mx6qsabreauto: Add HDMI support

PATCH New Fabio Estevam 2 participants 4 messages Sep 22, 2014 – Oct 21, 2014

lore

Share & tools

lore

Fabio Estevam

author

2014-09-22 16:55 UTC #0 lore raw

PATCH 1/2 mx6qsabreauto: Add HDMI support

Let HDMI splash screen support work by default.

Signed-off-by Fabio Estevam <[email protected]>

---
 board/freescale/mx6qsabreauto/mx6qsabreauto.c | 60 ++++++++++++++++++++++++++-
 include/configs/mx6qsabreauto.h               | 17 ++++++++
 2 files changed, 76 insertions(+), 1 deletion(-)

board/freescale/mx6qsabreauto/mx6qsabreauto.c +59 -1

index dd6d2a6..6e9b4d8 100644
@@ -23,6 +23,9 @@
 #include <netdev.h>
 #include <asm/arch/sys_proto.h>
 #include <i2c.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/imx-common/video.h>
+#include <asm/arch/crm_regs.h>
 
 DECLARE_GLOBAL_DATA_PTR;

@@ -234,10 +237,65 @@ u32 get_board_rev(void)
 	return (get_cpu_rev() & ~(0xF << 8)) | rev;
 }
 
+#if defined(CONFIG_VIDEO_IPUV3)
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED,
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
-
+#ifdef CONFIG_VIDEO_IPUV3
+	setup_display();
+#endif
 	return 0;
 }

include/configs/mx6qsabreauto.h +17 -0

index 0ab3127..48fec6f 100644
@@ -45,4 +45,21 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		100000
 
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */

Signature · 1 line

1.9.1

Fabio Estevam

author

2014-09-22 16:55 UTC #1 lore raw

PATCH 2/2 mx6sabre_common: Add HDMI config to common code

HDMI config options can be placed into the common mx6sabre_common.h file to avoid duplication.

Signed-off-by Fabio Estevam <[email protected]>

---
 include/configs/mx6qsabreauto.h   | 17 -----------------
 include/configs/mx6sabre_common.h | 17 +++++++++++++++++
 include/configs/mx6sabresd.h      | 17 -----------------
 3 files changed, 17 insertions(+), 34 deletions(-)

include/configs/mx6qsabreauto.h +0 ~~-17~~

index 48fec6f..0ab3127 100644
@@ -45,21 +45,4 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		100000
 
-/* Framebuffer */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_IPUV3
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IPUV3_CLK 260000000
-#define CONFIG_IMX_HDMI
-#define CONFIG_IMX_VIDEO_SKIP
-
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */

include/configs/mx6sabre_common.h +17 -0

index e59a3b4..4e80237 100644
@@ -260,4 +260,21 @@
 #define CONFIG_CMD_CACHE
 #endif
 
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+
 #endif                         /* __MX6QSABRE_COMMON_CONFIG_H */

include/configs/mx6sabresd.h +0 ~~-17~~

index e666ebb..938030d 100644
@@ -32,23 +32,6 @@
 #define CONFIG_SYS_MMC_ENV_DEV		1	/* SDHC3 */
 #endif
 
-/* Framebuffer */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_IPUV3
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IPUV3_CLK 260000000
-#define CONFIG_IMX_HDMI
-#define CONFIG_IMX_VIDEO_SKIP
-
 #define CONFIG_CMD_PCI
 #ifdef CONFIG_CMD_PCI
 #define CONFIG_PCI

Signature · 1 line

1.9.1

Stefano Babic

2014-10-21 12:12 UTC #2 lore raw

PATCH 2/2 mx6sabre_common: Add HDMI config to common code

Quoted 5 lines · Fabio Estevam

HDMI config options can be placed into the common mx6sabre_common.h file to avoid duplication.
Signed-off-by Fabio Estevam <[email protected]>
---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Stefano Babic

2014-10-21 12:12 UTC #3 lore raw

PATCH 1/2 mx6qsabreauto: Add HDMI support

In reply to Fabio Estevam

Quoted 4 lines · Fabio Estevam

Let HDMI splash screen support work by default.
Signed-off-by Fabio Estevam <[email protected]>
---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================