzmayr :
Quoted 5 lines
The platform is end of life/support and should not clutter the mach-at91 directory with non-DT files. It is therefore removed.
Signed-off-by Josef Holzmayr <[email protected]>
Ok, thanks for having take the action Josef. So obviously:
Acked-by Nicolas Ferre <[email protected]>
I'll try to queue it in our at91-3.18-soc branch.
Best regards,
Quoted 275 lines
--- arch/arm/mach-at91/Kconfig.non_dt | 6 - arch/arm/mach-at91/Makefile | 1 - arch/arm/mach-at91/board-rsi-ews.c | 232 ------------------------------------- 3 files changed, 239 deletions(-) delete mode 100644 arch/arm/mach-at91/board-rsi-ews.carch/arm/mach-at91/Kconfig.non_dt +0
-6@@ -132,12 +132,6 @@ config MACH_ECO920 bool "eco920" help Select this if you are using the eco920 board - -config MACH_RSI_EWS - bool "RSI Embedded Webserver" - depends on ARCH_AT91RM9200 - help - Select this if you are using RSIs EWS board. endif # ----------------------------------------------------------arch/arm/mach-at91/Makefile +0
-1@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o obj-$(CONFIG_MACH_ECO920) += board-eco920.o -obj-$(CONFIG_MACH_RSI_EWS) += board-rsi-ews.o # AT91SAM9260 board-specific support obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.oarch/arm/mach-at91/board-rsi-ews.c deleted +0
-232@@ -1,232 +0,0 @@ -/* -* board-rsi-ews.c -* -* Copyright (C) -* 2005 SAN People, -* 2008-2011 R-S-I Elektrotechnik GmbH & Co. KG -* -* Licensed under GPLv2 or later. -*/ - -#include <linux/types.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/spi/spi.h> -#include <linux/mtd/physmap.h> - -#include <asm/setup.h> -#include <asm/mach-types.h> -#include <asm/irq.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> - -#include <mach/hardware.h> - -#include <linux/gpio.h> - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - -static void __init rsi_ews_init_early (void ) -{ -/* Initialize processor: 18.432 MHz crystal */ -at91_initialize (18432000 ); -} - -/* -* Ethernet -*/ -static struct macb_platform_data rsi_ews_eth_data__initdata = { - .phy_irq_pin =AT91_PIN_PC4 , - .is_rmii =1 , -}; - -/* -* USB Host -*/ -static struct at91_usbh_data rsi_ews_usbh_data__initdata = { - .ports =1 , - .vbus_pin = {-EINVAL , -EINVAL }, - .overcurrent_pin= {-EINVAL , -EINVAL }, -}; - -/* -* SD/MC -*/ -static struct mci_platform_data __initdata rsi_ews_mci0_data = { - .slot[0 ] = { - .bus_width =4 , - .detect_pin =AT91_PIN_PB27 , - .wp_pin =AT91_PIN_PB29 , - }, -}; - -/* -* I2C -*/ -static struct i2c_board_info rsi_ews_i2c_devices[]__initdata = { - { -I2C_BOARD_INFO ("ds1337" ,0x68 ), - }, - { -I2C_BOARD_INFO ("24c01" ,0x50 ), - } -}; - -/* -* LEDs -*/ -static struct gpio_led rsi_ews_leds[] = { - { - .name ="led0" , - .gpio =AT91_PIN_PB6 , - .active_low =0 , - }, - { - .name ="led1" , - .gpio =AT91_PIN_PB7 , - .active_low =0 , - }, - { - .name ="led2" , - .gpio =AT91_PIN_PB8 , - .active_low =0 , - }, - { - .name ="led3" , - .gpio =AT91_PIN_PB9 , - .active_low =0 , - }, -}; - -/* -* DataFlash -*/ -static struct spi_board_info rsi_ews_spi_devices[] = { - {/* DataFlash chip 1*/ - .modalias ="mtd_dataflash" , - .chip_select =0 , - .max_speed_hz =5 *1000 *1000 , - }, - {/* DataFlash chip 2*/ - .modalias ="mtd_dataflash" , - .chip_select =1 , - .max_speed_hz =5 *1000 *1000 , - }, -}; - -/* -* NOR flash -*/ -static struct mtd_partition rsiews_nor_partitions[] = { - { - .name ="boot" , - .offset =0 , - .size =3 *SZ_128K , - .mask_flags =MTD_WRITEABLE - }, - { - .name ="kernel" , - .offset =MTDPART_OFS_NXTBLK , - .size =SZ_2M - (3 *SZ_128K ) - }, - { - .name ="root" , - .offset =MTDPART_OFS_NXTBLK , - .size =SZ_8M - }, - { - .name ="kernelupd" , - .offset =MTDPART_OFS_NXTBLK , - .size =3 *SZ_512K , - .mask_flags =MTD_WRITEABLE - }, - { - .name ="rootupd" , - .offset =MTDPART_OFS_NXTBLK , - .size =9 *SZ_512K , - .mask_flags =MTD_WRITEABLE - }, -}; - -static struct physmap_flash_data rsiews_nor_data = { - .width =2 , - .parts = rsiews_nor_partitions, - .nr_parts =ARRAY_SIZE (rsiews_nor_partitions), -}; - -#define NOR_BASE AT91_CHIPSELECT_0 -#define NOR_SIZE SZ_16M - -static struct resource nor_flash_resources[] = { - { - .start =NOR_BASE , - .end =NOR_BASE +NOR_SIZE -1 , - .flags =IORESOURCE_MEM , - } -}; - -static struct platform_device rsiews_nor_flash = { - .name ="physmap-flash" , - .id =0 , - .dev = { - .platform_data = &rsiews_nor_data, - }, - .resource = nor_flash_resources, - .num_resources =ARRAY_SIZE (nor_flash_resources), -}; - -/* -* Init Func -*/ -static void __init rsi_ews_board_init (void ) -{ -/* Serial */ -/* DBGU on ttyS0. (Rx & Tx only) */ -/* This one is for debugging */ -at91_register_uart (0 ,0 ,0 ); - -/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -/* Dialin/-out modem interface */ -at91_register_uart (AT91RM9200_ID_US1 ,2 ,ATMEL_UART_CTS |ATMEL_UART_RTS - |ATMEL_UART_DTR |ATMEL_UART_DSR |ATMEL_UART_DCD - |ATMEL_UART_RI ); - -/* USART3 on ttyS4. (Rx, Tx, RTS) */ -/* RS485 communication */ -at91_register_uart (AT91RM9200_ID_US3 ,4 ,ATMEL_UART_RTS ); -at91_add_device_serial (); -at91_set_gpio_output (AT91_PIN_PA21 ,0 ); -/* Ethernet */ -at91_add_device_eth (&rsi_ews_eth_data); -/* USB Host */ -at91_add_device_usbh (&rsi_ews_usbh_data); -/* I2C */ -at91_add_device_i2c (rsi_ews_i2c_devices, -ARRAY_SIZE (rsi_ews_i2c_devices)); -/* SPI */ -at91_add_device_spi (rsi_ews_spi_devices, -ARRAY_SIZE (rsi_ews_spi_devices)); -/* MMC */ -at91_add_device_mci (0 , &rsi_ews_mci0_data); -/* NOR Flash */ -platform_device_register (&rsiews_nor_flash); -/* LEDs */ -at91_gpio_leds (rsi_ews_leds,ARRAY_SIZE (rsi_ews_leds)); -} - -MACHINE_START (RSI_EWS ,"RSI EWS" ) -/* Maintainer: Josef Holzmayr <[email protected]> */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = rsi_ews_init_early, - .init_irq = at91_init_irq_default, - .init_machine = rsi_ews_board_init, -MACHINE_END
Signature · 1 line
Nicolas Ferre