Revert "ath9k_hw: reduce ANI firstep range for older chips"
PATCH 1/3 Revert "ath9k_hw: reduce ANI firstep range for older chips"
This reverts commit 09efc56345be4146ab9fc87a55c837ed5d6ea1ab
I've received reports that this change is decreasing throughput in some rare conditions on an AR9280 based device
--- drivers/net/wireless/ath/ath9k/ar5008_phy.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath9k/ar5008_phy.c +3 -1
@@ -1004,9 +1004,11 @@ static bool ar5008_hw_ani_control_new(struct ath_hw *ah,case ATH9K_ANI_FIRSTEP_LEVEL :{u32 level = param; - value = level; + value = level *2 ;REG_RMW_FIELD (ah,AR_PHY_FIND_SIG ,AR_PHY_FIND_SIG_FIRSTEP , value); +REG_RMW_FIELD (ah,AR_PHY_FIND_SIG_LOW , +AR_PHY_FIND_SIG_FIRSTEP_LOW , value);if (level != aniState->firstepLevel) { ath_dbg(common, ANI,
Signature · 1 line
2.0.4
PATCH 2/3 ath9k_hw: reduce ANI spur immunity setting on HT40 extension channel
The cycpwr_thr1 value needs to be lower on the extension channel than on the control channel, similar to how the register settings are programmed in the initvals.
Also drop the unnecessary check for HT40 - this register can always be written. This patch has been reported to improve HT40 stability and throughput in some environments.
--- drivers/net/wireless/ath/ath9k/ar5008_phy.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath9k/ar5008_phy.c +2 -3
@@ -1042,9 +1042,8 @@ static bool ar5008_hw_ani_control_new(struct ath_hw *ah,REG_RMW_FIELD (ah,AR_PHY_TIMING5 ,AR_PHY_TIMING5_CYCPWR_THR1 , value); -if (IS_CHAN_HT40 (ah->curchan)) -REG_RMW_FIELD (ah,AR_PHY_EXT_CCA , -AR_PHY_EXT_TIMING5_CYCPWR_THR1 , value); +REG_RMW_FIELD (ah,AR_PHY_EXT_CCA , +AR_PHY_EXT_TIMING5_CYCPWR_THR1 , value -1 );if (level != aniState->spurImmunityLevel) { ath_dbg(common, ANI,
Signature · 1 line
2.0.4
PATCH 3/3 ath9k_hw: fix PLL clock initialization for newer SoC
In reply to Felix FietkauOn AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL register changed. This currently breaks at least 5/10 MHz operation. AR933x uses the old layout.
It might also have been causing other stability issues because of the different location of the PLL_BYPASS bit which needs to be set during PLL clock initialization.
This patch also removes more instances of hardcoded register values in favor of properly computed ones with the PLL_BYPASS bit added.
--- drivers/net/wireless/ath/ath9k/ar9003_phy.c | 24 +++++++++++++++++++++++- drivers/net/wireless/ath/ath9k/hw.c | 9 ++++++--- drivers/net/wireless/ath/ath9k/reg.h | 11 +++++++++++ 3 files changed, 40 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath9k/ar9003_phy.c +23 -1
@@ -517,6 +517,23 @@ static void ar9003_hw_spur_mitigate(struct ath_hw *ah,ar9003_hw_spur_mitigate_ofdm (ah, chan); } +static u32 ar9003_hw_compute_pll_control_soc (struct ath_hw *ah, +struct ath9k_channel *chan) +{ +u32 pll; + + pll =SM (0x5 ,AR_RTC_9300_SOC_PLL_REFDIV ); + +if (chan &&IS_CHAN_HALF_RATE (chan)) + pll |=SM (0x1 ,AR_RTC_9300_SOC_PLL_CLKSEL ); +else if (chan &&IS_CHAN_QUARTER_RATE (chan)) + pll |=SM (0x2 ,AR_RTC_9300_SOC_PLL_CLKSEL ); + + pll |=SM (0x2c ,AR_RTC_9300_SOC_PLL_DIV_INT ); + +return pll; +} +static u32 ar9003_hw_compute_pll_control (struct ath_hw *ah,struct ath9k_channel *chan) {
@@ -1781,7 +1798,12 @@ void ar9003_hw_attach_phy_ops(struct ath_hw *ah) priv_ops->rf_set_freq = ar9003_hw_set_channel; priv_ops->spur_mitigate_freq = ar9003_hw_spur_mitigate; - priv_ops->compute_pll_control = ar9003_hw_compute_pll_control; + +if (AR_SREV_9340 (ah) ||AR_SREV_9550 (ah) ||AR_SREV_9531 (ah)) + priv_ops->compute_pll_control = ar9003_hw_compute_pll_control_soc; +else + priv_ops->compute_pll_control = ar9003_hw_compute_pll_control; + priv_ops->set_channel_regs = ar9003_hw_set_channel_regs; priv_ops->init_bb = ar9003_hw_init_bb; priv_ops->process_ini = ar9003_hw_process_ini;
drivers/net/wireless/ath/ath9k/hw.c +6 -3
@@ -704,6 +704,8 @@ static void ath9k_hw_init_pll(struct ath_hw *ah, {u32 pll; + pll =ath9k_hw_compute_pll_control (ah, chan); +if (AR_SREV_9485 (ah) ||AR_SREV_9565 (ah)) {/* program BB PLL ki and kd value, ki=0x4, kd=0x40 */ REG_RMW_FIELD(ah, AR_CH0_BB_DPLL2,
