enabling ecc on P2041 and QoreIQ familly not valid for memory >= 4GB
Hi ,
I found out an issue when enabling ECC for P2041 platform with an amount of memory of 8GB.
The routine "void dma_meminit(uint val, uint size)" is not adapted to manage memory size greater or equal to 4GB due to the 'uint' type. With this typing the dma_meminit sees 0 as size when memory is for example at 8GB. So the ECC part of the memory is not initialized and when going in memory the code crash.
To correct it you need to use phys_size_t type instead of uint. It is the same thing for all routines that are called by "dma_meminit". I attached a patch that able to correct it easily.
This patch should be integrated in the main branch I think so.
Regards,
Benoit
u-boot-2012.10/arch/powerpc/include/asm/fsl_ddr_sdram.h renamed from u-boot-2012.10/arch/powerpc/include/asm/fsl_ddr_sdram.h:1.1.1.1 +1 -1
@@ -308,7 +308,7 @@#endif #if defined(CONFIG_DDR_ECC ) -extern void ddr_enable_ecc (unsigned int dram_size); +extern void ddr_enable_ecc (phys_size_t dram_size);#endif
u-boot-2012.10/arch/powerpc/include/asm/fsl_dma.h renamed from u-boot-2012.10/arch/powerpc/include/asm/fsl_dma.h:1.1.1.1 +1 -1
@@ -134,7 +134,7 @@void dma_init (void );int dmacpy (phys_addr_t dest,phys_addr_t src,phys_size_t n);#if (defined(CONFIG_DDR_ECC ) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER )) -void dma_meminit (uint val,uint size); +void dma_meminit (uint val,phys_size_t size);#endif #endif
u-boot-2012.10/drivers/dma/fsl_dma.c renamed from u-boot-2012.10/drivers/dma/fsl_dma.c:1.1.1.1 +32 -30
79 lines not on this page · raw message
Quoted 14 lines · Benoit Sansoni
Hi ,
I found out an issue when enabling ECC for P2041 platform with an amount of memory of 8GB.
The routine "voiddma_meminit(uint val, uint size)" is not adapted to manage memory size greater or equal to 4GB due to the 'uint' type. With this typing thedma_meminitsees 0 as size when memory is for example at 8GB. So the ECC part of the memory is not initialized and when going in memory the code crash.
To correct it you need to usephys_size_ttype instead of uint. It is the same thing for all routines that are called by "dma_meminit". I attached a patch that able to correct it easily.
This patch should be integrated in the main branch I think so.
Quoted 3 lines
Regards,
Benoit
This is a valid concern. Some code started when we had far less memory. We need to comb through the code to fix more of them.
York
Hi York,
That what I saw in the code.
Also to test it you need to have the hardware, but the evaluation board P2041rdb for example does not have some ECC signals rooted for DIMM slot. I validated the patch that I sent on a board based on P2041 with 8GB of memory. Obviously it works with 2GB and 4GB.
If you need help, you are welcome.
Thanks for your help
Benoit
Quoted 24 lines · York Sun
Quoted 14 lines · Benoit Sansoni
Hi ,
I found out an issue when enabling ECC for P2041 platform with an amount of memory of 8GB.
The routine "voiddma_meminit(uint val, uint size)" is not adapted to manage memory size greater or equal to 4GB due to the 'uint' type. With this typing thedma_meminitsees 0 as size when memory is for example at 8GB. So the ECC part of the memory is not initialized and when going in memory the code crash.
To correct it you need to usephys_size_ttype instead of uint. It is the same thing for all routines that are called by "dma_meminit". I attached a patch that able to correct it easily.
This patch should be integrated in the main branch I think so.Quoted 3 lines
Regards,
BenoitThis is a valid concern. Some code started when we had far less memory. We need to comb through the code to fix more of them.
York
Signature · 6 lines
Benoit SANSONI Kontron Modular Computers S.A.S 150 rue Marcelin Berthelot - ZI Toulon Est - BP 244 83078 TOULON Cedex 9 - FRANCE E-mail: benoit.sansoni at kontron.com TEL: +33 (0)4 98 16 33 68
Benoit,
If your interest is in initializing DDR for ECC, you don't have use dma_meminit(). There is a better and faster way to do so. All Freescale modern DDR controllers support this feature. All you have to do is to define these macros
CONFIG_DDR_ECCCONFIG_ECC_INIT_VIA_DDRCONTROLLERCONFIG_MEM_INIT_VALUE
There are plenty of example for you to follow.
