Skip to contentSkip to conversation

powerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND

PATCH New Ashish Kumar 2 participants 2 messages Oct 7, 2014 – Nov 14, 2014

lore
Share & tools
lore

Ashish Kumar

author
#0 lore raw

PATCH 1/1 powerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND

* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather than using static partitions in device tree

Signed-off-by Ashish Kumar <[email protected]>
---
 board/freescale/bsc9131rdb/bsc9131rdb.c |   11 +++++++++++
 include/configs/BSC9131RDB.h            |   17 +++++++++++++++++
 2 files changed, 28 insertions(+), 0 deletions(-)
board/freescale/bsc9131rdb/bsc9131rdb.c +11 -0
index 7fe4ae7..9146f49 100644
@@ -15,6 +15,9 @@
 #include <fdt_support.h>
 #include <fsl_mdio.h>
 #include <tsec.h>
+#include <jffs2/load_kernel.h>
+#include <mtd_node.h>
+#include <flash.h>
 #include <netdev.h>
 
 

@@ -50,6 +53,11 @@ int checkboard(void)
 }
 
 #if defined(CONFIG_OF_BOARD_SETUP)
+#ifdef CONFIG_FDT_FIXUP_PARTITIONS
+struct node_info nodes[] = {
+	{ "fsl,ifc-nand",		MTD_DEV_TYPE_NAND, },
+};
+#endif
 void ft_board_setup(void *blob, bd_t *bd)
 {
 	phys_addr_t base;

@@ -61,6 +69,9 @@ void ft_board_setup(void *blob, bd_t *bd)
 	size = getenv_bootm_size();
 
 	fdt_fixup_memory(blob, (u64)base, (u64)size);
+#ifdef CONFIG_FDT_FIXUP_PARTITIONS
+	fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
+#endif
 
 	fdt_fixup_dr_usb(blob, bd);
 }
include/configs/BSC9131RDB.h +17 -0
index 56a3e94..9945dfb 100644
@@ -393,6 +393,23 @@ extern unsigned long get_sdram_size(void);
 #endif
 
 /*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nand0=ff800000.flash,"
+#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \
+			"8m(kernel),512k(dtb),-(fs)"
+/*
+ * Override partitions in device tree using info
+ * in "mtdparts" environment variable
+ */
+#ifdef CONFIG_CMD_MTDPARTS
+#define CONFIG_FDT_FIXUP_PARTITIONS
+#endif
+
+/*
  * Environment Configuration
  */
Signature · 1 line
1.7.6.GIT
#1 lore raw

PATCH 1/1 powerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND

Quoted 7 lines · Ashish Kumar

* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather than using static partitions in device tree

Signed-off-by Ashish Kumar <[email protected]>

---

Applied to u-boot-mpc85xx master. Thanks.

York