@@ -754,7 +756,8 @@ static void ath9k_hw_init_pll(struct ath_hw *ah,REG_RMW_FIELD (ah,AR_CH0_DDR_DPLL3 ,AR_CH0_DPLL3_PHASE_SHIFT ,0x1 ); -REG_WRITE (ah,AR_RTC_PLL_CONTROL ,0x1142c ); +REG_WRITE (ah,AR_RTC_PLL_CONTROL , + pll |AR_RTC_9300_PLL_BYPASS );udelay (1000 );/* program refdiv, nint, frac to RTC register */
@@ -770,7 +773,8 @@ static void ath9k_hw_init_pll(struct ath_hw *ah, }else if (AR_SREV_9340 (ah) ||AR_SREV_9550 (ah) ||AR_SREV_9531 (ah)) {u32 regval, pll2_divint, pll2_divfrac, refdiv; -REG_WRITE (ah,AR_RTC_PLL_CONTROL ,0x1142c ); +REG_WRITE (ah,AR_RTC_PLL_CONTROL , + pll |AR_RTC_9300_SOC_PLL_BYPASS );udelay (1000 );REG_SET_BIT (ah,AR_PHY_PLL_MODE ,0x1 <<16 );
@@ -843,7 +847,6 @@ static void ath9k_hw_init_pll(struct ath_hw *ah,udelay (1000 ); } - pll =ath9k_hw_compute_pll_control (ah, chan);if (AR_SREV_9565 (ah)) pll |=0x40000 ;REG_WRITE (ah,AR_RTC_PLL_CONTROL , pll);
drivers/net/wireless/ath/ath9k/reg.h +11 -0
@@ -1240,12 +1240,23 @@ enum {#define AR_CH0_DPLL3_PHASE_SHIFT_S 23#define AR_PHY_CCA_NOM_VAL_2GHZ -118 +#define AR_RTC_9300_SOC_PLL_DIV_INT 0x0000003f +#define AR_RTC_9300_SOC_PLL_DIV_INT_S 0 +#define AR_RTC_9300_SOC_PLL_DIV_FRAC 0x000fffc0 +#define AR_RTC_9300_SOC_PLL_DIV_FRAC_S 6 +#define AR_RTC_9300_SOC_PLL_REFDIV 0x01f00000 +#define AR_RTC_9300_SOC_PLL_REFDIV_S 20 +#define AR_RTC_9300_SOC_PLL_CLKSEL 0x06000000 +#define AR_RTC_9300_SOC_PLL_CLKSEL_S 25 +#define AR_RTC_9300_SOC_PLL_BYPASS 0x08000000 +#define AR_RTC_9300_PLL_DIV 0x000003ff#define AR_RTC_9300_PLL_DIV_S 0#define AR_RTC_9300_PLL_REFDIV 0x00003C00#define AR_RTC_9300_PLL_REFDIV_S 10#define AR_RTC_9300_PLL_CLKSEL 0x0000C000#define AR_RTC_9300_PLL_CLKSEL_S 14 +#define AR_RTC_9300_PLL_BYPASS 0x00010000#define AR_RTC_9160_PLL_DIV 0x000003ff#define AR_RTC_9160_PLL_DIV_S 0
Signature · 1 line
2.0.4
Quoted 4 lines · Felix Fietkau
This reverts commit
09efc56345be4146ab9fc87a55c837ed5d6ea1abI've received reports that this change is decreasing throughput in some rare conditions on an AR9280 based device
Wasn't the original patch for improving stability ? Won't reverting it reintroduce the earlier situation ?
If ANI issues/regressions for pre-AR9003 chips are still arising, I wonder what we have gained by the switch and if the new algorithm is a good fit for the older chips.
At least for SoC chips, people will report it to OpenWrt. For PC-OEM cards, users will just say that the card sucks and move on...
Sujith
Quoted 8 lines · Sujith Manoharan
Quoted 4 lines · Felix Fietkau
This reverts commit
09efc56345be4146ab9fc87a55c837ed5d6ea1abI've received reports that this change is decreasing throughput in some rare conditions on an AR9280 based device
Wasn't the original patch for improving stability ? Won't reverting it reintroduce the earlier situation ?
The issues that were slightly improved by this patch were fixed in a different way later. This change has been tested in OpenWrt for 3 weeks now.
Quoted 3 lines
If ANI issues/regressions for pre-AR9003 chips are still arising, I wonder what we have gained by the switch and if the new algorithm is a good fit for the older chips.
After switching to the new algorithm, a large number of users reported a very significant increase in stability. Back then, overall stability of ath9k was a lot worse than it is now, and a much larger number of users were having trouble with it.
Additionally, the new algorithm is much easier to understand and tune - the old code (especially the one with both algorithms combined) was an incomprehensible mess of spaghetti code. I still believe the new algorithm is better for pre-AR9003 than the old one, just the callback that applies the settings needs a bit more fine tuning.
The ANI issues that I'm finding these days affect a *much* smaller number of users, and are less severe than what we've been dealing with during the time of the switch.
Quoted 2 lines
At least for SoC chips, people will report it to OpenWrt. For PC-OEM cards, users will just say that the card sucks and move on...
For pre-AR9003, most devices used with OpenWrt actually use exactly the same chips as PC-OEM cards.
- Felix
Quoted 2 lines · Felix Fietkau
For pre-AR9003, most devices used with OpenWrt actually use exactly the same chips as PC-OEM cards.
Yes, that is true. We split the SoC/PC-OEM chip lines in AR9003. Sorry for the noise. ;)
Sujith