But again, we should fix the DMA function anyway.
York
Quoted 41 lines · Benoit Sansoni
Hi York,
That what I saw in the code.
Also to test it you need to have the hardware, but the evaluation board P2041rdb for example does not have some ECC signals rooted for DIMM slot. I validated the patch that I sent on a board based on P2041 with 8GB of memory. Obviously it works with 2GB and 4GB.
If you need help, you are welcome.
Thanks for your help
BenoitQuoted 24 lines · York Sun
Quoted 14 lines · Benoit Sansoni
Hi ,
I found out an issue when enabling ECC for P2041 platform with an amount of memory of 8GB.
The routine "voiddma_meminit(uint val, uint size)" is not adapted to manage memory size greater or equal to 4GB due to the 'uint' type. With this typing thedma_meminitsees 0 as size when memory is for example at 8GB. So the ECC part of the memory is not initialized and when going in memory the code crash.
To correct it you need to usephys_size_ttype instead of uint. It is the same thing for all routines that are called by "dma_meminit". I attached a patch that able to correct it easily.
This patch should be integrated in the main branch I think so.Quoted 3 lines
Regards,
BenoitThis is a valid concern. Some code started when we had far less memory. We need to comb through the code to fix more of them.
York
York,
I am going to check out the method that you talk about. For now the fix allow me to boot our board with 8GB it is a good step for me.
Thanks
Benoit
Quoted 60 lines · York Sun
Benoit,
If your interest is in initializing DDR for ECC, you don't have use
dma_meminit(). There is a better and faster way to do so. All Freescale modern DDR controllers support this feature. All you have to do is to define these macros
CONFIG_DDR_ECCCONFIG_ECC_INIT_VIA_DDRCONTROLLERCONFIG_MEM_INIT_VALUEThere are plenty of example for you to follow.
But again, we should fix the DMA function anyway.
York
Quoted 9 lines · Benoit Sansoni
Hi York,
That what I saw in the code.
Also to test it you need to have the hardware, but the evaluation board P2041rdb for example does not have some ECC signals rooted for DIMM slot. I validated the patch that I sent on a board based on P2041 with 8GB of memory. Obviously it works with 2GB and 4GB.
Quoted 31 lines
If you need help, you are welcome.
Thanks for your help
BenoitQuoted 24 lines · York Sun
Quoted 14 lines · Benoit Sansoni
Hi ,
I found out an issue when enabling ECC for P2041 platform with an amount of memory of 8GB.
The routine "voiddma_meminit(uint val, uint size)" is not adapted to manage memory size greater or equal to 4GB due to the 'uint' type. With this typing thedma_meminitsees 0 as size when memory is for example at 8GB. So the ECC part of the memory is not initialized and when going in memory the code crash.
To correct it you need to usephys_size_ttype instead of uint. It is the same thing for all routines that are called by "dma_meminit". I attached a patch that able to correct it easily.
This patch should be integrated in the main branch I think so.Quoted 3 lines
Regards,
BenoitThis is a valid concern. Some code started when we had far less memory. We need to comb through the code to fix more of them.
York
.
Signature · 6 lines
Benoit SANSONI Kontron Modular Computers S.A.S 150 rue Marcelin Berthelot - ZI Toulon Est - BP 244 83078 TOULON Cedex 9 - FRANCE E-mail: benoit.sansoni at kontron.com TEL: +33 (0)4 98 16 33 68
Quoted 24 lines · Benoit Sansoni
York,
I am going to check out the method that you talk about. For now the fix allow me to boot our board with 8GB it is a good step for me.
Thanks
BenoitQuoted 14 lines · York Sun
Benoit,
If your interest is in initializing DDR for ECC, you don't have use
dma_meminit(). There is a better and faster way to do so. All Freescale modern DDR controllers support this feature. All you have to do is to define these macros
CONFIG_DDR_ECCCONFIG_ECC_INIT_VIA_DDRCONTROLLERCONFIG_MEM_INIT_VALUEThere are plenty of example for you to follow.
But again, we should fix the DMA function anyway.
Benoit,
Have you tried my suggestion?
York
Hi York,
Sorry for the delay. I was in holidays. I am back at work today. Yes I have tried the other method that you proposed.
It works perfectly and It seems that this method initialized the ECC in a faster manner.
I faced a stability issue during ddr initialization. To resolve it I deactivate the autocalibration as recommended in the erratum num A-003474. So for me the u-boot release that I am currently using is u-boot-2012.10 and in the file u-boot-2012.10/arch/powerpc/cpu/mpc85xx/ddr-gen3.c I modified it
depending my ddr ram timing :
out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
/*dataT = fsl_dbg_timing();*/
dataT = 0x9;
out_be32(&ddr->timing_cfg_2, (regs->timing_cfg_2 & 0xf07fffff) |
(dataT<<23));
out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
out_be32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3);
out_be32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4);
out_be32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5);
out_be32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6);
out_be32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7);
out_be32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8);
out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
out_be32(&ddr->init_addr, regs->ddr_init_addr);
out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);So for me the timing_cfg_2 must be set at a deterministic value to avoid stability issue when the CONFIG_SYS_FSL_ERRATUM_DDR_A003474 flag is set.
Many thanks
Benoit
Quoted 33 lines · York Sun
Quoted 24 lines · Benoit Sansoni
York,
I am going to check out the method that you talk about. For now the fix allow me to boot our board with 8GB it is a good step for me.
Thanks
BenoitQuoted 14 lines · York Sun
Benoit,
If your interest is in initializing DDR for ECC, you don't have use
dma_meminit(). There is a better and faster way to do so. All Freescale modern DDR controllers support this feature. All you have to do is to define these macros
CONFIG_DDR_ECCCONFIG_ECC_INIT_VIA_DDRCONTROLLERCONFIG_MEM_INIT_VALUEThere are plenty of example for you to follow.
But again, we should fix the DMA function anyway.
Benoit,
Have you tried my suggestion?
York
Signature · 6 lines
Benoit SANSONI Software Engineer Kontron 150 rue Marcelin Berthelot | BP 244 - ZI Toulon-Est | 83078 Toulon Cedex 9 | France P: +33 (0)4 98 16 33 68 benoit.sansoni at kontron.com
Benoit,
Since you should and you have used the suggested method to initialize ECC, I am going to close this patch as N/A. I will find some time to clean up the size variable.
I will follow up with you on the other thread regarding dcache issue.
York
Quoted 79 lines · Benoit Sansoni
Hi York,
Sorry for the delay. I was in holidays. I am back at work today. Yes I have tried the other method that you proposed.
It works perfectly and It seems that this method initialized the ECC in a faster manner.I faced a stability issue during ddr initialization. To resolve it I deactivate the autocalibration as recommended in the erratum num A-003474. So for me the u-boot release that I am currently using is u-boot-2012.10 and in the file
u-boot-2012.10/arch/powerpc/cpu/mpc85xx/ddr-gen3.cI modified it
depending my ddr ram timing :out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3); out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0); out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1); /*dataT = fsl_dbg_timing();*/ dataT = 0x9; out_be32(&ddr->timing_cfg_2, (regs->timing_cfg_2 & 0xf07fffff) | (dataT<<23)); out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2); out_be32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3); out_be32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4); out_be32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5); out_be32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6); out_be32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7); out_be32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8); out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl); out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); out_be32(&ddr->sdram_data_init, regs->ddr_data_init); out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); out_be32(&ddr->init_addr, regs->ddr_init_addr); out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);So for me the
timing_cfg_2must be set at a deterministic value to avoid stability issue when theCONFIG_SYS_FSL_ERRATUM_DDR_A003474flag is set.Many thanks
BenoitQuoted 33 lines · York Sun
Quoted 24 lines · Benoit Sansoni
York,
I am going to check out the method that you talk about. For now the fix allow me to boot our board with 8GB it is a good step for me.
Thanks
BenoitQuoted 14 lines · York Sun
Benoit,
If your interest is in initializing DDR for ECC, you don't have use
dma_meminit(). There is a better and faster way to do so. All Freescale modern DDR controllers support this feature. All you have to do is to define these macros
CONFIG_DDR_ECCCONFIG_ECC_INIT_VIA_DDRCONTROLLERCONFIG_MEM_INIT_VALUEThere are plenty of example for you to follow.
But again, we should fix the DMA function anyway.
Benoit,
Have you tried my suggestion?
York